Home Automation, Inc. Model 32A00-5. OmniTouch with Video Touchscreen
|
|
- Jessie Turner
- 5 years ago
- Views:
Transcription
1 Home Automation, Inc. Model 32A00-5 OmniTouch with Video Touchscreen Installation Manual Document Number 32I00-5 Rev A November, 2005
2 PLANNING In selecting a place to mount the touchscreen, be sure to avoid an area where studs, plumbing, or electrical wiring may be located behind the wallboard. It should be mounted so that the display is at or slightly above eye level. The touchscreen requires Cat-5 (4-pair) cable for operation. The Cat-5 cable provides power, communications, and the video signal from the HAI Touchscreen Hub to the touchscreen. Run the Cat-5 cable between the touchscreen and the HAI Touchscreen Hub. The maximum distance between the controller and each touchscreen is 800 feet. Terminate both ends of the Cat-5 cable with an 8-position modular connector (as if to make a standard network cable). INSTALLATION Hold the template (Installation Template 32A10-1) against the wall so the top edge is at the appropriate height and parallel to the floor. Using a Punch, or similar instrument, punch through the center of each tick mark (+) on the template. Drill a 1/4" hole at each punch mark. Using a pencil, draw a line around the quadrant of each hole as shown as shown. Carefully cut along the pencil line. 4" 5 3/8" DO NOT OVERSIZE THIS CUTOUT!
3 Remove the faceplate from the touchscreen by grasping the top and bottom edges of the faceplate and carefully lifting the bottom edge away from touchscreen housing. Insert the 8-position modular cable into the RJ-45 connector (J6) through the rectangular cutout in the touchscreen backbox. Locate the retaining flange screws in the upper left and lower right corners. Turn the screws counterclockwise until the gap between the retaining flange and the housing flange is wider then the wall. WALL
4 Place the assembled unit into the cutout in the wall. Turn the retaining flange screws clockwise until they are snug (do not over tighten). WALL
5 Installing the Faceplate Before installing the faceplate, remove the protective film from the LCD area of the touchscreen. Fasten the faceplate onto the touchscreen by hanging the top of the faceplate on the top edge of the touchscreen, then gently snapping the bottom onto the touchscreen. REMOVING THE TOUCHSCREEN After installation, if it is necessary to remove the touchscreen from the wall, turn retaining flange screws 1 turn counterclockwise. Note: Do not turn the retaining flange screws more than 1 full turn counterclockwise; otherwise the retaining flange may fall off into the wall. CONNECTING TO THE HAI TOUCHSCREEN HUB Each OmniTouch Touchscreen with Video connects to the HAI Touchscreen Hub. The HAI Touchscreen Hub provides power, communications, and the video signal to the touchscreen. Note: HAI Controller Firmware Version 2.11 or later is required to work with the HAI OmniTouch Touchscreen with Video. A maximum combination of 4 touchscreens and consoles can be used with OmniLT, a maximum combination of 8 with Omni II, and a maximum combination of 16 with OmniPro II. Each HAI Touchscreen Hub can support a maximum of 8 touchscreens. Note: When more than 8 OmniTouch Touchscreens with Video are used with an OmniPro II, a second HAI Touchscreen Hub with Video Encoder is required (see HAI Touchscreen Hub Installation Manual for more details). Connections: When connecting the OmniTouch Touchscreen with Video to the HAI Touchscreen Hub, insert the 8-position modular cable, coming from the touchscreen, into one of the RJ-45 connector (J1-J8) on the HAI Touchscreen Hub. See the HAI Touchscreen Hub Installation Manual for complete installation instructions.
6 ADDRESSING THE TOUCHSCREEN OmniTouch with Video touchscreens are connected to the same communications bus as HAI consoles. Each console and touchscreen must have a unique address. The default address setting of the touchscreen is "1". When power is first connected to the touchscreen, if the touchscreen isn t addressed properly (other consoles or touchscreens already occupy the touchscreen address) or isn t communicating with the controller, the following page is displayed. To assign an address to the OmniTouch touchscreen, press and hold the HAI logo for three seconds. The "Touchscreen Address" page is displayed. This page allows the installer to adjust the brightness and contrast of the touchscreen and assign the touchscreen address.
7 Press the [up arrow] button to raise the current setting and the [down arrow] button to lower the current setting. When complete, press the [exit] button in the lower-right corner to save the settings and exit. Once the touchscreen is properly configured and communicating with the controller, other configuration items may be configured using the "Screen Setup" page. To access the "Screen Setup" page, from the Home page, touch the [Setup] icon. See the Touchscreen User s Guide (32R00-5) for additional information on these items. Note: In the event of an AC Power failure and the HAI controller is running on backup battery power, the touchscreen display will be lowered to its lowest viewable setting. Do not try to adjust the brightness and contrast levels. When AC Power is restored, the touchscreen display will automatically return to its correct settings. RESETTING THE TOUCHSCREEN If for any reason the touchscreen needed to be reset, remove the faceplate and press the reset button marked "SW1" on the circuit board below the LED. SPECIFICATIONS Size: Backbox cutout: 5.375" W x 4" H Faceplate: 5.9" W x 4.6"H LCD View Area: 3.26 W x 2.47 H Operating Voltage: 24 VDC Maximum Current Consumption at 24 VDC: 200 ma based on Maximum Cable Length of 800 feet Connect Using: Cat-5 (4-pair) cable Maximum Cable Length: 800 feet
8 FCC NOTICE This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Verified to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. Copyright 2005 Home Automation, Inc. ALL RIGHTS RESERVED
Home Automation, Inc. Model 32A00-1. OmniTouch Touchscreen
Home Automation, Inc. Model 32A00-1 OmniTouch Touchscreen Installation Manual Document Number 32I00-1 Rev A July, 2003 FCC NOTICE This device complies with FCC Rules Part 15. Operation is subject to the
More informationHome Automation, Inc. Model 53A00-1. OmniTouch 5.7 Touchscreen with Video
Home Automation, Inc. Model 53A00-1 OmniTouch 5.7 Touchscreen with Video Installation Manual Document Number 53I00-1 Rev A June, 2007 FCC NOTICE This device complies with FCC Rules Part 15. Operation is
More information7760 LCD Glass Keypad
* * * INSTALLATION GUIDE 7760 LCD Glass Keypad Description The DMP Model 7760 LCD Glass Keypad offers the same functionality and flexible features as standard DMP keypads. The contemporary glass touch
More informationPower Hub Cat. No. 83A00-1. Installation Manual WEB VERSION
Power Hub Cat. No. 83A00-1 Installation Manual WARNINGS AND CAUTIONS Read and understand all instructions. Follow all warnings and instructions marked on the product. Do not use this product near water
More informationATP1000 Touchpad/Display Installation Instructions
ATP1000 Touchpad/Display Installation Instructions Product summary The ATP1000 lets you control all programming and operation of compatible security systems (see the Specifications section). The large
More information2GI. Touch Screen Wireless Keypad
2GI Touch Screen Wireless Keypad For Remote Control of the 2GIG Security System INSTALL INSTRUCTIONS This document describes the basic installation information for the 2GIG TS1 and the steps necessary
More informationInfosystem Remote Touchscreen Installation Instructions
Infosystem Remote Touchscreen Installation Instructions DOC. #569102100 A 7/30/04 PRINTED IN U.S.A. Regulatory Compliance Safety This device has been tested and found to be in compliance with the requirements
More informationBrivo ACS Installation Guide August 2001
DRAFT Brivo ACS Installation Guide August 2001 NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
More informationView Wall Interface. Dynamic Glass INSTALLATION GUIDE. Description. System Requirements. Installation Overview
Description The solution is a compact, wall-mounted interface used for monitoring and changing the tint levels of View Dynamic Glass. The product leverages 802.11-based Wi-Fi technology for connectivity
More informationInstallation Guide DRAFTMF4100
Installation Guide MF4100 This Class B digital apparatus complies with Canadian ICES-003 Cet appareill numérique de la classes B est conform à la norme NMB-003 du Canada This device complies with Part
More informationENTRACOMP 26SA With Remote Open Input. User/Installation Manual
ENTRACOMP 26SA With Remote Open Input User/Installation Manual COPYRIGHT 2001 SOUNDCRAFT INC. PRINTED IN U.S.A. TABLE OF CONTENTS INTRODUCTION... 1 SETTING THE SYSTEM (FACILITY) CODE... 3 PROGRAMMING THE
More informationInstallation Instructions. Product Summary. Installation Guidelines. Tools and Equipment Needed. Table 1. Touchpad Power Usage
Document Number: 466-1759 Rev. B August 2000 6 A I J 5 O I J A 9 A A O B B 0 A ) M = O )!, A = O 5 EA J 2 = C A H * " # $. A = J K H A I 5 O I J A A K + % & ' 5 J = J K I EC D J I * O F = I I, Installation
More informationManual. Network Expansion Port 2 NEP-2. English. Brands by Navico - Leader in Marine Electronics
Manual Network Expansion Port 2 NEP-2 English www.lowrance.com www.simrad-yachting.com Brands by Navico - Leader in Marine Electronics Disclaimer As Navico is continuously improving this product, we retain
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationICS Entrance Management Sign Installation Guide. Version 1.0
ICS Entrance Management Sign Installation Guide Version 1.0 Thank you for purchasing your new ICS Entrance Management System (EMS) from Innovative Control Systems, Inc. Installation Overview This document
More informationWireless Wall Switch Guide
Wireless Wall Switch Guide Battery-Powered Window Coverings Control Like Never Before This guide shows you how to set up and operate Battery-Powered motorized products using the wireless wall switch. The
More informationD1265. Installation Guide. Touchscreen Keypad
D1265 EN Installation Guide Touchscreen Keypad D1265 Installation Guide 1.0 Introduction Contents 1.0 Introduction...3 1.1 Overview...3 1.2 Graphical Buttons...3 1.3 Audible Tones...4 1.4 Supervision...4
More informationZ-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly
Replacing the LCD Cable To remove and replace the LCD Cable you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Socket wrench with 10mm socket Removing the Side Panel 1.
More informationFC-25/50DA Main Circuit Board Replacement Product Installation Document
FC-25/50DA Main Circuit Board Replacement Product Installation Document Document 51875 Rev A 10/12/01 ECN 01-506 This Product Installation Document outlines the replacement of the Main Circuit Board for
More informationHAI Part Numbers and Descriptions March, 2003
OmniLT Controllers 21A00-1 OmniLT Controller OmniLT controller with enclosure, RJ31X jack and cable, manuals, accessory kit. 21A00-2 OmniLT Board Only OmniLT controller board only 21A00-11 OmniLT for Leviton
More informationWireless Area Controller (WAC60)
Installation Instructions The Daintree WAC60 Wireless Area Controller (WAC) is at the heart of the Daintree wireless controls solution for smart buildings. It provides intelligent control across a large
More informationInnoMedia ipbx-400. Quick Install Guide.
InnoMedia ipbx-400 Quick Install Guide www.innomedia.com Table of Contents Introduction 2 Package Contents 2 Installation 3 Wall-Mounting Instructions 5 Troubleshooting 6 Appendix A. LED Status Summary
More information*520886* IntelliTouch Pool & Spa Control System MobileTouch Wireless Controller. User s and Installation Guide. P/N Rev A
pool/spa control system IntelliTouch Pool & Spa Control System MobileTouch Wireless Controller User s and Installation Guide P/N 520886 - Rev A *520886* i MobileTouch Wireless Controller kit contents The
More informationA TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address
Requirements A TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address Power Up A Reader with an Ethernet adaptor installed and the network cable
More informationInstalling the ILC LightSync 4.3 or 7 Touch Screen Station. Rev. B
Installing the ILC LightSync 4.3 or 7 Touch Screen Station Rev. B Overview: The ILC LightSync Touch Screen station (LS-TSS) is available with 4.3 and 7.0 screens. The assembly includes a galvanized NEMA-1
More informationPandora Assembly Instructions With Diamond Systems PC/104 CPUs (Athena, Elektra and Prometheus) November, 2006
Pandora Assembly Instructions With Diamond Systems PC/104 CPUs (Athena, Elektra and Prometheus) November, 2006 Diamond Systems Corp. (650) 810-2500 www.diamondsystems.com This document describes how to
More informationHardware Installation. In this chapter... Custom Labels EMI Noise Filter Installation Mounting DIN Clip Mounting Connections and Wiring
Hardware Installation 2 In this chapter... Custom Labels EMI Noise Filter Installation Mounting DIN Clip Mounting Connections and Wiring Custom Labels Create Custom Labels You may create custom labels
More informationDECOFLEX WIREFREE RTS SWITCH
SOMFY INSTRUCTIONS DECOFLEX WIREFREE RTS SWITCH Part # S 1810897 DecoFlex 1 (white) 1810898 DecoFlex 1 (ivory) 1810899 DecoFlex 1 (black) 1810813 DecoFlex 5 (white) 1810814 DecoFlex 5 (ivory) 1810830 DecoFlex
More informationVoice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document
Voice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document Document 50795 Rev B 10/10/01 ECN 01-507 This Product Installation Document outlines the replacement of the Main
More information4100/ VDC Converter Installation Instructions
4100/4120-0156 8 VDC Converter Installation Instructions Introduction This publication describes the installation procedure for the 8 VDC Converter. Related Documentation Field Wiring Diagram for 4100
More informationMoving-Minds.com Treadmill Desk Operation
LifeSpan Treadmill Desk - Owner s Manual Models DT-5/DT-7 Desk Assembly DT-5 Desk........................................................................................ Assembly Instructions..........................................................................
More informationSuperBus 2000 Phone Interface/Voice Module Installation Instructions
SuperBus 2000 Module Installation Instructions Product summary The SuperBus 2000 (PIV) Module provides phone and voice functions for the Concord, Concord 4, and Concord Express (v4) panels. The PIV module
More informationQuick Start. This document describes how to install the Juniper Networks PTX5000 Packet Transport
PTX5000 Packet Transport Router Quick Start September 2017 Part Number: 530-066788 Revision 01 This document describes how to install the Juniper Networks PTX5000 Packet Transport Router. Contents Quick
More information1101 Universal Transmitter
INSTALLATION SHEET 1101 Universal Description The 1101 is a two input transmitter that is typically used for door/window applications. The 1101 provides two internal magnetic reed switches and an on-board
More informationUser Guide. Version 2.
User Guide Version 2 www.rmepad.com RM epad TM User Guide Please read all instructions carefully before using Please retain these instructions for future reference RM epad TM contains replaceable, rechargeable
More informationLow-Voltage Wallstations Wiring and installation manual Light is OSRAM
www.osram.us/ds Low-Voltage Wallstations Wiring and installation manual Light is OSRAM Overview The Low-voltage Wallstations with integrated LED indicators are available in a range of configurations for
More informationHardware Installation. In this chapter... Custom Labels EMI Noise Filter Installation Mounting DIN Clip Mounting Connections and Wiring
Hardware Installation 2 In this chapter... Custom Labels EMI Noise Filter Installation Mounting DIN Clip Mounting Connections and Wiring Custom Labels Create Custom Labels You may create custom labels
More informationEnvoi Installation and Setup Instructions
Envoi Installation and Setup Instructions DOC. #569068500 F 4/18/05 PRINTED IN U.S.A. Regulatory Compliance Safety This device has been tested and found to be in compliance with the requirements set forth
More informationEMC 10T "CE" Mechanical Upgrade Procedure
EMC 10T "CE" Mechanical Upgrade Procedure Kit Part Number: 009866-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationRevision History E F G H J K Revision Description: K > Allegion Rebranding.
Notes: Enter any notes here. These notes must include: how many sides of the paper are printed ink color (usually black, may also be one or two specific colors, such as a Pantone value, or 17.000 8.500
More informationMODEL 9360-SO SOCCER SCOREBOARD
MODEL 9360-SO SOCCER SCOREBOARD Instruction Manual Address: 34 Main Street, Whitesboro, NY 13492 Phone: 315-736-3967 Toll Free: 800-383-6060 Fax: 315-736-4058 SCOREBOARDS TIMERS MESSAGE SIGNS VIDEO DISPLAYS
More informationPeel/Rewind Upgrade Kit
Peel/Rewind Upgrade Kit Installation Instructions This kit includes the parts and documentation necessary to install the Peel/Rewind upgrade kit on the following printers: ZM400 ZM600 Read these instructions
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Vision OPLC V350-35-R34/V350-J-R34 Installation Guide The Unitronics V350-35-R34/V350-J-R34 offers the following onboard I/Os: 22 Digital Inputs, configurable via wiring to include 2 Analog and 3 HSC/Shaft-encoder
More information2 in 1 LAN Tester and Multimeter Model:
2 in 1 LAN Tester and Multimeter Model: 72-8495 1 IMPORTANT SAFETY INFORMATION Please read these instructions carefully before use and retain for future reference. This instrument is designed and manufactured
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationINSTALLATION INSTRUCTIONS MODEL MRC44KP MRC44 KEYPAD
INSTALLATION INSTRUCTIONS MODEL MRC44KP MRC44 KEYPAD Page 2 Model MRC44KP Model MRC44KP Page 3 TABLE OF CONTENTS Section Title MRC44 Keypad Feature Descriptions...4 Installation MRC44 Keypad Physical Location
More informationInstallation Instructions
Alliance Arming Station AL-1111, AL-1116 1048520C September 2006 Copyright 2006, GE Security Inc. Introduction This is the GE Alliance Arming Station for models AL-1111 (four-line LCD) and AL-1116 (four-line
More informationDC Outdoor Power Supply/Chargers
DC Outdoor Power Supply/Chargers Installation Guide Models Include: WayPoint3 WayPoint7-2.5A @ 12VDC or 24VDC. - 6A @ 12VDC or 24VDC. - 115/230VAC input. - 115VAC input. WayPoint5 WayPoint7V - 4A @ 12VDC
More informationNV-CTP36-V2 Color Touch Screen Installation Guide
NV-CTP36-V2 Color Touch Screen Installation Guide FCC Radio Frequency Interference Statement Warning This equipment has been tested and found to comply with the limits for Class B digital device, pursuant
More informationZodiac FR100 TM INSTALLATION MANUAL
Zodiac FR100 TM INSTALLATION MANUAL June 2014 Table of Contents INTRODUCTION... 3 SPECIFICATIONS... 4 Diodes... 5 Terminal Strips and Cable... 5 READER LAYOUT... 6 READER INSTALLATION... 7 Mounting Plate...
More informationOperation and Maintenance Manual
VM Series Operation and Maintenance Manual VM - Voltage Monitor VM-100-24 V VM-100-48 V VM-100-125 V VM-100-250 V EAGLE EYE POWER SOLUTIONS All Rights Reserved. 1 The Voltage Monitor series reads battery
More informationFujitsu Stylistic ST4000 Series TABLET DOCK USER S GUIDE
Fujitsu Stylistic ST4000 Series TABLET DOCK USER S GUIDE DECLARATION OF CONFORMITY according to FCC Part 15 Responsible Party Name: Fujitsu PC Corporation Address: 5200 Patrick Henry Drive Santa Clara,
More informationPIX 515/515E. PIX 515/515E Product Overview CHAPTER
CHAPTER 4 PIX 515/515E This chapter describes how to install the PIX 515/515E, and includes the following sections: PIX 515/515E Product Overview Installing a PIX 515/515E PIX 515/515E Feature Licenses
More informationUnpacking. Installation
Installation Guide Unpacking Check that the following items are in the box: - One M12 Enclosure containing one or two cameras - One or two VA100 video adapter(s) - One warranty card - One or two BNC-RCA
More informationSuperBus Hardwire Input Module (HIM) Document Number: Rev. C September 1998
SuperBus Hardwire Input Module (HIM) Document Number: 466-1033 Rev. C September 1998 SuperBus Hardwire Input Module for installing a magnetic reed switch* that can provide tamper protection when the switch
More informationDIO-0808RN-USB. N Series for USB Isolated Digital I/O Unit(8ch Relay Output, 8ch DI) DIO-0808RN-USB 1. Ver.1.02
N Series for USB Isolated Digital I/O Unit(8ch Relay Output, 8ch DI) DIO-0808RN-USB *The above photograph is DIO-1616HN-USB. * Specifications, color and design of the products are subject to change without
More informationUSER MANUAL RC-76M/RC-712M MODEL: P/N: Rev 3
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: RC-76M/RC-712M P/N: 2900-300329 Rev 3 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions 3 2.3 Recycling
More informationULTRATRAK SERIES RM4000, SX4000, RM8000, SX8000, RM15000 USER MANUAL. Version 2.2
ULTRATRAK SERIES RM4000, SX4000, RM8000, SX8000, RM15000 USER MANUAL Version 2.2 UltraTrak Series User Manual Copyright 2003, Promise Technology, Inc. All Rights Reserved. Copyright by Promise Technology,
More informationColorDial Pro Enhanced wall-mounted lighting controller
Enhanced wall-mounted lighting controller Enhanced wall-mounted lighting controller ColorDial Pro is an Ethernet-based, stand-alone lighting controller and interface for intelligent RGB and intelligent
More informationCellular Shades MOTORIZED SKYLIGHT. Simplicity with rechargeable batteries. Installation & Care Instructions
Cellular Shades MOTORIZED SKYLIGHT Simplicity with rechargeable batteries Installation & Care Instructions 152741B 7/2/2018 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill,
More informationInstallation Instructions Installation Guidelines. Product Summary. For the maximum number of bus devices and touchpads per panel see Table 1.
Document Number: 466-1632 Rev. B September 2000 Product Summary The ITI SuperBus 2000 2 x 20 LCD (liquid crystal display) Alphanumeric Touchpad gives you complete on-site system programming and operation
More informationFDS / FDS-R / FDS-PS
FDS / FDS-R / FDS-PS USER MANUAL For use with 120V 60Hz input. Output is 120V 60Hz at 5amps 600W MAX. switched. ETL LISTED Conforms to UL STD 1241 3091594 79-15167-00 REV. A www.fiberstars.com Page 1 of
More informationInstallation Guide Serial Interface T942SI
Installation Guide 2003-02-8/ Ver. C Contents.... General... 2 Board Description... 2 3 Installation... 4 3. Mounting... 4 3.2 Opening the Housing... 4 3.3 Mounting together with other Units... 5 3.4 Wiring
More informationQuick Start Guide. 8/16-19 LCD KVM Switch. GCL1908 / GCL1916 PART NO. Q1323-a / Q1324-a.
Quick Start Guide 8/16-19 LCD KVM Switch GCL1908 / GCL1916 PART NO. Q1-a / Q1-a www.iogear.com Package Contents 1 1 x GCL1908 / GCL1916 19 LCD KVM with Rock Mount Kit 1 x USB KVM Cable; 1 x PS KVM Cable
More informationS7999D SOLA Operator Interface Display
S7999D Operator Interface Display INSTALLATION INSTRUCTIONS APPLICATION The S7999D is microprocessor-based color touch-screen Operator Interface (OI) display that provides an operator interface for monitoring
More informationLA600WH WIRED / WIRELESS DOOR CHIME
LA600WH WIRED / WIRELESS DOOR CHIME To register this product, visit: www.nutone.com THIS PACKAGE INCLUDES: Wired / Wireless Door Chime with MP3 upload capability Decorative White Chime Cover USB Cable
More informationIntegration and Cabling Guide HAWM-UX/UF Height Adjustable Wall Mount
Integration and Cabling Guide HAWM-UX/UF Height Adjustable Wall Mount Product Registration If you register your SMART product, we ll notify you of new features and software upgrades. Register online at
More informationResidential/Light Commercial Remote Control System
MODULAR CONTROLLER REMOTE CONTROL Residential/Light Commercial Remote Control System OWNER S MANUAL AND INSTALLATION INSTRUCTIONS CONTENTS INTRODUCTION 2 SYSTEM COMPONENTS - REMOTE 3 SYSTEM COMPONENTS
More information1.3 Operating Conditions -40 F to 150 F (-40 C to 65 C) 0% to 90% Relative Humidity, non-condensing
The Keri NXT-6RK is a keypad reader typically used for card + PIN dual verification applications. It transmits keypad data in either 8-bit burst (default) or 26-bit Wiegand formats and can be used as a
More informationHANDBOOK FOR THE MOBYL DATA CENTER 22
HANDBOOK FOR THE MOBYL DATA CENTER 22 1 For support contact us at support@addc.net www.addc.net 516.673.4444 1983 Marcus Ave. Suite 104 Lake Success, NY 11042 HANDBOOK FOR THE MOBYL DATA CENTER 22 TABLE
More informationMotorized Flat Panel TV Lift
Mounting Instructions Item No.: 421.68.443 & 421.68.444 Motorized Flat Panel TV Lift Content 1. Important safety instructions. 2. Specifications and main dimensions. 3. Parts included. 4. Installation.
More informationTABLET DOCK USER S GUIDE
Fujitsu Stylistic ST Series Tablet PC TABLET DOCK USER S GUIDE Warning Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other
More informationMARINE HEADUNIT MS-RA50
MARINE HEADUNIT MS-RA50 USER INTERFACE AND CONTROLS LICENSING CONTROL PANEL LAYOUT Apple, the Apple logo, ipod and itunes are trademarks of Apple Computer, Inc., registered in the US and other countries.
More informationINSTALLING ColorDMD LED DISPLAY IN BALLY GAMES WITH DISPLAY ON LAMP BOARD
INSTALLING ColorDMD LED DISPLAY IN BALLY GAMES WITH DISPLAY ON LAMP BOARD These instructions are for mounting a ColorDMD LED display in a Bally game that has the display mounted on the swinging backbox
More informationNext Gen Sarix Enhanced IME Series Mini Dome Cameras
Next Gen Sarix Enhanced IME Series Mini Dome Cameras Installation Manual C1338M 3/17 1 Contents Important Notices...3 Legal Notice...3 Regulatory Notices...3 Korean Class A EMC...3 Warranty Statement...3
More informationDocumentation on all Paxton products can be found on our web site -
01/11/2011 Ins-30091-US PROXIMITY LCD reader Paxton Technical Support 1.800.672.7298 support@paxton-access.com Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST) Documentation on
More informationENCELIUM EXTEND Manager Wiring and installation manual Light is OSRAM
www.osram.us/extend ENCELIUM EXTEND Manager Wiring and installation manual Light is OSRAM Overview The ENCELIUM EXTEND Manager is a gateway that interfaces to both IT equipment (servers, LAN, etc) and
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationSERIES 5100XXX8 INSTALLATION & SPECIFICATION GUIDE
SERIES 5100XXX8 INSTALLATION & SPECIFICATION GUIDE Microframe Corporation 604 South 12th Street Local: 918-258-4839 Toll Free: Website: www.microframecorp.com E-mail: support@microframecorp.com Revision
More informationBPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical
More informationActiveSite. Color Dial Pro. Product Guide
ActiveSite Color Dial Pro Product Guide Easily configure and control LED light shows is an Ethernet-based, stand-alone lighting controller and interface for intelligent RGB and intelligent white (iw) LED
More informationComponents. Tools for Setup. Installation Outline
VANTAGE PRO AND VANTAGE PRO PLUS Fan-Aspirated ISS Retrofit Kit Installation Instructions Estimated Time Required: 60 Minutes These instructions describe how to install the Vantage Pro Fan-Aspirated Integrated
More informationTruVision Series 5 IP Camera Installation Guide
TruVision Series 5 IP Camera Installation Guide P/N 1073339-EN REV B ISS 13SEP17 Copyright Trademarks and patents 2017 United Technologies Corporation, Interlogix is part of UTC Climate, Controls & Security,
More informationHow to Design Custom Enclosures for Motherboard-Based Systems
PROTOCASE TECHNICAL BULLETIN How to Design Custom Enclosures for Motherboard-Based Systems (covering ATX and Mini ITX form factors) Document Edition - 1 Last Updated: June 6 th,2011 Protocase, Inc. All
More informationThe Nureva Span ideation system. Installation guide. Single panoramic system
The Nureva Span ideation system Installation guide Single panoramic system Important SAFETY WARNINGS Prior to the installation of this product, the installation instructions should be completely read and
More informationNow with Picture Memory
Intrasonic Technology, Inc. Color Video Door Phone / Intercom Installer s Manual Model No.V304KIT-R Now with Picture Memory Please read this manual carefully before the products are installed.technical
More informationSeries Amp Pad Mount Quick Connect Input and Output Power Panels
Series 300 2000-4000 Amp Pad Mount Quick Connect Input and Output Power Panels DANGER is used in this manual to warn of a hazard situation which, if not avoided, will result in death or serious injury.
More informationBAR-USB-SW. Installation Guide. Barcode Swipe Reader. and BAR-USB-SWI
BAR-USB-SW and BAR-USB-SWI Barcode Swipe Reader Installation Guide FCC Declaration of Conformity (DoC) Compliance Information (according to FCC 2.1077) (1) Product: BAR-USB-SW/BAR-USB-SWI The above device
More information2 Mesa Ethernet Dock User s Manual
owner s manual Mesa Ethernet Dock The Mesa Ethernet Dock is an optional accessory that provides an ethernet port for networking, power input jack, USB client port, and a mounting station for the Mesa Rugged
More informationCubePro. Main PCB Replacement Guide. Prosumer 3D Printer. Original Instructions
CubePro Prosumer 3D Printer Main PCB Replacement Guide Original Instructions 1 INTRODUCTION COPYRIGHT 2014 by All rights reserved. This document is subject to change without notice. This document is copyrighted
More informationDome Camera. Hardware Manual Z81, Z /01/08
Dome Camera Hardware Manual Z81, Z82 2018/01/08 Table of Contents Precautions 3 Regulatory Compliance... 4 Safety and Compliance Information... 5 Introduction 7 List of Models... 7 Package Contents...
More informationSMART Audio CAS-340 and CAS-360 Classroom Amplification System Installation Guide
SMART Audio CAS-340 and CAS-360 Classroom Amplification System Installation Guide Product Registration If you register your SMART product, we ll notify you of new features and software upgrades. Register
More informationUSER MANUAL. RC-74DL Master Room Controller MODEL: P/N: Rev 4
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: RC-74DL Master Room Controller P/N: 2900-000691 Rev 4 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions
More informationWaiting Room Network Installation Manual
Waiting Room Network Installation Manual Version 5.0 March 27 th, 2013 PCM Help Desk 1-877-233-9114 Page 1 Table of Contents System Overview 3 Tool List 4 Installation Guide 5 Site Notification 5 Install
More informationLED Maintenance Instructions
Chapter 5 LED Maintenance Instructions This guide describes the maintenance procedures for the LED portion of your DayStar or TekStar sign. 1.800.237.3928 stewartsigns.com Rev1802 Intentionally Left Blank
More informationNintendo DSi Wi-Fi Antenna Board
Nintendo DSi Wi-Fi Antenna Board Replacement Replace your Nintendo DSi's Wi-Fi antenna. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION Use this guide to replace
More informationAB-2D AB-2D SPEAKER A,B OR A+B SELECTOR INSTALLATION & OPERATION GUIDE
M O D E L AB-2D AB-2D SPEAKER A,B OR A+B SELECTOR INSTALLATION & OPERATION GUIDE AB-2D Speaker/Amplifier Selector TABLE OF CONTENTS Introduction 1 Features and Benefits 1 Installation Considerations 3
More informationWireless Area Controller (WAC50) i. Installation Instructions
i. Installation Instructions Daintree s WAC50 Wireless Area Controller (WAC) is at the heart of Current s energy management solution. It provides intelligent control across a large area. Using open and
More informationReplacing the Gateway M275 Keyboard
Replacing the Gateway M275 Keyboard This package includes a replacement keyboard for your Gateway M275 notebook and these printed instructions. Tools you need You need a small Phillips screwdriver and
More information