Long Range Motion Radar Sensor IRS01

Transcription

1 Long Range Motion Radar Sensor IRS1 Vehicle and person detection Long range of detection In field adjustent of the area detection with reote control Low power consuption Sealed against dust and huidity 7 axiu height CE682, FCC, UR, UL325 Product Description Ordering Key IRS 1 IRS Long range sensor is a digital unidirectional otion sensor for trouble-free opening of all types of industrial autoatic doors. It can be adapted to every application without further accessories and can be controlled by an infrared reote controller. Mounting height up to 7 (23) to detect vehicle or person otion towards or away fro the sensor. Like ost of other icrowave detectors equipped with planar flat antenna, the sensor works on echo doppler signal for detecting oveents. Type Detection ode General Data Sensing field orientation Detection angle Detecting area Detection ode Unidirectional Bidirectional Motion detecting speed Frequency eitted Approvals By housing orientation ± vertical and lateral see the Maxiu Field Extension pictures to detect otions towards or away fro sensor to detect otions towards and away fro sensor.5 - /s ( fps) along sensor axis (K-Band) GHz CE682, FCC, UR and UL325 Electrical Data Radiated power <16dB EIRP Rated supply voltage 12 24VAC ±1% 12 32VDC Main frequency 5 to 6HZ Power consuption <1.2W Output Relay 2 x SPDT Rated Voltage 3VAC/DC Max switching current 1A (resistive load) Max switching power 3W (resistive load) Powered by Class 2 or LVE transforer Hold tie.5 6s (adjustable) Environental Data Teperature range -2 C to +6 C (-4 F to +14 F) Huidity fro % to 9%RH Iunity R&TTE 1999/5/EC EMC 24/18/EEC Max. ounting height 2.5 to 7 ( to ) Degree of protection IP65, NEMA - 4 Mechanical Data Housing Material Diensions WxHxD Weight Cable length Colour Aluiniu with plastic junction box 137 x 188 x 91.5 (5.39 x 7.4 x 3.6inch.) 3g (1.58oz) 5 (16.4) Black Specifications are subject to change without notice ( ) 1

2 Adjustents and Settings Manual adjustent Reote control adjustents Sensitivity R1 and R2 Relay hold tie orientation of sensing field (echanically) ultiple functions (by push buttons on board inside). Sensitivity Hold tie Mounting height Detection ode Iunity Relay configuration 5 levels. It allows increent or decreent of detection field. 5 levels (.5 to 6s). Iunity detection R1 and R2 Relay status Security code Noral ode Iunity Quasi-presence Lateral Traffic suppression Active, Passive, can be set independently by reote controller; Switching in autoatic ode (noral detection) the last status of relays will be considered as steady state condition. 4-digit PIN access code to lock or unlock the keyboard of controller. Unidirectional ode Forward or backward. Switching ON and factory settings 1. Aer the supply voltage has been connected, the RED LED will start flashing quickly for 3 seconds. The unit is set up in factory at the following default values: A) Sensitivity: level 1 (SENS+1) B) Mounting height: 2.5 to 3.5 (F1) C) Relay hold tie:.5 sec (HT+1) D) Operating ode V or P E) Detection Recognition oveents towards the detector (FW) F) Iunity, Quasi-presence, and Lateral Traffic Suppression: OFF G) R1 and R2 Relay Status: OFF in rest condition H) PIN security: - lock keyboard disabled on reote controller 2. Set ounting height (F1 F4) if different fro factory setting. The detector will not function correctly if the wrong ounting height is set 3. Set field size (SEN+1 5) and if necessary using inclination angle, Set the optional volue of Relay Hold tie (HT ) if different fro factory setting HT+1 (.5 ) 5. Set the other paraeters as the specific application requires. Electrical Connection The unit should be powered by Class 2 or LVE transforer. Do not switch on the power until all priary and secondary wiring are copleted. The contacts of relays should be connected to Class 2 circuit. Opening the junction box of the housing an 8 pole snap connector will be accessible. Connect the wires as below indicated. VS1 VS2 1 1 COM1 2 2 COM2 Code VS1 VS2 1 1 COM1 2 2 COM2 Description First supply terinal Second supply terinal Relay n 1 - Norally close contact Relay n 1 - Norally open contact Relay n 1 - Coon Relay n 2 - Norally close contact Relay n 2 - Norally open contact Relay n 2 - Coon 2 Specifications are subject to change without notice ( )

3 Inside View Mounting Instructions Push Button I (+) Planar Antenna Red LED IR Receiver Wall ounting Green LED Push Button DEC (-) To install the radar is necessary only a screwdriver and drill. Sensing Field adjustent Mechanical sensor orientation Planar antenna vertical angle fro to Sensing field adjustent according to Sensitivity setting and ounting Height The sensing field area size (lobo) depends on the sensitivity paraeter setting and the radar ounting height Adjust the vertical position to obtain the vertical sensing field close or far fro the door. Maxiu field extension (with level 5 as sensitivity) Mounting height: 4.5 with 3 different inclination angles Mounting height: 7 with 3 different inclination angles Specifications are subject to change without notice ( ) 3 COM COM

4 Installation Tips The sensor shall be firly fixed to avoid any 3.5 false 3.5 activation.5 by shocks or vibrations. It should not be ounted to high vibration surfaces 3.5 such as.5a 3.5 door canopy that houses the operating echanis Signalling by LED The RED and GREEN LED flash in the following conditions: When power is turned ON, the RED LED flashes for 3 seconds During a object detection the GREEN or RED LED lights ON (depending by operating ode setting). Relay vs Function Relay # IR Reote controller button Do not install the radar close to flourescent laps. 1 R1 Vehicles RED R2 Persons GREEN Sensor should not be placed near etal halide lights or placed behind any kind of protection layer or plate. During prograing procedure by reote controller the RED LED flashes any ties as the function being odified (see following table). A blind tie of 5 seconds will be inserted during the signalling. During anual prograing procedure the RED and GREEN LED flash a nuber of tie corresponding to the step of the procedure (see description of the procedure). Function LED Direction Connection pin Relay 8. configuration at DETECTION 8. R1 / Red LED R2 / Green LED LED OFF LED ON Forward (also Backward & Bidirection in PR operating ode) Backward (also Forward & Bidirection in VR operating ode) The housing of the sensor is concealed within a NEMA-4 type-rated enclosures and is extreely reliable in harsh environents. COM - pin5 - pin4 - pin3 COM - pin8 - pin7 - pin6 4 Specifications are subject to change without notice ( )

5 Diensions (inches) Accessory Ordering Key Type IR reote controller IRS RC Mounting Height adjusent Operating odes IRS--RC CONTROL F R1 R2 AUTO R1 anual control R2 anual control Autoatic control F5: Lateral traffic suppression OFF/ON 72 PIN change/reset PR V / P VR Iunity OFF/ON VorP 72 Lock/Unlock keyboard of Reote control L / U PIN FW BKW FS IMM SEN HT Hold tie adjustent Forward / Backward / Bi-directional detection Sensitivity adjustent Display Values Quasi-presence OFF/ON Note: For optiu results point the reote control at the sensor before pressing its buttons Note: before using the reote controller open the battery copartent at the back of the reote control; insert two AAA batteries supplied with the reote control; close the batteries copartent. Approvals Trade Nae: Carlo Gavazzi Logistics S.p.A. via Milano 13, I-22 Lainate (MI) Model No: FCC ID: IC: IRS1 U7PIRS1 7118A-IRS1 This device coplies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) this device ay not cause harful interference, and (2) this device ust accept any interference received, including interference that ay cause undesired operation. Specifications are subject to change without notice ( ) 5