araya Logic Module Dynamic Dimming Round LED Arrays (DDM2) 24V DC Input (Constant Voltage) 5000 Maximum Peak Lumens Data Sheet

Transcription

1 Logic Module () 24V DC Input (Constant Voltage) Maximum Peak Lumens Data Sheet

2 Maximum Peak Lumens TABLE OF CONTENTS 1 Description and Key Features 2 Ordering Information 3 Electrical Specifications and Power Supplies 4 Mechanical Specifications DMX12-A Accessory Board 6 Lutron Accessory Board 7 Legrand Wattstopper DLM LMLM Module 8 DALI Accessory Board 9 Heat Sinking Recommendations 1 Case Temperature Measurement Points 11 Secondary Optics 12 Ribbon Cable Assemblies 13 Power / Control Cable Assemblies 14 Wiring Diagrams 1 eflicker Free / Hybrid Dimming 16 Pre-Installation Notes Lumenetix Inc Scotts Valley Dr. Scotts Valley, CA 966 Lumenetix, araya, Color Tuning, Dynamic Dimming and SceneSet are registered trademarks of Lumenetix, Inc. Lumenetix, Inc info@lumenetix.com ii Logic Module with Proud Member of the Dry or Damp Locations Designed in California, USA Assembled ed in Californi in USA sembled in US UL Recognized Component Dry or ry Damp or Damp Locations Location Class 2 Input Class 2 Input Revised Specifications subject to change without notice

3 1 DESCRIPTION AND KEY FEATURES Maximum Peak Lumens 216 IES PROGRESS REPORT SELECTION 216 LFI INNOVATION AWARDS CATEGORY WINNER 216 LUX AWARDS HIGHLY COMMENDED 216 EDISON REPORT TOP TEN MUST SEE LIST Logic Modules Description araya Logic Modules (ALM) connect to tunable color high-power round LED arrays that mix five colors of LEDs to deliver tunable white light that warms as it dims at 9+ CRI* and color consistency of <2 MacAdam ellipses. Delivered light dims from 3K at full intensity to 18K at % intensity, and then maintains 18K to 1%. An MR16 halogen dimming profile is offered. The ALM is connected to one LED array via low-cost ribbon cables, and features on-board driver electronics and the araya control logic for precise control of LED light output while tuning and dimming. On-board closed loop thermal feedback compensates each color channel for thermally induced variations in light output due to dimming or changes in ambient temperatures. On-board closed loop optical feedback measures the lumen depreciation of each channel and re-balances the color model to ensure color consistency over the, hour life of the LED array. A patented in-line manufacturing process captures and stores the spectral characteristics of each LED on the array, rapidly generating a unique color model for each array. The Zhaga-compliant LED arrays are compatible with traditional - 1V wired controls and feature on-board Bluetooth Low Energy (BLE) for commissioning. The arrays can access DMX12-A-RDM, Legrand Wattstopper s Digital Light Management (DLM) control interface, DALI Type 8 or Lutron EcoSystem inputs via an optional accessory board that connects to an electrically isolated expansion port within the ALM. For simple deployment, SceneSet allows up to five scenes to be pre-programmed into the LED array during production and recalled at the venue using a - 1V recommended dimmer or via Bluetooth. Commissioning of the LED array and the re-programming of Sceneset is done via the wireless araya Tunable Color 2. ios app that connects to the embedded Bluetooth radio. Key Features Dimming profile that warms as it dims, launching at 3K at full intensity to 18K from % down to 1% 9+ CRI* Integrated driver electronics and logic On board thermal and optical feedback for color consistency of <2 step MacAdam ellipse over, hour life On-board thermal turndown In-line spectral capture and storage creates an unique color model for each Zhaga-compliant LED array, resulting in consistent CRI and CCT across all arrays Compatible with - 1V wired controls On-board Bluetooth Low Energy (BLE) for commissioning DMX12-A-RDM, Wattstopper DLM, DALI Type 8 or Lutron EcoSystem control accessibility via optional accessory board that connects to an electrically isolated compartment within the ALM SceneSet enables up to five scenes to be preprogrammed and recalled using a - 1V recommended dimmer or via Bluetooth DMX slots set by RDM or via wireless araya Tunable Color 2. ios app araya Tunable Color 2. ios App 3 Logic Module with Revised Specifications subject to change without notice

4 2 ORDERING INFORMATION Maximum Peak Lumens Photometrics and Ordering Codes (Round LED Array Kits) 1 Dimming Range: 3-18K Specifications 2 Dimming Profile MR16 CRI (Ra) Across Tuning Range >9* Dimming Nominal Color Consistency Color Consistency Over Life Lumen Maintenance Nominal Wattage LES 3 Peak Source Lumens Peak Delivered Lumens 4 (±1%) Ordering Code 31.6 mm 43 6W mm 3 26 W mm W mm W % to 1% in increments of 1% at variable CCT <2 MacAdam ellipse (±.2 Duv from ANSI curve) Calibration maintains original color points over life L7 (7% of initial lumens) at, hours 1. Kits include round LED array and araya Logic Module with on-board -1V and Bluetooth LE, as a factory pre-matched set which MUST be kept that way during installation for proper operation and control and CANNOT be separated. The kits do not include ribbon cables, power cable assembly, control cable assembly, or accessory boards (see below for accessory ordering specifications). 2. Specifications are within +/- 1% of the nominal value. Peak efficacy is not necessarily at typical peak lumens. 3. LES = Light Emitting Surface. 4. Peak delivered lumen values are listed for modules tested with the included dome diffuser. *From 2-3K. Accessories (Ordered Separately) Quantity Description Ordering Code long jacketed/round 16-pin ribbon cable (16-pin Tyco Connector at one end, 2-pin JST connector at other end) (for connecting ALM to round array) 18 long flat 16-pin ribbon cable (16-pin Tyco Connector at one end, 2-pin JST connector at other end) (for connecting ALM to round array) long 2-wire ALM power cable assembly long 7-wire ALM control cable assembly DMX12-A-RDM Accessory Board*** Lutron Accessory Board*** DALI Accessory Board*** Legrand Wattstopper DLM - LMLM Module*** *** Accessory boards are shipped pre-attached to the ALM, & cannot be shipped individually. Accessory boards for different controls should NOT be interchanged in the field. This will void the Lumenetix warranty. 4 Logic Module with Revised Specifications subject to change without notice

5 3 ELECTRICAL SPECIFICATIONS Maximum Peak Lumens 3.1 Electrical Specifications ( LOGIC MODULE) Input Voltage 24V DC (Constant Voltage) Nominal Power Input* 3W, 4W, 6W, and 8W Nominal Current Input 1.2A (3W); 1.7A (4W); 2.A (6W); 3.3A (8W) Power Supply Classification Class 2 (UP TO 1W RATED POWER) Power and Control Connector Power Connector: Molex 2322; Control Connector: Molex Ribbon Cable Connector (supplied by third parties) TE Micro-Match (requires TE mating connector ) Control Options** 1V, DMX12-A-RDM, Wattstopper DLM, Lutron EcoSystem, DALI Type 8 CCT and Dimming Control Connections Plug-in connector for 24 gauge leads *araya Logic Module (ALM) power dissipation is up to 1% of total power dissipation. Therefore ALM must be provided with adequate heat sink capability when applicable. **DMX12-A-RDM, Lutron EcoSystem, DALI Type 8 or Wattstopper Digital Light Management control compatibility requires optional accessory board. IMPORTANT The araya Logic Module (ALM) has on-board drive electronics, including dimming. A dimming driver should NOT be used. 3.2 Recommended Power Supplies (Constant Voltage) Manufacturer Part Number Rated Power Mean Well APV W P Efore / Roal Strato RSLP3-24 3W P Mean Well APV W P P ERP VLM4W-24 4W P P 9 mm array (2W) 12 mm array (3W) 19 mm array (W) 32 mm array (6W) Amperor ANP-11-24P L-1-P 6W P P P ERP VLM6W-24 6W P P P Mean Well IRM-6-24ST 6W P P Mean Well LPV W P P P Efore / Roal Strato RSLP7-24 7W P P P P Mean Well LPF W P P P P ERP VLM1W-24 96W P P P P Mean Well GST12A24-R7B 12W P* P* P* P* CAUTION: Using a constant current power supply will damage the module, and will void the Lumenetix warranty. Using a triac or dimming driver will damage the module, and will void the Lumenetix warranty. The power supply MUST be evaluated with the module(s) that it will be operated with. If a recommended power supply from the above list is not used, it will void the Lumenetix warranty. If unqualified power supplies are used in a fixture, it will void the Lumenetix warranty. It is the responsibility of the fixture manufacturer to ensure that the power supply performance does not change over time. The Lumenetix warranty is void if problems occur as a result of such changes. *U.L. CLASS 1 NON-NORTH AMERICA ONLY. NOTES: Recommendations are subject to change. Consult your Lumenetix representative for the most updated list. IMPORTANT: Please contact the power supply manufacturer to verify that the current version of the listed power supply still meets the latest Lumenetix testing approvals / qualifications.. Power supply qualification process:: if a power supply that is not part of the above list is submitted for testing to Lumenetix (during the design-in phase), it will be qualified or disqualified within two weeks of submission. Logic Module with Revised Specifications subject to change without notice

6 4 MECHANICAL SPECIFICATIONS Maximum Peak Lumens 4.1 Round LED Array Kits Array Dimensions (LES; Diameter D ; Height H ) LES = Light Emitting Surface. LES = 31.6 mm (nominal 1.24 in.) LES = 19.7 mm (nominal.78 in.) LES = 12.6 mm (nominal. in.) LES = 9.6 mm (nominal.38 in.) D = 6 mm (nominal 2.36 in.); H = 16.3 mm (nominal.64 in.) D = mm (nominal 1.97 in.); H = 1 mm (nominal.9 in.) D = mm (nominal 1.97 in.); H = 12.9 mm (nominal.1 in.) D = 4 mm (nominal 1.7 in.); H = 1.1 mm (nominal.4 in.) araya Round LED Array (31.6 mm LES; lumens) All dimensions are in millimeters. araya Round LED Array (19.7 mm LES; 3 lumens) All dimensions are in millimeters araya Round LED Array (12.6 mm LES; 2 lumens) All dimensions are in millimeters. araya Round LED Array (9.6 mm LES;1 lumens) All dimensions are in millimeters. 6 Logic Module with Revised Specifications subject to change without notice

7 4 MECHANICAL SPECIFICATIONS Maximum Peak Lumens 4.2 araya Logic Module ALM Dimensions (H x W x L) H = 1.11 mm (.6 in.); W = 3 mm (1.18 in.); L = 133 mm (.24 in) Dimensions provided are for the ALM without optional accessory boards. 2X THRU ALL 3 2X 21 2X 1 2X 9 6 2X araya Logic Module All dimensions are in millimeters. The mounting holes are mm in diameter. 7 Logic Module with Revised Specifications subject to change without notice

8 DMX12-A ACCESSORY BOARD Maximum Peak Lumens.1 araya Logic Module with DMX12-A-RDM Accessory Board ALM Dimensions (H x W x L) H = mm (.69 in.); W = 3 mm (1.18 in.); L = 133 mm (.24 in.) 2X THRU ALL X X araya Logic Module with DMX Accessory Board and Cover Dimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches. The mounting holes are mm in diameter..2 Mechanical Specifications (DMX12-A-RDM Accessory Board) Lumenetix part #: Wire Specifications: AWG, stranded tinned copper (TC) only Connector: Phoenix Contact X 18. 2X X DMX Accessory Board All dimensionss are in millimeters. 8 Logic Module with Revised Specifications subject to change without notice

9 DMX12-A ACCESSORY BOARD Maximum Peak Lumens.3 Mounting Specifications (DMX Accessory Board) The Accessory Board is mounted on the 1-pin header and located on the two bosses, and then captured in place to the ALM with two (2) self-tapping screws. Screw Specifications: Phillips Rounded Head Thread-Forming Screws for Plastic, 18-8 Stainless Steel, Number 4 Size, 1/8" Long; McMasterCarr # 99461A1. Torque Specifications: 2. to 2. in-lb CAUTION: The screws are very small and are self-threaded into small plastic bosses. Overtorquing will strip the plastic and damage the ALM housing. 9 Logic Module with Revised Specifications subject to change without notice

10 6 LUTRON ACCESSORY BOARD Maximum Peak Lumens 6.1 araya Logic Module with Lutron EcoSystem Accessory Board ALM Dimensions (H x W x L) H = 2.3 mm (.81 in.); W = 3 mm (1.18 in.); L = 133 mm (.24 in.) X.2 THRU X X araya Logic Module with Lutron Accessory Board and Cover Dimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches. The mounting holes are mm in diameter. 6.2 Mechanical Specifications (Lutron EcoSystem Accessory Board) Lumenetix part #: Wire Specifications: AWG, solid wire or tin-dipped stranded Connector: TE X Lutron Accessory Board All dimensionss are in millimeters. 1 Logic Module with Revised Specifications subject to change without notice

11 6 LUTRON ACCESSORY BOARD Maximum Peak Lumens 6.3 Mounting Specifications (Lutron EcoSystem Accessory Board) The Accessory Board is mounted on the 1-pin header and located on the two bosses, and then captured in place to the ALM with two (2) self-tapping screws. Screw Specifications: Phillips Rounded Head Thread-Forming Screws for Plastic, 18-8 Stainless Steel, Number 4 Size, 1/8" Long; McMasterCarr # 99461A1. Torque Specifications: 2. to 2. in-lb CAUTION: The screws are very small and are self-threaded into small plastic bosses. Overtorquing will strip the plastic and damage the ALM housing. 11 Logic Module with Revised Specifications subject to change without notice

12 7 WATTSTOPPER DLM LMLM MODULE Maximum Peak Lumens 7.1 araya Logic Module with Legrand Wattstopper s DLM LMLM Module ALM Dimensions (H x W x L) H = 2.27 mm (.8 in.); W = 3 mm (1.18 in.); L = 133 mm (.24 in.) X X.2 THRU ALL 2X X X araya Logic Module with LMLM Module and Cover Dimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches. The mounting holes are mm in diameter. 7.2 Mechanical Specifications (LMLM Module) Lumenetix part #: Wire Specifications: Solid 2/3 AWG, red/blue/black Connector: TE Legrand Wattstopper DLM LMLM Module Dimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches. 12 Logic Module with Revised Specifications subject to change without notice

13 7 WATTSTOPPER DLM LMLM MODULE Maximum Peak Lumens 7.3 Mounting Specifications (LMLM Module) The LMLM Module is mounted on the 1-pin header and located on the two bosses, and then captured in place to the ALM with two (2) selftapping screws. Screw Specifications: Phillips Rounded Head Thread-Forming Screws for Plastic, 18-8 Stainless Steel, Number 4 Size, 1/8" Long; McMasterCarr # 99461A1. Torque Specifications: 2. to 2. in-lb CAUTION: The screws are very small and are self-threaded into small plastic bosses. Overtorquing will strip the plastic and damage the ALM housing. Please refer to the Legrand Wattstopper website for detailed specifications, wiring diagrams and installation instructions: 13 Logic Module with Revised Specifications subject to change without notice

14 8 DALI TYPE 8 ACCESSORY BOARD Maximum Peak Lumens 8.1 araya Logic Module with DALI Type 8 Accessory Board ALM Dimensions (H x W x L) H = 2.3 mm (.81 in.); W = 3 mm (1.18 in.); L = 133 mm (.24 in.) X.2 THRU X X araya Logic Module with DALI Accessory Board and Cover Dimensions outside parentheses are in millimeters. Dimensions within parentheses are in inches. The mounting holes are mm in diameter. 8.2 Mechanical Specifications (DALI Type 8 Accessory Board) Lumenetix part #: Wire Specifications: AWG, solid wire or tin-dipped stranded Connector: TE X DALI Accessory Board All dimensionss are in millimeters. 14 Logic Module with Revised Specifications subject to change without notice

15 8 DALI TYPE 8 ACCESSORY BOARD Maximum Peak Lumens 8.3 Mounting Specifications (DALI Type 8 Accessory Board) The Accessory Board is mounted on the 1-pin header and located on the two bosses, and then captured in place to the ALM with two (2) self-tapping screws. Screw Specifications: Phillips Rounded Head Thread-Forming Screws for Plastic, 18-8 Stainless Steel, Number 4 Size, 1/8" Long; McMasterCarr # 99461A1. Torque Specifications: 2. to 2. in-lb CAUTION: The screws are very small and are self-threaded into small plastic bosses. Overtorquing will strip the plastic and damage the ALM housing. 1 Logic Module with Revised Specifications subject to change without notice

16 9 HEAT SINKING RECOMMENDATIONS Maximum Peak Lumens The Dynamic Dimming Module requires an external heat sink in order to ensure proper operating temperature of the LEDs. The DDM has a conductive aluminum case and an efficient thermal path to the LED array. These features promote efficient thermal management and allow for a simple heat sink design in most applications. Examples of heat sinking methods are cast or extruded heat sinks. Both carbon and stainless steel are much less efficient at transferring heat than aluminum and therefore are not recommended as heat sink materials. The heat sink mounting surface should be flat and smooth. Metal-to-metal contact surfaces will result in best performance; anodized or unfinished mounting surfaces are recommended. Mounting the DDM on a painted aluminum surface will reduce the performance of the heat sink material. In many fixtures, the air flow to the heat sinks is obstructed or the heat sink is in an enclosed container with no path to reject heat. The thermal design of the fixture must be optimized so that the maximum temperature is less than the Tc max (maximum case temperature) as indicated in the drawings in the following section. If the Tc max is exceeded in the application, the junction temperature of the LEDs will be higher than that required to meet the L7 life, and the Lumenetix warranty will be void. IMPORTANT: Most heat sinks are qualified in free air at an approximate ambient temperature of 2 C. If the DDM is installed in an insulated can fixture (IC Can), the module may exceed the recommended operating temperature. The heat sink must be evaluated and temperature tested in the fixture at applicable ambient temperatures for the desired application. 16 Logic Module with Revised Specifications subject to change without notice

17 Maximum Peak Lumens 1 CASE TEMPERATURE MEASUREMENT POINTS 1.1 Logic Module (ALM) Case Temperature (Tc) Measurement Points MAXIMUM CASE TEMPERATURE (Tc) FOR ALM: 7 C 1.2 Round LED Array Case Temperature (Tc) Measurement Point Maximum Case Temperature (Tc) for Round LED Array: 9 C UL Recognized Component Dry or ry Damp or Damp Locations Location Class 2 Input Class 2 Input 17 Logic Module with Revised Specifications subject to change without notice

18 11 SECONDARY OPTICS Maximum Peak Lumens 11.1 Attaching Compatible Reflectors for Round LED Arrays The round LED arrays with 19mm LES (Light Emitting Surface) accept twist-to-lock reflectors with an attachment collar. The fastener specifications are shown in the following table while mounting hole locations are shown in Figures 1, 2 and 3. Secondary Optics Fastener Specifications Attachment Type Fastener specifications Screw length Notes Twist-Lock (with Adaptor Ring) M3 x 6; quantity of two 6 mm (1/4 ) Pan head screws Twist-Lock (with Adaptor Ring & Adaptor) M3 x 6; quantity of two 6 mm (1/4 ) Pan head screws TE Type 2 Clip M3 x 1; quantity of two 1 mm (3/8 ) Rounded head screws Figure 1: Round LED Array with XSA-242 Adaptor Ring (by Xicato) Figure 2: Round LED Array with XSA-242 Adaptor Ring (by Xicato) with Adaptor, used for Reflectors by Diffractive Optics (p/n: P148) or Khatod (p/n: KE19W) Figure 3: Round LED Array with Lumawise Z Type 2 Clip (by TE) 18 Logic Module with Revised Specifications subject to change without notice

19 11 SECONDARY OPTICS Maximum Peak Lumens Compatible Reflectors List (DDM 219) Compatible Reflectors for 19mm LES round LED arrays (continued on next page) Manufacturer M. Part Number beam angle (deg) outer dim (mm) height (mm) optical finish optical finish 2 attach method Diffractive Optics P1332 (XSA-22) 4 29 specular none XSA242 Diffractive Optics P134 (XSA-221) specular faceted XSA242 Diffractive Optics P138 (XSA-223) specular none XSA242 Diffractive Optics P131 (XSA-224) specular none XSA242 Diffractive Optics P1316 (XSA-227) specular faceted XSA242 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular superfacet, diamond XSA242 + P148 Diffractive Optics P specular faceted XSA242 + P148 Diffractive Optics P specular faceted XSA242 + P148 JORDAN specular super facet none JORDAN specular super facet none Khatod EASY KCLP 188CR combination none Zhaga Screw 3mm Khatod EASY KCLP 188ME honeycomb lens none Zhaga Screw 3mm Khatod EASY KCLP 188WI 72 2 bugeye lens none Zhaga Screw 3mm Khatod EASY KCLP 189CR combination none Zhaga Screw 3mm Khatod EASY KCLP 189ME honeycomb lens none Zhaga Screw 3mm Khatod EASY KCLP 189WI bugeye lens none Zhaga Screw 3mm Khatod EASY KCLP 1799 CR asym specular none Zhaga Screw 3mm Khatod KCLP 1682 CR (1429CR) specular none TE Type II / XSA242 + KE19W Khatod KCLP 1682 ST (1429ST) diffuse none TE Type II / XSA242 + KE19W khatod KCLP 1683 CR (143CR) specular none TE Type II / XSA242 + KE19W khatod KCLP 1683 ST (143ST) diffuse none TE Type II / XSA242 + KE19W khatod KCLP 1431 CR 6 3 specular none TE Type II / XSA242 + KE19W khatod KCLP 1432 CR 6 3 specular none TE Type II / XSA242 + KE19W khatod KCLP 168 ST (1432ST) diffuse none TE Type II / XSA242 + KE19W khatod KCLP 1684 ST diffuse none TE Type II / XSA242 + KE19W khatod KCLP 1686 CR specular none TE Type II / XSA242 + KE19W khatod KCLP 1687 CR specular none TE Type II / XSA242 + KE19W khatod KCLP 1687 ST diffuse none TE Type II / XSA242 + KE19W khatod KCLP 1688 CR specular none TE Type II / XSA242 + KE19W khatod KCLP 1688 ST diffuse none TE Type II / XSA242 + KE19W khatod KCLP 1689 ST diffuse none TE Type II / XSA242 + KE19W khatod KCLP 169 ST 6 3 diffuse none TE Type II / XSA242 + KE19W khatod KCLP 1691 ST diffuse none TE Type II / XSA242 + KE19W khatod PLJT 1866 n/a diffuse ball XSM242 NOTE: Reflectors have been recommended based on independent optical tests conducted by Lumenetix, and should be used as guidelines. Final reflector evaluation should be made by fixture manufacturers with all optics in place. 19 Logic Module with Revised Specifications subject to change without notice

20 11 SECONDARY OPTICS Maximum Peak Lumens Compatible Reflectors List (DDM 219) Compatible Reflectors for 19mm LES round LED arrays (continued from previous page) Manufacturer M. Part Number beam angle (deg) outer dim (mm) height (mm) optical finish optical finish 2 attach method Nata 399-E diffuse super facet none Nata 3991-E diffuse super facet none Nata 3993-E 4 8. diffuse super facet none Nata 2-1A satin none XSA242 Nata E m-diffuse facets XSA242 Nata E m-diffuse super facet XSA242 Nata E m-diffuse super facet, flare XSA242 Nata 4-11E m-diffuse super facet none Nata 4-14E specular facets none Nata 4-146E diffuse super facet none Nata 2-13E m-diffuse super facet none Nata 4-136E m-diffuse super facet none Nata 4-137E diffuse super facet none Nata E m-diffuse super facet none / 3 tabs Nata E diffuse super facet none / 3 tabs Nata E m-diffuse super facet none Nata 4-182E diffuse super facet none / 3 tabs Nata 3-191M m-diffuse super facet XSA242 Nata 3-193M m-diffuse super facet XSA242 Nata E m-diffuse super facet XSA242 Widegerm 19T-XC specular faceted XSA242 Widegerm 11T-XC 3. specular none, trumpet XSA242 Widegerm 28x-XM satin lightfaceted XSA242 Widegerm 221T-XM m-diffuse faceted XSA242 Widegerm 222T-XM m-diffuse faceted XSA242 Widegerm 31T-XM m-specular faceted XSA242 Widegerm 324T-XM m-diffuse faceted XSA242 Widegerm 32T-XM specular faceted XSA242 Widegerm 327T-XC satin none XSA242 Widegerm 4219T-XM diffuse faceted XSA242 Widegerm 422T-XM m-specular faceted XSA242 Widegerm 4221T-XM m-specular faceted XSA242 Widegerm 431T-XM m-diffuse faceted XSA242 Widegerm 441T-XM m-diffuse faceted XSA242 NOTE: Reflectors have been recommended based on independent optical tests conducted by Lumenetix, and should be used as guidelines. Final reflector evaluation should be made by fixture manufacturers with all optics in place. 2 Logic Module with Revised Specifications subject to change without notice

21 11 SECONDARY OPTICS Maximum Peak Lumens Compatible Reflectors List (DDM 232) Compatible Reflectors for 32mm LES round LED arrays Manufacturer M. Part Number beam angle (deg) outer dim (mm) height (mm) optical finish optical finish 2 attach method Jordan specular super facet none Jordan specular super facet none Nata 4-11E m-diffuse super facet none Nata 4-136E m-diffuse super facet none Nata E diffuse super facet none / 3 tabs Nata E m-diffuse super facet none Nata 4-182E diffuse super facet none / 3 tabs NOTE: Reflectors have been recommended based on independent optical tests conducted by Lumenetix, and should be used as guidelines. Final reflector evaluation should be made by fixture manufacturers with all optics in place. 21 Logic Module with Revised Specifications subject to change without notice

22 12 RIBBON CABLE ASSEMBLIES Maximum Peak Lumens 12.1 Jacketed / Round 16-Pin Ribbon Cable (Nominal 18 Length) Lumenetix part #: pin Tyco Connector at one end, 2-pin JST connector at other end; for connecting ALM to round array. 1 3 RED WIRE GOES TO PIN 3 OF THE 2 PIN JST CONNECTOR MAX MAX 47 2 Note: All dimensions are in millimeters. ITEM NO. PART NUMBER DESCRIPTION QTY PIN CONNECTOR CONNECTOR 16 PIN CRIMP SSH-3T-PO.2-H M ROUND JACKED FLAT CABLE M ROUND JACKED FLAT CABLE 379/ CONNECTOR SHR-2V-S-B CONNECTOR SHR-2V-S-B 1 6 LABEL, LUMENETIX, PART#, DESCRIPTION, REVISION LUMENETIX, P/N, DESCRIPTION, REVISION 1 22 Logic Module with Revised Specifications subject to change without notice

23 12 RIBBON CABLE ASSEMBLIES Maximum Peak Lumens 12.2 Flat 16-Pin Ribbon Cable (Nominal 18 Length) Lumenetix part #: pin Tyco Connector at one end, 2-pin JST connector at other end; for connecting ALM to round array CUT CABLE FLUSH TO CONNECTOR +/-. 16 PIN CABLE 2 PIN JST CONNECTOR 47 2 RED WIRE IS PIN 1 RED WIRE GOES TO PIN 3 OF THE 2 PIN JST CONNECTOR Note: All dimensions are in millimeters. NO. 1 LABEL, LUMENETIX, PART#, DESCRIPTION, REVISION PIN RIBBON CABLE 3M PIN CONNECTOR c t-3d CONNECTOR SHR-2V-S-B 1 CRIMP SSH-3T-PO Logic Module with Revised Specifications subject to change without notice

24 13 POWER / CONTROL CABLE ASSEMBLIES Maximum Peak Lumens Power Cable Assembly (Nominal 24 Length) Provides power to each module. Lumenetix part #: X STRIP AND TIN Note: All dimensions are in millimeters. ITEM NO. PART NUMBER DESCRIPTION QTY. 1 RED WIRE 24AWG HOOK -UP WIRE STRANDED 7/32 24AWG RED 1 2 BLACK WIRE 24AWG HOOK -UP WIRE STRANDED 7/32 24AWG BLACK 1 3 CONNECTOR MOLEX CRIMP MOLEX Pin Allocation Chart for Power Cable Assembly Pin # Lead Color Input Pin 1 Red Power 24V DC (+) Pin 2 Black Power Common (-) 24 Logic Module with Revised Specifications subject to change without notice

25 13 POWER / CONTROL CABLE ASSEMBLIES Maximum Peak Lumens Control Cable Assembly (Nominal 24 Length) Provides -1V control and RS-48 signals to each module. Lumenetix part #: X STRIP AND TIN ± ITEM NO. PART NUMBER DESCRIPTION QTY MOLEX CONNECTOR CRIMP 7 3 VIOLET WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG VIOLET 1 4 BLUE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG BLUE 1 ORANGE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG ORANGE 1 6 WHITE WITH ORANGE STRIPE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG WHITE WITH ORANGE STRIPE 7 BROWN WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG BROWN 1 8 GREY WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG GREY 1 9 WHITE WIRE 24AWG HOOK-UP WIRE STRANDED 7/32 24AWG WHITE 1 1 Note: All dimensions are in millimeters Pin Allocation Chart for Control Cable Assembly Pin # Lead Color Input Pin 1 Violet -1V Dimming (+) Pin 2 Blue -1V Color (+) Pin 3 Orange Digital Data - (NOT USED) Pin 4 White with orange stripe Digital Data + (NOT USED) Pin Brown Digital Common (NOT USED) Pin 6 Gray -1V Dimming (-) Pin 7 White -1V Color (-) 2 Logic Module with Revised Specifications subject to change without notice

26 14 WIRING DIAGRAMS Maximum Peak Lumens V Best Wiring Practice Any manufacturer that makes a dimmer that sinks will work with Lumenetix modules since we source the voltage. -1V is a topology defined by the International Electrotechnical Commission (IECR) 6929 Annex E standard and uses a varying DC voltage between 1 and 1V to determine the lighting level. The fixture outputs a minimum light level below 1V w hich is defined as low-end. Between 1 and 1V, t h e signal corresponds to levels between the minimum and maximum output level. A signal above 1V corresponds to the maximum light level. Sometimes it is referred to as 1-1V, as that is the actual range in which the light levels will vary. Each dimmer will have their own distinct dimming profile. Best practice is to limit the distance run for the analog control wiring from the controller to the last driver to 3. This is based on 18 AWG wire. It is possible to extend the run to 4 by using 16 AWG wire, but that should be considered carefully as an exception to best design practice. Whenever any part of the control circuit (the driver, dimer, or wire used) is designed for use in a Class 2 installation, it is critical that the entire control circuit be kept separate from Class 1 line voltage wiring per the requirement of National Electric Code, section The electrical drawings must be very clear that class 1 and class 2 wiring cannot be combined. There must be separation because: a) it is possible for higher voltage wiring to induce an AC voltage in to the low voltage signal wiring; and, b) undesirable visual artifacts in the dimmed lighting can be caused when the line and low voltage wiring is run together (especially for long distances). We do not recommend installing the low voltage signal wiring in the same conduit or raceway as line voltage wiring even when all elements of the control circuit are listed for Class 1 wiring methods. NOTE: Lumenetix modules operate between 1-1V. All dimmers that have minimum and maximum trim pots should be set at a minimum of 1 volt and a maximum of 1 volts, measuring the voltage at the end of the line. -1V Dimmers (recommended list)* Crestron ETC Fresco Legrand Leviton Lutron Nexlight N-Light Pass & Seymour Vantage Wattstopper *Recommendations are subject to change. Consult your Lumenetix representative for the most updated list. 26 Logic Module with Revised Specifications subject to change without notice

27 14 WIRING DIAGRAMS Maximum Peak Lumens V Wiring Diagram INDEX TAB ON RED END OF CABLE CONNECTOR SHOULD LINE UP WITH INDEX SLOT ON ALM. TUNABLE COLOR ROUND LED ARRAY FIXTURE RIBBON CONNECTOR CABLE MAKE SURE TO ALIGN INDEX TAB TO INDEX SLOT. ALM 7-WIRE CONTROL CABLE ( ) VIOLET (+) -1V CONTROLLER (DIM) GRAY (-) DIGITAL WIRES (ORANGE / WHITE WITH ORANGE STRIPE / BROWN) SHOULD REMAIN OPEN BLUE (+) -1V CONTROLLER (CCT) WHITE (-) BLACK (Common) CLASS-2 AC TO DC 24V POWER SUPPLY RED (+) (SUPPLIED BY OEM) JUNCTION BOX WHITE (NEUTRAL) BLACK (HOT) araya LOGIC MODULE (ALM) ALM 24V POWER CABLE ( ) LINE-IN VOLTAGE (REFER TO POWER SUPPLY) The Constant Hot/Live must not be wired to a switching device. 27 Logic Module with Revised Specifications subject to change without notice

28 14 WIRING DIAGRAMS Maximum Peak Lumens 14.2 Bluetooth Operation using the Tunable Color 2. ios App TUNABLE COLOR ROUND LED ARRAY FIXTURE TUNABLE COLOR 2. ios APP (MAX. OF 8 MODULES CAN BE COMMISSIONED AT A TIME) RIBBON CONNECTOR CABLE MAKE SURE TO ALIGN INDEX TAB TO INDEX SLOT. JUNCTION BOX BLACK (Common) RED (+) CLASS-2 AC TO DC 24V POWER SUPPLY (SUPPLIED BY OEM) WHITE (NEUTRAL) BLACK (HOT) araya LOGIC MODULE (ALM) ALM 24V POWER CABLE ( ) LINE-IN VOLTAGE (REFER TO POWER SUPPLY) The Constant Hot/Live must not be wired to a switching device. This may be put on a relay for maintenance. NOTE: BLUETOOTH OPERATION IS FOR COMMISSIONING THE MODULES ONLY, NOT FOR CONTROLLING THEM. 28 Logic Module with Revised Specifications subject to change without notice

29 14 WIRING DIAGRAMS Maximum Peak Lumens 14.3 DMX12-A-RDM Protocol DMX12-A is an acronym for Digital Multiplex, a communication protocol used to remotely control lighting dimmers and intelligent fixtures. It is designed to provide a common communications standard between these lighting devices regardless of the manufacturer. The 12-A after the DMX refers to the number of control channels used on one network segment (often called a universe ) of devices. In a simple dimming system, one channel controls the intensity of the fixture. A single intelligent fixture such as the araya requires several channels to control its various parameters (one channel each for DIM, CCT, SAT, HUE). DMX12A Specifications: DMX 12-A (Controller). A universe is 12 Channels. DMX value is between and 2, where is off and 2 is full on. The maximum number of devices in a daisy-chain wire run is 32, which include the controller and opto-splitter. The maximum network wire run is a distance of up to 16 feet for non-rdm systems and up to 1 feet for RDM systems. One device functions as the master (DMX controller) on a network, while the rest function as slaves (mergers, splitters, intelligent fixtures, etc.). Only the controller (master) transmits over the network, and all fixtures receive the same data. The final device in the daisy-chain must be terminated with a 12 ohm resistor between DMX+ and DMX- pins. It is recommended that the terminator for the final device be located in the control panel, if it falls within the recommended wiring distance. All wiring must be in a continuous run and daisy-chained. Star wiring is only allowed in conjunction with an opto-splitter. Do not run DMX control cable in close proximity to AC power lines. EM spikes from switching of high-current devices such as HVAC equipment or generators will induce noise into the DMX cable. The shield must be carried through between modules and properly grounded at one point only. Connections to DMX12-A-RDM accessory board: wire size to be 24AWG, and solid or stranded cables may be used. Stranded wire used must be tinned or installed with ferule connector. RDM DMX12-A control protocol that enables Remote Device Management for two-way communications for configuration, monitoring and system setup. Allows two way communication between lighting controller and the fixtures. Allows for remote setting of DMX start addressing. RDM signals are sent back the other way, but not constantly. Controller can ask one or more devices for query feedback. RDM packets are inserted in-between the existing DMX data packets being used to control the lighting. The DMX Control Console will broadcast up to 12 channels over one DMX cable (max. run of 1 feet for RDM). Some of these channels may not be used, but will still be transmitted, as required by the protocol. It must be set to a desired channel (1, , etc.) to control the connected light fixture. This is usually accomplished using RDM. This desired channel is commonly known as the DMX address. When addressing fixtures, it is not recommended to skip addresses. When RDM is not available with the control system, it is permissible to use the Lumenetix commissioning tool (the araya Tunable Color 2. ios App) to set the address of the slots. The instructions to configure the DMX channels can be found in the separate araya Tunable Color Instruction Manual. The DMX12-A interface follows the ANSI E (R2113) standard. Four address slots are allocated to each interface board and control the Dim level, CCT, Saturation and Hue of the araya modules connected to the board. Default DMX12-A Slot Allocation: Slot Function 1 Dim Level 2 CCT 3 Saturation Level 4 Hue 29 Logic Module with Revised Specifications subject to change without notice

30 14 WIRING DIAGRAMS Maximum Peak Lumens DMX12-A Electrical Specifications Parameter Range Remarks ESD Protection ±1KV (air), ±8KV (conducted) Per IEC Termination Recommended The DMX12 bus termination rules apply Directionality Receive only Frequency stability ±2ppm Load per port 1/26 1/8 of Nominal RS-48 Isolation 3KVrms DMX12-A Control Systems (recommended list) Choreo Cognito Crestron Greenlight System Entec ETC Mosaic ETC Paradigm Fresco Lutron HomeWorks QS Lutron Quantum Nicolaudie Pathway Connectivity Pharos Traxon Ecue Vantage Controls *Recommendations are subject to change. Consult your Lumenetix representative for the most updated list. 3 Logic Module with Revised Specifications subject to change without notice

31 14 WIRING DIAGRAMS Maximum Peak Lumens DMX12-A Recommended Field Wiring Liberty 24-2P-48 (Non-Plenum), 24 AWG, 2 pair dual 12 ohm, 11.2 pf/ft low capacitance (Wago, XLR and PHX connectors) Liberty 24-2P-P48 (Plenum), 24 AWG, 2 pair dual 12 ohm, 11.2 pf/ft low capacitance (XLR and PHX connectors) Belden #9842 (Non-Plenum), 24 AWG, 2 pair dual shielded 12 ohm, 12.8 pf/ft low capacitance (XLR and PHX connectors) Belden #89842 (Plenum), 24 AWG, 2 pair dual shielded 12 ohm, 12.8 pf/ft low capacitance (XLR and PHX connectors) Please refer to wire manufacturer s lighting catalog for and/equals as required by code. Category Wire or Equal The Entertainment Services and Technology Association (ESTA) does not define a maximum run length for DMX over Cat since many factors will affect the maximum run length, such as number of devices, number of splices in the cable, the strength of the DMX transmitter(s), if Remote Device Management (RDM) is being used, and sources of interference. ESTA does state (again, in ANSI E1.21-2): A properly selected and installed DMX12 cable should provide acceptable signal strength for runs of 3m (1ft). Please note that the technical requirements, such as run-length and topology for other networking technologies, such as Ethernet, should be considered if using the installed cable for another networking technology in the future is anticipated. Cat or equivalent is not preferred as a portable cable since it is not as rugged as other DMX cables. Male RJ4 connectors are especially prone to breakage over repeated re-connections. LUMENETIX RECOMMENDATION: CAT E -1 FEET CRESTRON DM-CBL-8G-NP DM-CBL-8G-P CAT 7-33 FEET CRESTRON DM-CBL-ULTRA-NP DM-CBL-ULTRA-P DMX12-A Recommended Field Connectors (or Equal) WAGO 221 PHOENIX CONTACT XLR NEUTRIK CRESTRON RJ4 DM -8G-CONN RJ4 IDC DM-CONN DMX12-A Wiring Connections Signal Description Pin Colors (4-Pair Cable) Pin Colors (2-Pair Cable) 3-pin XLR connector -Pin XLR connector Signal Common White/Brown and Brown White/Blue and Blue Data (-) Primary Data Link Orange Orange Data (+) Primary Data Link White/Orange White/Orange Data2 (-), or not used Optional Secondary Data Link 4 4 Data2 (+), or not used Optional Secondary Data Link -Pin PHX connector XLR Connectors (-Pin) RJ-4 Connector Pin-Out (T68B) Logic Module with Revised Specifications subject to change without notice

32 14 WIRING DIAGRAMS Maximum Peak Lumens DMX12-A Controller Example DMX Loop 1 DMX Loop 2 Up to 3 devices on each loop 12 / 23 V~ Control Power DMX Controller RDM Merger / Splitter Wallstation Bus Power Module Processor Contact Closure Interface Touch Panel total devices Shade / Drapery *Fixture refers to a luminaire with one Lumenetix module, and with one address (DDM) or four addresses (CTM). Power Supply DMX12-A Drain Wire Connections Drain wire connections are required as follows. Shielding To add another level of protection from electromagnetic noise, a grounded shield is added over the twisted pair wires. When this is enclosed in a protective jacket, to avoid ground loops and electromagnetic contamination of the ground system, all control ground wiring, including cable shields and drain wires, should be treated like sensitive current-carrying conductors. All control ground wires should be insulated (not bare) and the same wiring practices should be observed with ground wires as with other sensitive signals. Care must also be taken when designing control wiring to ensure that each shield is connected to only a single ground point. You should establish this point at a central location, like a control panel or cabinet, and avoid all connection to grounds in the field. A control ground is sometimes referred to as an isolated ground (an oxymoron) for this reason, but the term single-point ground is more accurate. Method-1 A typical two-pair shielded cable can be prepared for termination to the terminals with the drain wire cut off. This is usually done at the field end of the cable where no shield grounding is desired. You will then use insulating tape or heat-shrink tubing to protect the cable from contamination and to prevent accidental grounding of the shield or drain wire. An accidental ground at this point would almost certainly create an undesirable ground loop. Method-2 A typical two-pair shielded cable can be prepared for termination to the terminals with the drain wire cut off. The drain wire, which is an uninsulated conductor, is sleeved with a insulating tubing to prevent accidental grounding. The crimp-on lug is valuable in this instance to retain the tubing. Insulating tape or heat-shrink tubing is again used to protect the cable from contamination and to prevent accidental grounding, since any accidental connection between the drain wire and a chassis, frame, or enclosure would almost certainly create a ground loop. 32 Logic Module with Revised Specifications subject to change without notice

33 14 WIRING DIAGRAMS Maximum Peak Lumens DMX12-A-RDM Accessory Card Wiring Diagram Notes: 1. 24V power (red/black) is Class-2 rated. 2. Adapter is configured at factory for DMX inputs. TUNABLE COLOR ROUND LED ARRAY FIXTURE DMX SLOTS SET BY RDM OR BY TUNABLE COLOR 2. ios APP (MAX. OF 8 MODULES CAN BE COMMISSIONED AT A TIME) RIBBON CONNECTOR CABLE MAKE SURE TO ALIGN INDEX TAB TO INDEX SLOT. DMX wiring provided by others. JUNCTION BOX DMX IN DMX OUT DMX12A CONTROLLER COMMON DATA (-) DATA (+) COMMON DATA (-) DATA (+) araya LOGIC MODULE (ALM) DMX12-A-RDM accessory board connects to an electrically isolated expansion port within the ALM. BROWN ORANGE WHITE WITH ORANGE STRIPE BLACK (Common) RED (+) ALM 24V POWER CABLE ( ) CLASS-2 AC TO DC 24V POWER SUPPLY (SUPPLIED BY OEM) WHITE (NEUTRAL) BLACK (HOT) LINE-IN VOLTAGE (REFER TO POWER SUPPLY) The Constant Hot/Live must not be wired to a switching device. This may be put on a relay for maintenance. NOTE: BLUETOOTH OPERATION IS FOR COMMISSIONING THE MODULES ONLY, NOT FOR CONTROLLING THEM. 33 Logic Module with Revised Specifications subject to change without notice

34 14 WIRING DIAGRAMS Maximum Peak Lumens 14.4 Lutron EcoSystem Protocol EcoSystem technology is a control method for LEDs that provides addressing of individual fixtures and status feedback. This makes it easy to digitally assign one or many fixtures without complicated wiring. This opens up an entire suite of energy-saving, system-monitoring and system-control schemes where the design, setup and rezoning are all done within software, making the electrical and control design simple. The modules attached to different interface boards can be controlled independently or assigned to a single group by the EcoSystem controller. The EcoSystem control is responsible for saving any configuration settings. Once an interface board is assigned a pair of addresses, assigned addresses are saved in NVRAM. During the EcoSystem discovery process, the user pairs the desired dimming control in the controller to the Dim channel address in the interface board. The same applies for the CCT channel. 1 pair 16AWG Eco Loop, 9 feet (field wiring). Maximum of 64 addresses on each loop. EcoSystem Control Systems (recommended list)* Quantum System HomeWorks QS Grafik Eye QS Control Unit with EcoSystem EnergiSavr Node with EcoSystem Power Module with EcoSystem *Recommendations are subject to change. Consult your Lumenetix representative for the most updated list. Lutron EcoSystem Controller Example Lutron EcoSystem Example Power Eco Loop 1 Eco Loop 2 QS Link Fixture* Up to 64 devices on each loop for Eco-1, and up to 32 devices on each loop for Eco-2 HomeWorksR QS Power GRAFIK Module with Module Processor 12 / 23 V~ EyeR QS Control Power Up to 1 EcoSystem HomeWorksR QS Wallstation SivoiaR QS Shade / Drapery Fixture* Fixture* Fixture* QS Contact Closure Interface total QS devices *Fixture refers to a luminaire with one Lumenetix module, and with one address (DDM) or two addresses (CTM). QS Power Supply 34 Logic Module with Revised Specifications subject to change without notice

35 14 WIRING DIAGRAMS Maximum Peak Lumens Lutron EcoSystem Field Wiring EcoSystem Digital Loop can be wired as Mains voltage or IEC PELV/NECR Class 2 for maximum wiring flexibility.. The Loop is polarity insensitive and can be wired in any topology.. Consult all national and local electrical codes for separation requirements.. Wire Gauge Maximum EcoSystem-Compliant Loop Wire Length 4. mm 2 (12 AWG) 671 m (22 ft) 2. mm 2 (14 AWG) 427 m (14 ft) 1. mm 2 (16 AWG) 27 m (9 ft) 1. mm 2 (18 AWG) 17 m (7 ft) Drain Wire Connections Drain wire connections are required as follows. Shielding To add another level of protection from electromagnetic noise, a grounded shield is added over the twisted pair wires. When this is enclosed in a protective jacket, to avoid ground loops and electromagnetic contamination of the ground system, all control ground wiring, including cable shields and drain wires, should be treated like sensitive current-carrying conductors. All control ground wires should be insulated (not bare) and the same wiring practices should be observed with ground wires as with other sensitive signals. Care must also be taken when designing control wiring to ensure that each shield is connected to only a single ground point. You should establish this point at a central location, like a control panel or cabinet, and avoid all connection to grounds in the field. A control ground is sometimes referred to as an isolated ground (an oxymoron) for this reason, but the term single-point ground is more accurate. Method-1 A typical two-pair shielded cable can be prepared for termination to the terminals with the drain wire cut off. This is usually done at the field end of the cable where no shield grounding is desired. You will then use insulating tape or heat-shrink tubing to protect the cable from contamination and to prevent accidental grounding of the shield or drain wire. An accidental ground at this point would almost certainly create an undesirable ground loop. Method-2 A typical two-pair shielded cable can be prepared for termination to the terminals with the drain wire cut off. The drain wire, which is an uninsulated conductor, is sleeved with a insulating tubing to prevent accidental grounding. The crimp-on lug is valuable in this instance to retain the tubing. Insulating tape or heat-shrink tubing is again used to protect the cable from contamination and to prevent accidental grounding, since any accidental connection between the drain wire and a chassis, frame, or enclosure would almost certainly create a ground loop. 3 Logic Module with Revised Specifications subject to change without notice

36 14 WIRING DIAGRAMS Maximum Peak Lumens Dynamic Tunable Dimming Color Round LED Arrays CTM Lutron EcoSystem Accessory Card Wiring Diagram Notes: 1. 24V power (red/black) is Class-2 rated. 2. EcoSystem Channel 1 is always Intensity control. EcoSystem Channel 2 is always CCT control. 3. In the EcoSystem programming mode, EcoSystem Channel 1 controls the intensity from 1%-1%. EcoSystem Channel 2 controls the CCT range from 16-8K. 4. The araya Tunable Color 2. ios App should be turned on, and the DMX channels should be set to 2, 4, 6, 8. TUNABLE COLOR ROUND LED ARRAY FIXTURE RIBBON CONNECTOR CABLE MAKE SURE TO ALIGN INDEX TAB TO INDEX SLOT. ALM WITH LUTRON ACCESSORY BOARD Fixture manufacturer to provide minimum 18 AWG of Lutron EcoSystem wire tail (labeled E1 and E2) to junction box. Consult Lutron for field wiring. WHITE / VIOLET STRIPES VIOLET LUTRON ECOSYSTEM CONTROLLER E2 E1 BLACK (Common) RED (+) ALM 24V POWER CABLE ( ) CLASS-2 AC TO DC 24V POWER SUPPLY (SUPPLIED BY OEM) JUNCTION BOX WHITE (NEUTRAL) BLACK (HOT) LINE-IN VOLTAGE (REFER TO POWER SUPPLY) EcoSystem accessory board connects to an electrically isolated expansion port within the ALM The Constant Hot/Live must not be wired to a switching device. This may be put on a relay for maintenance. 36 Logic Module with Revised Specifications subject to change without notice

37 14 WIRING DIAGRAMS Maximum Peak Lumens 14. DALI Type 8 Protocol Specifications Digital Addressable Lighting Interface (DALI) is a communication language. DALI facilitates the communication and therefore control of multiple devices such as drivers, transformers and other lighting equipment. Devices which speak the same language can exchange information, in much the same way people can exchange information when they communicate using the same language. DALI Devices: Designed on a distributed intelligent framework, each DALI device has on-board memory that stores all relevant information about the device, including diagnostics, which reduces the technical requirements on the control system and the amount of data to be transmitted over the line. DALI Standards: DALI is a lighting control standard defined under the European Standard IEC IEC stands for International Electrotechnical Commission and is a non-profit organization. DALI was designed to replace traditional 1-1 V analog systems and proprietary digital systems such as DSI (Digital Serial Interface). At a maximum there can be 64 DALI devices on a single DALI line and it has a data baud rate of 12 baud. DALI Technical Specifications: Numbers of units: max. 64 Numbers of addresses: 64 Signal level: +/- 16V Cable length: max. 3m, and less than 2V voltage drop Cable type: any 2 wire unshielded cable Cable topology: any (line, star, tree, ring) Refresh rate: max 4 messages / second +/- 12 baud Safety DALI is not SELV; cable must be treated like mains wiring Maximum DALI-compliant Bus Wire Length: 1. mm 2 (3 m).7 mm 2 (1 m). mm 2 (1 m) A DALI system contains one current source, a controller and input(s). In idle state the current signal is high so there is current. A driver input current is 2mA in idle state. Nominal current for 64 inputs is 128mA. Information is transferred by short circuiting the current, (controller / input). Communication is always started by the controller. An input can only answer (=back channel info). Random addressing is possible. DALI units have no address from factory. Any address can be changed via the DALI connection. An input can detect if the DALI current is present. 37 Logic Module with Revised Specifications subject to change without notice

38 14 WIRING DIAGRAMS Maximum Peak Lumens DALI Type 8 Wiring Specifications DALI Wiring can be run up to 3m using 1.mm cable. (1 awg) The DALI specification allows for maximum 2V drop in the communication signal. The DALI line does not require termination of the line and supports all wiring typologies except rings and closed loops (trees, branches and chains are all acceptable). The following are National Electric Code (NEC 7) requirements. DALI Class 1 and Class 2 Wiring Overview: DALI dimming ballasts and drivers are connected together by a 2-wire low voltage bus that is suitable for Class 1 or Class 2 wiring installations. This application note explains how both Class 1 and 2 wiring are made and how they both meet National Electric Code (NEC) regulations. DALI Dimming Ballast and Driver Wired Class 2: For more information on Class 2 wiring and additional Class 2 wiring requirements see National Electric Code Article 72. With regards to factory installed wiring, as per UL198 section : Factory-installed power limited wiring and branch circuit wiring that come in random contact within the luminaire shall have insulation rated for the maximum voltage that exists in any of the circuits. If wiring with the properly rated insulation is used, then no spacing or separation is required regardless of the circuit conductor voltage although shielding may be required. Class 2 wiring of the DALI dimming ballast and driver follows the NEC Requirement (D) (references to Class 3 are eliminated). Class 2 circuit conductors in compartments, enclosures, device boxes, outlet boxes, or similar fittings shall be permitted to be installed with electric light, power, Class 1 circuits where they are introduced solely to connect the equipment connected to Class 2 circuits and where (1) or (2) applies: 1. The electric light, power, Class 1 circuit conductors are routed to maintain a minimum of 6 mm (.2 in) separation from the conductors and cables of Class The circuit conductors operate at 1 volts or less to ground and also comply with one of the following: A. The Class 2 circuits are installed using Type CL3, CL3R, or CL3P or permitted substitute cables provided these Class 3 cable conductors extending beyond the jacket are separated by a minimum of 6 mm (.2 in) or by a nonconductive sleeve or nonconductive barrier from all other conductors. B. The Class 2 circuit conductors are installed as a Class 1 circuit. The DALI dimming ballast and driver have a minimum spacing of.2 inches between line voltage and the bus terminals (purple and grey wires) for Class 2 installations. DALI Bus Wired Class 1: Class 1 wiring methods follow the NEC Requirement Class 1 circuits shall be permitted to be installed with other circuits as specified in (A) and (B): A. Class 1 circuits shall be permitted to occupy the same cable, cable tray, enclosure, or raceway without regard to whether the individual circuits are alternating or direct current, provided all conductors are insulated for the maximum voltage of any conductors in the cable, cable tray, enclosure or raceway. B. Class 1 circuits shall be permitted to be installed with power supply conductors as specified: 1. Class 1 and power supply circuits shall be permitted to occupy the same cable, enclosure, or raceway only when functionally associated. Since the DALI dimming ballast and driver meets Class 2 installation requirements, it can also be installed in a Class 1 configuration when Class 2 markings are not present. The NEC allows the reclassification of Class 2 circuits per Article Exception No.2: Class 2 and circuits shall be permitted to be reclassified and installed as Class 1 circuits if the Class 2 markings are eliminated and the entire circuit is installed using the wiring methods and materials in accordance with Part II, Class 1 circuits. Note: For more information regarding Class 2 wiring and additional requirements see the National Electrical Code Article 72. Reference Information: Code quotation, guidance, and wiring guides above are listed for reference only. Always follow local and national wiring requirements. NEC 28 was used as a reference in this Application Note. More recent releases of the National Electrical Code should always be consulted. The National Electrical Code (NEC) is a registered trademark of the National Fire Protection Association, Quincy, MA. 38 Logic Module with Revised Specifications subject to change without notice

39 14 WIRING DIAGRAMS Maximum Peak Lumens DALI Type 8 Accessory Card Wiring Diagram Notes: 1. 24V power (red/black) is Class-2 rated. 2. One DALI address per linear array / ALM kit. TUNABLE COLOR ROUND LED ARRAY FIXTURE RIBBON CONNECTOR CABLE MAKE SURE TO ALIGN INDEX TAB TO INDEX SLOT. ALM WITH DALI TYPE 8 ACCESSORY BOARD DALI Type 8 accessory board connects to an electrically isolated expansion port within the ALM Fixture manufacturer to provide minimum 18 AWG of DALI wire tail to junction box. Consult DALI specifications for field wiring. DALI CONTROLLER D2 D1 BLACK (Common) RED (+) ALM 24V POWER CABLE ( ) CLASS-2 AC TO DC 24V POWER SUPPLY (SUPPLIED BY OEM) JUNCTION BOX WHITE (NEUTRAL) BLACK (HOT) LINE-IN VOLTAGE (REFER TO POWER SUPPLY) The Constant Hot/Live must not be wired to a switching device. This may be put on a relay for maintenance. 39 Logic Module with Revised Specifications subject to change without notice

40 1 eflicker FREE / HYBRID LED DIMMING Maximum Peak Lumens Hybrid Dimming is a technique of controlling the brightness and color of Lumenetix modules / arrays using two common circuit methods mixed together pulse width modulation (PWM) and dynamic current control. Each has its advantages and disadvantages in terms of consistency, control, efficiency and complexity / cost. But when applied in correct proportions, the advantages of each can be made to stand out. For example, PWM has the advantage of simple circuitry and consistent linear control, whereas current control excels in producing flicker-free dimming and higher LED power efficiency. Lumenetix has developed proprietary electronics and LED characterization techniques that use a blend of each technique to produce a luminaire with zero flicker over most of the dimming and color ranges. The control aspects are all handled by the ALM microprocessor and verified by detailed spectrometer testing on each product before shipment. On products featuring Hybrid Dimming, adjustable LED drive current is used from maximum brightness down to approximately 1%. Then the current setting is held constant and PWM is introduced at a rate up to 2 khz, which continues down to very low dim levels (.1% on some models). While this technique is ordinary for single / dual color LED luminaires, Lumenetix is the only company to have perfected the technique on 6 channels of LED color, and has blended the results in a way that produces no eflicker and provides up to 1% more lumens per watt (at select CCT / Dim settings). 4 Logic Module with Revised Specifications subject to change without notice

41 16 PRE-INSTALLATION NOTES Maximum Peak Lumens DYNAMIC DIMMING ROUND LED ARRAYS Exercise caution when connecting the ribbon cables to the LED arrays. Do not press the domed lens against a hard surface (like a table or workbench) as they can be damaged. Do not break off the indexing tabs. RIBBON CABLE CONNECTORS The ribbon cable connector slot is located on one side of the round LED array. araya LOGIC MODULE Mount the araya Logic Module to the fixture with 6 mm - 8 mm (M2. - M4) screws in desired location. Test-fit all components prior to installation. Mark edges for correct alignment. 41 Logic Module with Revised Specifications subject to change without notice

42 Lumenetix Inc Scotts Valley Drive Scotts Valley, CA