Agilent USB3, Slide - 1. Agilent. USB3 Test Fixture Characterization. 10 MHz to 20 GHz March 12,
|
|
- Milo Stokes
- 5 years ago
- Views:
Transcription
1 Agilent USB, Slide 1 Agilent USB Test Fixture Characterization 10 MHz to 20 GHz March 12, 2009
2 Agilent USB, Slide 2 Measurement Summary A prototype Agilent USB test fixture was measured using a 4port PNA, N520A, over a frequency range of 10 MHz to 20 GHz Several permutations of the fixture and cable assembly were measured, including the following (10 measurements, total): Fullpath Tx to Rx differential pairs from TypeA to TypeB including the test fixture and mated connectors (2 measurements) Fixture only with connector receptacles removed from the board, both Tx and Rx on TypeA and TypeB (4 measurements) Fixture thru unmated connector with the board receptacle probed on the connector contacts. Tx (TypeA and Rx (TypeB) only (2 measurements) Fixture thru mated connector with cable detached from the cable plug. Tx (TypeA and Rx (TypeB) only (2 measurements) The crosstalk performance was not measured
3 Agilent USB, Slide HighFrequency Measurement Setup
4 Agilent USB, Slide 4 Measurement Equipment used: 26 GHz coaxial cables (.5mm SMAcompatible connectors) Agilent Technologies N520A 4port PNA Agilent Technologies 85052D Coaxial Calibration Kit GGB Industries 40A750GSSGDP (dual probes) GGB CS800 dual calibration substrate Agilent Advanced Design System software (ADS 2008U2) Picture of setup shown on following slide Vector Network Analyzer settings: Start frequency: 10 MHz Stop frequency: 20 GHz Number of Points: 801, Linear Frequency Sweep Input power: 0 dbm (equivalent to 0.6Vpp into 50Ω) Calibration kit: 85052D, SOLT (short, open, load and thru) Calibration kit: GGB CS800 Calibration Kit 4port, Adapter Removal Calibration (qty=2 SMA, qty=2 probes)
5 Agilent USB, Slide 5 Sample Setup and Definitions Four Configurations 1. Full Path (4port SMA cal) 2. Connector Pads. Connector Receptacle Note the copper foil tooling for Gnd. This is present on each probe location on the PCB and in the connectors 4. Connector Plug Port Assignments for SMA to probe configurations + SMA Diff P1 Port 1 Port Port 2 Port 4 + Probe Diff P2
6 Agilent USB, Slide 6 Full Path TypeA Tx to TypeB Rx A Tx B Rx Full path uses 4port 2.92 mm coax calibration with 85052D cal kit
7 Agilent USB, Slide 7 Connector Type A Tx Board Only Connector pads probed on TOP w/ Gnd Foil
8 Agilent USB, Slide 8 Connector Type A Rx Board Only Connector pads probed on BOTTOM (not shown)
9 Agilent USB, Slide 9 Connector Type A Rx Board + Receptacle Rx ONLY measured due to tooling difficulties
10 Agilent USB, Slide 10 Connector Type A Rx Board + Mated Connector Rx ONLY measured
11 Agilent USB, Slide Full Path (4port SMA cal) Full Path TypeB Tx to TypeA Rx A Rx B Tx Full path uses 4port 2.92 mm coax calibration with 85052D cal kit
12 Agilent USB, Slide 12 Connector Type B Tx Board Only Connector pads probed on TOP w/ Gnd Foil
13 Agilent USB, Slide 1 Connector Type B Rx Board Only Connector pads probed on BOTTOM (not shown)
14 Agilent USB, Slide 14 Connector Type B Rx Board + Receptacle TypeA shown; Rx ONLY measured due to tooling difficulties
15 Agilent USB, Slide 15 Connector Type B Rx Board + Mated Connector Rx ONLY measured due to tooling difficulties
16 Agilent USB, Slide 16 Conclusions A prototype Agilent USB test fixture was measured using a 4port PNA, N520A, over a frequency range of 10 MHz to 20 GHz Several permutations of the fixture and cable assembly were measured, including the following (10 measurements, total): Fullpath Tx to Rx differential pairs from TypeA to TypeB including the test fixture and mated connectors (2 measurements) Fixture only with connector receptacles removed from the board, both Tx and Rx on TypeA and TypeB (4 measurements) Fixture thru unmated connector with the board receptacle probed on the connector contacts. Tx (TypeA and Rx (TypeB) only (2 measurements) Fixture thru mated connector with cable detached from the cable plug. Tx (TypeA and Rx (TypeB) only (2 measurements) The crosstalk performance was not measured
RF Characterization Report
RF058 Series Cable Assemblies RF058-01BJ1-01BJ1-0150 RF058-01SB1-01SB1-0150 RF058-01SP1-01SP1-0150 Description: RF Cable Assembly, 50Ohm, RG058 Coaxial Cable Samtec Inc. WWW.SAMTEC.COM Phone: 812-944-6733
More informationKeysight MOI for USB Type-C Cable Assemblies Compliance Tests Using Keysight M937XA Multiport PXIe VNA
Revision 1.01 Feb-24, 2017 Universal Serial Bus Type-C TM Specification Revision 1.1 Keysight Method of Implementation (MOI) for USB Type-C TM Cables Assemblies Compliance Tests Using Keysight For Type-C
More informationRF Probing With Rohde & Schwarz ZNB VNA. PacketMicro, Inc Wyatt Drive, Suite 9, Santa Clara, CA
RF Probing With Rohde & Schwarz ZNB VNA PacketMicro, Inc. 1900 Wyatt Drive, Suite 9, Santa Clara, CA 95054 www.packetmicro.com Outline Why RF Probing Page 3 4 S-Probe Overview Page 5-8 RF Probing Tips
More informationKeysight MOI for USB Type-C Cable Assemblies Compliance Tests Using Keysight M937XA Multiport PXIe VNA
Revision 1.00 Apr-14, 2016 Universal Serial Bus Type-C TM Specification Revision 1.1 Keysight Method of Implementation (MOI) for USB Type-C TM Cables Assemblies Compliance Tests Using Keysight For Type-C
More informationGT Micro D High Speed Characterization Report For Differential Data Applications. Micro-D High Speed Characterization Report
GT-14-19 Micro D For Differential Data Applications GMR7580-9S1BXX PCB Mount MWDM2L-9P-XXX-XX Cable Mount Revision History Rev Date Approved Description A 4/10/2014 C. Parsons/D. Armani Initial Release
More informationKeysight MOI for USB 2.0 Connectors & Cable Assemblies Compliance Tests
Revision 1.10 October 18, 2016 Universal Serial Bus Specification Revision 2.0 Keysight Method of Implementation (MOI) for USB 2.0 Connectors and Cables Assemblies Compliance Tests Using Keysight E5071C
More informationRF Characterization Report
RF174 Series Cable Assemblies RF174-01SP1-01SP1-0306 RF174-01RP1-01RP1-0308 RF174-01BJ1-01BJ1-0306 RF174-01BR1-01BR1-0306 RF174-02SJ1-02SJ1-0307 RF174-02RP1-02RP1-0307 RF174-02SP1-02SP1-0307 RF174-03SP1-03SP1-0310
More informationKeysight N7015A/16A Type-C Test Kit. User Guide
Keysight N7015A/16A Type-C Test Kit User Guide Notices Keysight Technologies 2015, 2016 No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval
More informationAgilent RF Network Analyzers PNA Series
Agilent RF Network Analyzers PNA Series Configuration Guide E8356A E8357A E8358A 300 khz to 3 GHz 300 khz to 6 GHz 300 khz to 9 GHz System Configuration Summary This summary lists the main components required
More informationWhat We Do. Fixturing and Fixture Removal for Multiport Devices with Non-Standard RF Interfaces. Fully automate for: Speed, Accuracy, Ease of Use
Fixturing and Fixture Removal for Multiport Devices with Non-Standard RF Interfaces What We Do Fully automate for: Speed, Accuracy, Ease of Use Calibration Validation To give confidence in test results
More informationChannels for Consideration by the Signaling Ad Hoc
Channels for Consideration by the Signaling Ad Hoc John D Ambrosia Tyco Electronics Adam Healey, Agere Systems IEEE P802.3ap Signaling Ad Hoc September 17, 2004 Two-Connector Topology N2 H B September,
More informationE5071C Adjustment Program. <Agilent Service Center Use Only> Operation Manual. Second Edition. Agilent Part No. N/A
E5071C Adjustment Program Operation Manual Second Edition Agilent Part No. N/A November 2006 Notices The information contained in this document is subject to change without notice. This document contains
More informationSuccessfully negotiating the PCI EXPRESS 2.0 Super Highway Towards Full Compliance
the PCI EXPRESS 2.0 Super Highway Towards Full Compliance Page 1 Agenda Introduction PCIe 2.0 changes from 1.0a/1.1 Spec 5GT/s Challenges Error Correction Techniques Test tool and fixture changes Agilent
More informationTN Vector Network Analyzer Calibrations and Their Effect on Measurement Results. Bernie McDermott. May 2010
TN 201005 Vector Network Analyzer Calibrations and Their Effect on Measurement Results May 2010 Bernie McDermott Lead Metrologist Calibration Products and Services Measurement Examples and Technical Notes
More informationHigh Speed Characterization Report. DVI-29-x-x-x-xx Mated With DVI Cable
High Speed Characterization Report DVI-29-x-x-x-xx Mated With DVI Cable REVISION DATE: 07-18-2004 TABLE OF CONTENTS Introduction... 1 Product Description... 1 Overview... 2 Results Summary... 3 Time Domain
More informationAgilent PNA Series Microwave Network Analyzers
Agilent PNA Series Microwave Network Analyzers Configuration Guide PNA-L N5230A PNA-L N5230A PNA-X N5242A PNA E8362B PNA E8363B PNA E8364B PNA E8361A PNA N5250A 300 khz to 6, 13.5, or 20 GHz 10 MHz to
More informationSPICE Model Validation Report
EQCD (DV to DV) Cable Assembly Mated with: QTE-xxx-01-x-D-A QSE-xxx-01-x-D-A Description: Cable Assembly, High Data Rate, 0.8mm Pitch Samtec, Inc. 2005 All Rights Reserved TABLE OF CONTENTS INTRODUCTION...
More informationLecture 10. Vector Network Analyzers and Signal Flow Graphs
HP8510 Lecture 10 Vector Network Analyzers and Signal Flow Graphs Sections: 6.7 and 6.11 Homework: From Section 6.13 Exercises: 4, 5, 6, 7, 9, 10, 22 Acknowledgement: Some diagrams and photos are from
More informationAgilent Digital Measurement Forum
Agilent Digital Measurement Forum HMDI 1.3 Agilent Solution Overview Media Agilent HDMI Solution Solution Overview Solution Specifics Agilent Total Solutions Test Point Access Assemblies (TPAs) Source
More informationMarch 4-7, 2018 Hilton Phoenix / Mesa Hotel Mesa, Arizona Archive
March 4-7, 2018 Hilton Phoenix / Mesa Hotel Mesa, Arizona Archive 2018 BiTS Workshop Image: pilgrims49 / istock COPYRIGHT NOTICE The presentation(s)/poster(s) in this publication comprise the Proceedings
More informationE2655C Probe Deskew and Performance Verification Kit
Keysight E2655C Probe Deskew and Performance Verification Kit User s Guide Calibration for the Solder-in and Socketed Probe Heads 3 Calibration for Hand-held Browser Probe Heads 10 Calibrating the InfiniiMax
More informationAgilent PNA Series Microwave Network Analyzers
Agilent PNA Series Microwave Network Analyzers Configuration Guide PNA-L N5230A PNA-L N5230A PNA E8362B PNA E8363B PNA E8364B PNA E8361A PNA N5250A 300 khz to 6, 13.5, or 20 GHz 10 MHz to 20, 40, or 50
More informationAgilent Technologies S-Parameter and TDR Impedance Measurement Solution Summary
Agilent Technologies S-Parameter and TDR Impedance Measurement Solution Summary Built-in S-parameter testing Easy and accurate transmission channel/media characterization Transmission lines for high speed
More informationFindings on MDI Return Loss Measurement GITESH BHAGWAT SANTA BARBARA DESIGN CENTER
Findings on MDI Return Loss Measurement GITESH BHAGWAT SANTA BARBARA DESIGN CENTER 1 Supporters Eric DiBiaso (TE Connectivity) Bin Lin (TE Connectivity) Kurt Smith (Coilcraft) 2 Presentation Outline MDI
More informationA simple method to characterize and accurately remove the effects of push-on connectors. O.J. Danzy Application Engineer
A simple method to characterize and accurately remove the effects of push-on connectors. O.J. Danzy Application Engineer Original Authors Robert Schaefer, Keysight Technologies, Inc. Reiner Oppelt, Rosenberger
More informationSPECIFICATION AND PERFORMANCE CHARACTERISTICS OF DVI MALE AND FEMALE CONNECTOR SERIES
SPECIFICATION AND PERFORMANCE CHARACTERISTICS OF DVI MALE AND FEMALE CONNECTOR SERIES CIRCUIT ASSEMBLY CORP. 18 THOMAS STREET, IRVINE, CA 92618-2777 Page No. 1 CONTENTS CLAUSE PAGE 1.0 SCOPE.. 3 2.0 APPLICABLE
More informationEvaluates: MAX MAX14970 Evaluation Kit. General Description. Quick Start (Application Circuit) Features. Table 1. Default Shunt Positions
General Description The MAX14970 evaluation kit (EV kit) provides a proven design to evaluate the MAX14970 dual-channel buffer. The EV kit contains four sections: an application circuit, characterization
More informationKeysight Technologies PNA Series Microwave Network Analyzers
Keysight Technologies PNA Series Microwave Network Analyzers Configuration Guide PNA-L N5230A PNA-L N5230A PNA-X N5242A PNA E8362B PNA E8363B PNA E8364B PNA E8361A PNA N5250A 300 khz to 6, 13.5, or 20
More informationAgenda TDR Measurements Using Real World Products
Agenda TDR Measurements Using Real World Products The Case for using both TDR and S-parameters Device Package Analysis - Measure Impedance -C-self Characterizing Device Evaluation Test board Measure Differential
More informationApplication Note FOR SMA Calibration Kit for VNA. LCAL06A A female calibration kit and used for DC ~ 6.0 GHz VNA test cable with male end connector.
Application Note FOR SMA Calibration Kit for VNA LCAL06A, LCAL06B, LCAL06C and LCAL09A are precision SMA calibration kits which provide accurate and reliable Short-Open-Load-Thru (SOLT) or Load-Reflect-Match
More informationIEEE-488. included No. Yes, 1 per IEEE-488. included. channel. Yes, 1 per IEEE-488. included. channel IEEE-488. included. channel IEEE-488.
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Section 5 8/6/04 4:36 PM Page 5-8 Table 5-2: High Speed Power Supplies Model 2302 2303 2303-PJ 2304A 2306 2306-PJ 2306-VS
More informationUFS Test Fixtures. User Manual. Document Number: n/a Version: February 21, 2018
UFS Test Fixtures User Manual Document Number: n/a Version: February 21, 2018 This document describes Astek s UFS Test Fixture product family. To receive product literature, visit us at http://www.astekcorp.com.
More informationN1014A SFF-8431 (SFP+)
DATA SHEET N1014A SFF-8431 (SFP+) Compliance and Debug Application for 86100D DCA-X and N109X DCA-M Oscilloscopes Be Confident With Compliant Measurements Easy-to-use oscilloscope application that lets
More informationOpen NAND Flash Interface Specification: NAND Connector
Open NAND Flash Interface Specification: NAND Connector Connector Revision 1.0 23-April-2008 Hynix Semiconductor Intel Corporation Micron Technology, Inc. Phison Electronics Corp. Sony Corporation Spansion
More informationConnectors, adapters, and tools
Model Name Use With: 213-CON Rear Panel Mating Connector 2200-20-5, 2200-30-5, 2200-32-3, 2200-60-2, 2200-72-1 237-BAN-3A Triax to Banana Plug 4200-SCS, 7072, 7072-HV, DMMs 237-BNC-TRX 237-TRX-BAR 237-TRX-NG
More informationKeysight Technologies On-Wafer Testing of Opto-Electronic Components Using the Lightwave Component Analyzers. Application Note
Keysight Technologies On-Wafer Testing of Opto-Electronic Components Using the Lightwave Component Analyzers Application Note Introduction When measurements of optoelectronic components are performed on
More informationMAX4951C Evaluation Kit Evaluates: MAX4951C
19-5944; Rev 0; 6/11 MAX4951C Evaluation Kit General Description The MAX4951C evaluation kit (EV kit) provides a proven design to evaluate the MAX4951C dual-channel buffer. The EV kit contains four sections:
More informationAXOMACH E-16. High data rate links for faster data transmission. Microwave coaxial cables. Panel mount connector QUASI-FLEX. Cable mount connector 2
AXOMACH High data rate links for faster data transmission AXON proposes AXOMACH, a range of high data rate links composed of low loss microwave coaxial cables and different connector types: AXOMACH Micro-D
More informationInfiniBand Trade Association
InfiniBand Trade Association Revision 1.06 4/11/2017 IBTA VNA MOI for FDR and EDR Cable Tests This material is provided for reference only. The InfiniBand Trade Association does not endorse the vendors
More informationProposal for SAS 2.x Specification to Enable Support for Active Cables
08-052r2 Proposal for SAS 2.x Specification to Enable Support for Active Cables Gourgen Oganessyan QUELLAN March 7, 2008 Introduction Inclusion of active cable interconnect option into the SAS specification
More information802.3cb PMD and Channel. Anthony Calbone 3/14/2016
802.3cb PMD and Channel Anthony Calbone 3/14/2016 Overview The presentation introduces a single link segment for each 2.5 Gb/s and 5 Gb/s for 802.3cb This link segment is described for two different reference
More informationAV2040X Series Electronic Calibration Module
AV2040X Series Electronic Calibration Module Product Overview: AV2040X series electronic calibration module includes 5 models of AV20402/AV20403/ AV20404/AV20405/AV20409, covering the frequency ranges
More informationSAS-2 Internal Channel Modeling (05-276r0) Barry Olawsky Hewlett Packard r0 SAS-2 Channel Modeling 1
SAS-2 Internal Channel Modeling (05-276r0) Barry Olawsky Hewlett Packard 05-276r0 SAS-2 Channel Modeling 1 Project Goals Provide industry with data to better understand customer (hp and other OEMs) applications.
More informationUsing ADS to Post Process Simulated and Measured Models. Presented by Leon Wu March 19, 2012
Using ADS to Post Process Simulated and Measured Models Presented by Leon Wu March 19, 2012 Presentation Outline Connector Models From Simulation Connector Models From Measurement The Post processing,
More informationMDI for 4x25G Copper and Fiber Optic IO. Quadra (CFP4 proposal) Connector System
MDI for 4x25G Copper and Fiber Optic IO Quadra (CFP4 proposal) Connector System Nov 7, 2011 Nathan Tracy, TE Connectivity Tom Palkert, Molex 4x25Gb/s MDI Potential Requirements Critical Needs: Excellent
More informationAgilent. E5092A Configurable Multiport Test Set. Configuration Guide
Agilent E5071C Network Analyzer 9 khz to 4.5 GHz 100 khz to 4.5 GHz (with bias tees) 9 khz to 8.5 GHz 100 khz to 8.5 GHz (with bias tees) 300 khz to 20 GHz (with bias tees) E5092A Configurable Multiport
More informationAutomotive Ethernet BroadR-Reach
Automotive Ethernet BroadR-Reach Agilent PHY Compliance Solutions 1 Last update 2013/07/25 (YS) Agenda BroadR-Reach Overview Transmitter Testing Link Segment Testing 2 BroadR-Reach Applications 3 Connectivity
More informationS Application Circuit with SATA Input/Output S Eye Diagram Test Circuit with SMA Inputs/ Outputs
19-4953; Rev 0; 9/09 MAX4951AE Evaluation Kit General Description The MAX4951AE evaluation kit (EV kit) provides a proven design to evaluate the MAX4951AE dual-channel buffer. The EV kit contains four
More informationPCIEC PCI Express Jumper High Speed Designs in PCI Express Applications Generation GT/s
PCIEC PCI Express Jumper High Speed Designs in PCI Express Applications Generation 3-8.0 GT/s Mated with PCIE-RA Series PCB Connectors Copyrights and Trademarks Copyright 2015, Inc. COPYRIGHTS, TRADEMARKS,
More informationMAX14972 Evaluation Kit Evaluates: MAX14972
19-6165; Rev 0; 12/11 MAX14972 Evaluation Kit General Description The MAX14972 evaluation kit (EV kit) provides a proven design to evaluate the MAX14972 dual SuperSpeed USB 3.0 equalizer/redriver utilizing
More informationAgilent E5072A ENA Series Network Analyzer
Agilent E5072A ENA Series Network Analyzer 30 khz to 4.5 /8.5 GHz Configuration Guide Ordering Guide The following steps will guide you through configuring your E5072A. 1-year return to Agilent service
More informationPDS: Rev :A STATUS:Released Printed: Jan 04, 2012
of 2 A.0 Objective This specification defines the performance, test, quality and reliability requirements of the USB3.0 Standard- A Receptacle. 2.0 Scope This specification is applicable to the termination
More informationOSFP Connector Cage & Cable System
PAGE /6 /5/7 UNRESTRICTED OSFP Connector Cage & Cable System PAGE /6 /5/7 UNRESTRICTED.0 SCOPE This Product Specification covers performance, test and quality requirements for the JPC Quad Small Form Factor
More informationADS USB 3.1 Compliance Test Bench
ADS 2016.01 USB 3.1 Compliance Test Bench Notices Keysight Technologies, Inc. 1983-2016 1400 Fountaingrove Pkwy., Santa Rosa, CA 95403-1738, United States All rights reserved. No part of this documentation
More informationAgilent. E5071C Network Analyzer 9 khz to 4.5/6.5/8.5 GHz 100 khz to 4.5/6.5/8.5 GHz (with bias tees) 300 khz to 14/20 GHz (with bias tees)
Agilent E5071C Network Analyzer 9 khz to 4.5/6.5/8.5 GHz 100 khz to 4.5/6.5/8.5 GHz (with bias tees) 300 khz to 14/20 GHz (with bias tees) E5092A Configurable Multiport Test Set Configuration Guide This
More informationEvaluates: MAX2851. MAX2851 Evaluation Kit. General Description. Features. Quick Start. Connections and Setup. Test Equipment Required
MAX2851 Evaluation Kit Evaluates: MAX2851 General Description The MAX2851 evaluation kit (EV kit) simplifies testing of the MAX2851 receive and transmit performance in 802.11a applications operating in
More informationReference Guide. Agilent Technologies Electronic Calibration Modules. RF Two-Port 85091C 85092C 85093C 85096C 85098C 85099C. RF Four-Port N4431B
Reference Guide Agilent Technologies Electronic Calibration Modules RF Two-Port 8509C 85092C 85093C 85096C 85098C 85099C RF Four-Port N443B Microwave Two-Port N4690B N469B N4692A N4693A N4694A N4696B Microwave
More informationAgilent ENA RF Network Analyzer
Agilent ENA RF Network Analyzer Configuration Guide E5071C E5091A 9 khz to 4.5 GHz 100 khz to 4.5 GHz (with bias tees) 9 khz to 8.5 GHz 100 khz to 8.5 GHz (with bias tees) Multiport test set This configuration
More informationE5092A Configurable Multiport Test Set
Keysight Technologies E5080A Network Analyzer 9 khz to 4.5/6.5/9 GHz E5092A Configurable Multiport Test Set Configuration Guide 02 Keysight 5080A Network Analyzer & E5092A Configurable Multiport Test Set
More informationDensiShield Cable Assembly. InfiniBand Standard CX4 Standard
DensiShield Cable Assembly InfiniBand Standard CX4 Standard SI-2008-06-001 Revision 1 August-21-2008 Introduction The purpose of these tests was to show compliance of FCI s 26 AWG DensiShield cable assemblies
More informationHigh Speed and High Power Connector Design
High Speed and High Power Connector Design Taiwan User Conference 2014 Introduction High speed connector: Electrically small Using differential signaling Data rate >100Mbps High power connector: Static
More informationApplication Note. PCIE-RA Series Final Inch Designs in PCI Express Applications Generation GT/s
PCIE-RA Series Final Inch Designs in PCI Express Applications Generation 3-8.0 GT/s Copyrights and Trademarks Copyright 2012, Inc. COPYRIGHTS, TRADEMARKS, and PATENTS Final Inch is a trademark of, Inc.
More informationKeysight Technologies N5394A DVI Electrical Performance Validation and Compliance Software for Infiniium Oscilloscopes. Data Sheet
Keysight Technologies N5394A DVI Electrical Performance Validation and Compliance Software for Infiniium Oscilloscopes Data Sheet 02 Keysight N5394A DVI Electrical Performance Validation and Compliance
More informationAdapter characterization up to 110 GHz
Adapter characterization up to 110 GHz EMRP HF Circuits project: 6 th European ANAMET meeting 28.06.2016 Adapter characterization: Motivation The challenges of an adapter characterization: Sheet Series
More informationPXI Vector Network Analyzer
CONFIGURATION GUIDE PXI Vector Network Analyzer M9370A 300 khz to 4 GHz M9371A 300 khz to 6.5 GHz M9372A 300 khz to 9 GHz M9373A 300 khz to 14 GHz M9374A 300 khz to 20 GHz M9375A 300 khz to 26.5 GHz Drive
More informationDirect Connection of OML Frequency Extenders to Keysight s PNA-C (E836xC) VNA for 1-Path 2-Port S-Parameter Measurements
Direct Connection of OML Frequency Extenders to Keysight s PNA-C (E836xC) VNA for 1-Path 2-Port S-Parameter Measurements Introduction For full two-port S-parameter measurements to extend PNA-C vector network
More informationApplication Note. PCIE-EM Series Final Inch Designs in PCI Express Applications Generation GT/s
PCIE-EM Series Final Inch Designs in PCI Express Applications Generation 3-8.0 GT/s Copyrights and Trademarks Copyright 2015, Inc. COPYRIGHTS, TRADEMARKS, and PATENTS Final Inch is a trademark of, Inc.
More informationDisplayPort Testing Challenges
DisplayPort Testing Challenges U N Vasudev May 6 th 2013 Agenda DisplayPort Overview DisplayPort 1.2 updates DisplayPort 1.2 Transmitter Testing What s New: T2, TP3, TP3EQ Physical Layer Test Overview
More informationKeysight Technologies E5080A ENA Vector Network Analyzer. E5092A Configurable Multiport Test Set
Keysight Technologies E5080A ENA Vector Network Analyzer 9 khz to 4.5/6.5/9 GHz E5092A Configurable Multiport Test Set Configuration Guide 02 Keysight E5080A ENA Vector Network Analyzer & E5092A Configurable
More informationKeysight Technologies E5080A ENA Vector Network Analyzer. E5092A Configurable Multiport Test Set
Keysight Technologies E5080A ENA Vector Network Analyzer 9 khz to 4.5/6.5/9 GHz E5092A Configurable Multiport Test Set Configuration Guide 02 Keysight E5080A ENA Vector Network Analyzer & E5092A Configurable
More informationS Proven PCB Layout S Fully Assembled and Tested. Maxim Integrated Products 1
19-5059; Rev 1; 4/10 General Description The MAX4951B evaluation kit (EV kit) provides a proven design to evaluate the MAX4951BE dual-channel redriver. The EV kit contains four sections: application circuit,
More informationOver 5,000 products High Performance Adapters and Sockets Many Custom Designs Engineering Electrical and Mechanical ISO9001:2008 Registration
Overview Company Overview Over 5,000 products High Performance Adapters and Sockets Many Custom Designs Engineering Electrical and Mechanical ISO9001:2008 Registration Adapter Technology Overview Pluggable
More informationTektronix Innovation Forum
Tektronix Innovation Forum Enabling Innovation in the Digital Age DisplayPort 1.2 Spec Updates and overview of Physical layer conformance testing Presenter: John Calvin DisplayPort 1.2 Spec Updates Agenda
More informationAdapter Technologies
Adapter Technologies Toll Free: (800) 404-0204 U.S. Only Tel: (952) 229-8200 Fax: (952) 229-8201 email: info@ironwoodelectronics.com Introduction Company Overview Over 5,000 products High Performance Adapters
More informationAmphenol Amphenol Taiwan Corporation Sheet 1 of 16
Amphenol Amphenol Taiwan Corporation Sheet 1 of 16 Title: USB3.0 Product Specification Part Number: GSB3 Series Description: USB3.0 A&B Type Plug & Receptacle Revisions Control Rev. ECN Number Originator
More informationType-C Technologies and Solutions
Type-C Technologies and Solutions 2016.12.20 Gary Hsiao Project Manager Gary_Hsiao@keysight.com Agenda Type-C Overview Type-C PD Solutions USB 3.1 Simulation Solutions USB 3.1 TX/RX Solutions USB 3.1 Cable/Connector
More informationN5416A USB Demo Guide
Demo Guide This N5416A Demo Guide consists of : A single slide demo description followed by : Step 1 - instructions on how to connect all the equipment Step 2 - instructions on the configuration of the
More informationREFERENCE DESIGN Quad-SFP Host Adapter
Reference Design: HFRD-32.0 Rev. 2; 11/08 REFERENCE DESIGN Quad-SFP Host Adapter AVAILABLE Quad-SFP Host Adapter Table of Contents 1 Overview...2 2 Obtaining Additional Information...2 3 Typical Use...3
More informationA Modular Platform for Accurate Multi- Gigabit Serial Channel Validation
A Modular Platform for Accurate Multi- Gigabit Serial Channel Validation Presenter: Andrew Byers Ansoft Corporation High Performance Electronics: Technical Challenges Faster data rates in increasingly
More information7011-C, 7012-C, 7013-C, 7015-C, 7018-C, 7021, MTC-2 Mass Terminated Assembly Twisted pair (45) 96-pin female 96-pin female 2 6.
TERMINATIONS LENGTH MODEL DESCRIPTION TYPE FROM TO m ft USE WITH: 236-ILC-3 Safety Interlock Shielded twisted pair 3-pin round 3-pin round 3 10 236, 237, 238, 8007, 8008 237-ALG-2 Low Noise Input Triax
More information1.4 mm Pitch High Frequency Differential, Coaxial PCB Probe (40 GHz)
D-COAX, Inc. Differential/Single-ended High Frequency Probe 1.4 mm Pitch High Frequency Differential, Coaxial PCB Probe (40 GHz) The DP1.4 Differential probe by D-COAX is used for high frequency PCB differential
More informationKeysight E6964A Automotive Ethernet MDI S-parameter Compliance Solution
Keysight E6964A Automotive Ethernet MDI S-parameter Compliance Solution Medium Dependent Interface (MDI) S-parameter testing made more accurate for components being tested for 100BASE-T1 or BroadR-Reach
More informationSEAM-RA/SEAF-RA Series Final Inch Designs in PCI Express Applications Generation GT/s
SEAM-RA/SEAF-RA Series Final Inch Designs in PCI Express Applications Generation 3-8.0 GT/s Copyrights and Trademarks Copyright 2011 Samtec, Inc. Developed in conjunction with Teraspeed Consulting Group
More informationKeysight N9030A Signal Analyzer Option BBA Analog Baseband IQ Inputs Retrofit Kit
Keysight N9030A Signal Analyzer Option BBA Analog Baseband IQ Inputs Retrofit Kit Notice: This document contains references to Agilent. Please note that Agilent s Test and Measurement business has become
More information11525A 11524A
8 Typical Configuration 11900A 11901A 11904A 8059A 1250-1159 1250-1748 85058-60007 11900C 11901C 11901D 11904C 11904D 8059C 1250-1462 85058-60009 1190A 1250-166 1250-174 11525A 11524A 11852B 11852B Option
More informationMAX4899AE Evaluation Kit. Evaluates: MAX4899AE/MAX4899E
19-4025; Rev 0; 1/08 General Description The MAX4899AE evaluation kit (EV kit) provides a proven design to evaluate the MAX4899AE USB 2.0 high-speed, fault-tolerant 4:1 multiplexer. The EV kit routes a
More informationSAS-2 Zero-Length Test Load Characterization (07-013r7) Barry Olawsky Hewlett Packard (8/2/2007)
SAS-2 Zero-Length Test Load Characterization (07-013r7) Barry Olawsky Hewlett Packard (8/2/2007) 07-013r7 SAS-2 Zero-Length Test Load Characterization 1 Zero-Length Test Load Provides ideal connection
More informationAdvances in Measurement Based Transient Simulation
Time Domain Simulation in ADS, Slide - 1 Advances in Measurement Based Transient Simulation Presented by GigaTest Labs Gary Otonari and Orlando Bell March, 2008 1 Time Domain Simulation in ADS, Slide -
More informationDesignCon 2005 Track 5: Chip and Board Interconnect Design (5-TA2)
DesignCon 2005 Track 5: Chip and Board Interconnect Design (5-TA2) Connector-Less Probing: Electrical and Mechanical Advantages Authors/Presenters: Brock LaMeres, Agilent Technologies Brent Holcombe, Agilent
More informationUSB2.0 Type-C & Regular USB Device Electrical Compliance test procedure
P a g e 1 USB2.0 Type-C & Regular USB Device Electrical Compliance test procedure Version 0.85-27 July 2017 P a g e 2 Contents 1. Reference... 3 2. Background... 3 3. Required equipment and software...
More informationConfiguring a Precision System for On-Wafer Capacitance
Application Note Innovating Test Technologies Configuring a Precision System for On-Wafer Capacitance Development of new aggressively scaled MOS processes and devices depends on high accuracy CV measurements.
More informationField Service Procedure Replacement 400MHz Modem Kit
1. Brief Summary: Troubleshooting document for diagnosing a communications a fault with and replacing the 400MHz modems. 2. Checklist: Verify LED Status Query Modem Signal Strengths Troubleshoot Communications
More information5 Performance Verification
5 Performance Verification Performance Verification TEST EQUIPMENT REQUIRED This procedure can be used to verify the warranted characteristics of the CP015 Current Probe. The recommended calibration interval
More informationJune 6 to 9, 2010 San Diego, CA Probe Cards with Modular Integrated Switching Matrices
June 6 to 9, 2010 San Diego, CA Probe Cards with Modular Integrated Switching Matrices Authors: Evan Grund Jay Thomas Agenda Review of Traditional Scribeline Parametric IV and CV Probe Card Requirements
More informationDesign Test Deploy
Design Test Deploy 9-22-10 www.meritec.com 0142835 Table of Contents Overview2 Housing4-7 Hardware8-10 Wafers11-13 Wafer-Wafer Cables14-18 Wafer-I/O19-21 The 3 Dimensions of 22-25 Off-the-Shelf Product
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationKeysight Technologies E5071C Network Analyzer
Keysight Technologies E5071C Network Analyzer 9 khz to 4.5/6.5/8.5 GHz 100 khz to 4.5/6.5/8.5 GHz (with bias tees) 300 khz to 14/20 GHz (with bias tees) E5092A Configurable Multiport Test Set Configuration
More informationRiseUp RU8-DP-DV Series 19mm Stack Height Final Inch Designs in PCI Express Applications. Revision Date: March 18, 2005
RiseUp RU8-DP-DV Series 19mm Stack Height Final Inch Designs in PCI Express Applications Revision Date: March 18, 2005 Copyrights and Trademarks Copyright 2005 Samtec, Inc. Developed in conjunction with
More informationDesign Test Deploy
Design Test Deploy 9-22-10 www.meritec.com 0142835 Table of Contents Overview2 Housing4-7 Hardware8-10 Wafers11-13 Wafer-Wafer Cables14-18 Wafer-I/O19-21 The 3 Dimensions of 22-25 Off-the-Shelf Product
More informationAgilent E5061B Network Analyzer. Configuration Guide
Agilent E5061B Network Analyzer Configuration Guide Ordering guide The following steps will guide you through configuring your E5061B. Standard furnished item Description Installation guide CD ROM IO libraries
More information