Programmable OLED Video Switch and Display

Transcription

1 DISTINCTIVE CHAACTEISTICS Organic LED technology ange of 65,56 colors in 6 bit mode, 56 colors in bit mode Full viewing angle of 0 Exceptional contrast and brightness: 50 times greater brightness than previous LCD products, four times more enhanced resolution High resolution provides sharp, clear images of very small characters Operated by commands and data supplied via SPI communications protocol Distinct, long travel of.5mm (same as KP0 Series) Dust tight construction Sophisticated housing based on black color Viewing area: 5.5mm x.6mm (horizontal x vertical) High reliability and long life of three million actuations minimum High resolution of 6GB x pixels Epoxy Sealed Straight PC Terminals Snap-in Standoff for Easy, Secure Mounting and Alignment Viewing area:.mm x.mm (horizontal x vertical) High resolution of 5GB x 6 pixels Crimped terminals ensure secure PC mounting and prevent dislodging during wave soldering APPLICATIONS The OLED SMATSWITCH TM Series complements multiple applications, including: Actual Sizes Broadcast equipment Education equipment Audio equipment Image equipment Vending machines POS Automation control equipment sales@greatecs.com

2 SMATSWITCH PAT NUMBE & DESCIPTION Part Number Switch Description OLED Pixel Format ISC5ANP SPST Momentary ON Gold Contacts Straight PC Terminals Color OLED Display Module 65,56 Colors 6GB x Pixels Horizontal x Vertical SMATSWITCH SPECFICATIONS Circuit Contact Position Electrical Capacity (esistive Load) Contact esistance Insulation esistance Dielectric Strength Mechanical Endurance Electrical Endurance Operating Force SPST normally open Leave actuator: OFF Push actuator: ON V DC 00 milliohms 0mV 0mA 00 megohms 00V DC 5V AC for minute minimum,000,000 operations minimum,000,000 operations minimum.0 ± 0.5 Newtons Total Travel.5mm (. ) SMATSWITCH OLED SPECFICATIONS Characteristics of Display Display Device Display Mode Viewing Area Pixel Format Pixel Size Interface Number of Colors Operating Temperature ange Storage Temperature ange Operating Life Time (Display) Absolute Maximum atings Items Symbols atings V DD 0.V to +.0V Drive V CC 0.V to +.0V Input Voltage V I 0.V to V D D +0.V Current Consumption (Temperature at 5 C, V DD =.V, V CC = 6.0V) Items Symbols Min Typical Max *Drive System Power Current *Logic/IF System Power Current **Drive System Power Current **Logic/IF System Power Current I CC 5.5mA.0mA I DD 0.6mA 0.mA I CC 0μA I DD 0μA * All pixels shall be turned on with the maximum level gray scale ** All pixels shall be turned off (while chip is operating) Color OLED display module Passive matrix 5.5mm x.6mm (horizontal x vertical) 6GB x pixels (horizontal x vertical) 0.mm x 0.0mm (horizontal x vertical) Serial (SPI) interface 65,56 Colors (6bit: 5bit/G 6bit/B 5bit) or 56 Colors (bit: bit/g bit/b bit) 0 C ~ +0 C ( F ~ +5 F) 0 C ~ +0 C ( F ~ +6 F) 5,000 hours (at 0% duty) ecommended Operating Conditions Items Symbols Minimum Typical Maximum V DD.V.V.5V Drive V CC 5.0V 6.0V.0V Input High Level Voltage V IH 0. x V DD Input Low Level Voltage V I L 0.V x V DD Optical Characteristics (Temperature at 5 C, Initial Value: x 0F) Items Min Typical Max Unit emarks Luminosity cd/m White (All pixels on) White Color ed Color Green Color Blue Color (x) (y) (x) (y) (x) (y) (x) (y) Contrast atio 00 sales@greatecs.com

3 SMATSWITCH BLOCK DIAGAM & PIN CONFIGUATIONS Color OLED Panel 6GB x S,SG,SB...S6, SG6,SB6 COM...COM Segment Driver Common Driver VDD VCC SEG/COM Driving Block OLED Driver with Controller ES 5 Gray Scale Decoder Oscillator SCK SS Graphic Display Data AM 6 x 6 x 6 Bit Display Timing Generator 6 GND 0 MCU Interface Command Decoder ISC5ANP SW SW Pin No. Symbol Name Function SW Terminal of Switch Normally open SW Terminal of Switch Normally open V DD Power Power source for logic circuit SS Slave Select Slave select for SPI. This line is active low. ES eset eset signal input. When pin is low, initialization of chip is executed Data/Command Data/Command Control. When pin is pulled low, data will be interpreted as Command; when pulled high, data will be interpreted as Data. SCK Serial Clock Clock line for SPI that synchronizes command and data Serial Data In Data input line for SPI V CC Power Power source for drive OLED GND Ground Connect to ground SMATSWITCH TYPICAL DIMENSIONS See Pixel Detail (.6).5 (0.5). (.).5 (5.5).60 (.). (.5). (0.).0 (.0).06 (.).0 (0.6) Typ.0 (0.) Typ.06 See Standoff Detail (.). Terminal numbers are not on the switch. (.0).0 Standoff Standoff (.6).00 (6.0).60 (.0).5 (.05). (.0) Typ.0.6 Standoff Standoff (0.) Typ (0.) Typ (.0) (0.0) Typ.00 (0.0) Typ.000 Pixel Detail Pixel Detail A Standoff Detail (0.) Typ.00 (0.0).000 Typ See Pixel Detail A (0.0).00 (0.).006 (0.0) Typ.006 (0.0) Typ.00 G B (0.).00 Standoff = (.).06 (0.).00 Dimension A A (.5).0 (.0) Dia Standoff = (.).0 Footprint (.0) Typ.0.6 x (0.5).0 Dia (.0) 0 (.05). (.0).0 (.0).5 x (0.).05 Dia (.6).00 (6.0).60 x (.) Dia.05 Landless sales@greatecs.com

4 SMATSWITCH PAT NUMBE & DESCIPTION Part Number Display Description OLED Pixel Format ISC0P Straight PC Terminals Color OLED Display Module 65,56 Colors 5GB x 6 Pixels Horizontal x Vertical SMATSWITCH LCD SPECFICATIONS Characteristics of Display Display Device Display Mode Viewing Area Pixel Format Pixel Size Interface Number of Colors Operating Temperature ange Storage Temperature ange Operating Life Time (Display) Color OLED display module Passive matrix.mm x.mm (horizontal x vertical) 5GB x 6 pixels (horizontal x vertical) 0.mm x 0.mm (horizontal x vertical) Serial (SPI) interface 65,56 Colors (6bit: B 5bit/G 6bit/ 5bit) or 56 Colors (bit: B bit/g bit/ bit) 0 C ~ +0 C ( F ~ +5 F) 0 C ~ +0 C ( F ~ +6 F) 5,000 hours (0% pixels ON) Absolute Maximum atings Items Symbols atings Absolute Maximum atings Items Symbols Minimum Typical Maximum V DD 0.V to +.0V V DD.V.V.5V Drive V CC 0.V to +.0V Input Voltage V I 0.V to V D D +0.V Current Consumption (Temperature at 5 C, V DD =.V, V CC = 6.0V) Items Symbols Min Typical Max *Drive System Power Current *Logic/IF System Power Current **Drive System Power Current **Logic/IF System Power Current I CC.5mA.5mA I DD 0.6mA 0.mA I CC 0μA I DD 0μA *All pixels shall be turned on with the maximum level gray scale **All pixels shall be turned off (while chip is operating) Drive V CC 5.0V 6.0V.0V Input High Level Voltage V I H 0. x V D D Input Low Level Voltage V I L 0.V x V D D Optical Characteristics (Temperature at 5 C, Initial Value: x 0F) Items Min Typical Max Unit emarks Luminosity cd/m White (All pixels on) White Color ed Color Green Color Blue Color (x) (y) (x) (y) (x) (y) (x) (y) Contrast atio 00 sales@greatecs.com

5 SMATSWITCH BLOCK DIAGAM & PIN CONFIGUATIONS Color OLED Panel 5GB x 6 S,SG,SB...S5, SG5,SB5 COM...COM6 Segment Driver Common Driver VDD VCC SEG/COM Driving Block OLED Driver with Controller ES Gray Scale Decoder Oscillator SCK 5 SS Graphic Display Data AM 6 x 6 x 6 Bit Display Timing Generator 6 MCU Interface Command Decoder ISC0P GND Pin No. Symbol Name Function V DD Power Power source for logic circuit SS Slave Select Slave select for SPI. This line is active low. ES eset eset signal input. When pin is low, initialization of chip is executed Data/Command Data/Command Control. When pin is pulled low, data will be interpreted as Command; when pulled high, data will be interpreted as Data. 5 SCK Serial Clock Clock line for SPI that synchronizes command and data 6 Serial Data In Data input line for SPI V CC Power Power source for drive OLED GND Ground Connect to ground SMATSWITCH TYPICAL DIMENSIONS See Pixel Detail (.).50 See Standoff Detail (0.).06 Typ Terminal numbers are not on the switch. (0.0). (0.65) Typ.06 (.).0 (.).6 (0.). (.).0 (.). (0.5).00 (0.).0 (.).0 Pixel Detail Pixel Detail A Footprint (0.).00 (.0). (6.).66 (.0) (.).5 (5.5).0 (.0) (.0) Typ (0.).0.06 Typ.6 (5.0).5 (5.0).5 (0.0). (0.) Typ.00 (0.0) Typ.000 (0.) Typ.00 (0.0).000 Typ See Pixel Detail A (0.).00 (0.).005 (0.0) Typ.006 (0.0) Typ.00 G B (0.).00 (6.).66 x (0.) Dia.05 (.0).0 Typ.6 (5.5).0 (.).5 (.0) x (0.) Dia.05 Landless x (.05) Dia.0 sales@greatecs.com 5

6 TIMING SPECIFICATIONS FO SMATSWITCH & SMATDISPLAY AC Characteristics (Temperature at 5 C), V DD =.V ~.5V) Items Symbols Minimum Typical Maximum Clock Cycle Time tcycle 50ns Setup Time tas 0ns tas tah Hold Time tah 0ns SS tcss tcsh SS Setup Time tcss 5ns SS Hold Time tcsh 60ns SCK t tc LKH tcycle Write Data Setup Time tdsw 0ns tf tc LKL Write Data Hold Time tdhw 0ns SCK Low Time tclkl 5ns tdsw tdhw D D6 D5 D D D D D0 SCK High Time tclkh 5ns SCK ise Time t 5ns SCK Fall Time tf 5ns STATE TANSITION : Initialization State 0 Power OFF (VCC, VDD OFF) : Power ON, : Initialization : Power OFF State Display OFF () : Display ON : Display OFF State Display ON : Changing the Display : Changing the Display State Number State Display Sleep V CC V D D Changing the Display 0 Power OFF OFF OFF OFF Disable Display OFF OFF ON ON ON Enable Display ON ON OFF ON ON Enable State 0 Power ON/OFF Sequence Initialization Setting Power ON State State Power OFF State 0 Minimum 0µs Minimum 0µs V DD 0V State Transition Transition Index eset low pulse width Trw (minimum µs) Power ON ES Power OFF Display ON efer to "Power ON/OFF Sequence" Minimum µs Minimum 0µs Display OFF Initialization Initialize Setting of Command/Data Image ewriting Send Display Data Display Settings Dimmer, Scroll, etc. V CC SS SCK VDD level (due to ESD protection circuit between VDD and VCC) H or L sales@greatecs.com 6

7 PECAUTIONS FO HANDLING & STOAGE ATTENTION ELECTOST AT IC SENSITIVE DEVICES Handling. The OLED devices are electrostatic sensitive. To avoid damage to IC, do not touch keytops unless properly isolated from static electricity.. Signal input under conditions not recommended may cause damage to the OLED unit or deterioration of the display. Follow directions regarding supply sequences of power and signal voltages.. If the OLED panel is broken, avoid contact with the contents and wash off any spills to the skin or clothing.. Limit operating force to switch keytop to 00.0N maximum, as excessive pressure may damage the OLED. 5. For OLED display, it is necessary for terminal of metal cover to be connected to a ground. 6. ecommended soldering time and temperature limits for OLED switch or display: seconds 0 C maximum; avoid temperatures exceeding 0 C at the OLED.. The IS series OLED devices are not process sealed.. If OLED unit is operated with the same display pattern, the difference between the operation duration of adjacent pixels may be interpreted as difference between luminosity of pixels. To minimize this difference, operate OLED unit so that each pixel may be turned on at frequency as equal as possible.. For switch, clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. For display, avoid contact with any flux or detergent. If any liquids spill on display surface, immediately wipe with soft absorbent cloth. Storage. Store in original container and away from direct sunlight.. Keep away from static electricity.. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. sales@greatecs.com