Agilent EZChrom SI. Startup Guide

Transcription

1 Agilent EZChrom SI Startup Guide

2 Notices Copyright Scientific Software, Inc 2003 Agilent Technologies, Inc No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies, Inc. as governed by United States and inter-national copyright laws. Manual part number G Edition October, 2006 Printed in USA Agilent Technologies, Inc Owens Dr. Pleasanton, CA Warranty The material contained in this document is provided as is, and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applicable law, Agilent disclaims all warranties, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied warranties of merchant-ability and fitness for a particular purpose. Agilent shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein. Should Agilent and the user have a separate written agreement with warranty terms covering the material in this document that conflict with these terms, the warranty terms in the separate agreement shall control. Technology Licenses The hardware and/or software described in this document are furnished under a license and may be used or copied only in accordance with such license. Restricted Rights Legend If software is for use in the performance of a U.S. Government prime contract or subcontract, Software is delivered and licensed as "Commercial computer software" as defined in DFAR (June 1995), or as a "commercial item" as defined in FAR 2.101(a) or as "Restricted computer software" as defined in FAR (June 1987) or any equivalent agency regulation or contract clause. Use, duplication or disclosure of Software is subject to Agilent Technologies standard commercial license terms, and non-dod Departments and Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in FAR (c)(1-2) (June 1987). U.S. Government users will receive no greater than Limited Rights as defined in FAR (June 1987) or DFAR (b)(2) (November 1995), as applicable in any technical data.

3 Contents 1 Using This Guide... 4 Introduction... 4 Who Should Read This Guide?... 4 Documentation Conventions Introduction... 5 Limitations and differences Installation... 5 Configuring EZChrom SI... 6 Starting EZChrom SI... 9 EZChrom SI Guide iii

4 1 Using This Guide Introduction This guide describes how to install and configure the Agilent EZChrom SI data system. Who Should Read This Guide? This guide is intended for managers and users who will be installing and configuring the Agilent EZChrom SI data system. Documentation Conventions The following conventions are used in this guide. Convention Bold Italic Monospace ALL CAPITALS Description Database names, table names, column names, menus, commands, dialog box options, and text that must be typed exactly as shown. Placeholders for information you must provide. For example, if you are instructed to type ServerName, then you must type the actual name of the server instead of the italicized term. Programming code samples and display text. The keys you press on the keyboard. If combined with a plus sign (+), press and hold the first key while you press the remaining key(s). For example, press SHIFT+TAB. 4 EZChrom SI Guide

5 2 Introduction EZChrom SI is a single-instrument version of the Agilent EZChrom Elite Data System. It has essentially the same functionality as EZChrom Elite (see Limitations below) for control and data acquisition, analysis, and processing, but is limited to a single instrument. Limitations and differences Please note the following limitations and differences between EZChrom SI and the EZChrom Elite Data System. Enterprise-oriented functions such as user/project administration, electronic signature, audit trails, and notification, are not available in this version. Advanced Reporting functions and the ability to save custom report templates are not available. Sequence summary reports are created using the standard Custom Report Editor rather than Advanced Reports. With the exception of this EZChrom SI User s Guide, all documentation you receive will be for the full EZChrom Elite Data System. You should refer to the appropriate sections of that documentation for descriptions of instrument control and software use. Before you begin using EZChrom SI, you must install the software and configure the hardware (acquisition hardware and instruments) you will be using, as described in the following sections. 3 Installation The following steps should be followed when installing and configuring your EZChrom SI system. EZChrom SI Guide 5

6 a. Install all hardware (A/D board, terminal panel, and instrument connections). Refer to the Hardware Installation section located in the main EZChrom Elite Installation Guide for details. b. If running Windows 2000, log into the computer as a local administrator so you have full rights to install application software. c. Install EZChrom SI software following the instructions presented. See EZChrom Elite documentation supplied for complete details. d. Install the software license key. Refer to the Software License Installation section located in the EZChrom Elite Installation Guide. e. Configure A/D hardware and instrument (detectors, external events). Refer to the Configuration chapter of the System Admin Guide, or for configuration of digital control for specific instruments (such as Agilent 1100 LC), see the control option documentation for that instrument. Configuring EZChrom SI Once you have installed the hardware and software, you need to configure the system before you can use it. To run the configuration program, run the program from the Windows Start button as follows: From the Start menu, select All Programs. Point to the Chromatography menu, and then select EZChrom SI Config, The following dialog box will appear. 6 EZChrom SI Guide

7 Interface Configuration Click Interface Configuration to select and configure the data acquisition interface you will be using. If you are using digital acquisition and control of certain instruments, you may not be using an analog data acquisition interface. In this case, refer to the documentation provided for the specific digital instrument you will be using. Instrument Configuration Click Instrument Configuration to start the instrument configuration dialog. Select the instrument you will be using from the drop-down list, then proceed to configure the instrument according to the documentation for that instrument and the online help provided. EZChrom SI Guide 7

8 Extract Configuration from Data File Click Extract Configuration from Data File to configure from an existing data file that was acquired using the exact configuration you wish to use. 8 EZChrom SI Guide

9 Starting EZChrom SI Once you have properly installed and configured the hardware and software, run the EZChrom SI instrument program using the Windows Start button, as follows: Start/Programs/Chromatography/EZChrom SI From this window you perform all aspects of instrument setup, method development, sequence development, calibration, data acquisition, processing, and reporting. Refer to the User Guide and Reference documents provided with your system for details on using the system. EZChrom SI Guide 9

10

11

12