Certificate of Compliance

Transcription

1 Certificate of Compliance Certificate: (LR 18656) Master Contract: Issued to: Honeywell Inc. 512 Virginia Dr Fort Washington, PA USA Attention: Edward A. Child The products listed below are eligible to bear the CSA Mark shown Issued by: Mitchell Rushing Mitchell Rushing PRODUCTS CLASS PROCESS CONTROL EQUIPMENT - For Hazardous Locations Class I, Division 2, Groups A, B, C and D: HC900 Hybrid Controller, consisting of Racks, Power Supply, Processor/Communication and I/O Modules; Max. Ambient 60 C., unless noted. System components are as listed below: Model Number Description Electrical Rating T Code 900R04-00XX 4 I/O Slot Rack 5 Vdc, 6A; 24 Vdc, 2A T6 900R08-01XX 8 I/O Slot Rack 5 Vdc, 6A; 24 Vdc, 2A T6 900R08 R-01XX8 I/O Slot Rack 5 Vdc, 6A; 24 Vdc, 2A T6 900RPE-00XX Redundant Power Supply Extension Rack 5Vdc, 6A; 24 Vdc, 2A T6 900RR0-00XX Redundant CPU Rack 5 Vdc, 6A; 24 Vdc, 2A T6 DQD 507 Rev Page: 1

2 900R12-01XX 12 I/O Slot Rack 5 Vdc, 6A; 24 Vdc, 2A T6 900R12R-01XX 12 I/O Slot Rack 5 Vdc, 6A; 24 Vdc, 2A T6 900P01-00XX Power Supply Module Vac, Hz, 63 VA max 900P02-00XX Power Supply Module Vac, Hz, 130 VA max 900P24-00XX 24Vdc Power Supply Module 24 Vdc, 60W 900C31-00XX Controller CPU Config. SW & Doc 5 Vdc, 600 ma T5 900C32-00XX Controller CPU 5 Vdc, 600 ma T5 900C51-00XX Controller C50 CPU Config. SW & Doc 5 Vdc, 600 ma T5 900C52-00XX Controller C50 CPU 5 Vdc, 600 ma T5 900C53-00XX I/O Scanner Module 5 Vdc, 600 ma T5 900C71R-00XX Controller CPU Config. SW & Doc 5 Vdc, 1500 ma T5 900C72R-00XX Controller CPU Redundant 5 Vdc, 1500 ma T5 900C73R-00XX Redundant Scanner 5 Vdc, 770 ma T5 900C71-00XX Controller CPU Config. SW & Doc. 5 Vdc, 1500 ma T5 900C72-00XX Controller CPU 5 Vdc, 1500 ma T5 900A01-01XX Analog Input Module, 8 Channel ±10 Vdc, 10 μa per Ch. T6 900B01-01XX Analog Output Module, 4 Channel 21. ma into 750 ohms per Ch. 900B08-01XX Analog Output Module, 8 Channel 21. ma into 750 ohms per Ch. 900B16-01XX Analog Output Module, 16 Channel 21. ma into 750 ohms per Ch. T3C 900G01-01XX Digital Input Module (Contact Type) Vdc, 3.1 ma per Ch. T5 900G02-01XX Digital Input Module, 16 Channel DQD 507 Rev Page: 2

3 (24 Vdc) Vdc, 10.8 ma per Ch. 900G03-01XX Digital Input Module, 16 Channel (120/240 Vac) Vac, 2.6 ma per Ch. 900G04-01XX Digital Input Module, 16 Isolated Channel 0-264Vac, 2.6mA per Ch. 60C 0-150Vdc, 2.5mA per 40C 900H01-01XX Digital Output, Relays (8 Channel) 4A max/ch T5 900H02-01XX Digital Output Module, 16 Channel (24 Vdc) 32vdc@2A/ch, 8A max per module 900H03-01XX Digital Output Module, 8 Channel (120/240 Vac) 250 Vac, 2A per Ch., 8A max per module 900H32-01XX Digital Output, 10.5 tp 32Vdc, 32 Ch 32 Vdc, 0.5 A per Ch., 12A per module T6 900K01-01XX Pulse/Freq/Quadrature Module, 4 Ch 5 Vdc, 17 ma / input Ch;5 Vdc, 0.5 A each PSM Power Status Module 5 Vdc, 22 ma T6 RSM Redundant Switch Module 5 Vdc, 22 ma T6 NPE 1533 Alternate Power Supply Input Vac, Hz, 0.7A max. Output 5V/2A, 24V/0.9A NPE 1534 Alternate Power Supply Input Vac, Hz, 1.4A max. Output 5V/6A, 24V/2.0A NPE 2232 Alternate Power Supply Input Vdc, 5A max. DQD 507 Rev Page: 3

4 Output 5V/6A, 24V/2.0A. Notes: 1. The above HC900 devices are for rack mounting in a suitable protective enclosure, in accordance with the manufacturer's instructions, subject to acceptance by the local authority having jurisdiction. 2. The above model is Equipment Class I, Pollution Degree 2, Installation Category II, Continuous Operation. APPLICABLE REQUIREMENTS CAN/CSA Standard C22.2 No. 0-M91 (Reaffirmed 2006) CAN/CSA Standard C22.2 No. 94-M94 (Reaffirmed 2006) CAN/CSA Standard C22.2 No General Requirements - Canadian Electrical Code, Part II Special Purpose Enclosures Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use, Part 1: General Requirements (Includes Amendment 1) CAN/CSA Standard C22.2 No B-97 Amendment 2 to CAN/CSA-C22.2 No , "Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use - Part 1: General Requirements" CSA Standard C22.2 No. 213-M1987 (Reaffirmed 2008) MARKINGS Non-incendive Electrical Equipment for Use in Class I, Division 2 Hazardous Locations In addition to those markings specified for the Ordinary Locations Certification ( ), the following markings appear on a CSA Certified permanent adhesive nameplate, applied to the housing: Listee name: "Honeywell", or CSA Master Contract Number , adjacent to the CSA Mark in lieu of manufacturers name. Model number: As specified in the PRODUCTS section, above. Electrical ratings: As specified in the PRODUCTS section, above. Ambient temperature rating: As specified in the PRODUCTS section, above. Manufacturing date in MMYY format, or serial number, traceable to month of manufacture. Enclosure ratings: TYPE X, and IP xx (Model 1040 Series only). DQD 507 Rev Page: 4

5 The CSA Mark, as shown on the Certificate of Conformity. Hazardous Location designation: Class I, Division 2, Groups A, B, C, D (may be abbreviated). Temperature code: As specified in the PRODUCTS section, above. The following words: o WARNING EXPLOSION HAZARD - Substitution of components may impair suitability for Class I, Division 2. (This marking may be provided separately with unit in installation documentation). o WARNING EXPLOSION HAZARD Do not connect while circuit is live unless area is known to be nonhazardous. (May be silkscreened on housing or frame of mounting rack). o Install per Operator Interface User Guide, Doc (Model 1040 Series only), or reference to appropriate installation documentation (all other models) Note - Jurisdictions in Canada may require these markings to also be provided in French language. It is the responsibility of the manufacturer to provide bilingual marking, where applicable, in accordance with the requirements of the Provincial Regulatory Authorities. It is the responsibility of the manufacturer to determine this requirement and have bilingual wording added to the "Markings". DQD 507 Rev Page: 5