LAB20: EIGRP IPv6. EIGRP: Summarization. Disclaimer
|
|
|
- Robert Carpenter
- 5 years ago
- Views:
Transcription
1 Page1 LAB20: EIGRP IPv6 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material is as complete and accurate as possible, the enclosed material is presented on an as is basis. Neither the authors nor Forum assume any liability or responsibility to any person or entity with respect to loss or damages incurred from the information contained in this guide. This Lab Guide was developed by RSTForum. Any similarities between material presented in this configuration guide and any other material is completely coincidental. EIGRP: Summarization
2 Page2 LAB 20: Diagram Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M.
3 Page3 LAB 20: IPv6 EIGRP Summarization Task 1: Configure IPv6 EIGRP Summarization Step 1 In the configuration mode of router configure 4 loopbacks with IPv6 network address in sequence R1: interface loopback 1 ipv6 address 11:0:0::1/64 interface loopback 2 ipv6 address 11:0:1::1/64 interface loopback 3 ipv6 address 11:0:2::1/64 interface loopback 4 ipv6 address 11:0:3::1/64 Step 2 Disable auto-summarization in IPv6 EIGRP Process & verify IPv6 routes on neighbor routing table R1: ipv6 router eigrp 100 no auto-summary R2#show ipv6 route IPv6 Routing Table - default - 23 entries Codes: C - Connected, L - Local, S - Static, U - Per-user Static route B - BGP, HA - Home Agent, MR - Mobile Router, R - RIP IS - ISIS summary, D - EIGRP, EX - EIGRP external, NM - NEMO ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2, l - LISP D 11:0:0::/64 [90/ ] D 11:0:1::/64 [90/ ] D 11:0:2::/64 [90/ ] D 11:0:3::/64 [90/ ] C 12::/64 [0/0] via Serial2/0, directly connected
4 L 12::A8BB:CCFF:FE00:200/128 [0/0] via Serial2/0, receive C 22:0:0::/64 [0/0] L 22:0:0::2/128 [0/0] C 22:0:1::/64 [0/0] L 22:0:1::2/128 [0/0] C 22:0:2::/64 [0/0] via Loopback2, directly connected L 22:0:2::2/128 [0/0] via Loopback2, receive C 22:0:3::/64 [0/0] via Loopback3, directly connected L 22:0:3::2/128 [0/0] via Loopback3, receive C 23::/64 [0/0] via Ethernet0/0, directly connected L 23::A8BB:CCFF:FE00:200/128 [0/0] via Ethernet0/0, receive D 33:0:0::/64 [90/409600] D 33:0:1::/64 [90/409600] D 33:0:2::/64 [90/409600] D 33:0:3::/64 [90/409600] D 34::/64 [90/ ] D 44:0:0::/64 [90/ ] D 44:0:1::/64 [90/ ] D 44:0:2::/64 [90/ ] D 44:0:3::/64 [90/ ] L FF00::/8 [0/0] via Null0, receive Page4
5 Page5 Step 3 Summarize IPv6 EIGRP routes on outgoing interface R1: interface serial 2/0 ipv6 summary-address 11::/16 (Summarization is configurable on a per-interface basis in any router within network. Router R1 sends summary of 11 network on interface s2/0.) Task 2: Verification: Step 1 Verify receipt of summary route in neighbors IPv6 routing table by following command: R2#show ipv6 route IPv6 Routing Table - default - 20 entries O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2, l - LISP D 11::/16 [90/ ] C 12::/64 [0/0] via Serial2/0, directly connected L 12::A8BB:CCFF:FE00:200/128 [0/0] via Serial2/0, receive C 22:0:1::/64 [0/0] L 22:0:1::2/128 [0/0] C 22:0:2::/64 [0/0] via Loopback2, directly connected L 22:0:2::2/128 [0/0] via Loopback2, receive C 22:0:3::/64 [0/0] L 22:0:3::2/128 [0/0] via Loopback3, receive C 22:0:4::/64 [0/0] via Loopback4, directly connected L 22:0:4::2/128 [0/0] via Loopback4, receive C 23::/64 [0/0] via Ethernet0/0, directly connected L 23::A8BB:CCFF:FE00:200/128 [0/0] via Ethernet0/0, receive D 33:0:1::/64 [90/409600] D 33:0:2::/64 [90/409600]
6 Page6 D 33:0:3::/64 [90/409600] D 33:0:4::/64 [90/409600] D 34::/64 [90/ ] D 44::/16 [90/ ] L FF00::/8 [0/0] via Null0, receive (An IPv6 Summarized route is received from neighbor router.) Step 2 Verify creation of null interface in IPv6 routing table R1#show ipv6 route IPv6 Routing Table - default - 23 entries Codes: C - Connected, L - Local, S - Static, U - Per-user Static route B - BGP, HA - Home Agent, MR - Mobile Router, R - RIP H - NHRP, I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea IS - ISIS summary, D - EIGRP, EX - EIGRP external, NM - NEMO ND - ND Default, NDp - ND Prefix, DCE - Destination, NDr - Redirect O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2, l LISP D 11::/16 [5/128256] via Null0, directly connected C 11:0:1::/64 [0/0] L 11:0:1::1/128 [0/0] C 11:0:2::/64 [0/0] via Loopback2, directly connected L 11:0:2::1/128 [0/0] via Loopback2, receive C 11:0:3::/64 [0/0] via Loopback3, directly connected L 11:0:3::1/128 [0/0] via Loopback3, receive C 11:0:4::/64 [0/0] via Loopback4, directly connected L 11:0:4::1/128 [0/0] via Loopback4, receive C 12::/64 [0/0] via Serial2/0, directly connected
7 Page7 L 12::A8BB:CCFF:FE00:100/128 [0/0] via Serial2/0, receive D 22:0:1::/64 [90/ ] D 22:0:2::/64 [90/ ] D 22:0:3::/64 [90/ ] D 22:0:4::/64 [90/ ] D 23::/64 [90/ ] D 33:0:1::/64 [90/ ] D 33:0:2::/64 [90/ ] D 33:0:3::/64 [90/ ] D 33:0:4::/64 [90/ ] D 34::/64 [90/ ] D 44::/16 [90/ ] L FF00::/8 [0/0] via Null0, receive (When summarization is configured on a router, same router immediately created a routing point to Null 0 for loop prevention.)
LAB12: OSPF IPv6. OSPF: Redistribution. Disclaimer
Page1 LAB12: OSPF IPv6 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB24: EIGRP IPv6. EIGRP: Load Balancing. Disclaimer
Page1 LAB24: EIGRP IPv6 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
Page1. Cisco IOS Software, Linux Software (I86BI_LINUX-ADVENTERPRISEK9-M), Version 15.2(4)M1, DEVELOPMENT TEST SOFTWARE
BGP Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to ensure that all material is as complete
LAB8: Named EIGRP IPv4
Page1 AB8: Named EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB11: EIGRP IPv4. EIGRP: Stub. Disclaimer
Page1 AB11: EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB5: OSPF IPv4. OSPF: Stub. Disclaimer
Page1 LAB5: SPF IPv4 Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB1: BGP IPv4. BGP: Initial Config. Disclaimer
Page1 LAB1: BGP IPv4 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
Configuring IPv6 VPN Provider Edge over MPLS (6VPE)
Configuring IPv6 VPN Provider Edge over MPLS (6VPE) Finding Feature Information, page 1 Configuring 6VPE, page 1 Finding Feature Information Your software release may not support all the features documented
LAB15: EIGRP IPv4. LAB 15: Diagram. Disclaimer
AB15: EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material is as
LAB16: BGP IPv6. BGP: Route Reflector. Disclaimer
Page1 LAB16: BGP IPv6 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB16: Named EIGRP IPv4
AB16: Named EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
Configuring FlexVPN Spoke to Spoke
Last Published Date: March 28, 2014 The FlexVPN Spoke to Spoke feature enables a FlexVPN client to establish a direct crypto tunnel with another FlexVPN client leveraging virtual tunnel interfaces (VTI),
LAB14: Named EIGRP IPv4
Page1 LAB14: Named EIGRP IPv4 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all
Chapter 8 Lab 8-3, Configuring 6to4 Tunnels
Chapter 8 Lab 8-3, Configuring 6to4 Tunnels Topology Objectives Configure EIGRP for IPv4. Create a 6to4 tunnel. Configure static IPv6 routes. Background In this lab, you configure EIGRP for full connectivity
LAB1: EIGRP IPv4. EIGRP: Initial Config. Disclaimer
Page1 AB1: EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB2: Named EIGRP IPv4
Page1 AB2: Named EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB8: OSPF IPv4. OSPF: Virtual Link. Disclaimer
Page1 AB8: OSPF IPv4 Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
Implement Static Routes for IPv6 Configuration Example
Implement Static Routes for IPv6 Configuration Example Document ID: 113361 Contents Introduction Prerequisites Components Used Conventions Configure Network Diagram Configurations Verify Related Information
Lab - Configuring Multi-area OSPFv3 Topology
Topology 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Device Interface IPv6 Address R1 R2 R3 S0/0/0 (DCE) Lo0 Lo1 Lo2 Lo3 S0/0/0 S0/0/1
Route Filtering. Types of prefixes in IP core network: Internal Prefixes External prefixes. Downstream customers Internet prefixes
Types of prefixes in IP core network: Internal Prefixes External prefixes Downstream customers Internet prefixes Internal prefixes originated in IP core network Loopback Transport Connect inter-regional
Chapter 3 Lab 3-2, Multi-Area OSPFv2 and OSPFv3 with Stub Area
Chapter 3 Topology Objectives Configure multi-area OSPFv2 for IPv4. Configure multi-area OSPFv3 for IPv6 Verify multi-area behavior. Configure stub and totally stubby areas for OSPFv2. Configure stub and
Route Filtering. Types of prefixes in IP core network: Internal Prefixes External prefixes. Downstream customers Internet prefixes
1 Types of prefixes in IP core network: Internal Prefixes External prefixes Downstream customers Internet prefixes 2 Internal prefixes originated in IP core network Loopback Transport Connect inter-regional
Basic Router Configuration
This section includes information about some basic router configuration, and contains the following sections: Default Configuration, on page 1 Configuring Global Parameters, on page 2 Configuring Gigabit
Configuring IPv6 Provider Edge over MPLS (6PE)
Finding Feature Information, page 1 Configuring 6PE, page 1 Finding Feature Information Your software release may not support all the features documented in this module. For the latest caveats and feature
Topology & EIGRP Invocation. Router# show ipv6 protocols. Router# show ipv6 eigrp neighbors [ detail fa0/0 ]
![Topology & EIGRP Invocation. Router# show ipv6 protocols. Router# show ipv6 eigrp neighbors [ detail fa0/0 ]](/thumbs/78/78661316.jpg "Topology & EIGRP Invocation. Router# show ipv6 protocols. Router# show ipv6 eigrp neighbors [ detail fa0/0 ]")
Topology & EIGRP Invocation Router-ID is in the EIGRP block Interfaces included at each interface Passive interfaces designated in the EIGRP block The EIGRP block may require a no shutdown R5 ipv6 unicast-routing
Lab Configuring IPv6 Static and Default Routes (Solution)
(Solution) Topology Addressing Table Device Interface IPv6 Address / Prefix Length Default Gateway R1 G0/1 2001:DB8:ACAD:A::/64 eui-64 N/A S0/0/1 FC00::1/64 N/A R3 G0/1 2001:DB8:ACAD:B::/64 eui-64 N/A
Chapter 1 Lab 1-1, Basic RIPng and Default Gateway Configuration
Chapter 1 Lab 1-1, Basic RIPng and Default Gateway Configuration Topology Objectives Configure IPv6 addressing. Configure and verify RIPng on R1 and R2. Configure IPv6 static routes between R2 and R3.
Adjust Administrative Distance for Route Selection in Cisco IOS Routers Configuration Example
Adjust Administrative Distance for Route Selection in Cisco IOS Routers Configuration Example Document ID: 113153 Contents Introduction Prerequisites Requirements Components Used Conventions Configure
Layer3 VPN with OSPF Protocol between CE-PE
MPLS Layer3 VPN with OSPF Protocol between CE-PE Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made
DMVPN Topology. Page1
DMVPN DMVPN Topology Page1 LAB 2: Configure EIGRP over DMVPN: Task 1: Configure EIGRP over DMVPN Process Step 1 In the configuration mode of router configure EIGRP over DMVPN by following command: R1:
IPv6 BGP AS Path. R1 Router Config:! ipv6 unicast-routing ipv6 cef. R4 Router Config:! ipv6 unicast-routing ipv6 cef Page1
IPv6 IPv6 BGP AS Path Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to ensure that all material
IPv6 Routing Protocols Update
IPv6 Routing Protocols Update Wim Verrydt Solutions Architect BRKRST-2022 Abstract and Pre-requisite The proposed session provides a comprehensive overview of the main IPv6 routing protocols: IS-IS, OSPFv3,
Central America Workshop - Guatemala City Guatemala 30 January - 1 February 07
Central America Workshop - Guatemala City Guatemala 30 January - 1 February 07 IPv6 Router s Configuration #2 Pedro Lorga (lorga@fccn.pt) Simon Muyal (muyal@renater.pt) Piers O'Hanlon (p.ohanlon@cs.ucl.ac.uk)
Network Layer Week 5. Module : Computer Networks Lecturer: Lucy White Office : 324
Network Layer Week 5 Module : Computer Networks Lecturer: Lucy White lbwhite@wit.ie Office : 324 1 Network Layer Network Layer Protocols Common Network Layer Protocols Internet Protocol version 4 (IPv4)
IPv6 Routing Protocols
IPv6 Routing Protocols ITU/APNIC/PacNOG21 IPv6 Workshop 4 th 8 th December 2017 Nuku alofa These materials are licensed under the Creative Commons Attribution-NonCommercial 4.0 International license (http://creativecommons.org/licenses/by-nc/4.0/)
Layer3 VPN with RIP protocol between CE-PE
MPLS Layer3 VPN with IP protocol between E-PE Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to
OSPFv3 Route Filtering Using Distribute-List
The OSPFv3 route filtering using distribute-list feature allows users to filter the incoming routes that are programmed in routing table, and the outgoing routes that are advertised. Finding Feature Information,
Implementing Static Routes for IPv6
Implementing Static Routes for IPv6 Last Updated: July 31, 2012 This module describes how to configure static routes for IPv6. Routing defines the paths over which packets travel in the network. Manually
AS 100 AS 300. Lab -1 Private Communities - II .1 S1/2. Task 1. On R1: / / /24. Configure the above topology.
Lab -1 Private Communities - II AS 100.1 R1 S1/2 12.1.1.0/24 S1/1.2 R2 S1/3 S1/3 13.1.1.0/24 23.1.1.0/24 S1/1.3 R3 S1/2 Lo0 6.6.6.0/24 Lo1 7.7.7.0/24 AS 300 Task 1 Configure the above topology. On R1:
South America Workshop WALC 2006 (Quito, Ecuador July 06) Router Configuration #2 (continued)
South America Workshop WALC 2006 (Quito, Ecuador 26-28 July 06) Router Configuration #2 (continued) Miguel Baptista (miguel.baptista@fccn.pt) Pedro Lorga (lorga@fccn.pt) Simon Muyal (muyal@renater.pt)
Chapter 4 Lab 4-2, Controlling Routing Updates. Topology. Objectives. CCNPv7 ROUTE
Chapter 4 Lab 4-2, Controlling Routing Updates Topology Objectives Filter routes using a distribute list and ACL. Filter routes using a distribute list and prefix list. Filter redistributed routes using
IPv6 Module 2 OSPF Areas
ISP Workshop Lab IPv6 Module 2 OSPF Areas Objective: To migrate from one flat OSPF topology to OSPF areas, plus introduce neighbour authentication and area summarisation in the lab network. Prerequisite:
Disclaimer. IOS used: c7200-p-mz s.bin. Page1
MPLS Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to ensure that all material is as complete
RR> RR> RR>en RR# RR# RR# RR# *Oct 2 04:57:03.684: %AMDP2_FE-6-EXCESSCOLL: Ethernet0/2 TDR=0, TRC=0 RR#
RR> RR> RR>en *Oct 2 04:57:03.684: %AMDP2_FE-6-EXCESSCOLL: Ethernet0/2 TDR=0, TRC=0 term len 0 show run Building configuration... Current configuration : 2568 bytes version 15.4 service timestamps debug
South America Workshop WALC 2006 (Quito, Ecuador July 06)
South America Workshop WALC 2006 (Quito, Ecuador 26-28 July 06) RIP for IPv6 Configuration Pedro Lorga (lorga@fccn.pt) Miguel Baptista (miguel.baptista@fccn.pt) Simon Muyal (muyal@renater.pt) Laboratory
FlexVPN HA Dual Hub Configuration Example
FlexVPN HA Dual Hub Configuration Example Document ID: 118888 Contributed by Piotr Kupisiewicz, Wen Zhang, and Frederic Detienne, Cisco TAC Engineers. Apr 08, 2015 Contents Introduction Prerequisites Requirements
Sample Configuration for OSPFv3
Sample Configuration for OSPFv3 Document ID: 112100 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configuration Verify Troubleshoot Related Information
Laura McDonnell 11 th June 2008
Laura McDonnell 11 th June 2008 Background Why? How? Problems encountered? What next? 7 PoP sites 29 Connected Sites Including Kent Schools Network 5 HE s KM Core BT wavestream circuits (DWDM) 2.5Gbps
INTERNET TEACHING LAB: Interior Gateway Protocol (IGP) LAB
INTERNET TEACHING LAB: Interior Gateway Protocol (IGP) LAB Overview In this lab, we will explore some common interior gateway protocols - RIP version 1 (Routing Information Protocol) - OSPF (Open Shortest
Internet Protocol Version 6: advanced features. The innovative aspects of IPv6
Internet Protocol Version 6: advanced features The innovative aspects of IPv6 1 Autoconfiguration Addresses are composed by Information held by routers (network address) Information locally available (interface
Chapter 6 Lab 6-4, BGP Route Reflectors and Route Filters
Chapter 6 Lab 6-4, BGP Route Reflectors and Route Filters Topology Objectives Background Configure IBGP routers to use a route reflector and a simple route filter. The International Travel Agency maintains
Easy Virtual Network Configuration Example
Easy Virtual Network Configuration Example Document ID: 117974 Contributed by Fabrice Ducomble, Cisco TAC Engineer. Aug 04, 2014 Contents Introduction Prerequisites Requirements Components Used Background
2001, Cisco Systems, Inc. All rights reserved.
2001, Cisco Systems, Inc. All rights reserved. 1 OSPFv3 2 OSPFv2 Latest revision is RFC 2328 April 1998 OSPF uses a 2 level hierarchical model SPF calculation is performed independently for each area Typically
Implementing RIP for IPv6
Implementing RIP for IPv6 This module describes how to configure Routing Information Protocol for IPv6. RIP is a distance-vector routing protocol that uses hop count as a routing metric. RIP is an Interior
Lab- Troubleshooting Basic EIGRP for 1Pv4
Lab- Troubleshooting Basic EIGRP for 1Pv4 Topology G0/0 G0/0 PC-A PC-C 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 27 Addressing Table efault Gateway
Route Redistribution 2005 Cisco Systems, Inc. All rights reserved. 1of 38
1of 38 Basic Route Redistribution Presented by: Allan Johnson Cisco Academy Conference 2005 2of 38 Outline of Discussion Route Redistribution Overview Example 1: IGRP and EIGRP Automatic Redistribution
NIS Workshop - Ashgabad April Routing hands-on: Local Lab
NIS Workshop - Ashgabad 25-27 April 2007 Routing hands-on: Local Lab Piers O'Hanlon Peter Kirstein Janos Mohacsi Nikolay Pakulin
CCNA Exploration: Routing Protocols and Concepts Chapter 11 Case Study
bjectives: Consolidate SPF knowledge. Describe the operation of SPF multi-area. Introduce the concept of route summarization with SPF. Introduce the concept of SPF optimization. Intro: Trevni Inc. needed
CCNA Exploration: Routing Protocols and Concepts Chapter 8 Case Study
Objectives: Consolidate routing table reading skills. Introduce the idea of more than 1 routing protocol running into the same router. Explain the use of routes to Null0 interface. Intro: Connex Inc. is
IPv6 Commands: d to im
IPv6 Commands: d to im data-glean, page 3 default (IPv6 OSPF), page 5 default (OSPFv3), page 7 default-information originate (IPv6 IS-IS), page 10 default-information originate (IPv6 OSPF), page 12 default-information
Chapter 7 Lab 7-2, Using the AS_PATH Attribute
Chapter 7 Topology Objectives Use BGP commands to prevent private AS numbers from being advertised to the outside world. Use the AS_PATH attribute to filter BGP routes based on their source AS numbers.
GRE Tunnel with VRF Configuration Example
GRE Tunnel with VRF Configuration Example Document ID: 46252 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot Caveats
Lab Configuring IPv4 Static and Default Routes (Solution)
(Solution) Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.0.1 255.255.255.0 N/A S0/0/1 10.1.1.1 255.255.255.252 N/A R3 G0/1 192.168.1.1 255.255.255.0
Chapter 4 Lab 4-1, Redistribution Between RIP and OSPF
hapter 4 Lab 4-1, Redistribution Between RIP and OSPF Topology Objectives Review configuration and verification of RIP and OSPF. onfigure passive interfaces in both RIP and OSPF. Filter routing updates
Routing Information Protocol Version 2.0
Routing Information Protocol Version 2.0 RIPv2 Objective: onfigure RIPv2 between R1 and R2 to obtain connectivity between Networks Directions onfigure R1's interface F0/0 with the IP address 10.1.0.1/16
IPv6 Commands: d to im
data-glean, on page 3 default (IPv6 OSPF), on page 5 default (OSPFv3), on page 7 default-information originate (IPv6 IS-IS), on page 9 default-information originate (IPv6 OSPF), on page 11 default-information
Chapter 4 Lab 4-2, Redistribution Between EIGRP and OSPF
Chapter 4 Lab 4-2, Redistribution Between EIGRP and OSPF Topology Objectives Review EIGRP and OSPF configuration. Redistribute into EIGRP. Redistribute into OSPF. Summarize routes in EIGRP. Filter routes
Contents. Introduction. Prerequisites. Requirements
Contents Introduction Prerequisites Requirements Components Used Configure Network Diagram Configurations Verify Inheritence with EIGRP Named mode Route Replication with EIGRP name mode Routing Context
Shortcut Switching Enhancements for NHRP in DMVPN Networks
Shortcut Switching Enhancements for NHRP in DMVPN Networks Routers in a Dynamic Multipoint VPN (DMVPN) Phase 3 network use Next Hop Resolution Protocol (NHRP) Shortcut Switching to discover shorter paths
ASA Has High CPU Usage Due to a Traffic Loop When VPN Clients Disconnect
ASA Has High CPU Usage Due to a Traffic Loop When VPN Clients Disconnect Contents Introduction Prerequisites Requirements Components Used Background Information Problem: Packets Destined for a Disconnected
Implementing RIP for IPv6
Implementing RIP for IPv6 Last Updated: July 31, 2012 This module describes how to configure Routing Information Protocol for IPv6. RIP is a distance-vector routing protocol that uses hop count as a routing
RIPv2. Routing Protocols and Concepts Chapter 7. ITE PC v4.0 Chapter Cisco Systems, Inc. All rights reserved. Cisco Public
RIPv2 Routing Protocols and Concepts Chapter 7 1 Objectives Encounter and describe the limitations of RIPv1 s limitations. Apply the basic Routing Information Protocol Version 2 (RIPv2) configuration commands
Lab Configuring Static NAT
Lab 10.5.1 Configuring Static NAT Objective Configure Network Address Translation (NAT) static translation to provide reliable outside access to three shared company servers. Scenario Step 1 The International
RIP. Table of Contents. General Information. Summary. Specifications
RIP Document revision 1 (Wed Mar 24 12:32:12 GMT 2004) This document applies to V2.8 Table of Contents Table of Contents General Information Summary Specifications Related Documents Additional Documents
MPLS VPN Half-Duplex VRF
The feature provides scalable hub-and-spoke connectivity for subscribers of an Multiprotocol Label Switching (MPLS) Virtual Private Network (VPN) service. This feature addresses the limitations of hub-and-spoke
CIS 83 LAB 3 - EIGRP Rich Simms September 23, Objective. Scenario. Topology
CIS 83 LAB 3 - EIGRP Rich Simms September 23, 2006 Objective The objective of this lab is to become familiar setting up and configuring EIGRP on three routers. EIGRP is a Cisco proprietary distance-vector
Building the Routing Table. Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles
Building the Routing Table Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles Introducing the Routing Table R1# show ip route Codes: C - connected,
LAB 9: Configure BGP Confederation
BGP BGP Topology Page1 LAB 9: Configure BGP Confederation Task 1: Configure IPv4 BGP Process for Autonomous Step 1. In the configuration mode of router configure IPv4 BGP Process by following command:
TELECOMMUNICATION MANAGEMENT AND NETWORKS
QUAID-E-AWAM UNIVERSITY OF ENGINEERING SCIENCE AND TECHNOLOGY, NAWABSHAH TELECOMMUNICATION MANAGEMENT AND NETWORKS LAB # 3 CONFIGURING INTERFACES OF ROUTER AND SWITCH Topology Diagram Addressing Table
KIM DONNERBORG / RTS. Cisco Lab Øvelse Af Kim Donnerborg / RTS. Side 0 af 8
KIM DONNERBORG / RTS Side 0 af 8 INDHOLDSFORTEGNELSE Lab: Basic Router Configuration... 2 Topology Diagram... 2 Addressing Table... 2 Learning Objectives... 2 Scenario... 2 Task 1: Cable the Network....
CCNA Exploration: Routing Protocols and Concepts Chapter 10 Case Study
Objectives: Use OSPF single area to illustrate basic Link State components and operation. Migrate from EIGRP to OSPF single area. Intro: Trevni Inc. decided to upgrade their routing protocol from EIGRP
LAB 5: DMVPN BGP. LAB 5: Diagram. Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M.
LAB 5: DMVPN BGP LAB 5: Diagram Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M. LAB 5: Configure BGP over DMVPN Configuration Step 1: Enable loopback and physical interfaces
Configuring Scalable Hub-and-Spoke MPLS VPNs
Configuring Scalable Hub-and-Spoke MPLS VPNs Last Updated: December 15, 2011 This module explains how to ensure that virtual private network (VPN) clients that connect to the same provider edge (PE) router
Any individual involved in implementation and verification of routing protocols in the enterprise networks
IMPLEMENTING CISCO IP ROUTING Information Length: 5 Days Courseware : Course code: Delivery Type Included CIS_ROUTE Classroom Description Implementing Cisco IP Routing (ROUTE) v1.0 is a five-day course
COURSE OUTLINE: Course: CCNP Route Duration: 40 Hours
COURSE OUTLINE: Course: CCNP Route 300-101 Duration: 40 Hours CCNP Route Training Day 1: Connecting Remote Locations Principles of Static Routing Configuring an IPv4 Static Route Configuring a Static Default
Routing Protocol Type Primarily IGP or EGP RIP Distance-Vector IGP EIGRP OSPF IS-IS BGP
Appendix D Memory Tables Chapter 1 Table 1-2 Routing Protocol Characteristics Routing Protocol Type Primarily IGP or EGP RIP Distance-Vector IGP EIGRP OSPF IS-IS BGP Chapter 3 Table 3-2 Hexadecimal/Binary
IPv6 Tunnel through an IPv4 Network
IPv6 Tunnel through an IPv4 Network Document ID: 25156 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations (Manual IPv6 Mode) Configurations
SDN Workshop. Contact: WSDN01_v0.1
SDN Workshop Contact: training@apnic.net WSDN01_v0.1 Issue Date: [Date] Revision: [xx] BGP-LS - Lab SDN Workshop WSDN01_v0.1 Issue Date: [Date] Revision: [xx] BGP-LS Configuration 3 Configuration Example
CCNP ROUTE Workbook - EIGRP
CCNP ROUTE Workbook - EIGRP EIGRP Initial Configuration Load the task1-1 initial configurations before starting. Task Configure EIGRP on Routers-1, 2, and 4 using the following guidelines: Classic-mode
Initial Configurations for OSPF over a Point to Point Link
Initial onfigurations for OSPF over a Point to Point Link Document ID: 13687 ontents Introduction Prerequisites Requirements omponents Used onventions OSPF over a Point to Point Link with IP Addresses
Lab Configuring Per-Interface Inter-VLAN Routing (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/0 192.168.20.1 255.255.255.0 N/A G0/1 192.168.10.1 255.255.255.0 N/A S1 VLAN 10 192.168.10.11
Complex MPLS VPN with OSPF on CE-PE Routers
MPLS Complex MPLS VPN with OSPF on CE-PE Routers Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made
LAB 3: DMVPN EIGRP. EIGRP over DMVPN. Disclaimer. Pag e
LAB 3: DMVPN EIGRP Disclaimr This Configuration Guid is dsignd to assist mmbrs to nhanc thir skills in rspctiv tchnology ara. Whil vry ffort has bn mad to nsur that all matrial is as complt and accurat
Chapter 4 Lab 4-1, Redistribution Between EIGRP and OSPF. Topology. Objectives. CCNPv7 ROUTE
hapter 4 Topology Objectives Review EIGRP and OSPF configuration. Summarize routes in EIGRP. Summarize in OSPF at an ABR. Redistribute into EIGRP. Redistribute into OSPF. Summarize in OSPF at an ASBR.
Lab Configuring Per-Interface Inter-VLAN Routing (Instructor Version)
(Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
OSPF Commands. Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols IP2R-61
OSPF Commands Use the commands in this chapter to configure and monitor the Open Shortest Path First (OSPF) routing protocol. For OSPF configuration information and examples, refer to the Configuring OSPF
STUDENT LAB GUIDE CCNA ( )
STUDENT LAB GUIDE CCNA (640-802) Developed By, Router Infotech Career Academy LAB: 09 Static Route Configuration Objective: To configure & implement Static Route successfully on said devices and test its
CertifyMe. CertifyMe
CertifyMe Number: 642-661 Passing Score: 800 Time Limit: 120 min File Version: 7.6 http://www.gratisexam.com/ CertifyMe-642-661 Exam A QUESTION 1 Exhibit: Certkiller router#show ip route Codes: C - connected,
CCIE Service Provider Sample Lab. Part 2 of 7
CCIE Service Provider Sample Lab Part 2 of 7 SP Sample Lab Main Topology R13 S2/1.135.13/24 Backbone Carrier SP AS 1002 S2/1 PPP E0/1.69.6/24 R6 Customer Carrier SP ABC Site 5 AS 612 E1/0 ISIS.126.6/24
LAB 4: DMVPN OSPF. OSPF over DMVPN. Disclaimer. Pag e
LAB 4: DMVPN OSPF Disclaimr This Configuration Guid is dsignd to assist mmbrs to nhanc thir skills in rspctiv tchnology ara. Whil vry ffort has bn mad to nsur that all matrial is as complt and accurat