SERVICE MANUAL. 17 LCD Monitor LAW982-1

Transcription

1 SERVICE MANUAL 17 LCD Monitor LAW982-1 THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR CHAES, ERRORS OR OMISSIONS. 1

2 Table of Content Revision List Monitor Specifications LCD Monitor Description Operating Instructions General Instructions Control Buttons Adjusting the Picture Input/Output Specification Input Signal Connector Factory Preset Display Modes Electrical Specifications Panel Specification Panel Feature Optical Characteristics Block Diagram Monitor Exploded View Software Flow Chart Electrical Block Diagram Main Board Inverter/Power Board Schematic Main Board Adapter Board Inverter Board PCB Layout Main Board Inverter Board Adapter Board Maintainability Equipments and Tools Requirement Trouble Shooting Main Board Inverter/Power Board Keypad Board White-Balance, Luminance adjustment EDID Data BOM List

3 Revision List Revision Date Revision History TPV Model Name A01 Feb Initial Release T980KM2NDATHN 3

4 1. Monitor Specifications 4

5 2. LCD Monitor Description The LCD monitor will contain a main board, an inverter/power board and a keypad board which houses the flat panel control logic, brightness control logic and DDC. The Inverter board will drive the backlight of panel and DC-DC conversion. The Adaptor will provide DC-power to Inverter/Power board. 5

6 3 Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located by the side of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. - The power cord should be connected. - Connect the video cable from the monitor to the video card. - Press the power button to turn on the monitor, the power indicator will light up. 3.2 Control Buttons 1. D-sub/DVI Input Source Selection 5. MENU / ENTER 2. Auto Config / Exit 6. Power Button 3. / Contrast 7. Power Indicator 4. / Brightness Power Button Press this button to switch ON/OFF of monitor s power. Power Indicator: Blue Power On mode. Amber Off mode. MENU / ENTER: Active OSD menu or function adjust confirm. Contrast : Adjust contrast or function adjust. Brightness : Adjust brightness or function adjust. D-sub/DVI Input Source Selection Auto Adjust button / Exit: 1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2. When OSD menu is in off status, press this button to activate the Auto Adjustment function. The Auto Adjustment function is used to optimize the Horizontal Position, Vertical Position, Clock and Focus. 6

7 3.3 Adjusting the Picture Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Contrast Contrast from Digital-register. Luminance Brightness Backlight Adjustment Focus Adjust Picture Phase to reduce Horizontal-Line noise Image Setup Clock Adjust picture Clock to reduce Vertical-Line noise. Image Position H. Position Adjust the horizontal position of the picture. V. Position Adjust the verticalposition of the picture. Warm N/A Recall Warm Color Temperature from EEPROM. Cool N/A Recall Cool Color Temperature from EEPROM. Color Temp. User / Red User / Green Red Gain from Digital-register. Green Gain Digital-register. User / Blue Blue Gain from Digital-register. Input Select Analog N/A Select input signal from analog source (D-Sub) Digital N/A Select input signal from digital source (DVI) H. Position Adjust the horizontal position of the OSD. OSD Setup V. Position Adjust the vertical position of the OSD. OSD Timeout Adjust the OSD timeout. 7

8 Language Language N/A Set OSD language. Information Information N/A Show the resolution, H/V frequency and input port of current input timing. Clear each old status of Auto-configuration and set the Yes N/A Reset color temperature to Cool. No N/A Do not execute reset, return to main menu. Exit N/A N/A Exit OSD 8

9 4. Input/Output Specification 4.1 Input Signal Connector 9

10 4.2 Factory Preset Display Modes: Standard Resolution Horizontal Frequency Vertical Frequency Dos-Mode khz 70.0hz VGA SVGA khz 60.0hz khz 75.0hz khz 60.0hz khz 75.0hz khz 60.0hz XGA khz 70.0hz khz 75.0hz khz 60.0hz SXGA khz 75.0hz Note: The factory preset mode for DOS is khz 60.0hz 10

11 4.3 Electrical Specifications 11

12 4.4 Panel Specification A190A1 is a 19.0 wide TFT Liquid Crystal Display monitor with 5pcs U-type CCFL direct type Backlight unit. This monitor supports 1440 x 900 WXGA+ mode and can display 16.2M colors Panel Feature 19 wide WXGA+ TFT LCD Panel MVA Mode Liquid Crystal D-SUB/ DVI-D Input Audio Function Support to 75Hz Refresh Rate Support VESA-DCC 2B plug & play function Support VESA-DPMS & DVI DMPM Power Management Function Super Wide Viewing Angle High Brightness & Contrast Ratio High Brightness & Contrast Angular Dependent Fast LC Response Time Light Weight 12

13 4.4.2 Optical Characteristics 13

14 5. Block Diagram 5.1 Monitor Exploded View 14

15 5.2 Software Flow Chart 1 2 Y 3 N 4 5 N Y 6 7 Y N Y N 11 N N Y Y N 16 Y N 19 Y 15

16 1) MCU initializes. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode. 9) Save the power key status into EPROM. Turn on the LED and set it to green color. Scalar initializes. 10) In standby mode? 11) Update the lifetime of back light. 12) Check the analog port, are there any signals coming? 13) Does the scalar send out an interrupt request? 14) Wake up the scalar. 15) Are there any signals coming from analog port? 16) Display "No connection Check Signal Cable" message. And go into standby mode after the message disappears. 17) Program the scalar to be able to show the coming mode. 18) Process the OSD display. 19) Read the keyboard. Is the power key pressed? 16

17 5.3 Electrical Block Diagram Main Board LCD Interface (CN503) MCU MTV512 (U601) Scalar IC TSU56AK (Include ADC, OSD) (U401) EPR_SDA EPR_SCL H sync D_H sync EEPROM Key Board V sync D_V sync AT24C16N Control RGB D_RGB (U602) Crystal MHZ (X401) D-Sub Connector (CN301) DVI-I only Connector (CN302) DB15_SDA, DDC2_SDA, DB15_SCL DDC2_SCL EEPROM EEPROM 24C02 24C02 (U301) (U302) 17

18 5.3.2 Inverter/Power Board AC input EMI filter Bridge Rectifier and Filter Transformer Rectifier diode 12V Start Circuit: R903 R904 CN102 PWM Control IC Over Voltage Protect Feedback Circuit 12V ON/OFF Lamp OSC and Output Circuit DC Convert Circuit MOSFET Q203/Q204 PWM Feedback Circuit Over Voltage Protect PWM Control IC ON/OFF Control DIM 18

19 6. Schematic 6.1 Main Board 19

20 20

21 21

22 22

23 23

24 24

25 6.2 Adapter Board 25

26 6.3 Inverter Board 26

27 27

28

29 7. PCB Layout 7.1 Main Board 29

30 7.2 Inverter Board 30

31 7.3 Adapter Board 31

32 8. Maintainability 8.1 Equipments and Tools Requirement 1. Voltmeter. 2. Oscilloscope. 3. Pattern Generator. 4. DDC Tool with an IBM Compatible Computer. 5. Alignment Tool. 6. LCD Color Analyzer. 7. Service Manual. 8. User Manual. 32

33 8.2 Trouble Shooting Main Board 1. No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of is normal OK Measure U201 PIN2=1.8V U202 PIN2=3.3V Reinsert or check the Adapter/Inverter section OK Check CN201 or replace U201, U202 X601 and X401 oscillate waveforms are normal OK Replace X601, X401 Replace U601 Replace U401 33

34 No picture (LED orange) No picture The button if under control X601 oscillate waveform is normal Replace X601 OK OK Measure U201 PIN2=1.8V Check reset circuit of U601 is normal Check Correspondent component U202 PIN2=3.3V OK OK Replace U201, U202 Replace U601 X401 oscillate waveform is normal OK Replace X401 Check HS/VS from CN301is Replace normal U401 OK Check Correspondent component Replace U401 34

35 White screen White screen Measure Q204 base is high level? OK X601 oscillate waveform is normal OK Replace X601 Check Q204, Q203 are broken or CN503 solder? Check reset circuit of U601 is normal OK Check Correspondent component. OK Check Correspondent component. Replace PANEL Replace U601 35

36 8.2.2 Inverter/Power Board 2.) W / LED, No Backlight Check CN102 pin5=12v Check adapter or Main Board OK Check ON/OFF signal OK Check Main Board Check U201 pin9=12v OK Change Q201 or Q202 Check U201 PIN1 have the output of square wave at short time OK Change U201 Check D203 (-)/ D204 (-) have the output of square wave at short time. OK Check Q203/Q205/Q207/ D203 Check Q204/Q206/Q208/ D204 Check the resonant wave of pin2 & pin5 for PT201/PT202 OK Check Q209/Q210/C213 Check Q211/Q212/C214 Check the output of PT201/PT202 OK Change PT201/PT202 Check connecter & lamp 36

37 8.2.3 Keypad Board OSD is unstable or not working Is Keypad Board connecting normally? N Connect Keypad Board Y Is Button Switch normally? N Replace Button Switch Y Is Keypad Board Normally? Y N Replace Keypad Board Check Main Board 37

38 9. White-Balance, Luminance Adjustment Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment. 1. How to do the Chroma-7120 MEM. Channel setting A. Reference to chroma 7120 user guide B. Use SC key and NEXT key to modify XyY value and use ID key to modify the TEXT description Following is the procedure to do white-balance adjust 2. Setting the color temp. you want A. MEM.CHANNEL 3 (7800 color): 7800 color temp. parameter is x = 296 ±20, y = 311 ±20, Y = 180 cd/m 2, B. MEM.CHANNEL 4 (6500 color): 6500 color temp. parameter is x = 313±20, y = 329 ±20, Y = 180 cd/m 2 3. Enter into factory mode Turn on power, press the MENU button, pull out the power cord, and then plug the power cord. Then the factory OSD will be at the left top of the panel. 4. Bias adjustment: Set the Contrast to 50; Adjust the Brightness to Gain adjustment: Move cursor to -F- and press MENU key A. Adjust C2 (7800) color-temperature 1. Switch the Chroma-7120 to RGB-Mode (with press MODE button) 2. Switch the MEM. Channel to Channel 3 (with up or down arrow on chroma 7120) 3. The LCD-indicator on chroma 7120 will show x = 296 ±20, y = 311 ±20, Y = 180 cd/m 2 4. Adjust the RED of color1 on factory window until chroma 7120 indicator reached the value R= Adjust the GREEN of color1 on factory window until chroma 7120 indicator reached the value G= Adjust the BLUE of color1 on factory window until chroma 7120 indicator reached the value B= Repeat above procedure (item 4,5,6) until chroma 7120 RGB value meet the tolerance =100±2 B. Adjust C1 (6500) color-temperature 1. Switch the chroma-7120 to RGB-Mode (with press MODE button) 2. Switch the MEM.channel to Channel 4(with up or down arrow on chroma 7120) 3. The LCD-indicator on chroma 7120 will show x = 313 ±20, y = 329 ±20, Y = 180 cd/m 2 4. Adjust the RED of color3 on factory window until chroma 7120 indicator reached the value R= Adjust the GREEN of color3 on factory window until chroma 7120 indicator reachedthe value G= Adjust the BLUE of color3 on factory window until chroma 7120 indicator reached the value B= Repeat above procedure (item 4,5,6) until chroma 7120 RGB value meet the tolerance =100±2 C. Turn the Power-button off to quit from factory mode. 38

39 10. EDID Data Analog (D-SUB) Digital (DVI) 39

40 11. BOM List Part No. for TPV Description Quan. Unit 34G6239BQ1 L BEZEL 1 PCS KEPC980KL1 KEY BOARD 1 PCS 5G808D 1 SCREW WASHER 4 PCS 12G RUBBER FOOT 5 PCS 33G6309 QO L CONTROL BUTTON 1 PCS 33G LENS 1 PCS 34G6240 QO L REAR COVER 1 PCS 34G6241 QO L STAND 1 PCS 34G6242 QO L BASE 1 PCS 34G6243 QO L HIE COVER 1 PCS 37G HIE 1 PCS 40G 19E654 3A ID LABEL 1 PCS 40G A S/N LABEL 4 PCS 40G A LABEL 1 PCS 40G A CARTON LABEL 2 PCS 41G900N654 3B MANUAL 1 PCS 44G CUSHION 1 PCS 44G CUSHION 1 PCS 44G A CARTON 1 PCS 44GZ PIEEA BOX 1 PCS 45G RN PE BAG FO MANUAL/BASE 1 PCS 45G PE BAG FOR BASE 1 PCS 45G EPE COVER 1 PCS 45G OUT PE BAG 1 PCS 45G PE BAG FOR MONITOR 1 PCS 50G HANDLE1 1 PCS 50G HANDLE2 1 PCS 52G 1186 SMALL TAPE 8 CM 80L L19 2 AD ADAPTER 1 PCS 89G1738GAA D1 SIGNAL CABLE 1 PCS 89G414A18N IS POWER CORD 1 PCS 89L FFC CABLE 1 PCS M1G SCREW 4 PCS M1G SCREW 4 PCS M1G SCREW 4 PCS Q1G SCREW 2 PCS 750LLM90SA1 CMO 19" PANEL 1 PCS 40