Interoperability/ Conformance Test dpmr Mode 2 Repeater

Transcription

1 Interoperability/ Conforance Test dpmr Mode 2 Repeater IOP test Mode 2 Repeater Copyright 2013 dpmr Association All Rights Reserved Version 1.0

2 0 Revision History Version Date Change By 0v1 16 Oct 2012 Updated for repeater IOP test TH 0v2 12 Dec 2012 Update several typos TH 0v3 22 Feb 2013 Add ulti band test ites (Clause 1.3). Update initial conditions (Clause 2.1). TH 0v4 22 Feb 2013 Reduce nuber of REF units to be 2. Update test procedures (Clause 2.2.1, 2.2.2, TH 2.2.3, 2.2.4, 3.1.1, 3.1.2, 3.2.1, 3.2.2) 1v0 28 Mar 2013 Approved by TWG TH/DL 0 Revision History Scope Abbreviations: Reference Unit Multi-band equipent Test Profile Mode 2 Voice Initial conditions: Repeat Tests: ID call: Group Call: Status Messages: Slow User data Invalid Vocoder selection Test Profile Mode 2 Data Type 1 Repeat Tests: ID call: Group Call: Type 2 Repeat Tests ID call: Group Call: Packet Data RF testing Appendix 1 Test Data Data content Appendix 2 Canned Status Message Text

3 1 Scope The purpose of this docuent is to provide the suary of Interoperability Tests for dpmr Mode 2 repeater. Test ites have been extracted fro the functions defined in ETSI TS Profiles are supported for each ode: Voice operation Data operation Voice + Data operation Packet Data In each profile a nuber of optional features are supported, which, if ipleented, ust confor to this docuent. REF EUT TPI o c 1.1 Abbreviations: Reference Unit Equipent under test Talking Party Identification optional andatory conditional 1.2 Reference Unit The current reference units for tests (REF 1 and REF 2) are the Ico IC F3162DT or IC F4162DT (portable). For ites/features not supported by this unit, the CML dpmr test syste ay be used. This should be noted in the test report. For these tests all counications between reference terinals should be through the EUT repeater unit. No direct terinal to terinal counication is perissible. 3

4 1.3 Multi-band equipent Where a product is supplied in ultiple RF bands all using the sae protocol and control software, it is only necessary to perfor the full conforance test on one band. The other bands shall be verified by executing the following sub set on each variant: Mode 2: ID call: Group call: RF tests: Equipent shall be tested to the relevant requireents of EN The requireents of dpmr RF Tests.doc ust be satisfied. 4

5 2 Test Profile Mode 2 Voice Reference units should be prograed with both an Individual ID and Talk Group ID 2.1 Initial conditions: EUT should be prograed with appropriate uplink and downlink frequencies to be copatible with the reference units. REF 1: ID TG REF 2 Setting1: ID TG REF 2 Setting2: ID TG REF 2 Setting3: ID TG Display of TPI is optional Slow User Data support is optional 2.2 Repeat Tests: ID call: Turn EUT and all REFs on. On REF 1, select ID On REF2, select Setting1 (ID ) REF 2 should indicate TPI= voice should be heard Confir that the repeat operation is correct. On REF2, select Setting2 (ID ) REF 2 should reain silent Confir that the repeat operation is correct. On REF2, select Setting3 (ID ) REF 2 should reain silent Confir that the repeat operation is correct Group Call: On REF 1, select ID On REF2, select Setting1 REF 2 should indicate TPI= voice should be heard Confir that the repeat operation is correct. On REF2, select Setting2 5

6 REF 2 should indicate TPI= voice should be heard On REF2, select Setting3 REF 2 should indicate TPI= voice should be heard Status Messages: On REF 1, select ID ID Status Call On REF2, select Setting1 (ID ) Select Status sg1 on REF 1 Send status sg fro REF 1 REF 2 should display Status sg1 c indicate TPI= Confir that the repeat operation is correct. On REF2, select Setting2 (ID ) Send status sg fro REF 1 REF 2 should reain silent On REF2, select Setting3 (ID ) Send status sg fro REF 1 REF 2 should reain silent On REF 1, select ID On REF 2, select Setting1 Select Status sg1 on REF 1 Send status sg fro REF 1 REF 2 should display Status sg1 c indicate TPI= On REF 2, select Setting2 Send status sg fro REF 1 REF 2 should display Status sg1 c indicate TPI= On REF 2, select Setting3 Send status sg fro REF 1 REF 2 should display Status sg1 c indicate TPI= Group Status Call Slow User data Note: REF 1 does not support this ode This is a conditional feature Enable Slow Data on REF 1 On REF 1, select ID On REF2, select Setting1 (ID ) ID Call 6

7 REF 2 should indicate TPI= voice should be heard Slow data available c On REF2, select Setting2 (ID ) REF 2 should reain silent On REF2, select Setting3 (ID ) REF 2 should reain silent Enable Slow Data on REF 1 On REF 1, select ID On REF2, select Setting1 REF 2 should indicate TPI= voice should be heard Slow data available c On REF2, select Setting2 REF 2 should indicate TPI= voice should be heard Slow data available c On REF2, select Setting3 REF 2 should indicate TPI= voice should be heard Slow data available c Group Call Invalid Vocoder selection Note: REF 1 does not support this ode On REF 1, select a Vocoder ode that is NOT supported by REF 2 On REF 1, select ID REF 2 should indicate TPI= o reain silent Indicate no voice o Release PTT 7

8 3 Test Profile Mode 2 Data 3.1 Type 1 Repeat Tests: REF 1: ID TG REF 2 Setting 1: ID TG REF 2 Setting 2: ID TG REF 2 Setting 3: ID TG Data Content of call is specified in Appendix 1. Data ay be provided and/or delivered to an externally connected device or generated/displayed on the EUT as appropriate. Data content ay be one or ore of the following, (the forat used for testing should be recorded); Status essage Pre coded essage Free text essage Short file transfer IP data transfer ID call: Turn EUT and all REFs on. Enable Type 1 Data Call on all REFs On REF 1, select ID On REF 2, select Setting 1 (ID ) Send Data Call fro REF 1 REF 2 should indicate TPI= On REF2, select Setting 2 (ID ) Send status sg fro REF 1 REF 2 should reain silent On REF2, select Setting 3 (ID ) Send status sg fro REF 1 REF 2 should reain silent Group Call: On REF 1, select ID On REF 2, select Setting 1 Send Data Call fro REF 1 REF 2 should indicate TPI= On REF 2, select Setting 2 Send Data Call fro REF 1 REF 2 should indicate TPI= On REF 2, select Setting 3 Send Data Call fro REF 1 REF 2 should indicate TPI=

9 3.2 Type 2 Repeat Tests REF 1: ID TG REF 2 Setting 1: ID TG REF 2 Setting 2: ID TG REF 2 Setting 3: ID TG ID call: Turn EUT and all REFs on. Enable Type 1 Data Call on all REFs On REF 1, select ID On REF 2, select Setting 1 (ID ) Send Data Call fro REF 1 REF 2 should indicate TPI= On REF2, select Setting 2 (ID ) Send status sg fro REF 1 REF 2 should reain silent On REF2, select Setting 3 (ID ) Send status sg fro REF 1 REF 2 should reain silent Group Call: On REF 1, select ID On REF 2, select Setting 1 Send Data Call fro REF 1 REF 2 should indicate TPI= On REF 2, select Setting 2 Send Data Call fro REF 1 REF 2 should indicate TPI= On REF 2, select Setting 3 Send Data Call fro REF 1 REF 2 should indicate TPI=

10 4 Packet Data Packet data is also referred to as Type 3 Data in TS Test TBD 10

11 5 RF testing Equipent shall be tested to the relevant requireents of EN In addition, the defined in the dpmr Assoc. docuent dpmr RF Tests.doc shall be satisfied. 11

12 6 Appendix 1 Test Data 6.1 Data content For the data transfer tests, a coon data set should be used to enable autoated testing: Status essage: dpmr MoU test status essage Pre coded essage dpmr MoU pre coded test essage Free text essage dpmr MoU free text essage Short file transfer See attached file short data file IP data transfer TBD For the Slow User Data tests either a valid NMEA 183 data string (ie: GPS data) or the Status essage can be used. 12

13 7 Appendix 2 Canned Status Message Text The following canned status sg text ay be used. If a non English language text is used, the eaning should reain the sae as the English text: 1 to 16 user or anufacturer defined 17 to 29 to be defined 30 Call Hoe 31 Urgent 32 Return to Base 13