SUPER HI-RES. FAST DOME CAMERA

Transcription

1 SUPER HI-RES. FAST DOME CAMERA SP0/0// Series SUPER HI-RES. FAST DOME IP CAMERA IPS0/0// Series INSTRUCTI MANUAL

2 CTENTS Preface Features Warnings & Cautions Structural Element Fast Dome Camera Set Up RS- Protocol Switch Setting Fast Dome ID Address Setting Refer Chart Fast Dome Connection Jack and Cable Requirement Installation Indoor Installation Structural Drawing Attached Mounting (Fixed Ceiling) Wall Mounting (Fixed Bracket) IP Camera System Configuration Fast Dome and Keyboard Fast Dome, Matrix and Keyboard Fast Dome with PC Control Fast Dome, DVR and Keyboard Fast Dome IP Camera with PC Control Operation Initial Power Up Inspection Manual Operation (Pan/Tilt Control) Fast Dome Selection Zoom Lens Control Focus Control (X) Iris Control Horizontal 0 Instant Flip Preset Positions Setting Recalling Preset Positions Setting Preset Group Changing Preset Data Activating Auto Pan Deleting Preset Data Setup Menu Tree Fast Dome Camera Function Setup Setup Menu Display Language Selection Camera Reset Reboot System Display System Information Display Character Setup Menu Display Dome Function Setup Menu Camera Setting Menu Display Pages

3 Display the Camera Setting Menu Auto Focus Setting Auto Iris Setting Zoom Speed Setting Focus Speed Setting Advanced Setting Exposure Mode Setting Backlight Compensation Setting White Balance Setting Auto Gain Control Setting Day/Night Control Setting Image Setting Gamma Setting Pedestal Setting Aperture Gain Setting Mirror Setting Pan/Tilt Setting Menu Display the Pan/Tilt Setting Menu Home Position Setting Self Return Time Setting Self Return Mode Setting Auto Mode Setting Auto Scan Mode Setting Preset Function Setting Menu Tour Function Setting Menu Privacy Zones Setting Menu Password Function Menu Restore Factory Defaults Schedule Setup Menu Day/Night Schedule Setting Menu Startup Auto Options Menu Daylight Saving Time Menu Specification Operational Camera Optical Lens Electrical Environmental Mechanical Appendix A Quick Reference Table Appendix B Trouble Shooting Appendix C Preset ID Characters Table

4 PREFACE SP0/ & SP/ series fast dome cameras with High resolution of 0TV lines offer significant enhancement and refinements to bring you the most innovative surveillance solutions. SP0/ & SP/ series are the leading product in the industry offering the most advanced features such as.x / X optical zoom lens, Auto White Balance mode selection, Auto Focus Control, Auto Iris Control, Day & Night Control, Infrared LED Control... Etc. LILIN's Fast Dome series measure only mm in diameter and is capable of making 0 degrees continuous rotation with a speed range of 0. to 0 degrees per second, ensures direct and accurate target positioning. When required the dome can be quickly spun through 0 degrees, an important feature when something passes directly under the camera. Up to preset positions can be programmed and recalled with an accuracy of 0. degrees. First presets can be divided into groups for auto touring with individual setting for speed and dwell time. RS- control interface makes our mini fast dome cameras easy to fit into our exist systems and compatible with other manufacturer's control systems. LILIN's Fast Dome series are fully-functional and user-friendly. It will meet your need for a wide range of surveillance applications. Fast Dome IP Camera H. AVC (Advanced Video Coding) video compression engine provides high video quality, full D resolution, bandwidth efficiency, and real-time streaming. The cutting edge of H. AVC main profile encoding technology can provide better compression rate and superior video quality at Kbps to Mbps bit rate. Dual streaming design, JPEG and H. AVC allow to stream video at low bandwidth (Internet) and high bandwidth (LAN) for optimizing video quality. Low latency design for both Intranet and Internet is a key factor of operating PTZ. Four PTZ web interfaces including lens absolution positioning are designed for easy-to-use purpose.

5 FEATURES.X Auto Focus Zoom Lens(SP0/0&IPS0/0) Build-in.X optical zoom lens with focal length. ~.mm X Auto Focus Zoom Lens(SP/&IPS/) Build-in X optical zoom lens with focal length. ~.mm 0 Horizontal TV lines Automatic Iris Control (.X Lens), Automatic / Manual Iris Control (X Lens) Preset ID / Name Private Mask 0 continuous rotation Up to programmable preset positions Preset positions auto scanning High speed rotation and tilt, speed range varies from 0. /sec ~ 0 /sec 0 Horizontal Instant Flip Build in /" CCD high resolution DSP colour camera:. Color / Mono Switch Day Color Night Mono Auto Switch from color to mono when light drops below lux Schedule Switch from color to mono by time of setup. 0 TV Lines (Color) ; 00 TV Lines (Mono). Color: 0.Lux at F.9, Mono: 0Lux [IR ] (.X Lens) Color: 0.Lux at F., Mono: 0Lux [IR ] (X Lens). On-Screen Setup Menu. White Balance Control: Auto Tracking, Manual. Back Light Compensation : On/Off. Auto Gain Control : 0dB ~ db. levels Brightness Adjustment 9. levels Pedestal Adjustment 0. Aperture Correction Adjustment High efficiency infrared LED 0nm, radiant distance - meters RS- control interface Up to Mini Fast Dome configuration Compatible with PC control (protocol required) Power supply options : 00 ~ 0VAC or VAC True H. AVC/MPEG- part 0 real-time video compression [IPS0/0//] Full D resolution at 0x0(NTSC)/0x(PAL) in live monitoring IPS0/0//] Full duplex H. AVC and JPEG streaming [IPS0/0//]

6 WARNINGS & CAUTIS Please read the manual before attempting installation or operation. Please be aware to the warnings and cautions notice.. Don't use any chemical detergent to clean the machine surface, use a damp cotton cloth only. Regularly clean the dome cover to assure proper focus ability.. Please install the Fast Dome in a dry area, water and high humidity may cause damage on internal parts. External housing should be used for outdoor installation.. Please use parts supplied by the manufacturer only, any unqualified part using in the equipment may violate the warranty.. Avoid installing the equipment in an unstable area. Make sure the area is firm and stable. Falling equipment may injure personnel and damage the equipment.. Do not install the equipment near any flammable gas. Violation may cause fire or injury.. Avoid running video cable and signal cable through or passing interference sources such as video waves, broadcast station, power generator, elevator motor or high voltage area... etc. Violation may cause interference.. Make sure the power cable is properly fixed. Un-suitably fixed cable may cause serious short circuit or fire. 9. Correct cable connection is important. Do not place any object on the connection cable and change the cable if there is damage on cable. Violation may cause short circuit, fire and injury. 0. Make sure ground is well connected to avoid damage caused by lightning.. Do not put any foreign objects inside the equipment and do not spray any liquid on equipment. This will avoid short circuit damage.. Do not touch power connection with wet hands to avoid short circuit or electricity shock.. Do not apply smash-force on the equipment. Violation may cause damage.. Do not install the equipment in a location that may expose the equipment directly to sunlight. Violation may cause colour fading or damage.. Do not install the equipment in high temperature or low temperature environment to avoid damage. The normal operational temperature is between -0 C ~ +0 C.. Fast Dome contains high sensitive electric parts inside. Do not try to repair them without qualified personnel.. Turn off the power immediately and contact the technician when the following occurs: A. Damage on power cable or plug. B. Water leak into the equipment. C. Fast Dome can not be operated normally. D. Equipment falling on ground or damage on external case. E. Unusual occurrence.. Warning: Do not try to repair the equipment. Only a qualified technician may disassemble and repair the equipment. Shut off the power before disassemble the equipment and don't put power on unless the case is completely assembled.

7 STRUCTURAL ELEMENT Camera Body Camera Case Bottom Chassis Power In DC Jack (DCV In DC Jack) RS- In/Out Terminal Video Out BNC Jack Audio In/Out Jack [IPS0/0//] RJ Jack [IPS0/0//] LED Status [IPS0/0//] [IPS0/0//]

8 FAST DOME CAMERA SET UP DIP Switch Setting RS- Protocol Switch Camera ID Switch RS- Protocol Switch Setting Explanation of DIP Switch Setting :. RS- IN-TML RES. : RS- IN Terminal Resistor /OFF. RS- OUT-TML RES. : RS- OUT Terminal Resistor /OFF. HALF / FULL : wiring system (HALF duplex) or wiring system (Full duplex). BAUD SEL : Transmission speed selection. BAUD SEL : Transmission speed selection. PROTOCOL SEL : Protocol selection. PROTOCOL SEL : Protocol selection. PROTOCOL SEL : Protocol selection RS- In/Out Terminal Resistor Setting Daisy Connection: Set RS- In and Out terminal resistor as (Factory Initialize). Parallel Connection: Set the front and last equipments terminal resistor as. The parallel connection equipment in the middle set as OFF to keep the best transmitted status.

9 RS- Communication Mode Selection DIP SWITCH wiring system (HALF duplex) wiring system (FULL duplex) OFF Communication Mode of HALF: Most of systems use this mode because of low-cost and easy setup, but this mode can't receive and transmit data simultaneously. Communication Mode of FULL: This Mode can receive and transmit data simultaneously. Transmission Speed Setting BAUD RATE SELECTI DIP SWITCH 00 bps 00 bps OFF 900 bps 900 bps OFF OFF OFF Remark: LILIN Protocol control mode is N,, Baud Rate: 900bps Protocol Setting PROTOCOL SELECTI DIP SWITCH MLP (MERIT LILIN PROTOCOL ) VERSI MLP (MERIT LILIN PROTOCOL ) VERSI OFF Remark: LILIN MLP (MERIT LILIN PROTOCOL ) is same as PIH- Fast Dome Protocol MLP (MERITLILIN PROTOCOL ) is the new protocol for controlling fast dome cameras. The protocol contains bytes which include a checksum byte and extra control codes. The check-sum byte, for example, can prevent RS- interference affecting a protocol. The extra control codes, for example, can provide the feature of controlling absolute position of a fast dome camera. RS- Protocol DIP Switch of LILIN SP0/0// & IPS0/0// Series Setting RS- Protocol DIP Switch Setting DIP SWITCH MLP Version OFF OFF MLP Version OFF OFF OFF

10 Fast Dome ID Address Setting Refer Chart Fast Dome Camera can be serial linking in one system. Therefore each dome is addressing by ID switch located. When select MLP (MERIT LILIN PROTOCOL ), Camera ID setting as followings:

11 When select MLP (MERIT LILIN PROTOCOL ), Camera ID setting as followings:

12

13

14 Fast Dome Connection Jack and Cable Requirement DCV Power Cable RS- Twisted Pair Cable Video Signal Cable Signal Shield Wire CAT Network Cable. DC Input Jack DC Input: DC V 0%. RS- In/Out Terminal RS- Input (TXDI+,TXDI-) to receiver signal from keyboard, matrix, DVR or multiplexer through twisted pair cable. RS- Output (TXDO+,TXDO-) sending out signal to next fast dome through twisted pair cable. Recommend Data Cable: VW-ISC UL AWGxC Transmission Distance: Max. kilometer. Video Out BNC Jack Video Signal Output CVBS.0Vp-p Recommend Signal Cable: CV BNC. RJ Jack [IPS0/0//] LAN : 0/00Mbps Recommend Signal Cable : CAT. Audio In/Out RCA Jack [IPS0/0//] Audio :.Vp-p ( Vrms) Recommend Signal Cable : Signal shield wire Audio In/Out Jack RJ Jack

15 INSTALLATI Indoor Installation Structural Drawing Attached Mounting

16 Attached Mounting (Fixed Ceiling) Step Fix The Metal Clips of ceiling 0 0 Put fixed metal clips on installation position of ceiling. Tighten the three tapping screws into the ceiling. Loose the screw of bottom chassis. (Don't need taking out the screw) Base size and screw location. Step Setting Fast Dome Camera Take out the screw cover s on right and left side of dome cover. Untighten the screws. Take out dome cover from top of dome camera. Setting Fast Dome ID and RS- Protocol. Step Attach the Camera and Metal Clips Putondomecoverto dome camera. Tighten the screws on right and left side dome cover. Put in screw covers. Set all of control cable on middle position and through the hole of ceiling Attach dome camera body to metal clips. Turn camera body counter clockwise to tight position. Tighten the screw to fix camera body.

17 Step Connection TXDI+ TXDI - TXDO+ TXDO - GND VIDEO OUT Connect RS- cable. Connect Video signal cable. Connect DCV of power cable. (Suggest to use the ADAPTOR from the factory) Wall Mounting (Fixed Bracket) Step Fix The Bracket Fixed bracket first, and pull control cable and power cable from bracket cable outlet. Take out connecting cable model on body bottom. Connect control cable and power cable with connecting cable model. Step Fix The Metal Clips of Bracket Take connecting cable model through the hole of metal clips. Configure the metal clips on bracket, and pull all of control cable into the bracket. Tighten the three screws to fix bracket. Loose the screw of bottom chassis. (Don't need taking out the screw)

18 Step Setting Fast Dome Camera Take out the screw cover s on right and left side of dome cover. Untighten the screws. Take out dome cover from top of dome camera. Setting Fast Dome ID and RS- Protocol. Connect the connecting cable model on body bottom. Step Attach the Camera and Metal Clips Put on dome cover to dome camera. Tighten the screws on right and left side dome cover. Put in screw covers. Attach dome camera body to metal clips. Turn camera body counter clockwise to tight position. Tighten the screw to fix camera body. Attach dome camera body to metal clips. Turn camera body counter clockwise to tight position. IP Camera Connect Ethernet cable and DCV of Power cable. (Suggest to use the ADAPTOR from the factory) Tighten the screw to fix camera body.

19 SYSTEM CFIGURATI LILIN's integrated Fast Dome Surveillance System is suitable for a wide range of surveillance applications. The system can be as single fast dome with one keyboard or encompassing as domes with comprehensive matrix switching, PC control and even Digital Video Recording. Such flexibility means future expansion is easily facilitated. Fast Dome and Keyboard Single dome configuration: One Fast Dome Camera connects to one PIH-00II or PIH-9D/9T. Telemetry control is sent via twisted pair between Dome and Keyboard. Video signal from the dome is sent to monitor or multiplexer or quad or switcher. RS- Connection st pin TXDI+ of RS- jack at back of the keyboard connects to TXDI+ of RS- jack on fast dome. nd pin TXDI- of RS- jack at back of the keyboard connects to TXDI- of RS- jack on fast dome.

20 Multiple Domes means that more than one fast dome is linked in the system. Each dome connects to next dome forming a serial linking. Each dome has an individual ID dip switch, which allows the keyboard to identify each fast dome and make command. Sometimes it is more convenient to wire a telemetry system in star configuration rather than daisy chain. To do this a PIH-0 data distributor is necessary. It takes an output from a keyboard or a matrix and splits the single data line into separate data lines. One keyboard can control up to camera. RS- Connection Between PIH-0 Data Distributor and Fast Dome st output TXDI+ of PIH-0 connects to TXDI+ of st fast dome and TXDI- of PIH-0 to TXDI-of st fast dome. Linking nd Fast Dome TXDO+ of st fast dome connects to TXDI+ of nd dome and TXDO- of st dome to TXDI- of nd dome. RS- Connection Between PIH-0 Data Distributor and Keyboard st pin TXDI+ on RS- IN jack of keyboard connects to TXDO+ on RS- OUT jack of PIH-0 nd pin TXDI- on RS- IN jack of keyboard connects to TXDO- on RS- OUT jack of PIH-0 9

21 POWER F F F F PRESET PRESET PRESET FAST ESC AUX CTRL CTRL SETUP 9 M CAM CLR 0 ENT PRESET WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN KEYPRO PIH-00 POWER F F F F PRESET PRESET PRESET FAST ESC AUX CTRL CTRL SETUP 9 M CAM CLR 0 ENT PRESET WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN KEYPRO PIH-00 Fast Dome, Matrix and Keyboard Matrix System is designed to process multiple video systems and video switching. Its central process unit (CPU) can manage multiple video signals simultaneously and control other linking system, such as fast dome or PIH-0 telemetry receiver. All telemetry remote control and signal transmissions are through twisted pair. One matrix can manageuptofastdomes. Multiple keyboards can be used for matrix control. st keyboard is the master and rests are slaves. Up to keyboards can be used in one system. Each keyboard has a Dip Switch for ID setting. (Please refer to keyboard's manual for detail) Fast Domes RS- Pan/Tilt Cameras RS- PIH-0 Receiver FAST DOME CAMERA AC MATRIX PIH-0 Receiver PAN/TITL DC V IN OUT PIH-0 Receiver TXDI+ TXDI- TXDO+ TXDO- RS- MATRIX PIH- RS- Connection Between Matrix and Fast Dome TXD+ of receiver jack on matrix connects to TXDI+ of st fast dome and TXD- of matrix to TXDI-ofstfastdome. Linking nd Fast Dome TXDO+ of st dome connects to TXDI+ of nd dome and TXDO- of st dome to TXDI- of nd dome. fast dome can be linked through the connection as shown. RS- Connection Between Keyboards TXDO+ of st keyboard RS- OUT connects to TXDI+ of nd keyboard RS- IN. TXDO- of st keyboard RS- OUT connects to TXDI- of nd keyboard RS- IN. RS- Connection Between Keyboard and Matrix TXDI+ of st keyboard RS- IN connects to st pin TXD+ of matrix's keyboard jack. TXDI- of st keyboard RS- IN connects to nd pin TXD- of matrix's keyboard jack. 0

22 Fast Dome with PC Control PC telemetry remote controls fast dome with standard RS- data format (format: N,, Baud Rate 900 bps). The PC control port RS- is converted to RS- format by interface. User may use their own software (protocol) or software provided by LILIN to control the dome. In this system up to fast domes can be linked. RS- Connection Between Fast Dome and Conversion Interface TXD+ of conversion interface RS- jack connects to TXDI+ of st fast dome and connect TXDto TXDI-. Linking nd FastDome TXDO+ of st dome RS- jack connects to TXDI+ of nd dome to TXDO- of st dome to TXDIof nd dome. fast domes can linked through the connection as shown.

23 CAMERA IN 9 0 VIDEO OUT S-VIDEO AUDIO IN AUDIO OUT LAN ALARM/RS POWER ALARM R/T POWER AC 00~0V 0/0/ PTZ MODE ID=000 OFF Fast Dome, DVR and Keyboard The DVR System is an advanced digital recording product, with long recording time and easy searching features. Telemetry remote control is twisted pair for data transmission to the fast dome. Fast Dome can be controlled directly from the control panel of the DVR, or from keyboard. Each DVR (Digital Video Recorder) can manage video signals and via RS- ot daisy connection sets of fast dome camera. VIDEO RS- DCV DVR VIDEO Camera Monitor RJ- Keyboard Controller RS- Connection Between Fast Dome and DVR TXD+ of DVR RS- jack connects to TXDI+ of st fast dome and TXD- of DVR to TXDI- of st fast dome. Linking nd FastDome TXDO+ of st dome RS- jack connects to TXDI+ of nd dome to TXDO- of st dome to TXDIof nd dome. RJ- Connection Between DVRs "Keyboard Out" of st DVR pass out RJ- jack connects to "Keyboard In" of nd DVR's RJ- jack. RJ- Connection Between DVR and Keyboard "Keyboard In" of st DVR's RJ- jack connects to RJ- jack of keyboard.

24 Fast Dome IP Camera with PC Control The Fast Dome IP Camera can be connected via RJ- cable that provides both Internet and/or Intranet access. Multiple Fast Dome IP Cameras can be connected with in a Hub or multiple Hubs. Please consult your network administrator for network architecture and software settings. VIDEO OUT RS- Ethernet cable Next Dome Internet / Ethernet RS- Connection st pin TXDI+ of RS- jack at back of the keyboard connects to TXDI+ of RS- jack on fast dome. nd pin TXDI- of RS- jack at back of the keyboard connects to TXDI- of RS- jack on fast dome. RJ- Connection Ethernet cable to Fast Dome IP Camera and attach it to the network.

25 OPERATI Initial Power Up Inspection After the power is first applied to a dome it will perform a self-test procedure. This calibrates and checks the basic functions of the dome, control is not possible during this self-test period. Once the camera has stopped moving, it will then be ready to control. If preset positions and tours have been programmed into a dome and the power is turned off, the dome will enter the Auto Scan mode once the power is turned on again (after self-test period). The dome will remain in Auto Scan until an operator cancels it. (For setting Fast Dome IP Camera other features or functions, please refer to H. IP instruction manual.) Manual Operation (Pan / Tilt Control) To control the pan and tilt movement of the dome simply use the joystick on the keyboard; to pan the camera left push the joystick to the left, to tilt down pull the joystick down (towards you). To move the dome faster push the joystick further in the that direction, the joystick is proportional to the speed of the dome; a small movement will move the dome slower. UP Push the joystick forward, the camera tilt up. DOWN Push the joystick down (towards you), the camera tilt down. LEFT Push the joystick left, the camera pan left. RIGHT Push the joystick right, the camera pan right. DIAGAL Push the joystick diagonally, the camera moves to that direction (direction on figure ) Figure Relationship Between Joystick and Direction Figure Relationship Between Joystick and Rotation Speed

26 Fast Dome Selection To call out a dome controlling or setting To select st Fast Dome Push key followed by CAM key. To select th Fast Dome Push key then followed by CAM key. PRESET When matrix system is used, select monitor before camera selection. Please refer to matrix system user manual. POWER F F F F PRESET PRESET FAST ESC CLR CAM ESC 0 REV AUX LIGHT CTRL CTRL SETUP 0 9 ENT M CAM PRESET LENS SPEED WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN Zoom Lens Control To Zoom In Push ZOOM IN key. The viewing angle becomes narrower and target will become enlarged on the screen. Zooming will stop when the key is released. To Zoom Out Push ZOOM OUT key. The viewing angle becomes wider and target will become smaller on the screen. Zooming will stop when the key is released. POWER F F F F PRESET PRESET PRESET FAST ESC CLR CAM ESC 0 REV AUX LIGHT CTRL CTRL SETUP 0 9 ENT M CAM PRESET LENS SPEED WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN Focus Control (X) The focus function on Fast Dome can be set as Auto Focus or Manual Focus. Manual focus far Push FOCUS FAR key. The target will become farther. Focusing will stop when the key is released. Manual focus near Push FOCUS NEAR key. The target will become nearer. Focusing will stop when the key is released. POWER F F F F PRESET PRESET PRESET FAST ESC CLR CAM ESC 0 REV AUX LIGHT CTRL CTRL SETUP Auto Focus Push FOCUS key. The lens will automatically adjust itself for optimum focus. 0 9 ENT M CAM PRESET LENS SPEED WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN

27 POWER Iris Control The purpose of iris control is to adjust brightness on target. It can be set as Auto Iris or Manual Iris. Iris Open (X) Push O key, to open the iris and brighten the picture. Iris will stop when the key is released. Iris Close (X) Push C key, to open the iris and reduce glare. Iris will stop when the key is released. Auto Iris Push key, to select the Auto Iris mode. F F F F PRESET PRESET PRESET FAST ESC CLR CAM ESC 0 REV AUX LIGHT CTRL CTRL SETUP 0 9 ENT M CAM PRESET LENS SPEED WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN Horizontal 0 Instant Flip Some times it is hard to use the joystick to control the camera tracking the target directly under the camera. The instant flip key can rotate the camera 0 instantly. This allows the camera continue to track the target passing directly under the camera. Two ways to operate 0 instant flip: 0 REV Push key on keyboard to flip the camera 0 CTRL horizontally. Push joystick down to bring the camera down to the end, release the joystick and quickly push joystick down twice to flip the camera 0 horizontally. POWER F F F F PRESET PRESET PRESET FAST ESC CLR CAM ESC 0 REV AUX LIGHT CTRL CTRL SETUP 0 9 ENT M CAM PRESET LENS SPEED WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN Preset Positions Setting Each dome can have individual preset positions. Each preset stores the exact position of the camera and automatic pan, tilt,zoom, focus and iris setting. Once the data is set, the preset can be recalled for viewing, or the presets can be set for auto pan. Only the first preset positions of fast dome can be set to auto pan mode. Selecting Fast Dome Push key followed by CAM key, confirming that first camera is selected. Ex. To select st fast dome : CAM keys To select th fast dome :CAMkeys Selecting Preset Position Push key followed by CAM key, confirming that first preset position selected. Ex. To select the st preset position : PRESET keys To select the th preset position :PRESETkeys

28 Joystick Control Move the Joystick to bring the camera to the desired view position. Adjusting Lens ZOOMIN/OUT,FOCUSNEAR/FAR/andO/C/keys. When set up preset point, using manual focus will F F ESC POWER AUX LIGHT CTRL provide both clarity and stability of image. F F CAM ESC 0 REV CTRL SETUP LENS SPEED WIPER SEQ SPRAY ALARM RESET PAN M ZOOM IN ZOOM OUT PRESET PRESET 9 CAM FAR NEAR PRESET FAST CLR 0 ENT PRESET O C Setting Preset Speed The speed the dome travels to that preset position can be adjusted between to 0 per second (the factory default is 0 /sec). Tosetspeedas0/sec:Pushkey0followedby CAM ESC 0 REV LENS SPEED F F ESC SPRAY POWER AUX LIGHT CTRL CTRL WIPER PAN F key, two beeps will be heard confirming that ALARM F F SETUP SEQ RESET ZOOM ZOOM speed is set. M IN OUT PRESET PRESET 9 CAM FAR NEAR Note: Push F key again to confirm speed entered. PRESET FAST CLR 0 ENT PRESET O C Setting Preset Dwell Time The dwell time means the time user wants to view on certain preset position under Auto Pan. The Preset Dwell Time can be set between0~seconds. (The factory default is 0 second) If the dwell is set to 0 second then that position will be omitted from the Auto Scan Tour. To set dwell to seconds: Push key followed by CAM ESC 0 REV LENS SPEED F F ESC SPRAY POWER AUX LIGHT CTRL CTRL WIPER PAN F key. ALARM F F SETUP SEQ RESET Ex. To set dwell to second :Fkeys ZOOM ZOOM M IN OUT PRESET PRESET 9 CAM To set dwell to 0 second :0Fkeys FAR NEAR Storing Preset Data Once the above steps have been completed, the information must be stored or it will not be memorized by the system. CAM ESC 0 REV LENS SPEED F F ESC SPRAY Push key followed by F key, two beeps will POWER AUX LIGHT CTRL CTRL WIPER ALARM be heard confirming that data is stored. F F SETUP SEQ RESET Note : For the first presets on each dome, the PRESET FAST CLR 0 ENT PRESET O C above steps must be repeated. For presets ~ there is a default speed and dwell setting so steps and are not required. PRESET PRESET FAST PRESET CLR 0 ENT 9 PRESET M CAM O ZOOM IN FAR C ZOOM OUT NEAR PAN

29 Recalling Preset Positions Once the required preset positions have been stored in a dome, they may be quickly recalled, returning the dome to exact position. To recall st Preset Position: Push key followed by PRESET key. The dome will move to that position in speed of 0 /sec. Ex. To recall st preset position : PRESET keys To recall th preset position :PRESETkeys Setting Preset Group The purpose of setting preset group allows the management of the preset positions before Auto Scanning. The first preset positions of each dome are separated into groups. Preset group must be set for the auto pan reference. Group includes: st nd rd and th preset positions. Group includes: th th th and th preset positions. Group includes: 9th 0th th and th preset positions. Group includes: th th th and th preset positions. To set up group : Push key followed by F key. Ex. To set Group F To set Group, F To set Group, F To set Group,, F To set Group,, F To set Group,,, F POWER F F F F PRESET PRESET PRESET FAST ESC CLR CAM ESC 0 REV AUX LIGHT CTRL CTRL SETUP 0 9 ENT M CAM PRESET LENS SPEED WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN Changing Preset Data In order to change any preset position from the one stored, the dome must first be sent to that preset position. To change the th preset position of the Dome number, perform the following steps: Push CAM to select Dome Push PRESET to go to th preset position Move joystick to bring camera to the desired view position. Adjusting lens Setting preset speed Setting dwell time Store Data (Please refer to preset position setting for step ~ )

30 Activating Auto Pan When the Auto Pan function is activated, the fast dome will auto touring the preset groups entered. To activate Auto Pan: Push PAN key, confirming the activation of autopan. (Auto Pan Led will be lit.) To stop Auto Pan: Push PAN key again, confirming the stop of autopan. (Auto Pan Led will be Off.) POWER F F F F PRESET PRESET PRESET FAST ESC CLR CAM ESC 0 REV AUX LIGHT CTRL CTRL SETUP 0 9 ENT M CAM PRESET LENS SPEED WIPER SEQ ZOOM IN FAR O SPRAY ALARM RESET ZOOM OUT NEAR C PAN If the PAN is activated, no other commands can be sent to that dome, but other dome can still be selected and operated manually. To select (call out) another dome while it is under Auto Pan mode: Simply push the numeric key followed by the CAM key. Push key followed by CAM key, confirming the nd camera is selected. Deleting Preset Data Sometimes it is necessary to delete the stored data. All the data can be cleared from a dome by pressingkey90,followedbytheclrkey. POWER F F ESC CAM ESC 0 REV AUX LIGHT CTRL CTRL LENS SPEED WIPER SPRAY PAN All preset data will be erased. Push90,followedbyCLRkey. F F PRESET PRESET PRESET FAST CLR SETUP M 9 CAM 0 ENT PRESET SEQ ZOOM IN FAR O ALARM RESET ZOOM OUT NEAR C 9

31 SETUP MENU TREE SETUP MENU LANGUAGE DISPLAY SETUP PRESET ID ZOOM RATIO DATE/TIME TIME DATE DATE FORMAT PAN/TILT ANGLE AREA TITLE DOME SETTINGS CAMERA FOCUS (X) LEVEL ZOOM SPEED FOCUS SPEED (X) ADVANCED SETTING EXPOSURE MODE MANUAL BACKLIGHT BLC GAIN ADJ. WHITE BALANCE ATW MWB GAIN CTROL DAY/NIGHT SCHED DAY NIGHT IMAGE GAMMA PEDESTAL APERTURE GAIN MIRROR PAN/TILT HOME POSITI SELF RETURN TIME SELF RETURN MODE MODE EDIT POSITI DWELL TIME SCAN SPEED PRESETS PRESET NUMBER PRESET MAP EDIT POSITI EDIT ID DWELL TIME SPEED CLR PRESET 0

32 TOURS NUMBER EDIT TOUR CLEAR ABOVE NUMBER DWELL TIME SPEED PRIVACY ZES NUMBER EDIT ZE CLEAR PASSWORD ENABLE PASSWORD EDIT PASSWORD FACTORY INITIAL CAMERA ALL SCHEDULE SETUP DAY/NIGHT DAY NIGHT NIGHT DAY STARTUP OPTIS DAYLIGHT SAVING TIME.HH:MM.HH:MM.HH:MM.HH:MM.HH:MM.HH:MM.HH:MM.HH:MM STARTUP. START. END. START. END. START. END SYSTEM INFORMATI CAMERA RESET REBOOT SYSTEM BACK EXIT

33 Fast Dome Camera Function Setup Fast Dome Camera/Fast Dome IP Camera (build-in.x/x optical zoom lens) series provide on-screen display (OSD) setup menu, all functions can be selected and set via OSD Setup Menu. Setup Menu Display Press key on the keyboard to recall Setup Menu. CTRL Press ESC key to exit setup menu or push joystick down to select <EXIT>, and then press keytoexitsetupmenu. CTRL LANGUAGE ENGLISH <DISPLAY SETUP> <DOME SETTINGS> <SCHEDULE SETUP> <SYSTEM INFORMATI> <CAMERAS RESET> <REBOOT SYSTEM> EXIT MERIT LILIN FAST DOME NOTE Buttons Description MLP MLP PIH-9D/9T PIH-00III PIH-9D/9T PIH-00III Enter Setup Menu C. SET CTRL CTRL SET SETUP Exit Setup Menu C. ESC LIGHT CAM ESC LIGHT ESC ESC Language Selection Press key into Setup Menu. CTRL Push joystick down to select <LANGUAGE>, and then push joystick left or right to make selection. Press ESC key to exit setup menu or push joystick down to select <EXIT>, and then press CTRL keytoexitsetupmenu. Camera Reset Restart camera module to perform initial setting of camera. Press key into Setup Menu. CTRL Push joystick down to select <CAMERA RESET>, and then press CTRL key to restart camera. Press ESC key to exit setup menu or push joystick down to select <EXIT>, and then press keytoexitsetupmenu. CTRL Reboot System Restart the fast dome system to perform initial setting and behavior. Press key into Setup Menu. CTRL Push joystick down to select <REBOOT SYSTEM>, and then press key to restart the fast CTRL dome system. Press ESC key to exit setup menu or push joystick down to select <EXIT>, and then press CTRL keytoexitsetupmenu.

34 Display System Information Press key into Setup Menu. CTRL Push joystick down to select <SYSTEM INFORMATI>, and then press key to display CTRL current system information. Push joystick down to select <BACK>, and then press key to go back or push joystick down CTRL to select <EXIT>, and then press key to exit setup menu. CTRL MERIT LILIN FAST DOME SYSTEM INFORMATI LANGUAGE ENGLISH <DISPLAY SETUP> <DOME SETTINGS> <SCHEDULE SETUP> <SYSTEM INFORMATI> <CAMERAS RESET> <REBOOT SYSTEM> EXIT DOME MODEL CAMERA VER. PAN/TILT VER. RECEIVER VER. FT VER. COMM DOME ADDR. PROTOCOL BACK EXIT SP0X , n,, LILIN MLP Display system information:. Fast dome model number. Camera, Pan/Tilt, Receiver version. Font of OSD version. Protocol rate and format. Fast dome ID number. Protocol version, LILIN (LILIN MLP), LILIN MLP Display Character Setup Menu. Display Character Setup Menu Press key into Setup Menu. CTRL Push joystick down to select <DISPLAY SETUP>, and then press key to display character CTRL setup menu. Push joystick down to select <BACK>, and then press key to go back or push joystick down CTRL to select <EXIT>, and then press key to exit setup menu. CTRL MERIT LILIN FAST DOME LANGUAGE ENGLISH <DISPLAY SETUP> <DOME SETTINGS> <SCHEDULE SETUP> <SYSTEM INFORMATI> <CAMERAS RESET> <REBOOT SYSTEM> DISPLAY SETUP PRESET ID ZOOM RATIO DATE/TIME PAN/TILE ANGLE AREA TITLE OFF OFF OFF OFF OFF EXIT BACK EXIT. Preset ID setting Push joystick down to select <PRESET ID>, and then push joystick left or right to make selection: OFF:NoPresetIDonthemonitorscreen. ~ sec : Display elapsed time. Preset ID will have been displayed on the monitor screen until elapsed time stops, when Preset ID is recalled.

35 . Zoom Ratio Setting Push joystick down to select <ZOOM RATIO>, and then push joystick left or right to make selection: OFF : No Zoom Ratio on the monitor screen. ~ sec : Display elapsed time. Zoom Ratio will have been displayed on the monitor screen until elapsed time stops, when Zoom Ratio is operated.. Date and Time Setting Push joystick down to select <DATE/TIME>, and then push joystick left or right to make selection: OFF : No Date/Time on the monitor screen. : Display Date/Time on the monitor screen. When selection is open, and then press CTRL key, date/time will be set. DISPLAY SETUP DATE/TIME PRESET ID ZOOM RATIO DATE/TIME PAN/TILE ANGLE AREA TITLE OFF OFF <> OFF OFF TIME DATE DATE FORMAT :00:0 0/0/0 yy/mm/dd BACK EXIT BACK EXIT () Time Adjustment Push joystick down to select <TIME>, and then press CTRL key to setup time. Push joystick left or right to adjust time, and then press key to next item of time. CTRL :00:0 :00:0 :00:0 :00:0 CTRL CTRL CTRL () Date Adjustment Push joystick down to select <DATE>, and then press CTRL key to setup date. Push joystick left or right to adjust date, and then press key to next item of date. CTRL 0:0:0 0:0:0 0:0:0 0:0:0 CTRL CTRL CTRL () Date Format Setting Push joystick down to select <DATE FORMAT>, and then push joystick left or right to adjust format of date. yy/mm/dd mm/dd/yy dd/mm/yy. Pan/Tilt Angle Setting Push joystick down to select <PAN/TILT ANGLE>, and then push joystick left or right to select pan/tilt setup: OFF : No Pan/Tilt Angle on the monitor screen. : Pan/Tilt Angle on the monitor screen.

36 . Area Title Setting The area title function lets you display a direction indicator that appears in the picture to indicate the direction of the location being shown on the screen. Text can also be displayed in the place of the direction indicators, if desired. The direction indicators are N(north), NE(northeast), E(east), SE(south east), S(south), SW(southwest), W(west) and NW(northwest). Push joystick down to select <AREA TITLE>, and then push joystick left or right to select area title setup. OFF : Turn off display of area title direction indicators and text. NESW : Displays direction indicators. Select(NESW) and pressing the CTRL button will display the position(nesw) setting menu. Which you can use for configuring detailed settings. USER : Display user input text. Selecting(USER) and pressing the button will display the CTRL area title(user) selection menu, which you can use for configuring detailed settings. () When NESW is selected After selecting NESW, you can use the joystick to configure detailed setting. Once you set the northerly(n) direction for camera, all other directions are displayed automatically. () When USER is selected After selecting USER, you can use the area title USER setting menu to configure detailed settings. You can use following procedure to configure direction settings, and to input text associated with a particular direction indicator. USER AREA AREA NUMBER <EDIT POSITI> <EDIT TITLE> CLR AREA ABOVE NUM BACK EXIT. Push joystick down to select <AREA NUMBER>, and then push joystick left or right to select area number. (~). Push joystick down to select <EDIT POSITI>, and then press key into Area CTRL Position setting. Push joystick left, right, up or down to start position, and ZOOM IN, ZOOM OUT to adjust zoom, then press key to confirm. CTRL. Push joystick down to select <EDIT TITLE>, and then press key into title setup. ID FOR AREA NUM. 0 CTRL CHARACTER EDIT AREA COMMAND SPACE COPY OK BACKSPACE CANCEL

37 () New Area Title Editing Push joystick down to select character, and press key to confirm. The character CTRL selected will be showed in edit area. If you need space, push joystick down to select <SPACE> and press key to confirm. CTRL Press O or C to switch to next character list. Repeat all steps to complete Area Title. () Copy Area Title to Another Area Push joystick down to select <EDIT AREA>, and push joystick left or right to select first copy of characters. Push joystick down to <COPY>, and press key to confirm. At this time first CTRL character of Area ID will be copy to first character position of another Area Title, andpress keytodonextcopy. CTRL Push joystick down to <OK>, and press key for exit. Select another area on the CTRL area menu, and get into area title setting. Then push joystick down to "EDIT AREA" and press key for copy. At this time edit area will show area title that was copied. CTRL () Modify Area title Push joystick down to select <EDIT AREA> on the area title setting, and push joystick right to select modifiable characters. Push joystick down to select new characters, and press CTRL key to chose. () Cancel Area Title Push joystick down to <CANCEL>, and then press CTRL key to cancel area title. () Return Preset Menu Push joystick down to "OK", and then press key to back to user area menu.. Clear Area Title Push joystick down to select <CLR AREA>, and then push joystick left or right to select <ABOVE NUM> or <ALL>. Then press CTRL ABOVE NUM : Only clear character of allotted area. ALL : Clear character off all area. CTRL key to confirm.. Character Location Date / Time 00/0/0 00:00:0 Preset ID Auto Mode Message Horizontal Angle CAM 00 Outdoor Auto Mode SEQ. 0deg 90deg.0x Vertical Angle Zoom Ratio

38 Display Dome Function Setup Menu Press key into Setup Menu. CTRL Push joystick down to select <DOME SETTINGS>, and then press menu. CTRL key into dome setting MERIT LILIN FAST DOME LANGUAGE ENGLISH <DISPLAY SETUP> <DOME SETTINGS> <SCHEDULE SETUP> <SYSTEM INFORMATI> <CAMERAS RESET> <REBOOT SYSTEM> DOME SETTING <CAMERA> <PAN/TILT> <PRESETS> <TOURS> <PRIVACY ZES> <PASSWORD> <FACTORY INITIAL> EXIT BACK EXIT Camera Setting Menu Display. Display the Camera Setting Menu After getting in dome setting menu, push joystick down to select <CAMERA>, and then press key into camera setting menu. CTRL CAMERA CAMERA LEVEL ZOOM SPEED <ADVANCED SETTING> 0 FOCUS LEVEL ZOOM SPEED FOCUS SPEED <ADVANCED SETTING> BACK EXIT BACK EXIT.X X () Auto Focus Setting Push joystick down to select < FOCUS>, and then push joystick left or right to select auto focus mode: Auto : Keep performing auto focus function for object. One push : Fast Dome will only auto "one push" focus on object under Auto panning or Manual Zoom In / Zoom Out. () Auto Iris Setting Push joystick down to select < LEVEL>, and then push joystick left or right to adjust auto iris level. Autoirislevelsare0~. () Zoom Speed Setting Push joystick down to select <ZOOM SPEED>, and then push joystick left or right to adjust zoom speed setting. [.X] Zoom speed ranges are~. [X] Zoom speed ranges are~.

39 () Focus Speed Setting Push joystick down to select <FOCUS SPEED>, and then push joystick left or right to adjust focus speed setting. Focusspeedrangesare~.. Advanced Setting After getting in camera setting menu, push joystick down to select <ADVANCED SETTING>, and then press key into advanced setting. CTRL ADVANCED SETTING EXPOSURE MODE BACKLIGHT WHITE BALANCE GAIN CTRL DAY/NIGHT <IMAGE> <MANUAL> <> ATW 0 db BACK EXIT () Exposure Mode Setting Push joystick down to select <EXPOSURE MODE>, and then push joystick left or right to setup auto mode or manual mode. EXPOSURE : This mode will automate to select shutter speed by brightness variation to exhibit image effect of high brightness area. MANUAL EXPOSURE : This mode can set a fixed shutter speed with iris to exhibit image effect. Press key into Manual Exposure Setting, and then push joystick left or right CTRL to made selection. /0(0) /00(0) /0 /00 /00000 /0000 /000 /000 MANUAL EXPOSURE SHUT SPEED /0 BACK EXIT

40 () Backlight Compensation Setting BLC GAIN ADJUSTMENT Push joystick down to select <BACKLIGHT>, and then push GAIN 9 joystick left or right to select "" or "OFF". : The brightness gain is automatically controlled for backlight compensation in response to the light intensity detection window. BACK EXIT When selection is "", press key into BLC CTRL setting menu. Push joystick down to select <GAIN>, and then push joystick left or right to select gain steps. (0 ~ 0) () White Balance Setting Push joystick down to select <WHITE BALANCE>, and then push joystick left or right to select white balance mode. ATW: Auto Tracing White Balance, suitable for 00~900K color temperature environment. MWB: Manual White Balance, suitable for 00~900K color temperature environment. Select <MWB>, and press key into MWB CTRL adjustment image. MWB ADJUSTMENT RGAIN Push joystick down to select <R GAIN>, and then push BGAIN joystick left or right to adjus the low color temperature. Push joystick down to select <B GAIN>, and then push joystick left or right to adjus the high color temperature. BACK EXIT () Auto Gain Control Setting Push joystick down to select < GAIN CTRL>, and then push joystick left or right to make selection. Auto Gain Control ranges are 0dB ~ db. () Day/Night Control Setting Push joystick down to select <DAY/NIGHT>, and then push joystick left or right to select mode. SCHED. DAY NIGHT : [.X] When light level is over lux, camera switches DAY automatically to produce color image. When light drops below lux, camera switches NIGHT automatically to produce monochrome image. [X] When light level is over 0 lux, camera switches DAY automatically to produce color image. When light drops below lux, camera switches NIGHT automatically to produce monochrome image. 9

41 When selection is "", press key into CTRL DAY/NIGHT setting menu. Push joystick down to select <SENSITIVITY>, and then push joystick left or right to select sensitivity steps. ( ~ ) DAY/NIGHT SENSITIVITY BACK EXIT SCHED. : DAY/NIGHT switch automatically between Day mode and Night mode by schedule of time setting. DAY : Set to DAY mode and always produce constant color image. NIGHT : Set to NIGHT mode and always produce constant monochrome image.. Image Setting After getting in advanced setting menu, push joystick down to select <IMAGE>, and then press key into image setting menu. CTRL IMAGE GAMMA PEDESTAL APERTURE GAIN MIRROR OFF BACK EXIT () Gamma Setting Push joystick down to select <GAMMA>, and then push joystick left or right to make selection. (0 ~ ) () Pedestal Setting Push joystick down to select <PEDESTAL>, and then push joystick left or right to make selection. (0 ~ ) () Aperture Gain Setting Push joystick down to select <APERTURE GAIN>, and then push joystick left or right to make selection. (0 ~ ) () Mirror Setting Push joystick down to select <MIRROR>, and then push joystick left or right to make selection. ("OFF" or "") Note: Image will be Left/Right reverse. Pan/Tilt Setting Menu. Display the Pan/Tilt Setting Menu After getting in dome setting menu, push joystick down to select <PAN/TILT>, and then press key into pan/tilt setting menu. CTRL 0

42 PAN/TILT HOME POSITI SELF RETURN TIME SELF RETURN MODE MODE OFF OFF OFF SEQ. BACK EXIT. Home Position Setting Push joystick down to select <HOME POSITI>, and then push joystick left or right to select home position. OFF: NO action. ~ : Home positions are preset position from fast dome. Note: When keyboard control isn't used, "Return Mode" is set for "HOME" and "Return Time" is over, "Return Mode" function will be started.. Self Return Time Setting Push joystick down to select <SELF RETURN TIME>, and then push joystick left or right to select return time. OFF: NO action. ~ 90: Delay time of return time setting is ~90 min. Note: When keyboard control isn't used, "Return Time" is also over, "Return Mode" function will be started.. Self Return Mode Setting Push joystick down to select <SELF RETURN MODE>, and then push joystick left or right to select return mode. OFF HOME SEQ. TOUR TOUR OFF: NO action. HOME: Perform return home position mode. : Perform auto scan mode. SEQ.: Perform preset group mode. TOUR: Perform tour list mode. TOUR: Perform tour list mode Note: When keyboard control isn't used and "Return Time" is also over, "Return Mode" function will be started.. Auto Mode Setting Push joystick down to select < MODE>, and then push joystick left or right to select mode. OFF SEQ. TOUR TOUR

43 OFF: NO action. : Perform auto scan mode. SEQ.: Perform preset group mode. TOUR: Perform tour list mode. TOUR: Perform tour list mode Note: Press key on the keyboard to perform Auto mode function. PAN. Auto Scan Mode Setting Push joystick down to select < MODE> or <SELF RETURN MODE>, and then push joystick left or right to select <>, then press key into auto scan mode setting. CTRL SCAN <EDIT POSITI> DWELL TIME SCAN SPEED Sec 0 deg/sec BACK EXIT () Position of Auto Pan Setting Push joystick down to select <EDIT POSITI>, and then press key into setting CTRL menu. ZOOM ZOOM Push joystick left, right, up or down to select start position, and then press IN, OUT, FOCUS FOCUS,,, to adjustzoom,focus,iris,thenpress keytoconfirm. FAR NEAR O C CTRL Push joystick left, or right to select end position, and then press key to confirm. CTRL () Dwell Time Setting Push joystick down to select <DWELL TIME>, and then push joystick left or right to select dwell time. ( ~ sec) () Scan Speed Setting Push joystick down to select <SCAN SPEED>, and then push joystick left or right to select scan speed. ( ~ 0 deg/sec) Preset Function Setting Menu. Display the Preset Setting Menu After getting in dome setting menu, push joystick down to select <PRESETS>, and then press key into presets setting menu. CTRL

44 PRESETS PRESET NUMBER <PRESET MAP> <EDIT POSITI> <EDIT ID> DWELL TIME SPEED CLR PRESET sec 0 deg/sec ABOVE NUM. BACK EXIT. Select Preset Numbers () Select number by PRESET NUMBER Push joystick down to select <PRESET NUMBER>, and then push joystick left or right to select preset number. ( ~ ) () Select number by PRESET MAP Push joystick down to select <PRESET MAP>, and then press key into preset map. CTRL Push joystick left, right, up or down to select preset number, and then press key into CTRL preset setting menu. If need to select preset numbers ~, push joystick down to <~>, and then press key into preset numbers ~. CTRL PRESET POSITI <-> <-9> <9-> BACK EXIT PRESET NUMBER <PRESET MAP> <EDIT POSITI> <EDIT ID> DWELL TIME SPEED CLR PRESET BACK PRESETS EXIT sec 0 deg/sec ABOVE NUM.. Preset Position Setting Push joystick down to select <EDIT POSITI>, and then press key into preset position CTRL setting. Push joystick left, right, up, or down to select preset position ZOOM ZOOM FOCUS Push joystick left, right, up, or down to select start position, and then press,,, IN OUT FAR,, to adjust zoom, focus, iris, then press key to confirm. FOCUS NEAR O C CTRL. Preset ID Setting Push joystick down to select <EDIT ID>, and then press ID FOR PRESET NUM. 0 CTRL key into preset ID setup. CHARACTER EDIT AREA COMMAND SPACE POSI OK BACKSPACE COPY CANCEL

45 () New Preset ID Editing Push joystick down to select character, and press key to confirm. The character CTRL selected will be showed in edit area. If you need space, push joystick down to select <SPACE> and press key to confirm. CTRL Press O or C to switch to next character list. Repeat all steps to complete preset ID. () Copy preset ID to Another Preset Push joystick down to select <EDIT AREA>, and push joystick left or right to select first copy of characters. Push joystick down to <COPY>, and press key to confirm. At this time first CTRL character of preset ID will be copy to first character position of another preset ID, and press CTRL keytodonextcopy. Push joystick down to <OK>, and press key for exit. Select another preset on the CTRL preset menu, and get into preset ID setting. Then push joystick down to "EDIT AREA" and press key for copy. At this time edit area will show preset ID that was copied. CTRL () Modify Preset ID Push joystick down to select <EDIT AREA> on the preset ID setting, and push joystick right to select modifiable characters. Push joystick down to select new characters, and press key to chose. CTRL () Cancel Preset ID Push joystick down to <CANCEL>, and then press CTRL key to cancel preset ID. () Preset ID Position Setting Push joystick down to "POSI", and then press key to get in. CTRL Push joystick to move preset ID to needful position of frame, and then push confirm. CTRL key to () Return Preset Menu Push joystick down to "OK", and then press CTRL key to back to preset menu.. Dwell Time Setting Push joystick down to select <DWELL TIME>, and then push joystick left or right to select needful dwell time. ( ~ sec) Note: Only preset No.~ can set dwell time, because group of auto pan can only edit preset No.~. Other preset numbers can't set dwell time.