Gerber X2 Setup. Summary. Modified by Jason Howie on Mar 10, Parent page: WorkspaceManager Dialogs

Transcription

1 Gerber X2 Setup Modified by Jason Howie on Mar 10, 2015 Other Related Resources Gerber Setup (Dialog) Parent page: WorkspaceManager Dialogs The Gerber X2 Setup dialog. Summary This dialog allows the designer to specify the layers to be plotted, and configure related additional options, when generating output from the active PCB in Gerber X2 format. Gerber X2 is a direct, and much advanced, evolution of the existing Gerber RS-274X standard and adds a large range of additional data for PCB fabrication and assembly. A prime advantage of the Gerber X2 format is backward compatibility with the older Gerber RS-274X standard. Being a multi-file standard, a target fab/assembly house that has not moved to the new standard can extract the traditional Gerber file elements as needed. This may be a significant advantage for those unwilling to tackle a major shift in fabrication file formats, or for fabrication houses with inflexible equipment and software.

2 Access The dialog is accessed from the PCB Editor by clicking Outputs Fabrication main menus., from the Options/Controls Units Use this region to choose the inherent units used in the generated file: Format Inches - enable this option to use imperial units, where all work is done in mils (1/1000 inch). Millimeters - enable this option to use metric units, where all work is done in millimetres. Use this region to specify the numerical precision of the plot coordinates in the Gerber file. The following precisions are supported: 2:3 - providing a resolution of 1 mil (1/1000 inch). 2:4 - providing a resolution of 0.1 mil. 2:5 - providing a resolution of 0.01 mil. 2:6 - providing a resolution of mil. The first number represents the number of digits before the decimal point, and the second is the number of digits after the decimal point. With the 2:3 format for example, the largest number in the Gerber file could be inches and the smallest number could be inches (1 mil). The format is selected to suit the placement precision of the objects in the PCB workspace and/or fabricator preferences (normally set to the highest resolution: 2:6) Aperture Tolerances Use the options in this region to set the tolerance range used when matching apertures for each item in the plots. Plus - define the positive tolerance for aperture matching. Minus - define the negative tolerance for aperture matching. If no exact match for an item is available in the current aperture list, the software checks to see if a slightly smaller or larger aperture exists within this tolerance range and uses it instead. If no suitable aperture exists within the tolerance range, the software will attempt to paint with a smaller aperture to create the required shape. This requires that a suitable smaller aperture is available, and that this aperture can be used for painting. Note: Aperture match tolerances are normally only used when targeting a vector photoplotter, which require a fixed, or supplied aperture file. They will not be required if the apertures have been created from the PCB and flashed. If match tolerances are not

3 required they should be left at the default of mil. Plotter Type Use this region to specify the target photoplotter type: Unsorted (raster) - use raster machine (default). Sorted (vector) - use vector machine. Gerber files can be created with the data sorted by its position on the film, or unsorted. Sorting is only required by vector photoplotters and does not apply to modern raster-style plotters which create an initial image internally. If sorting is enabled Gerber generation may take an extended time. Other Optimize change location commands when this option is enabled, X or Y location data is not included if it does not change from one object to the next. Generate DRC Rules export file (.RUL) - enable this option to generate a DRC Rules Export file. The report details the design rules defined for the source PCB document from which the Gerber data is being generated. Gerber X2 Specific File Subject use this field to nominate the file type, which is included as a Part attribute in the Gerber X2 outputs. The field's drop-down list provides the following choices: None Autodetect automatically assigns an attribute from the below list, based on the type of board file. For example, a PCB document containing a single board design will be assigned the Single part attribute. Single a Single PCB. CustomerPanel a board array or shipping panel. ProductionPanel a working panel or fabrication panel. Coupon a Coupon (performance test board associated with a main board design). Other none of the above. In the file, a string appended to the attribute informally indicates the part. File Comment enter a comment that will be included as an attribute in the generated outputs. Layers To Plot

4 All layers for the current board design are listed on the Layers To Plot tab. This tabbed region of the dialog allows you to configure which layers to plot in the Gerber X2 output for the current PCB document. Layers List - a listing of layers in the current PCB. Each layer is presented in terms of the following: File name the individual Gerber output file name. This uses a naming convention that is indicative of the file s function and uses a.gbr extension. Naming is based on the project name, layer and function, and uses an underscore character as a descriptive separator. Layer Name the layer name that applies to the output file, as defined by the board s layer stack. Plot enable this option to include a Gerber plot for that layer in the generated output. Disable to exclude the plot from being generated for that layer. Plot Layers - click this button to access a menu of commands that allow the Plot field for all layers in the list to be enabled/disabled en-masse: All On - use this command to enable the Plot option for all layers, (create Gerber plots for all listed layers). All Off - use this command to disable the Plot option for all layers, (create no Gerber plots). Used On - use this command to enable the Plot option for all used layers, (create Gerber plots for all listed layers that are actively being used in the design). The bulk plot selections can also be accessed from the right-click context menu. Any invalid layers (violating layers) in the layer stack are displayed in red.

5 Drills All relevant Drill files for the current board design are listed on the Drills tab. This tabbed region of the dialog includes the relevant drill files that will be generated for the current board design, which can be selected for generation on an individual or group basis. Drills List - a listing of drill files for the current PCB. This includes Drill drawing and Guide outputs. A drill drawing is a plot of the location of each drill site on the PCB, with each drill size plotted with a different symbol, whereas a drill guide marks each site with a small cross. Separate files are also available for plated and non-plated through-holes, and blind/buried vias if included in the design. Each drill file is presented in terms of the following: File Name the individual Drill output file name, constructed to comply with the Gerber X2 standard. Drill Layer Pair the Layer Pair that is associated with the drill holes file. Layer Pairs are configured in the Drill Pair Manager, accessed from the Layer Stack Manager. Plot enable this option to include a Gerber plot for that drill file in the generated output. Disable to exclude the plot from being generated for that drill file. Note that the Plot checkbox associated with each file type heading (Drill drawing, Drill guide etc) toggles the selection of all files in that section. Plot Drills - click this button to access a menu of commands that allow the Plot field for all drill files in the list to be enabled/disabled en-masse: All On - use this command to enable the Plot option for all drill files, (create Gerber plots for all listed drill files). All Off - use this command to disable the Plot option for all drill files, (create no Gerber plots). Used On - use this command to enable the Plot option for all used drill files, (create Gerber plots for all listed drill files that are actively being used in the design). The bulk plot selections can also be accessed from the right-click context menu.

6 Source URL: up))_pw