T3 Series Bacnet Programmable Controller

Transcription

1 T3 Series Bacnet Programmable Controller T3000 controller is a multi-user,including T3-BB, T3-LB and T3-TB.It can stand DDC panel alone or in a multiple network system with full communication capabilities.the multiple communication ports allow the controller to operate on a network or host sub networks and to communicate with local and remote operators simultaneously. Setup and programming are done on a PC not necessary to connect to live hardware as it is the case with many systems. When the program is ready for on-site testing, connect it to a live panel and download the T3000 software. Programming can be done remotely over the network and modem connections as well.the network system is very flexible and economical for the installation. T3-BB T3-TB T3-LB 10 Year WARRANTY

2 Specifications Software Interactive dynamic color graphics Industry standard Bacnet & Modbus protocols User programming, built in networking features 16 Control Basic programs 16 User screen displays 8 Weekly routines, 4 annual routines 128 User variables 16 PID controllers 8 passwords or users Hardware Highly Configurable: any combination of input/ output cards totalling up to 64 points Digital output: 5V/125VAC, 30DVC Analog output: 0-10V Universal input: Thermistor, 0-10V, 0-5V, 0-20mA Mechanical relays 2A, 24VAC/DC Diagnostic LEDs & Hand-Off-Auto Switches 512K Flash / 512k Ram SD Disk slot for trend logs, alarms, graphics Ethernet Port: Bacnet & Modbus supported simultaneously 2 x RS485 ports USB Port only for T3-BB, T3-LB RS232 only for T3-BBt Zigbee port is optional, only for T3-BB, T3-LB Clock with battery backup Surge-protected Universal Inputs with 12-bit resolution UL listed ABS enclosure with rubberized texture creates a high end feel. Software configure the I/O ranges with the free T3000 software or by writing to the registers with your own software. Each output has a hand-off-auto switch for easy troubleshooting and overrides. Each I/O as well as the RS485 connections have a separate screw terminal, there s no need to gang two wires under one terminal for any of the terminations. High/Low speed input pulse counters RS485 sub baudrates: 9600, RS485 main baudrates: 1200~ Transportation methods are RS485, Ethernet, USB, Zigbee but it can, at the same time, support Modbus and Bacnet. Source code for the modules is available with your first purchase. T3000 front end is free and open source: Compiled version of the front end is here: Power Supply Voltage: 24V AC/DC Relay: 5A/125VAC, 30VDC Operating Temperature: -30~70 C (-22~158 F) Maximum Power Consumption T3-BB: 10W T3-LB: 10W T3-TB: 6W Case Color: Black Part Number Scheme

3 Network Diagram T3000 Building Automation System Overview Building Operator Ethernet T3-BB T3-LB T3-TB T3-8o T3-22i Remote User Expansion I/O MAIN NET1 RS485 RS485 SUBNET2 RS485 TSTAT8 TSTAT6 TSTAT7 TSTAT8 CHILLERS VALVES BTU METERS BOILERS VALVES FAN COIL VAV Dimensions 1) T3-BB(Big Brother) 2) T3-LB(Little Brother) 2) T3-TB(Little Brother)

4 Wiring Diagram 32 UNIVERSAL INPUTS 32 UNIVERSAL INPUTS T3-BB WIRING DIAGRAM 12 DIGITAL OUPUTS AIR HANDLER THERMOSTAT TEMPERATURE FILTER SWITCH OCCUP SENSOR FLOW SENSOR FAN STATUS WINDOW CHANGEOVER FREEZE PROTECT POWER METER BTU METERS TX RX GND INPUTS RS232 RS485 RS ETHERNET POWER GND 12-24V AC/DC 24 VAC - OUT 110/220 VAC - IN FAN COIL HEAT PUMP 112 HYDRONICS 24VAC 24VAC 12 ANALOG OUPUTS MODULATING VALVES RS485 SUBNET PORT2 MODULATING DAMPERS RS485 SUBNET PORT1 LAN USB 32 UNIVERSAL INPUTS T3-LB WIRING DIAGRAM 12 DIGITAL OUPUTS AIR HANDLER THERMOSTAT TEMPERATURE FILTER SWITCH OCCUP SENSOR FLOW SENSOR FAN STATUS WINDOW CHANGEOVER FREEZE PROTECT POWER METER BTU METERS UI 6 DO 4 AO ETHERNET 24VAC LAN FAN COIL 2ANALOG OUTPUTS MODULATING VALVES MODULATING DAMPERS HEAT PUMP RS485 MAIN NETWORK HYDRONICS RS485 SUBNET NETWORK GND 24V AC/DC 24 VAC - OUT 110/220 VAC - IN

5 T3-TB WIRING DIAGRAM 4DIGITAL OUTPUTS 11INPUTS AIR HANDLER THERMOSTAT TEMPERATURE FILTER SWITCH OCCUP SENSOR FLOW SENSOR FAN STATUS WINDOW CHANGEOVER FREEZE PROTECT POWER METER BTU METERS INPUTS OUTPUTS ETHERNET LAN FAN COIL HEAT PUMP HYDRONICS 33 2UNIVERSAL OUTPUTS 34 2ANALOG OUTPUTS AO G 24VAC MODULATING VALVES MODULATING DAMPERS RS485 MAIN NETWORK RS485 SUBNET NETWORK GND 24V AC/DC 24 VAC - OUT 110/220 VAC - IN T3-TB Output Jumper Settings

6 Controller T3-BB Big Brother T3-LB Little Brother T3-TB Tiny Brother Total Channels: Universal Input Analog Output Relay Output Universal Output 2* Comm ports: RS RS Ethernet USB Option port** * The 2 universal output can be selected by jump as either 1-10V analog or relay outputs. ** zigbee module. Transportation methods of these units are RS485, Ethernet, USB, Zigbee,at the same time, they support Modbus and Bacnet. The T3-BB unit features 32 channels input and 24 channels output including 12 channels analog output and 12 channels digital output. As for the T3-LB, there are 16 channels input and 10 channels output including 4 channels analog output and 6 channels digital output. For T3-TB, it includes 11 inputs and 8 outputs which contain 2 analog outputs, 4 digital outputs and 2 universal outputs. All of these channels can be controlled directly by minipanel through input and output cards. Highlight

7 T3000 Operation Instructions 1. Download T3000 software and install it. 2. Take an example of T3-BB here, connect T3-BB to PC by RS485 network at pin 94, 95, and 96 or Ethernet. 3. Open T3000 software, and click icon building, an popup window will appear, set protocol to Auto, then close it. Click scan icon which is next to the icon building to find the connected unit. 1.Click to scan Device detected 2.Click to close Then click the device log what have been connected, T3000 software will show the info in righ hand place. You can click Input, Output and other icon. 4.Click input to show table right 3.Click to select minipanel

8 4. Click input icon, it will show all inputs in T3000 software. T3 Series Bacnet Programmable Controller T3-BB T3-LB T3-TB Speed Low Speed Input channels Hz High Speed Input channels M Hz For T3-BB, T3-LB, T3-TB, all the inputs channels have pulse counters. High speed counters capable of 1M Hz. Low speed inputs channels reach to 1 hz per channel. Here we take an example of T3-BB, showing how to configure the high speed and low speed counters in T3000 software. 5.Click input to show table below

9 5. Click output icon, it will show the output view. T3 Series Bacnet Programmable Controller Click input to show table below

10 *6.Steps to get zigbee information by T Click the device with zigbee 2.Click to see table below Zoom 3.Zigbee setting here now

11 Register List Address Num Length Description 0~3 1 4 Reserved for serial numbler 4~5 1 2 firmware Version Number Modbus device address Prodouct model Hardware Version Number PIC rev Temporary address for plug-n-play addressing scheme reserved UART0 Baudrate , Enable node plug and play ISP Version Reserved Update status reserved UART1 Baudrate , UART2 Baudrate.(UART_1200 = 0, UART_2400 = 1, UART_3600 = 2, UART_4800 = 3, UART_7200 = 4, UART_9600 = 5, UART_19200 = 6, UART_38400 = 7, UART_57600 = 8, UART_ = 9, UART_ = test cmd, write 77 - reboot, set default paramer, erase prg, clear tstat db board type, big or small. 1 - big, 2 - samll,3-tiny,4-vav instance number station number EN clear tstat db USB MODE EN DYNDNS,// 0 - no 1 - disable 2 - enable DYNDNS provider, // dyndns update timer NETWORK: MSB, MSB MSTP NETWORK: MSB, MSB TOP hardware c8051f023 firmware rev sm5964 firmware rev "com0 configure MAIN_MSTP = 0,MAIN_MODBUS = 1,MAIN_PTP = 2,SUB_GSM = 3,MAIN_ZIG = 4,SUB_ZIG = 5,SUB_ MODBUS = 6 "

12 Address Num Length Description com1 configure MAIN_MSTP = 0,MAIN_ MODBUS = 1,MAIN_PTP = 2,SUB_GSM = 3,MAIN_ZIG = 4,SUB_ZIG = 5,SUB_MODBUS = com2 configure MAIN_MSTP = 0,MAIN_ MODBUS = 1,MAIN_PTP = 2,SUB_GSM = 3,MAIN_ZIG = 4,SUB_ZIG = 5,SUB_MODBUS = write flash time after changed setting. Unit is minute Reserved 100~ reg100, MAC address, read only reg106, DHCP setting. 0=static IP; 1= DHCP 107~ IP address: MSB, MSB-1, MSB-2, LSB 111~ SUBNET MASK address: MSB, MSB-1, MSB-2, LSB 115~ GATEWAY address: MSB, MSB-1, MSB-2, LSB reg119, 0, TCP server reg120, listen port at TCP server mode 200~ Last Time Sync second min hour day day of week month year number of device which is connected to T3 controller 300~ id of sub tstat 500~ Number of AV AI AO BI BO 7000~ test 8000~ output input variable controller WR AR PRG TBL 8008~ TZ AMON GRP ARRAY UNIT USER ALARM TSTAT NAME SET 8020~ output value, (digital output, ON - 512, OFF - 0) 8084~ output swith status (SW_OFF - 0, SW_AUTO - 1, SW_HAND - 2) 8148~ "output range (0 - unused) { UNUSED=0, OFF_ON, CLOSED_OPEN, STOP_START, DISABLED_ENABLED, NORMAL_ALARM, NORMAL_HIGH, NORMAL_LOW, NO_YES, COOL_HEAT, UNOCCUPIED_OCCUPIED, LOW_HIGH, ON_OFF, OPEN_CLOSED, START_STOP, ENABLED_DISABLED, ALARM_NORMAL, HIGH_NORMAL, LOW_NORMAL, YES_NO, HEAT_COOL, OCCUPIED_UNOCCUPIED, HIGH_LOW, custom_digital1, custom_digital2, custom_digital3, custom_digital4, custom_digital5, custom_digital6, custom_digital7, custom_digital8 } Digital_units_equate;"

13 Address Num Length Description 8212~ output auto or manual (0 - auto, 1- manual) 8276~ output type, digital or analog (0 - digital 1 - analog) 8340~ input value 8404~ input filter 8468~ input calibration 8532~ input sign calibration 8596~ "input range (not_used_input = 0, Y3K_40_150DegC, Y3K_40_300DegF, R10K_40_120DegC, R10K_40_250DegF, R3K_40_150DegC, R3K_40_300DegF, KM10K_40_120DegC, KM10K_40_250DegF, A10K_50_110DegC, A10K_60_200DegF, V0_5, I0_100Amps, I0_20ma, I0_20psi, N0_2_32counts, N0_3000FPM_0_5V, P0_100_0_5V, P0_100_4_20ma, P0_255p_min, table1, table2, table3, table4, table5,100 - HI_SPEED_COUNTER )" 8660~ high speed counter1~6 8672~ high speed counter1~6 flag, 0 - start, 1 - stop, 2 -clear 8678~ input type, 0- thermistor, 1-5v, 2-10v, 3-20ma 8820~ value of VAR1-VAR ~ A/M of VAR1-VAR ~ for test, tatst information 30000~ for test, monitor task Support BACnet Object Type: analog-input, analog-output, analog-value, binary-input, binary-output, device Support BACnetService: who-is, i-am object-identifier, object-name, object-type, present-value, units, object-list, vendor-id, vendorname, system-status, confirmed-service, unconfirmed-service

14 BIP object T3-BB T3-LB T3-TB Analog-variable AV1-10 AV1-10 AV1-10 Analog-input: AI1~32 AI1~16 AI1~11 For BB, LB, TB, if add expansion modules, maximum inputs can reach to 64 Analog-output: AO1~12 AO1~4 AO1~4 Binary-output: BO1~12 BO1~6 BO1~2 Outputs: For BB, LB, TB, if add expansion modules, maximum outputs can reach to 64. T3-TB itself has total 8 outputs, while there are 2 universal ouputs can be used as analog output, or binary output. Device: obect-identifier object-name object-list