Copyboard (Network board) N-31S/N-31W/N-314 User s Manual

Size: px

Start display at page:

Download "Copyboard (Network board) N-31S/N-31W/N-314 User s Manual"

Norman Edwards
5 years ago
Views:

1 Copyboard (Network board) N-31S/N-31W/N-314 User s Manual Thank you for your purchase of the PLUS Copyboard. Please read this User s Manual carefully before use to take full advantage of the functions of this product. After you have finished reading the manual, please keep it for future reference.

2 Introduction This manual is for the network board (model name: N-31S/N-31W/N-314). Model Type N-31S Standard size for two screens N-31W Wide size for two screens N-314 Standard size for four screens fied. NOTE - - E-2

3 Introduction...E-2 Package Contents...E-4 Names of the Parts...E-5 Front... E-5 Input/output terminals... E-6 Changing the Height of the Unit... E-7 Control Panel... E-8 Keypad panel... E-9 Functions of the Network board...e-10 Printing Functions... E-10 Saving Functions... E-11 Operation Steps...E-12 Setting the Time...E-13 Printing (printer sold separately)...e-15 Preparing the Printer... E-15 Preparing the Printer connected to a Network... E-15 Basic Printing Operation... E-16 Moving the sheet surface manually... E-18 Printing Thumbnails... E-18 Consecutive Printing... E-19 Changing Printing Color... E-19 Using USB Memory...E-20 USB Memory Storage Procedure... E-20 Saving Image Files on a Computer/Deleting Image Files... E-22 Using the network board connected to a computer...e-24 CB Setup (Operating the Network Board s Buttons)...E-26 Basic setting operation... E-26 Table of Function Numbers and Settings... E-27 Meaning of Error Messages...E-29 Troubleshooting...E-31 Scanning Adjustment (White Calibration)...E-33 Specifications...E-34 Appendix...E-35 Connections and Wiring Diagram... E-35 - E-3

4 The package contents are as described below. Please check before use. - - Model:LTE36E-S2-3 Manufacture:Li Tone Electronics Co.,LTD, E-4

5 Front E-5

6 - E-6

7 This is the height adjustment when setting up the network board on the optional stand. The stand height can be adjusted to 3 levels by 100 mm. (1) Unplug the power cord from the wall power outlet, then disconnect all the connection cords from the main unit. (2) Remove the locking knobs (one on each side). (3) Change the position of the main unit support pieces. Lift the main unit about 1 cm to unhook it. Insert the stand s hooks securely into in the mounting holes in the main unit s support pieces (one on each side). (4) Fasten the two locking knobs (left and right) to the mount support pieces. (5) Connect all the connection cables. Stand E-7

8 The control panel of the drawing refers to Model N-31S/N-31W. When pressing a button, please press the center area (the square bulge). The button may not work if it is pressed on a corner E-8 -

9 1 onds) E-9

10 E-10

11 Blip! 10 E-11

12 The network board uses an image scanner to scan characters or diagrams drawn using special markers (four colors). The image can be printed out to the printer and be stored on a USB memory device or a computer. When network settings are made with a network connected to the network board, the image can be saved on the network board or a FTP server, or can be printed out to the network printer on the network. To use a network, refer to the separate N-31 Series Network Manual. - E-12

13 The date and time are stamped on the printing paper and recorded in the file information when files are stored on the network board and FTP server, so set the network board s time correctly. The time can also be set from a computer via a network (when connected to a LAN). In this section, operation for setting the time by using buttons on the network board is provided. 1 2 Day Hours Minutes E-13

14 - - E-14

15 Use a printer to print out the image that has been drawn on the sheet surface. Use a PLUS-designated printer. Operations and names of parts differ from printer to printer. For details of operations, see your printer s operating instructions. The network board can print out to the printer connected to the network board or a network E-15

16 - or - - E-16

17 or - - E-17

18 1. or selection - screens 1 of 4 screens zontally) of 4 screens cally) screen) (1) 2. or E-18

19 1. - Screens 1 and 2 (Screens 1 and 2 Screens 1 to 3 Screens 1 to 4 or 2. or N-314) - 1. E-19

20 The content of what has been drawn on the sheet surface of the network board can be saved in USB memory. Later, the saved image can be read into a personal computer and made into a document of the proceedings of the meeting, or affixed to a document. - - E-20

21 Display window - or - E-21

Examples of operations follow for saving the image files in the USB memory device to the hard disk of the personal computer, and for deleting the folder when the USB memory capacity is full.

22 Examples of operations follow for saving the image files in the USB memory device to the hard disk of the personal computer, and for deleting the folder when the USB memory capacity is full. (There are various methods that can be used for saving and deleting including the use of Explorer.) See the instruction manual of your personal computer or the software that you are using for information about using a personal computer. The name of the folder on the USB memory device is CB_Image. Image files are stored in this folder. By factory setting upon purchase, image files are named PV-xxx.png (PNG files), where xxx refers to a 3-digit number starting from 001 (ex.: PV-001.png). When consecutive storing is performed, numbers -1 or -2 ( -1, -2, -3 or -4 on model N-314) are added to the end of the file name. (Example: When three screens are stored consecutively - PV png, PV png.) When a file format is specified to PDF, consecutive stored files will be merged into one file. Images can be stored in JPEG, PNG or PDF format, selectable in the network board settings ( CB Setup ). (See pages E-26.) E-22

23 E-23

24 When the network board and a computer are connected by USB cable, the network board is recognized as an external memory device (removable device). Below is the procedure for copying the CBImage file from this device onto the computer. Images can be stored in JPEG (.jpg), PNG (.png) or PDF (.pdf) format, selectable in the network board settings ( CB Setup ). (See pages E-26.) The factory default is PNG. - Display window E-24

25 - - E-25

26 There are two ways to make the device settings: using the network board s operation buttons to make the settings ( CB Setup ) and making the settings via the web on the computer connected to a network. The description here provides operation using the network board s buttons. For using the network board connected to a network, refer to the separate N-31 Series Network Manual. - - Dot lit E-26

27 Description Valid* Standard tion* - - Not lit E-27

28 Description DD-MMM- MMM-DD- E-28

29 If any of the following flashing indications appear in the display window of the control panel, please check the matters described below. Error messages flash for 5 seconds, then stop flashing, remaining lit. nected - - Security protection connected - printer is connected E-29

30 connected - nection failure reset error E-30

31 Please check the following matters before making a request for servicing E-31

32 Also see the descriptions of error indications at Network (main unit) related errors on page E E-32

33 If dark lines (horizontal black lines) on a printed out hard copy or image on the screen are generated, you need to optimally adjust the sensitivity of reading the sheet surface. If the scanning image does not work due to generation of dark lines, update the program and perform the white calibration in the following steps. 1. Use the supplied white board cleaner or damp cloth to clean the 20 cm of width on the left edge of the network board. Avoid cleaning the joint part of the sheets. Doing so may cause incorrect calibration. 2. Feed the sheet manually until the half width of cleaned sheet is covered by the frame of the network board. 1. Make sure that the network board s power is turned on. (Display on the display window is 01.) 2. Press the Scroll/Stop button (on the left) while pressing and holding the On/Standby button. 3. Release the buttons. The display CAL will be changed. * CA AL L in this order 4. Press the Save button. The display on the display window starts rotating and adjusting automatically. 5. When the display on the display window is flashing AA, press the On/Standby button. The display on the display window returns to 01, indicating that the reading adjustment is completed. E-33

34 BOARD TYPE (Model name) Standard (N-31S) Wide (N-31W) 4-screen (N-314) Form BOARD Interface Added functions Power supply Operating conditions Miscellaneous Operating environment Installation method Self-standing (T-shaped legs), or wall mounting External dimensions (T-shaped legs*¹) W1480 D675 H1947*² mm W1980 D675 H1947*² mm W1480 D675 H1947*² mm Main unit weight 20 kg*³ 25 kg*³ 25 kg*³ T-shaped legs weight 12.5 kg Panel Size H910 W1300 mm H910 W1800 mm H910 W1300 mm Effective reading size H900 W1280 mm H900 W1780 mm H900 W1280 mm Number of Pages 2 4 Paging Bi-directional, endless (Horizontal scrolling) Drive method Sheet movement Reading method CIS (Contact Image Sensor) Reading illumination light source RGB LED Reading resolution Reading time Board External memory Network Printing Clock PC connection AC power adapter File format Screen size Power consumption Temperature: Humidity: Ruled lines Miscellaneous Web browser Main scanning direction (vertical sheet surface) 1.92 dots/mm (50 dpi or equivalent) Sub scanning direction (horizontal sheet surface) 1.92 dots/mm (50 dpi or equivalent) Black & white: approx. 15 s Color: approx. 15 s Black & white: approx. 21 s Color: approx. 21 s JPEG, PNG, PDF Standard type: dots (fixed) Wide type: dots (fixed) Type USB Flash memory * 4 Compatible FAT types Interface LAN port Supported protocol Printing resolution No. print colors Printer interface Supported network printer FAT 16, 32 USB2.0 RJ-45 (10Base-T/100Base-TX) TCP/IP (FTP/FTPS, HTTP/HTTPS, DHCP, NetBIOS Name Service) 300 dpi or equivalent Eight colors or two color monochrome Conforming to USB 2.0 standards/lan port FTP supported printer * 5 Black & white: approx. 15 s Color: approx. 15 s Used for the timestamp and for file dating properties Images can be acquired and device settings made via USB (using a browser) Input : AC V/50 60 Hz, Max 0.75 A Output : DC 12 V, 3.0 A In standby: 3 W, During operation: 12 W (not including printer) Windows: Internet Explorer 8.0 or greater Macintosh: Safari 5 or greater * Enable JavaScript C 30 85% (No condensation) 50 mm cross-ruled squares Dedicated markers (black, red, blue, and green) E-34

35 To wall power outlet E-35

Copyboard M-18S/M-18W User s Manual

Copyboard M-18S/M-18W User s Manual Thank you for your purchase of the PLUS Copyboard. Please read this User s Manual carefully before use to take full advantage of the functions of this product. After