2100 Digital Indicator Quick Start Manual For use with Software Versions 2.0 and above

Size: px

Start display at page:

Download "2100 Digital Indicator Quick Start Manual For use with Software Versions 2.0 and above"

Bathsheba Bridges
5 years ago
Views:

1 2100 Digital Indicator Quick Start Manual For use with Software Versions 2.0 and above

2 Rinstrum Digital Indicator Quick Start Manual Rev 2.50 Copyright All Rights Reserved. No part of this document may be copied, reproduced, republished, uploaded, posted, transmitted, distributed, stored in or introduced into a retrieval system in any form, or by any means (electronic, mechanical, photocopying, recording or otherwise) whatsoever without prior written permission of Rinstrum Pty Ltd. Disclaimer Rinstrum Pty Ltd reserves the right to make changes to the products contained in this manual in order to improve design, performance or reliability. The information in this manual is believed to be accurate in all respects at the time of publication, but is subject to change without notice. Rinstrum Pty Ltd assumes no responsibility for any errors or omissions and disclaims responsibility for any consequences resulting from the use of the information provided herein. SPECIAL NOTE Trade Use of the Rinstrum 2100 This manual may occasionally make reference to Trade Use settings of the Only properly marked Trade Certified versions of the 2100 can be used in Legal for Trade applications. Trade Certification is only available on 2100 instruments with software Versions 2.0 and above. Some individual settings may not be legal for trade use. Please check regulations with the appropriate Weights and Measures Authority. Everything should be made as simple as possible, but not simpler. - Albert Einstein - Page 2

3 Rinstrum Digital Indicator Quick Start Manual Rev 2.50 Table of Contents 1. INTRODUCTION Approvals Features rin-smart Software Options Manuals SPECIFICATIONS WARNINGS General DC Power Supply Load Cell Signals and Scale Build Configuration Issues INSTALLATION Special Function Key Electrical Safety CONNECTIONS Connecting Shields Cable Shield Connection and Earthing Unused Pins Load Cell Connection FULL SETUP SAFE SETUP OPERATOR MENU SETUP ENABLING SOFTWARE OPTIONS RS-485 COMMUNICATIONS ERROR MESSAGES BATTERY OPERATION DIAGNOSTIC ERRORS...23 Page 3

4 Rinstrum Digital Indicator Quick Start Manual Rev Introduction This manual contains information on the installation, calibration and setup of the Approvals NSC S403 approval (6000 divisions at 1µV/division). NMI TC6033 approval (6000 divisions at 1µV/division). C-tick approved and CE approved Features 27mm alphanumeric LCD display (LED back-lighting). Programmable special function key and three remote inputs. Full setup and calibration. Six wire load cell wiring. Checkweighing, kg/lb switching, totalising, intelligent batching, counting, live weight, hold/peak hold functions. Five point linearity correction. Real Time Clock and Calendar. RAM for storing Zero, Tare and Total settings, etc. Soft Power On/Off for inactivity auto power down rin-smart Software Options 0224 (SERIAL) Enable RS-232 serial communications 0225 (SETP) Enable setpoint output 1.4. Manuals For more information on the 2100 refer to the 2100 Reference Manual and 2100 Operator Manual (available free of charge from Page 4

5 Rinstrum Digital Indicator Quick Start Manual Rev 2.50 Performance Display Backlight Display Resolution Count-by Zero Cancellation Span Adjustment Stability/Drift Operating Environment Digital 2. Specifications Backlit alphanumeric LCD with six 27mm high digits LED backlight with adjustable brightness Up to 30,000 divisions, minimum of 0.25µV/division (Trade 6000 divisions at 1µV/division) 1, 2, 5, 10, 20, 50, 100 (Entered in Displayed Weight) + / 2.0mV/V 0.1mV/V to 3.0mV/V full scale Zero: < 0.1uV/ C, Span < 10ppm/ C, Linearity < 20ppm, Noise < 0.05µVp-p Temperature: 10 to +50 C ambient, Humidity: <90% non-condensing Setup and Calibration Full digital with visual prompting in plain messages Memory Retention Full non-volatile operation Digital Filter Averaging from 1 to 100 consecutive readings Zero Range Adjustable from +/ 2% to +/ 20% of full capacity A/D Converter Type 24bit Sigma Delta Resolution 8,388,608 internal counts A/D Sync Filter Selectable 25/30Hz, FIR filter > 80dB Load Cells Excitation 8 volts for up to 8 x 350 ohm load cells (6-wire + shield) Serial Comms (Software Option 0224) Serial output Single RS-232 as automatic transmit, network or printer drive Power Input Standard General 10 to15vdc (60mA to 400mA depending on load cells and backlight) ON/OFF key with override and Auto-Off software Variants AC AC Power: 110/240VAC 50/60Hz 10VA fitted in s/s housing DC DC Power: 12-24VDC 10VA fitted in s/s housing Battery Rechargeable: 12VDC Battery fitted in s/s housing Dimensions Body size 189mm (L) x 99mm (H) x 23mm (D) Panel cutout Flush mounted with cable holes drilled separately (template provided) Page 5

6 Rinstrum Digital Indicator Quick Start Manual Rev Warnings 3.1. General Instrument not to be subject to shock, excessive vibration or extremes of temperature (before or after installation). Inputs are protected against electrical interference, but excessive levels of electro-magnetic radiation and RFI may affect the accuracy and stability. For full EMC or for RFI immunity, termination of the load cell shield at the 2100 end is important. Instrument and load cell cable are sensitive to excessive electrical noise. Install well away from any power or switching circuits DC Power Supply DC supply need not be regulated provided it is free of excessive electrical noise and sudden transients. Instrument can be operated from high quality plug-pack provided there is sufficient capacity to drive both it and load cells. Use plug packs with a rating of 10VDC to 12VDC with current outputs of 0.5 to 1A Load Cell Signals and Scale Build Very low output scale bases can be used but may induce some instability in weight readings when used with higher resolutions (ie. higher output/lower number of divisions equals greater display stability/accuracy) Configuration Issues Configuration and calibration can be performed from front panel, using digital setup. When Full Setup is used, all menu items are accessible and care must be taken to ensure no accidental changes are made to calibration and trade settings. Enter a passcode to prevent unauthorised or accidental tampering. Page 6

7 Rinstrum Digital Indicator Quick Start Manual Rev Installation The following steps are required to set up the 2100 indicator. Inspect indicator to ensure good condition. Ensure mounting options and connectors are available. Use connection diagrams to wire up load cell, power and auxiliary cables as required. Connectors for all cables are supplied with indicator. Instrument has built in panel mounting screws. Use the "Panel Drilling Template" provided for hole locations. Connect Power to instrument and press <POWER> key (if not overridden) to start instrument. Follow instructions in Full Setup section page 12 to configure and calibrate instrument. Enter passcode to protect settings from tampering. Record passcode for future reference. To turn instrument OFF press and hold <POWER> key for three seconds (until display blanks) Special Function Key The Special Function Key on the 2100 ships as a blank key. If any of the special functions are to be used on the indicator it is important that the matching function key sticker (supplied) is applied to the keypad. Ensure keypad is clean and dry before affixing sticker. Cleaning Keypad: Wipe with a soft cloth slightly dampened with either methylated spirits or warm soapy water Electrical Safety For your protection all mains electrical hardware must be rated for environmental conditions of use. Pluggable equipment must be installed near an easily accessible power socket outlet. To avoid the possibility of electric shock or damage to the instrument, always switch off or isolate the instrument from the power supply before maintenance is carried out. Page 7

Connecting Shields To obtain full EMC or for RFI immunity with the 2100, the load cell shield MUST be connected electrically to the

8 Rinstrum Digital Indicator Quick Start Manual Rev Connections 5.1. Connecting Shields To obtain full EMC or for RFI immunity with the 2100, the load cell shield MUST be connected electrically to the metal shell of the DB9 connector. Refer to diagrams below or to instructions supplied with the connector. Fold shield wires back over outside of cable insulation so cable clamp of backshell makes good electrical contact with shield when installed. Twist shield wires together and solder ends to DB9 casing. Page 8

9 Rinstrum Digital Indicator Quick Start Manual Rev Cable Shield Connection and Earthing Care should be taken when connecting shields to maximise RFI immunity and minimise earth loops and cross-talk (interference) between instruments. For RFI immunity, termination of the load cell shield at the 2100 end is important (ie. with connection to the 2100 case via the shield connection). The 2100 enclosure is directly connected to the shield connections on the cables. The 2100 should be connected to earth via a single reliable link to avoid earth loops. Where each instrument is separately earthed, interconnecting cable shields should be connected at one end only. Caution: Some load cells connect the cable shield directly to the load cell (and therefore the scale base). Connection of the shield in this situation may be site specific. The instrument complies with relevant EMC standards provided case ground connection is correctly made. Resistance measured between 2100 case and nearest earth point should be less than 2 ohms. If static problems are expected, options 0084/0085 may be required to protect the serial outputs Unused Pins Unused pins are NOT to be connected. Reason: The functions of the pins may not be compatible with equipment at the other end (eg. connecting output pins to a PC communications port may affect the operation of the PC). Page 9

10 Rinstrum Digital Indicator Quick Start Manual Rev Load Cell Connection Wire Connection Note: Sense lines MUST be connected Wire Connection *For more information on shielding refer to page 8. Page 10

11 Rinstrum Digital Indicator Quick Start Manual Rev Auxiliary Connection *For more information on shielding refer to page 8. Note: Do NOT connect unused pins. For more information refer to page 9. Remote Display 2100 Pin Remote Display Plug 3 (TXD) RXD / Receive 5 (GND) GND / Ground Printer 2100 Pin Printer Plug - DB25F 3 (TXD) RXD - Pin 3 5 (GND) GND - Pin 7 4 (DTR) DTR - Pin 20 Direct Computer Link 2100 Pin Computer DB-9F (DB-25F) 2 (RXD) TXD - Pin 3 (Pin 2) 3 (TXD) RXD - Pin 2 (Pin 3) 5 (GND) GND - Pin 5 (Pin 7) Page 11

Rinstrum - 2100 Digital Indicator Quick Start Manual Rev 2.50 5.4.4. IO Connections 5.4.5. Power Warning For 2100 use only 10-15 VDC Voltages outside this range may cause improper operation or damage.

Ensure instrument is On. Press the <ZERO> and <POWER> keys together for two seconds.

12 Rinstrum Digital Indicator Quick Start Manual Rev IO Connections Power Warning For 2100 use only VDC Voltages outside this range may cause improper operation or damage. Note: Variants of the 2100 may require different power requirements. Refer to Variant Data Sheet. 6. Full Setup Full Setup provides access to configure and calibrate the instrument. Ensure instrument is On. Press the <ZERO> and <POWER> keys together for two seconds. To save settings, exit and return to normal weighing mode, press the <ZERO> and <POWER> keys together for two seconds or select - End - from the menus. Indicates setting is trade critical and calibration counter will be incremented if setting is changed. Indicates functions are only suitable for remote inputs. Page 12

13 Rinstrum Digital Indicator Quick Start Manual Rev 2.4 GRP ITM SEL EDT OK Underline = Defaults BUILD DP Decimal Point Position , , , , , CAP Maximum Capacity SEL changes position, EDT changes digit. RES Resolution (Count-By) 1, 2, 5, 10, 20, 50, 100 UNITS Units of Measure none, g, kg, lb, t, oz HI.RES Resolution x 10 Mode OFF, ON OPTION USE Industrial or Trade Use TRADE (Trade), INDUST (Industrial) (+ and weighing) FILTER Digital Filtering/Averaging 1, 2, 5, 10, 25, 50, 75, 100 (number of readings) MOTION Motion Detection Setting none, t, t, t (fine), t, t, t, t (coarse) Default = 0.5 graduations per 1.0 second (Time) AUTO.Z Auto Zero on Power Up OFF, ON Z.TRAC Zero Tracking Setting OFF, SLOW (0.5 div/sec), MED (2 div/sec), FAST (10 div/sec) Z.RANGE Zero Key Range 2+2, 1+3, (% of full scale) Z.BAND Zero 'Dead' Band SEL changes position, EDT changes digit. Page 13

14 Rinstrum Digital Indicator Quick Start Manual Rev 2.4 GRP ITM SEL EDT OK CAL ZERO Zero Calibration Routine (Current weight displays) SPAN Span Calibration Routine (Current weight displays) ED.LIN Edit Linearisation Points L Select Linearisation point 1 to 5 (L2, L3, L4, L5). (Approx. % of full scale) CLR.LIN Clear Linearisation Points L Select Linearisation point 1 to 5 (L2, L3, L4, L5). (Approx. % of full scale) FAC.CAL Factory Calibration Cont.N (No) Cont.Y (Yes) Underline = Defaults Remove all weight. OK starts routine (Z.in P displays). ITM key to exit, OK to repeat routine. Add test weight. Set correct weight. SEL changes position, EDT changes digit. OK starts routine (S.in P displays). ITM key to exit, OK to repeat routine. Set capacity of test weight. SEL changes position, EDT changes digit. OK starts routine (L.in P displays). ITM key to exit, OK to repeat routine. OK to clear point or ITM key to exit. Cont.N Warning: Choosing Cont.Y will restore default factory calibration in BUILD and CAL menus. Page 14

15 Rinstrum Digital Indicator Quick Start Manual Rev 2.4 SPEC OP.PC Security Passcode for (0000 no passcode). Operator Menu Setup Set 4 digit passcode (eg. 1234). SEL changes position, EDT changes digit. Activated only when FULL.PC is also set. FULL.PC Full Security Passcode for Digital Setup KEY.LOC Front Panel Key Locking Zero, Tare, Gross/Net, Print KEY.FN Key Functions Position 1: Keypad Function Key Positions 2, 3 & 4: Remote Inputs (0000 no passcode). Set 4 digit passcode (eg. 1234). SEL changes position, EDT changes digit. Z T G P Letter indicates key is unlocked. (-) Dash indicates key is locked. SEL changes position, EDT changes digit. ( no functions assigned). Keypad Function Key: U lb/kg switching, C Count, H Hold, E Peak Hold, L Live Weight, S Show Total, B Batch, (-) No function. Remote Inputs: Z Zero, T Tare, G Gross/Net, P Print, U lb/kg switching, C Count, H Hold, E Peak Hold, L Live Weight, S Show Total, B Batch, K Blank, (-) No function (enable IO pin as output). Front Panel Keys: Z Zero, T Tare, G Gross/Net, P Print B.LIGHT Backlight Operation ON, AUTO, OFF (Automatically turns instrument off after 10 seconds of inactivity) BRIGHT Backlight Brightness 01 to 10 (01=10%, 10=100%) Page 15

16 Rinstrum Digital Indicator Quick Start Manual Rev 2.4 GRP ITM SEL EDT OK Underline = Defaults SPEC ctd. AUT.OFF Automatic Power Off NEVER, 20 S, 30 S, 60 S, 300 S, 600 S (Seconds of inactivity before power down) AUX.DSP Auxiliary Display (Time) OFF, TIME (Recommended for batching Operations) SYNC A/D Frequency 25Hz or 30Hz (This setting may affect calibration.) SERIAL TYPE Serial Output Type OFF, NET, AUTO, PRINT, MASTER ADDR Serial Address 00 to 31 (Default = 01) SEL changes position, EDT changes digit. BAUD Serial Baud Rate 1200, 2400, 4800, 9600, BITS Serial Format Options N (Default Serial Format Options) Position 1: Parity SEL changes position, EDT changes digit. Position 2: Data Bits Parity: N None, O Odd, E Even Position 3: Stop Bits Data Bits: 7 or 8 data bits Position 4: DTR Handshake Stop Bits: 1 or 2 stop bits DTR: (-) DTR disabled or d DTR enabled PRN.ID Printout ID OFF, ON (Adds ADDR ID to printouts) Page 16

17 Rinstrum Digital Indicator Quick Start Manual Rev 2.4 SERIAL PRN.ROW Row Padding on Printout 00.0 to ctd Number of line feeds to add before printout Number of line feeds to add after printout. If padding is set to 10 then a form feed character is sent. PRN.COL Column Padding on Printout 00 to 20 (Number of spaces to add at start of each line of printout.) SET.PTS OPTN A - G O H - - G O H - (Default Setpoint Settings) - none - None disables the setpoint when not in use Active A Active for level control and overload alarms Slow S Slow Fill used in conjunction with Fast Fill Gross G Gross (use gross weight) Net N Net (use net weight, Tares before operating relay) Reading R Reading (use current displayed weight) Held H Held (use Held reading) Over O Over (weight increasing) Under U Under (weight decreasing, negative weighing) High H High (Active High logic) Low L Low (Active Low logic) - none - None (no internal beep during relay operation) Single S Single (one internal beep during operation) Double D Double (double internal beeps during operation) Flash F Flash (Display flashes) TARG A Target A SEL changes position, EDT changes digit. (Primary target in batching) Page 17

18 Rinstrum Digital Indicator Quick Start Manual Rev 2.4 GRP ITM SEL EDT OK SET.PTS ctd. OPTN B - G O H - -none Gross Over High -none Active Net Under Low Single Fast Reading Double Held Flash TARG B Target B (Preliminary value in batching) OPTN C - G O H - -none Gross Over High -none Active Net Under Low Single Dump Reading Double Pass Held Flash Underline = Defaults - G O H - (Default) Same as OPTN A except: F Fast Fill used in conjunction with Slow Fill. SEL changes position, EDT changes digit. - G O H - (Default) Same as OPTN A except: D Dump signal for weight to return to zero or dump time (refer to D.TIME below). P Pass output for setpoint 3 only. (checkweigh application) TARG C Target C (Not used in batching) SEL changes position, EDT changes digit. FLIGHT In-Flight SEL changes position, EDT changes digit. HYS Hysteresis SEL changes position, EDT changes digit. D.TIME Dump Time 00.0 to 20.0 seconds 0 for dump to zero weight, otherwise operated for the time specified. Page 18

19 Rinstrum Digital Indicator Quick Start Manual Rev 2.4 CLOCK TIME Time Setting 24 hour clock Set time in the format HH.MM HH.MM.SS displays SEL changes position, EDT changes digit. DATE Date Setting Set day and month in the format DD.MM DD.MM.YY displays Set the year in the format YYYY QA.OPT Quality Assurance Reminder OFF, ON (Flashes QA Due on due date) QA.DATE Quality Assurance Due Date Set day and month in the format DD.MM Set the year in the format YYYY TEST SCALE Load Cell Test Displays load cell output in mv/v (Format=0.0000) Trade Mode=5 sec display FRC.OUT Force Outputs (Default display) EDT advances through each output (1--, -2-, --3) TST.INP Test Inputs (Default display) EDT advances through each input (1--, -2-, --3) FACTRY DEFLT Restore Factory Defaults Cont.N Cont.N (No) Warning: Choosing Cont.Y will clear all stored Cont.Y (Yes) data except calibration. CONFIG Configure Software Options Used to enter license codes for software options. - END - EXIT SETUP settings and return to normal weighing mode Page 19

Rinstrum - 2100 Digital Indicator Quick Start Manual Rev 2.4 7. Safe Setup Safe Setup provides access to configure the instrument without access to trade or calibration specific items.

To save settings, exit and return to normal weighing mode, press the <GROSS/NET> and <POWER> keys together for two seconds or select - End - from the menus. 8.

20 Rinstrum Digital Indicator Quick Start Manual Rev Safe Setup Safe Setup provides access to configure the instrument without access to trade or calibration specific items. Ensure instrument is On. Press the <GROSS/NET> and <POWER> keys together for two seconds. To save settings, exit and return to normal weighing mode, press the <GROSS/NET> and <POWER> keys together for two seconds or select - End - from the menus. 8. Operator Menu Setup The Operator Menu provides access to setpoint target and flight settings. Ensure instrument is On. Press the <TARE> key for two seconds. To save settings, exit and return to normal weighing mode, press the <TARE> key for two seconds or select - End - from the menus. 9. Enabling Software Options To enable any of the rin-smart Software options a license code must be entered. The license codes are unique to each option and to each instrument. These options may be factory installed or installed in the field. Follow the steps below to discover which options are installed or to install another option: Ensure the instrument is On. Press the <POWER> and <FUNCTION> keys together for two seconds. Page 20

Rinstrum - 2100 Digital Indicator Quick Start Manual Rev 2.

SERIAL is displayed if the RS-232 Serial Option is installed).

21 Rinstrum Digital Indicator Quick Start Manual Rev 2.4 The 2100 will display the installed options and prompt for a new license code. (eg. SERIAL is displayed if the RS-232 Serial Option is installed). The <GROSS/NET> key changes the position and the <PRINT/M+> key changes the digit. (A code of leaves the instrument unchanged.) Press the <FUNCTION> key when complete. The 2100 returns to normal operation. If successful the new rin-smart Option will be displayed, otherwise the 2100 will sound a beep. Page 21

22 Rinstrum Digital Indicator Quick Start Manual Rev RS-485 Communications The 2100 is compatible with the RI 0080 RS-232 to RS-485 serial converter. There is no need to provide external power to the RI 0080 module as this is provided directly by the Error Messages Error Description (U ) The weight reading is below the normal weighing range. (O ) The weight reading is above the maximum capacity of the equipment. (ZERO) The weight is outside the zero range (ERROR) tolerance setting. See Note below. (STABLE) The scale motion has prevented a zero, (ERROR) tare or print operation from occurring. See (QA) (DUE) Note below. Quality assurance testing is due. Press any key to clear this warning for one hour. Note: The ZERO and STABLE error messages are accompanied by a series of long beeps. The messages repeat until a key is pressed. 12. Battery Operation BAT is flashed on the auxiliary display if the battery voltage falls below 11V. If the battery voltage falls below 10.5V the instrument automatically powers down. Battery checking is only carried out if the Automatic Off (AUT.OFF) option is set to a value other than NEVER. Page 22

23 Rinstrum Digital Indicator Quick Start Manual Rev Diagnostic Errors Error Description Action E00001 Power supply voltage too low. Check supply E00002 Power supply voltage too high. Check scale / cables E00004 E00008 E00010 E00020 Load cell excitation voltage too low. (8 volts for up to 8 x 350 ohm load cells) Load cell excitation voltage too high. (8 volts for up to 8 x 350 ohm load cells) Temperature outside limits. ( 10 to +50 C ambient) Scale build incorrect. (100 to grads). Page 23 Check scale / supply Check scale / supply Check location Fix up scale build E00100 Digital setup information lost. Re-enter setup E00200 Calibration information lost. Re-calibrate E00300 All setup information lost. Enter setup and calibrate E00400 Factory information lost. (FATAL) Service E00800 EEPROM memory chip failed. Service (FATAL) E02000 ADC out of range. Possible load cell or cable damage. Check load cell cable E04000 Battery backed RAM data lost. Re-enter setup E08000 FLASH program memory incorrect. (FATAL) Service The E type error messages are additive. For example, E00005 ( ) would indicate that both Excitation and Power Supply Voltage are low. The numbers add in hexadecimal as follows: A - B - C - D - E - F (For example, = 6, or = C)

IP69K Washdown Indicator Quick Start Manual (800)

IP69K Washdown Indicator Quick Start Manual (800) 223-4227 www.cas-usa.com U21022050 Table of Contents 1. INTRODUCTION...2 1.1. Approvals...2 1.2. Manuals...2 2. SHIPPING CONTENTS...2 3. SPECIFICATIONS...3