IOT x86 Joule Gateway

Transcription

1 IOT x86 Joule Gateway TM

2 Gumstix, Inc. shall have no liability of any kind, express or implied, arising out of the use of the Information in this document, including direct, indirect, special or consequential damages. Gumstix, Inc. may have patents, patent applications, trademarks, copyrights, trade secrets or other intellectual property rights pertaining to Gumstix products described in this document (collectively Gumstix Intellectual Property ). Except as expressly provided in any written license or agreement from Gumstix, Inc., this document and the information contained therein does not create any license to Gumstix s Intellectual Property. The Information contained herein is subject to change without notice. Revisions may be issued regarding changes and/or additions. Copyright c 2017, Gumstix, Inc. All rights reserved.

3 Board Description Go Geppetto Simple design for a high performance IOT gateway using an Intel Joule module. Incorporates Zigbee with UART headers for Z-Wave. BLE and Wifi on the chip, USB Ethernet included. Board Dimensions 10.35cm x 7.75cm i

4 Contents 1 Modules on Board COM Connectors Intel R Joule TM Module Connector (v30) (1) Network USB-Ethernet Module with Hub (v3) (2) ZigBee (v5) (3) Z-Wave Wireless Modem (v1) (4) Power Real Time Clock (v9) (5) V/1.5A Regulator (v11) (8) Power Connectors Barrel Connector (5V 3A) (v7) (6) USB USB mini-b (Vertical) (v5) (7) Connectivity USB-UART (v16) (9) Headers Joule Fan Connector (Vertical) (v3) (10) IO Tactile Switch (v15) (11) Top-side LED (v3) (12) Top-side LED (v3) (13) Top-side LED (v3) (14) Module Connections Graph 6 3 Module Power Graph 7 ii

5 IOT x86 Joule Gateway 1 1 Modules on Board 1.1 COM Connectors Intel R Joule TM Module Connector (v30) (1) The Intel R Joule TM module is a quad-core x86-64 compute module with 4 GB DDR4 RAM, 16 GB emmc, agn + ac WiFi, and BT 4.2. The module connector s 2 x 100-pin Hirose connectors provide capacitive touch LCD, MIPI DSI, HDMI and USB 3.0, as well as low-speed GPIO and serial communication buses. The Intel R Joule TM module s datasheet is available at: The Intel R Joule TM module connector recieves: VCC 5.0 from Barrel Connector (5V 3A) (6) The Intel R Joule TM module connector provides the following outputs: 3V3 to:

6 IOT x86 Joule Gateway 2 ZigBee (3) Top-side LED (14) Top-side LED (13) Top-side LED (12) Z-Wave Wireless Modem (4) VLOGIC to: ZigBee (3) Real Time Clock (5) Tactile Switch (11) Z-Wave Wireless Modem (4) USB-UART (9) GPIO382 to USB-Ethernet Module with Hub (2) USB2 1 HOST to USB-Ethernet Module with Hub (2) GPIO272 to Tactile Switch (11) I2C1 to Real Time Clock (5) GPIO378 to Top-side LED (12) GPIO379 to Top-side LED (13) GPIO380 to Top-side LED (14) GPIO270 to Z-Wave Wireless Modem (4) UART0 to ZigBee (3) GPIO412 to ZigBee (3) UART2 4W to USB-UART (9) UART1 to Z-Wave Wireless Modem (4) 1.2 Network USB-Ethernet Module with Hub (v3) (2) This module offers a 10/100 Base-T Ethernet connection, as well as a 2-port USB hub via USB connection to USB2 1 HOST on Intel R Joule TM Module Connector (1).. The Microchip LAN9512 integrated USB hub and 10/100 ethernet controller provides up- and down-stream hi-speed USB 2.0 PHYs and 10/100BASE-T MAC and PHY. For technical data for the LAN9512 download the datasheet at:

7 IOT x86 Joule Gateway ZigBee (v5) (3) ZigBee transeivers, Compliant with IEEE standard , provide low-rate wireless personal area networks (LP-WPANs) with reduced power consumption. The ZigBee tranciever module includes a Silicon Labs ETRX357 zigbee Radio Module and communicates on a UART bus to the compute device on a Geppetto board. Technical documentation for the ETRX357 is available at: This module is connected to UART0 on Intel R Joule TM Module Connector (1) Z-Wave Wireless Modem (v1) (4) FULLY INTEGRATED Z-WAVE WIRELESS MODEM WITH ON-BOARD ANTENNA This module is connected to UART1 on Intel R Joule TM Module Connector (1). 1.3 Power Real Time Clock (v9) (5) This real-time clock backup is powered by a 6mm coin cell battery. The MI DS1340 RTC is programmed over I2C and is connected to a crystal oscillator at 32.8 khz. NOTE: The RTC IC used in this module is trickle-charge capable. Only NiCd cells should be used if this feature is enabled. Technical documentation for the MI DS1340 is available at: This module is connected to I2C1 on Intel R Joule TM Module Connector (1) V/1.5A Regulator (v11) (8) This DC to DC step down regulator provides a 3.3V DC output at 1.5A needed by certain components on this board. It is capable of accepting an input voltage between 3.1 to 16V DC and output is controlled by the TI TPS6211 buck regulator. It recieves 5.0V from Barrel Connector (5V 3A) (6). The dataheet for the TPS6211 regulator is available at: This regulator provides 3.3V to: USB-Ethernet Module with Hub (2)

8 IOT x86 Joule Gateway Power Connectors Barrel Connector (5V 3A) (v7) (6) This power jack is compatible with Gumstix 5V/3.5A DC power adapter using a 4.0mm x 1.7mm barrel connector. It provides more current than a standard 5V DC power supply, suitable for use with multiprocessor designs. This power jack provides 5V to the following modules: Intel R Joule TM Module Connector (1) 3.3V/1.5A Regulator (8) Joule Fan Connector (Vertical) (10) 1.5 USB USB mini-b (Vertical) (v5) (7) The vertical USB mini-b jack module is a USB port that allows this design to be connected as a USB device to an upstream USB host using a USB mini-b to standard-a cable. It is mounted at a right angle to the board for vertical insertion. This USB mini-b port is connected to USB DEVICE on USB-UART (9). 1.6 Connectivity USB-UART (v16) (9) Also known as an FTDI, this USB to UART converter allows a USB connection to the board to behave as a virtual RS232 serial connection. It offers direct and complete access to the system from a development machine by way of the FTDI FT232RQ USB UART IC. Technical documentation for the FT232RQ is available at: This USB to UART converter connects a host machine from USB mini-b (Vertical) (7) to UART2 4W on Intel R Joule TM Module Connector (1). 1.7 Headers Joule Fan Connector (Vertical) (v3) (10) This header is used to connect to a 5V fan using a JST ZH3 connector

9 IOT x86 Joule Gateway IO Tactile Switch (v15) (11) This 4.9 sq. mm pull-down touch switch provides a user input for the signal GPIO272 on Intel R Joule TM Module Connector (1) Top-side LED (v3) (12) The top-side LED module contains a 1608 standard size LED of a user-selected color, mounted on the top side of a Geppetto board. The LED is active-high on GPIO378 from Intel R Joule TM Module Connector (1) Top-side LED (v3) (13) The top-side LED module contains a 1608 standard size LED of a user-selected color, mounted on the top side of a Geppetto board. The LED is active-high on GPIO379 from Intel R Joule TM Module Connector (1) Top-side LED (v3) (14) The top-side LED module contains a 1608 standard size LED of a user-selected color, mounted on the top side of a Geppetto board. The LED is active-high on GPIO380 from Intel R Joule TM Module Connector (1).

10 IOT x86 Joule Gateway 6 2 Module Connections Graph Figure 1: excludes power modules

11 IOT x86 Joule Gateway 7 3 Module Power Graph