XTOOL USER MANUAL. Article No: RGB-RD-UM-XTOOL E001 Revision No: V1.1
|
|
- Clifford Doyle
- 5 years ago
- Views:
Transcription
1 XTOOL USER MANUAL Article No: RGB-RD-UM-XTOOL E001 Revision No: V1.1
2 CONTENTS CONTENTS...1 Chapter 1 Software Overview...1 Chapter 2 Installing Software... 2 Chapter 3 Using Software Connection Version... 8 VENUS X1PRO Software Upgrade...8 VSP 628PRO Software Upgrade Toolbox Custom OSD Custom Mask Custom Logo Custom Still Language Help New File Chapter 4 Contact Us Chapter 5 Revision History
3 Chapter 1 Software Overview XTOOL is the newly developed upgrade tool of RGBlink. It supports the mainstream products of RGBlink, and can realize the visual control and management on Windows or macos system. Every device has different ways for upgrade, but XTOOL eliminates the diversity and makes the upgrade easier. Features: 1) Unified interface and style; 2) Upgrade for different devices; 3) OSD, Mask, Logo and Still settings; 4) Language switcher; 5) Visual control; 6) Support Windows and macos; 7) Individual subprogram can be selected from the upgrade package; 1
4 Chapter 2 Installing Software Requirements Processor: 2.5GHz i5 or above processor (32 bit or 64 bit) Memory: 4GB or above Graphics: Support DirectX 9 128M or above (open AERO effect) Hard disk space: Above 128G (primary partitions, NTFS format) Monitor: Resolution must be pixels or above (if the resolution is lower than , some functions will not be displayed normally) Operating system: Windows 7 (non-ghost version or compact version) Software version: V Installation (1) Double click the icon, and a dialog box will pop up. Select the target language, for example, select English, and click OK to confirm. (2) Click Next to install: 2
5 Chapter 2 Installing Software (3) Select Browse... to select the destination folder: Note: When installing the software to disk C (Windows 7 or above), user should get the rights in Roles Management. (4) Click Install : In the process, a dialog box will pop up: 3
6 Chapter 2 Installing Software If the user installs the XTOOL software for the first time, click Next : Then click Install", as shown in the figure below: 4
7 Chapter 2 Installing Software (5) Click Finish, as shown in the figure below: Then click Next to complete the installation. If user has installed the XTOOL software before, click Cancel, and the dialog box will pop up: Click Yes to cancel installation. 5
8 Chapter 2 Installing Software Click Finish to exit installation. Then the dialog box will pop up, click Cancel to exit the installation. Click Finish and run the XTOOL application: 6
9 Double click the icon, and enter the interface as follows: XTOOL software contains the functions - Connection, Version, Toolbox, Language, Help and New File. In the following parts, we will introduce them in detail. 3.1 Connection Click Connection, and the dialog box will pop up: Serial Comm, Net Comm and USB Comm can be selected. Click Confirm. 7
10 3.2 Version The version interface is shown as follows: This is for software upgrade. XTOOL supports VENES X1, VENES X1 PRO, VENUS X2, VENUS X3, VENUS X3LIVE, VENUS X7, VSP 628PRO, CP 3072PRO, M-ONE, T-ONE, MSP 216, MSP 225, MSP 226, C1, C4 and C480. The operations are basically the same. The followings are the upgrade operations for VENUS X1PRO and VSP 628PRO. VENUS X1PRO Software Upgrade 1. Connect the device to PC Method 1: Connect the USB port of the PC to the USB port in the CONT area (Figure 3) of the VENUS X1PRO back panel with a USB cable (A to B) (Figure 1). Figure 1 USB Cable (A to B) Method 2: Connect the USB port of the PC to the RS232 port in the CONT area (Figure 3) of the VENUS X1PRO back panel with a USB to RS232-RJ11 cable (Figure 2). 8
11 Figure 2 USB to RS232 Cable Figure 3 CONT Area Note: USB connection is only applicable to VSP 628PRO, T-ONE and MSP Boot the device Input or output is not needed during the upgrade. 3. Open XTOOL Open XTOOL software. Click Language to switch the language. 4. Communication settings Serial Comm and Net Comm can be used to connect X1 PRO to PC. 4.1 Serial Comm 9
12 Click Connection, select Serial Comm in the dialog box. Select the corresponding serial number, and set Baud Rate as , click Confirm. If the device is connected, the circle indicating connection status at the bottom left corner turns green. If the connection fails, the circle remains red. Device type and SN are shown at the bottom right corner. 4.2 Net Comm (1) Use a LAN cable to connect X1 PRO to PC. (2) Check the IP address of X1 PRO from the menu: System Ethernet IP Address. 10
13 (3) Set the IP of the Connection Settings dialog box as the same with that of X1 PRO. Click Confirm to connect. 5. Select the *bin file in the upgrade package Click "Choose File" to select the bin file in the "Firmware Package" folder of the upgrade package. 6. Select the upgrade program (1) Click All, XTOOL will compare the version number and the subroutine version number of the package automatically. Only the items with different version number will be chosen for upgrade. 11
14 (2) Click "Upgrade", and a dialog box reading "Do you want to upgrade the firmware?" will pop up. Click "Confirm" to upgrade. (3) Check the upgrade progress by scroll bar. User can press the "Stop" button to stop the upgrade. (4) After the upgrade is completed, the New Version Upgraded! dialog box will pop up. At the 12
15 same time, the device will display UPGRADE SUCCESS! PLEASE RESTART! (5) Click Confirm, and reboot the device. VSP 628PRO Software Upgrade 1. Connect the device to the computer Connect the USB port of the computer to the USB port in the CONT area on the rear panel (Figure 2) with a USB cable (A to B) (Figure 1). Figure 1 USB Cable (A to B) Figure 2 CONT Area 2. Boot the device Input or output is not needed during the upgrade. 3. Open XTOOL Double click the XTOOL icon, and get into the main interface. Click Language to switch the language between Chinese and English. 13
16 4. Set the Comm Click Connection and choose USB Comm in the dialog box of Connection Settings. Remarks: Only USB comm can be used for VSP 628PRO connection. If the device is connected, the circle indicating connection status at the bottom left corner turns green. If the connection fails, the circle remains red. Device type and SN are shown at the bottom right corner. 14
17 5. Select package For upgrading VSP 628PRO, the packages can be divided as below: (1) If the software version of the control panel is lower than V2.88, upgrade the MCU package (VSP628PRO_MCU_V2.XX.bin) first, and then upgrade the Package [VSP628PRO_Packge_V2.XX.bin (the version is V2.88 or above)]. (2) If the software version of the control panel is V2.88 or above, upgrade the Package [VSP628PRO_Packge_V2.XX.bin (the version higher than V2.88)] Push the MENU button, choose Tech Support with the rotary knob, and enter Version No. to check the version No. of VSP 628PRO. Note: XX refers to the version No. of software. 5.1 Upgrade the MCU package (1) Click Choose File, and choose VSP 628PRO_MCU_V2.XX.bin in the upgrade software document. (2) Click ALL, XTOOL will automatically compare the version number of the local program with that of the subprogram in the package. If the version numbers are the same, ignore the option. If 15
18 the version numbers are different, the it indicates that the subprogram needs upgrade. Refer to the picture below: (3) After the program upgrade is finished, the reminder reading New Version Upgraded! will pop up. Meanwhile, red marquee will appear on the front panel buttons of the device. Click Confirm, and reboot the device. The upgrade of MCU program is finished. 5.2 Upgrade the Package (1) Click Choose File, and choose VSP 628PRO_Package_V2.XX.bin in the upgrade software document. 16
19 (2) Click ALL, XTOOL will automatically compare the version number of the local program with that of the subprogram in the package. If the version numbers are the same, ignore the option. If the version numbers are different, it indicates that the subprogram needs upgrade, as shown in the picture below. Besides, subprogram can be checked by scrolling mouse. (3) Click Upgrade, choose Confirm to upgrade when the dialog box reading Do you want to upgrade the firmware? pops up. The single subprogram and the whole upgrade process can be checked with scroll bar. If the upgrade needs to be suspended, press stop button to suspend it. (4) After the upgrade is finished, a dialog box indicating New Version Upgraded! will pop up. Meanwhile, the LCD screen on the front panel will also indicate the successful upgrade. 17
20 (5) Reboot the device and reset the device to the factory default settings. Make sure the program load is finished. 3.3 Toolbox Click Toolbox : It includes Custom OSD, Custom Mask, Custom Logo and Custom Still. 18
21 Custom OSD Select Custom OSD in Toolbox : OSD ON/OFF: Enable or disable the OSD function. Set the position and size: Adjust the position and size of OSD by setting the value of X, Y, width and height. Set the font: Set the font, font type, font color, strikeout or underline. Font transparency: Enable or disable the font transparency function. Background transparency: Enable or disable the background transparency function. Background color: Set the background color. Text entry: Type the text content that user wants to display, and set the size and position. Import text: Import the subtitle text saved before. Save text: Save the subtitle text for future use. Scrolling Speed: Set the scrolling peed, the adjustment range is between 1~16. Scrolling direction: Select Scroll Left or Scroll Right. After setting, choose Save To Device or Save To Computer, and click Apply. Save to Computer: 1. The file should be named as in order. Disruption of order is not permitted. 2. The file should be saved in the folder called #####\OSD. create a folder if no such folder is found. 3. After completion, insert the U Disk into the USB port at the Comm area. Import the file with the guidance of menu. 19
22 4. The format of U Disk must be FAT32. ##### varies by different devices. For example, if the device is VENUS X3LIVE, it should be named as X3LIVE ; If the device is CP 3072PRO, it should be 3072PRO. Make sure that the device is connected before operating Save To Device, Clear OSD and Apply. Custom Mask Select Create a Mask in Toolbox : File: Click File (*BMP) to choose an image. Background Color: Click Background Color and select the color. Create a Mask: Click Create a Mask, and save the mask to the USB disk. Note: 1. The picture format must be 24-bit BMP, and the size should not be larger than the output resolution. 2. The picture background should be solid-colored. It s white by default. 3. There should be only one mask on each picture. It s advisable to put the mask at the top left corner for position adjustment. 4. The file should be named as in order. Disruption of order is not permitted. 5. The file should be saved in the folder called #####\EFFECT. Create a folder if no such folder is found. 6. After completion, insert the U Disk into the USB port at the Comm area. Import the file with 20
23 the guidance of menu. 7. The format of U Disk must be FAT32. ##### varies by different devices. For example, if the device is VENUS X3LIVE, it should be named as X3LIVE ; If the device is CP 3072PRO, it should be 3072PRO. Custom Logo Select Custom Logo in Toolbox, get to the menu as follows: File: Click File (*BMP) to choose an image. Background Color: Click Background Color and select the color. Create a Logo: Click Create a Logo, and save the logo to the USB disk. Note: 1. The picture format must be 24-bit BMP, and the size should not be larger than The picture background should be solid-colored. It s white by default. 3. The file should be named as 1-50 in order. Disruption of order is not permitted. 4. The file should be saved in the folder called #####\LOGO. Create a folder if no such folder is found. 5. After completion, insert the U Disk into the USB port at the Comm area. Import the file with the guidance of menu. 6. The format of U Disk must be FAT32. ##### varies by different devices. For example, if the device is VENUS X3LIVE, it should be named as X3LIVE ; If the device is CP 3072PRO, it should be 3072PRO. 21
24 Custom Still Select Custom Still in Toolbox : File: Click File (*BMP) to choose an image. Background Color: Click Background Color and select the color. Create a Still: Click Create a STILL, and save the STILL to the USB disk. Note: 1. The picture format must be 24-bit BMP, and the size should not be larger than The picture background should be solid-colored. It s white by default. 3. The file should be named as 1-50 in order. Disruption of order is not permitted. 7. The file should be saved in the folder called #####\STILL. Create a folder if no such folder is found. 8. After completion, insert the U Disk into the USB port at the Comm area. Import the file with the guidance of menu. 9. The format of U Disk must be FAT32. ##### varies by different devices. For example, if the device is VENUS X3LIVE, it should be named as X3LIVE ; If the device is CP 3072PRO, it should be 3072PRO. 3.4 Language Click Language to switch language between Chinese and English. 22
25 3.5 Help Click Help : Software profile, including software name, version, supported comm and upgrade file requirement. 3.6 New File When there is new version for the device or software, a reminder reading New version is available. Do you want to upgrade? will pop up. Click Confirm to upgrade. After upgrade, the dialog box indicating Loaded! will pop up. Click Confirm. Then, the bin New File icon flashes. Click the icon, and the dialog box will pop up: It indicates that the bin file has been saved to the path automatically. Close the box, and the icon will not flash. 23
26 Chapter 4 Contact Us 24
27 Chapter 5 Revision History The table below lists the changes to the XTOOL User Manual. Format Time ECO# Description Principal V # Release Vira V # 1. Improve menu description; 2. Add bin New File Monica 25
CONTENTS. Xiamen RGBlink Science & Technology Co., Ltd. Ph: / 45
D6 Quick Start Internal 4:4:4 processing HDR compliance HDMI 2.0 / DP 1.2/ HDMI 1.4/ Dual Link DVI inputs compatible 12G/6G/3G/HD/SD SDI inputs compatible HDMI 2.0 output 12G/6G/3G/HD/SD SDI outputs EDID
More informationVENUS X3 Quick Start
VIEWSIZE THE WORLD VENUS X3 Quick Start Scalable videowall processing for large videowall with up to 8 displays or more Card frame videowall processing system available with 6 slots Integrates easily into
More informationGV-IP Decoder Box Plus User s Manual
GV-IP Decoder Box Plus User s Manual Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. DBPV10-UM-A 2015 GeoVision, Inc.
More informationUser Manual PDUTracker
User Manual PDUTracker Management Software for PDU Table of Contents 1. Overview... 1 1.1. Introduction... 1 1.2. Features... 1 2. Install and Uninstall... 1 2.1. System Requirement... 1 2.2. Software
More informationRS-1260 Digital Signage Player
RS-1260 Digital Signage Player User Manual V1.3 Legal Notice and Disclaimer Thank you for choosing RapidSignage products. This user manual provides a description of the Player relevant guidelines for key
More informationVX6s XI'AN NOVASTAR TECH CO., LTD. User Manual. All-in-One Video Controller. Document Version:
VX6s All-in-One Video Controller Document Version: Document Number: V1.0.0 NS160100270 Copyright 2018 Xi an NovaStar Tech Co., Ltd. All Rights Reserved. No part of this document may be copied, reproduced,
More informationGO! Finder V1.4. User Manual
GO! Finder V1.4 User Manual 1 Tables of Contents GO! Finder Introduction-------------------------------------------------------------------------------------1 System Requirements ---------------------------------------------------------------------------------------2
More informationPleiades - NDAS. User Manual. External Storage Enclosure for 3.5 IDE Hard Drives. v1.2
Pleiades - NDAS External Storage Enclosure for 3.5 IDE Hard Drives User Manual v1.2 EN Table of Contents CHAPTER 1 - INTRODUCTION - 1 - CHAPTER 4 - NDAS SETUP - 8 - ICON KEY - 1 - DRIVER INSTALLATION ON
More informationM9 - NDAS. User Manual. External Storage Enclosure for 3.5 IDE Hard Drives. (English) v1.4
M9 - NDAS External Storage Enclosure for 3.5 IDE Hard Drives User Manual (English) v1.4 EN Table of Contents CHAPTER 1 - INTRODUCTION - 1 - CHAPTER 4 - NDAS SETUP - 7 - ICON KEY - 1 - DRIVER INSTALLATION
More informationHow to update OS image from V1421 to V1501 by Exe file
Author Sean Hsu Version 1.0.0 Date 2010/4/20 Page 1/13 How to update OS image from V1421 to V1501 by Exe file Applies to: Platform OS version WinPAC/ViewPAC utility version WP-8x3x N/A N/A WP-8x4x All
More informationInstalling the Linksys app on your Android device via the Google Play Store and Google Play Website
User Guide Installing the Linksys app on your Android device via the Google Play Store and Google Play Website The Linksys app is a free mobile application that allows you to securely access your home
More informationVSM Manager. The VSM Manager is a Windows GUI that can be installed to serially control Genesis Matrixes with a firmware of version 2.5 or later.
VSM Manager Table of Contents Overview...1 Getting Started...1 Toolbar... 2 Serial Connection... 2 Refresh... 3 Help... 3 Tab Pages... 4 General... 4 Control...5 Schedule... 6 Command... 6 Communications...
More informationStat-VU Version 3.2 User s Guide
Stat-VU Version 3.2 User s Guide Part. No. 40310-03 540 North Commercial Street Manchester, NH 03101-1146 Tel. 603-645-1616 Support 603-606-5278 Fax 603-645-1424 Web www.ip-acd.com REVISION HISTORY 06/13/97
More informationEEG DE361 HD BAS Decoder Product Manual
EEG DE361 HD BAS Decoder Product Manual All rights reserved. [This page left intentionally blank] eeg Table Of Contents Introduction 2 Product Description... 2 Installation 3 Front Panel... 3 Rear Panel...
More informationTouch Screen Digital Signage (Network) User Manual
Touch Screen Digital Signage (Network) User Manual Manual Version: AOEF-DS (8350) Contents: 1. Installing Digital Signage App... 2 2. Getting Your Screen Online... 7 3. Menus... 11 3.1 Home Screen... 11
More informationAthlon4 Firmware Update Procedure by USB Memory (FIRMWARE1/FIRMWARE2/FIRMWARE3/FIRMWARE4) Rev.3.0
Athlon4 Firmware Update Procedure by USB Memory (FIRMWARE1/FIRMWARE2/FIRMWARE3/FIRMWARE4) Rev.3.0 Read This Manual Before Attempting Firmware Update This manual describes the procedure for updating firmware
More informationMaking a Bootable Linux USB Flash Drive with the Universal USB Installer.
Making a Bootable Linux USB Flash Drive with the Universal USB Installer. Insert the target USB flash drive into the USB port before starting the installer program. This is the start up screen for the
More informationOperating Instructions. Windows. Video Wall Adjustment & Calibration Software. Video Wall Manager Ver. 1.8
Operating Instructions Video Wall Adjustment & Calibration Software Windows Video Wall Manager Ver. 1.8 Thank you for purchasing this Panasonic product. Before using this software, please read the instructions
More informationI. Introduction of Main Interface. Instructions on XPrinter V3.0C Testing tools
I. Introduction of Main Interface Instructions on XPrinter V3.0C Testing tools 1 Communication port selection: Four options of printer communication interface: paralle port, serial port, USB port and Ethernet
More informationQ-Lab Software OPERATION MANUAL
Q-Lab Software OPERATION MANUAL Trilithic Company Profile Trilithic is a privately held manufacturer founded in 1986 as an engineering and assembly company that built and designed customer-directed products
More informationDiagnostic Utility. Quick Start Guide
Diagnostic Utility Quick Start Guide Contents 1. Getting started with Diagnostic Utility...1 1.1 Start the Diagnostic Utility...1 1.2 Select the PC interface connected with bar code printer...2 2. Configure
More informationYDEA C5 User Manual. Welcome to use products of YDEA! We are appreciated if our user. manual offers help and convenience to you when you are using or
YDEA C5 User Manual Version: 2-0-5 Statement Respectable Users: Welcome to use products of YDEA! We are appreciated if our user manual offers help and convenience to you when you are using or learning
More informationSystem Requirements Install HDML-Cloner Pro Helper Connect Register HDML-Cloner Pro Helper How to get the registration code of HDML-Cloner Pro Helper
9 9 12 17 System Requirements Install HDML-Cloner Pro Helper Connect Register HDML-Cloner Pro Helper How to get the registration code of HDML-Cloner Pro Helper 24 27 28 30 34 36 37 38 38 39 1 2 3 4 5 6
More informationInstallation. 5.) Click Next > when the following is displayed.
1 Installation 1.) Plug the Sign into an AC Outlet to turn on. 2.) Plug-in the USB Flash Drive (provided) to your Computer s USB Slot. (Wait a few second until it load) 3.) Open the USB Flash Drive & double
More informationKeyboard User s Manual
Keyboard User s Manual Version 1.0.0 1 Table of Contents 1 Features and Specifications... 7 1.1 Features... 7 1.2 Front Panel... 7 1.3 Rear Panel... 9 1.3.1 NKB1000 Series... 9 1.3.2 KB1000 Series... 9
More informationB-Works 2 User s Guide
B-Works 2 User s Guide UMBWORKS 011413V1 Table of Contents 1. Introduction... 2 2. System Requirements... 2 3. Install B-Works 2... 3 4. Connection to the Hardware... 7 5. Start to Use B-Works 2... 7 6.
More informationLab - Create a Partition in Windows 8
Lab - Create a Partition in Windows 8 Introduction In this lab, you will create a FAT32 formatted partition on a disk. You will convert the partition to NTFS. You will then identify the differences between
More information4-1. This chapter explains HMI settings.
4-1 4. Hardware Settings This chapter explains HMI settings. 4.1. Overview... 4-2 4.2. I/O Ports... 4-2 4.3. LED Indicators... 4-2 4.4. System Reset... 4-3 4.5. System Toolbar... 4-4 4.6. EasySystemSetting...
More information4-1. This chapter explains HMI settings.
4-1 4. Hardware Settings This chapter explains HMI settings. 4.1. Overview... 4-2 4.2. I/O Ports... 4-2 4.3. LED Indicators... 4-2 4.4. System Reset... 4-3 4.5. System Toolbar... 4-4 4.6. System Setting
More informationSCD Live SPEED TECH A/S
SPEED TECH A/S Nybrovej 97. DK2820 Gentofte. Phone: +45 45938545 Fax: +45 45938544 www.doorcontrol.dk - info@speed-tech.dk Contents: SCD Live 1 INTRODUCTION... 3 1.1 DESCRIPTION... 3 1.2 DISCLAIMER...
More informationPrint Server. User s Manual. Rev. 01 (April, 2004) Made In Taiwan
Print Server User s Manual Rev. 01 (April, 2004) Made In Taiwan TABLE OF CONTENTS ABOUT THIS GUIDE... 4 INTRODUCTION... 5 PACKAGE CONTENTS... 6 SYSTEM REQUIREMENTS... 6 GENERAL FEATURES... 7 PRODUCT VIEW...
More informationTable of Contents. Manual Overview
Table of Contents Manual Overview D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions
More informationMini Converter User Manual
Mini Converter User Manual MSP 207 VGA to AV RGBlink Science & Technology Co., Ltd. The pictures and data in the user manual are consult only, if there is fluctuation, according to the real object please!
More informationIndustrialPro Routers (SN/RAM Series) Wireless Modems
Wireless Modems Including SN/RAM-67xx LTE and RAM-9000 families Migration and Advanced Firmware Update Procedures Version 3.20/4.20 February 2015 CHANGE HISTORY Version Date Description 3.20 February 17,
More informationSetup Network File Sharing between Windows PC and A-ScanPlus
Microsoft Windows operating system (OS) allows the user to share a specific folder to other computers on the same local area network. Accutome A-Scan Plus utilizes this feature to transfer exams and printouts
More informationInstructions for Installing FlashUpdate and Downloading Updates for NPRT 2200 Noise Power Ratio Test Set
Instructions for Installing FlashUpdate and Downloading Updates for NPRT 2200 Noise Power Ratio Test Set Updates to the instrument firmware are available from the Applied Instruments website. Requirements
More informationHP Video Over Ethernet. User Guide
HP Video Over Ethernet User Guide 2016 HP Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth
More informationVikinX User Manual. THOR Basic Edition. network-electronics.com. Rev
r VikinX User Manual THOR Basic Edition network-electronics.com Rev. 3.5.6 Network Electronics ASA Thorøya P.O. Box 1020 Sandefjord, Norway Phone: +47 33 48 99 99 Fax: +47 33 48 99 98 E-mail: support@network-electronics.com
More informationT E C H N O L O G I E S ENT ESC. User Guide. 1:4 CF or CFAST Duplicator PRO (CFASTD4-2S / CFD4-2S)
T E C H N O L O G I E S ENT ESC CFAST CF User Guide 1:4 CF or CFAST Duplicator PRO (CFASTD4-2S / CFD4-2S) www.addonics.com v3.1.11 Technical Support If you need any assistance to get your unit functioning
More informationSetup and Configuration
Setup and Configuration OmniStream TM Solution Guide OmniStream Atlona Setup Guide Version Information Version Release Date Notes 1 02/19 Initial release 2 03/19 Audio added 3 03/19 USB added OmniStream
More informationUser s Manual of DVR ULTIMAX. Remote Client Software V wersja 2.40
User s Manual of DVR ULTIMAX Remote Client Software V 4.0.1 ULTIMAX-304 ULTIMAX-308 ULTIMAX-316 ULTIMAX-504 ULTIMAX-508 ULTIMAX-516 ULTIMAX-704 ULTIMAX-708 ULTIMAX-716 wersja 2.40 Index 1 Software Install,
More informationMedia Player Mdea User Manual
Media Player Mdea User Manual Version: V04 Date: 2015-07-31 CONTENTS 1 System Overview... 1 2 System Features... 1 3 Technical Specifications:... 2 4 System Solutions... 3 5 Software Application... 3 5.1
More informationModel No user manual PRO
Model No. 258011 user manual PRO Index Introduction Features Specification Button definition Operation Instruction Power ON/OFF LCD backlight Five main functions PinTest QuickTest Browse Delete Settings
More informationRC-SV Configuration Guide Revision 3
Kramer Electronics, Ltd. RC-SV Configuration Guide Revision 3 Software Version 2.1.2.32 Intended for Kramer Technical Personnel or external System Integrators. To check that you have the latest version,
More informationWISP Setup Guide for TP-Link TL-WR841N 300 Mbps Wireless N Router AARP Foundation Tax-Aide Colorado Technology Specialist
WISP Setup Guide for TP-Link TL-WR841N 300 Mbps Wireless N Router AARP Foundation Tax-Aide Colorado Technology Specialist Summary This document explains how to configure the TP-Link WR841N router to provide
More informationPowerVIEW HD 22/30 Version
Release Notes 9/17/15 PowerVIEW HD 22/30 Version 1.01.04 Released 9/17/15 Additions and Enhancements Improved IR Processing in Half-Recessed Ceiling Mount Improved 1080p/25 video quality. Fixed Issues
More informationOPERATION MANUAL. MV-410HS Layout Editor. Version higher. Command
OPERATION MANUAL MV-410HS Layout Editor Version 3.0 - higher Command Command Table of Contents 1. Setup... 1 1-1. Overview... 1 1-2. System Requirements... 1 1-3. Operation Flow... 1 1-4. Installing MV-410HS
More informationINSTALLING THE PS3 XBOX READY SOFTWARE:
INSTALLING THE PS3 XBOX READY SOFTWARE: 1. Insert the Installation CD to CD-ROM drive and execute Ready_Setup.exe NOTE: If it is the first time for the target USB disk using under this software, the software
More informationRC-SV Configuration Guide (Rev 4)
Kramer Electronics, Ltd. RC-SV Configuration Guide (Rev 4) Software Version 2.1.2.69 Intended for Kramer Technical Personnel or external System Integrators. To check that you have the latest version, go
More informationSNMP Web Management. User s Manual
SNMP Web Management User s Manual Suitable Product: SNMP Web Card SNMP Web Box Management Software for Uninterruptible Power Supply Systems Table of Contents 1. Overview... 1 1.1 Introduction... 1 1.2
More informationOperating Instructions. Windows. Logo Transfer Software 2.0. Thank you for purchasing this Panasonic product.
Operating Instructions Logo Transfer Software 2.0 Windows Thank you for purchasing this Panasonic product. Before using this software, please read the instructions carefully. TQBH9059-8 Table of Contents
More informationApplied ICT Skills MS Windows
Applied ICT Skills MS Windows Lesson 1 - How to install an operating system into computer? Windows 7 is perhaps the best Microsoft operating system and is very easy to install compared to other windows.
More informationVersion: 01P02B. U3 Map Maker Operational Guide
Contents 1. Map Maker Software Overview... 4 1.1 Features... 4 1.2 Remarks... 4 1.3 Supported Devices... 4 2. Installing U3 Map Maker... 5 2.1 System Requirements... 5 2.2 Map Maker Installation... 5 3.
More informationInstrument Software Update Instructions. X-Series Multi-touch instruments
Purpose Instrument Software Update Instructions X-Series Multi-touch instruments The purpose of this document is to outline the instrument software update procedure for the touchscreen or B model instrument
More informationChapter 1: Introduction. Chapter 2: Getting Started
Chapter 1: Introduction Media Player 200 is a Digital Media Player that includes a connector for a USB storage device and card reader. The Media Player 200 connects to your home entertainment center allowing
More informationInstalling the IBM ServeRAID Cluster Solution
Installing the IBM ServeRAID Cluster Solution For IBM Netfinity ServeRAID-4x Ultra160 SCSI Controllers Copyright IBM Corp. 2000 1 2 IBM Netfinity Installing the IBM ServeRAID Cluster Solution Chapter 1.
More informationVision Express Engraver S5 Installation Guide Vision Engraving & Routing Systems
Vision Express Engraver S5 Installation Guide Part number 12-1084-01 Revised: 11/5/2018 Vision Express Engraver S5 Installation Guide All rights reserved. No parts of this work may be reproduced in any
More informationVision Express Vision VE810 Installation Guide Vision Engraving & Routing Systems
Vision Express Vision VE810 Installation Guide Vision Express - Vision VE810 Installation Guide All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic,
More informationC (1) Remote Controller. Setup software RM-IP Setup Tool guide Software Version Sony Corporation
C-499-100-12 (1) Remote Controller Setup software RM-IP Setup Tool guide Software Version 1.1 2017 Sony Corporation Table of Contents Introduction... 3 Using This Manual...3 Downloading and Starting the
More informationField PC 2 Windows OS Update Guide
Field PC 2 Windows OS Update Guide All efforts have been made to ensure the accuracy and completeness of the information contained in this document. RST Instruments Ltd reserves the right to change the
More informationPhoenix 1212 Engraver S5 Installation Guide Vision Engraving & Routing Systems
Phoenix 1212 Engraver S5 Installation Guide Part number 12-1084-01 Revised: 12/10/2018 Phoenix 1212 Engraver S5 Installation Guide All rights reserved. No parts of this work may be reproduced in any form
More informationVision VE810 Engraver S5 Installation Guide Vision Engraving & Routing Systems
Vision VE810 Engraver S5 Installation Guide Part number 12-1085-01 Revised: 11/5/2018 Vision VE810 Engraver S5 Installation Guide All rights reserved. No parts of this work may be reproduced in any form
More informationAbout Manual Pairing on Coaxial-LAN Converter
About Manual Pairing on Coaxial-LAN Converter April, 2016 Panasonic System Networks Co, Ltd Security System Business Division This document describes about the function of Manual Pairing which has been
More informationLS-300 Media Station
LS-300 Media Station User Manual English AREC Inc. All Rights Reserved 2017. l All information contained in this document is Proprietary Table of Contents Introduction Specifications Package Contents Product
More informationMELBOURNE LED LEDEDITOR 2016 SOFTWARE MANUAL
MELBOURNE LED LEDEDITOR 2016 SOFTWARE MANUAL Chapter 1: Introduction 1.1 Function Feature The LED Editor Version 2 has been upgraded to offer wider range of control and satisfy requirement of multi functions
More informationContents LOCAL MANAGEMENT LOGIN INTERFACE RECORD SEARCH: LOG SEARCH SYSTEM STATUS BASIC SETUP.
User Manual For MD AHD MDVR Copyright 2013-2016, Howen Technology Co., Ltd All Rights Reserved 1-59 Contents 1. 2. LOCAL MANAGEMENT... 3 2.1. LOGIN INTERFACE... 3 2.2. RECORD SEARCH:...6 2.3. LOG SEARCH...
More informationSQP110 Series. User s Manual V1.0.3 SQP110V103-B
SQP110 Series User s Manual V1.0.3 SQP110V103-B 2012 GeoVision, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of GeoVision.
More informationLionstracs Groove X-R
Lionstracs Groove X-R Groove OS version 5.3 Installation & Upgrade Guide 31 October 2011 English Language documentation prepared by Corcyra Global in consultation with Lionstracs Table of Contents Warning
More informationIT Essentials v6.0 Windows 10 Software Labs
IT Essentials v6.0 Windows 10 Software Labs 5.2.1.7 Install Windows 10... 1 5.2.1.10 Check for Updates in Windows 10... 10 5.2.4.7 Create a Partition in Windows 10... 16 6.1.1.5 Task Manager in Windows
More informationInstrument Software Update Instructions
Purpose Instrument Software Update Instructions Keysight X-Series Signal Analyzers, Non-Touch (N9000A, N9010A, N9020A, N9030A) With either WES7 or Windows 10 operating systems The purpose of this document
More informationIP Device Search and Configuration Tool Operation Manual
IP Device Search and Configuration Tool Operation Manual Note Copyright Statement This manual may not be reproduced in any form or by any means used to create any derivative such as translation, transformation,
More informationOperating Instructions WhiteBoard Software for Mac 1.4
Operating Instructions WhiteBoard Software for Mac 1.4 Please read these instructions carefully before using this product, and save this manual for future use. Panasonic Corporation 2018 Contents INTRODUCTION...
More informationCENTAUR S REAL-TIME GRAPHIC INTERFACE V4.0 OPERATOR S MANUAL
CENTAUR S REAL-TIME GRAPHIC INTERFACE V4.0 OPERATOR S MANUAL TABLE OF CONTENTS Installation... 6 Introduction to Centaur s real-time Graphic Interface... 6 Computer Requirements... 7 Operating System
More informationV2.0. HD60 Video Recorder Record Full HD Videos & Playback instantly
V2.0 HD60 Video Recorder Record Full HD Videos & Playback instantly Important Safety Instruction Before using HD60 Video Recorder, please ensure that you read and understand the safety precautions below:
More informationDXP D0808 Quick Start
VIEWSIZE THE WORLD DXP D0808 Quick Start Support any in any out Support independent output switching Support hot backup Support infrared remote control Can read and store up to 24/36 user scenarios Automatically
More informationTo complete this project, you will need the following folder:
= CHAPTER 1 Windows 7 More Skills 12 Use Libraries to Organize Files A library is a collection of files and folders stored in different locations on your computer that can be viewed as a single folder.
More informationUPGRADE INSTRUCTIONS
Version 2.48 or 2.49 & Version 3.48 or 3.49 UPGRADE INSTRUCTIONS System Upgrade Requirements NOTE: Non I-Button: V-Sperm Gold version 3.49 must be installed with SQA-V Gold version 2.49. I-Button: V-Sperm
More informationUT163/UT165/UT190 USB Flash Disk Utility
UT163/UT165/UT190 USB Flash Disk Utility User s Manual Rev. 3.2.4.0 JUNE. 12, 2008 http://www.afatech.com All rights strictly reserved. Any portion of this paper shall not be reproduced, copied, or translated
More informationInfinova SS200T3R Embedded VMS Box
Infinova SS200T3R Embedded VMS Box WARNING Embedded VMS advanced maintenance is special activity and it is highly recommended that only trained engineers operate the maintenance procedures. Incorrect configuration
More informationStarter Kit Manual. Table of Contents
Starter Kit Manual Table of Contents Chapter 1 Introduction of UT Series Starter Kits 1.1 General Information about UT Series Starter Kits... 1-2 1.1.1 Components of UT Series Starter Kits... 1-2 1.2 System
More informationWELDSEQ Plus. Operation / Installation Manual. Weld Sequence PLC Terminal Program. Computer Weld Technology, Inc.
Computer Weld Technology, Inc. 10702 Old Bammel N Houston Rd. Houston, TX 77086 Phone: (713) 462-2118 Fax: (713) 462-2503 Email: cwt@cweldtech.com WELDSEQ Plus Weld Sequence PLC Terminal Program Operation
More informationGUI MANAGER USER GUIDE
GUI MANAGER USER GUIDE Rev. 2.0.0 December, 2012 www.tvielectronics.com 2211 Rayford Rd., Ste. 111-332 Spring, TX 77386 281-408-4051 281-408-4052 CONTENTS 1. DOCUMENT CONVENTIONS... 1 2. INSTALLATION INSTRUCTIONS...
More information10/100Mbps 2Port USB2.0 MFP Server
10/100Mbps 2Port USB2.0 MFP Server Mini-MFP Quick Installation Guide English Ver.1.0 Quick Installation Guide CONTENTS STEP 1 / Mbps Port USB MFP Server Introduction Package Contents OS Requirements Physical
More informationWA1547 WebSphere Portal v6 Programming. Classroom Setup Guide. Web Age Solutions Inc. Copyright Web Age Solutions Inc.
WA1547 WebSphere Portal v6 Programming Classroom Setup Guide Web Age Solutions Inc. 1 Table of Contents Classroom Requirements...3 Part 1 - Minimum Hardware Requirements...3 Part 2 - Minimum Software Requirements...3
More informationThe Fundamentals. Document Basics
3 The Fundamentals Opening a Program... 3 Similarities in All Programs... 3 It's On Now What?...4 Making things easier to see.. 4 Adjusting Text Size.....4 My Computer. 4 Control Panel... 5 Accessibility
More informationShenzhen Rikomagic Tech Corp.,Ltd
Shenzhen Rikomagic Tech Corp.,Ltd Table of Contents Declaration... 2 1. MK902 hardware introduction... 3 1.1 Connector... 3 1.2 Device connection Instruction...3 2. Boot state...4 3 Main Screen Introduction...
More informationSMART (Samsung Multiple Automatic Re-flash Tool) User Guide - For Managers
SMART (Samsung Multiple Automatic Re-flash Tool) User Guide - For Managers Copyright 2012 Samsung Electronics Co. Ltd. All rights reserved. Ver. 5.0 / SMART 3.12.0211 05.03.2012 1. What is SMART? With
More informationStandard Plus Player. User Guide. i-tech Company LLC TOLL FREE: (888) WEB:
Standard Plus Player User Guide i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com 1. INTRODUCTION OF THE Standard Plus PLAYER... 3 2. MAIN MENU... 4 2.1 START
More informationPixel Software/Firmware Update Instructions
1 Loading Software on to USB Flash Drive 1. The latest Pixel software can be downloaded from the Elevator Controls website (elevatorcontrols.com/downloads/download) a user name and password is required.
More informationUser can upgrade the firmware directly using the Web or Console.
17. Firmware Upgrade User can upgrade the firmware directly using the Web or Console. Firmware name (current) and applied model: V3K31257_en.all:Vigor 3300B+ 2.5.7 English version. V3K31257_cn.all:Vigor
More informationT E C H N O L O G I E S. User Guide. 1:1 HDD Duplicator PRO (HDUSI325)
T E C H N O L O G I E S Duplicator Panel Power Switch Source Drive Bay Target Drive Bay User Guide 1:1 HDD Duplicator PRO (HDUSI325) www.addonics.com v3.1.11 Technical Support If you need any assistance
More informationSection 1 M SiteSentinel Integra and isite Software Upgrade Procedure
Page 1 of 18 Section 1 M00-20-4438 - SiteSentinel Integra and isite Software Upgrade Procedure 1.1 Integra Upgrade Procedure This procedure shows the necessary steps to upgrade the Integra console software.
More informationSTOP! Read these instructions before connecting the PR3 to your Computer
Windows 10 Installation Instructions for the PR3 NOTE: If Windows 10 installed the drivers for the PR3, these instructions are not needed. These instructions are only to be used if Windows 10 did not automatically
More informationitrax PC Replacement Quick Start Guide P/N Pre-Software Installation
Quick Start Guide P/N 60789-0 Use this procedure to upload the current software onto a new itrax PC. To access the newest software, contact ICS Technical Support at ics.tech.support@nordson.com. Follow
More informationSetup Guide for Hard-Wire Ethernet Connected TP-Link TL-WR841N 300 Mbps Wireless N Router AARP Foundation Tax-Aide Colorado Technology Specialist
Setup Guide for Hard-Wire Ethernet Connected TP-Link TL-WR841N 300 Mbps Wireless N Router AARP Foundation Tax-Aide Colorado Technology Specialist Summary This document explains how to configure the TP-Link
More informationProduct Family: Networking Hardware Number: AN-NH-012
APPLICATION NOTE THIS INFORMATION PROVIDED BY AUTOMATIONDIRECT.COM TECHNICAL SUPPORT These documents are provided by our technical support department to assist others. We do not guarantee that the data
More informationOperating Instructions. Windows. Logo Transfer Software 2.0 M1010KT1011 -FJ TQBH9021-1(E)
Operating Instructions Logo Transfer Software 2.0 Windows M1010KT1011 -FJ TQBH9021-1(E) Table of Contents Read This First....................... 2 Restrictions...3 The number of LOGOs, the maximum pixel
More informationKlick & Show Firmware-Update (GB)
Klick & Show Firmware-Update (GB) An update of the firmware can be useful to take the advantage of new features of Klick & Show or to fix known issues and bugs. There are three different areas for updating:
More informationNetwork Camera Firmware Upgrade Quick Guide
Network Camera Firmware Upgrade Quick Guide 09-2018 / v1.0 1 CONTENTS I Introduction... 3 II How to Upgrade Firmware for Network Camera... 4 III Download App... 11 2 I Introduction To strengthen the security
More informationUniversal CCU CAT-5 Release Notes
BLURB Release Notes Universal CCU CAT-5 Release Notes Release Version: V 1.01.16 Release Date: 10/30/2014 Component Version Hardware -327A PIC 1.01.16 FPGA update not needed in this release New Features
More information