CERTIFICATE OF APPROVAL No CF 694 3M UK LTD

Transcription

1 CERTIFICATE OF APPROVAL No CF 694 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of 3M Centre, Cain Road, Bracknell, Berkshire, RG12 8HT Tel: Fax: Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions appended hereto: CERTIFIED PRODUCT 3M 2000 Coating TECHNICAL SCHEDULE TS03 Penetration Sealing Systems Signed and sealed for and on behalf of CERTIFIRE Sir Ken Knight Issued: 12 th June 2009 Chairman - Management Council Page 1 of 5

2 3M 2000 Coating CERTIFICATE No CF This relates to the use of 3M 2000 Coating (in conjunction with 3M Board) for the fire protection where services are penetrating s. The detailed scope is given in the Approval Matrix included in this Certificate. This shows the thickness and acceptable services for 3M 2000 Coating penetration sealing systems, required to provide fire resistance periods in accordance with BS EN : 2004 of up to 240 minutes for differing services and constructions. 2. This certification is designed to demonstrate compliance of the product or system specifically with Approved Document B (England and Wales), Section 2 of the Technical Standards (Scotland), Technical Booklet E (N. Ireland). If compliance is required to other regulatory or guidance documents there may be additional considerations or conflict to be taken into account. 3. The product is approved on the basis of: i) Initial type testing ii) Audit testing at the frequency specified in TS03 iii) A design appraisal against TS03 iv) Inspection and surveillance of factory production control v) Production surveillance under ISO 9001: The stud partition drys, masonry or concrete s shall be at least 150 mm thick and have at least the same fire rating as that required for the penetration seal. 5. The services which may be fitted through the seals are cable trays/ladders, cables and metallic pipes as detailed within the Approval Matrix included in this Certificate. 6. The relates to ongoing production. Product and/or its immediate packaging is identified with the manufacturers name, the product name or number, the CERTIFIRE name or name and mark, together with the CERTIFIRE certificate number and application where appropriate. Page 2 of 5 Signed Issued: 12 th June 2009

3 3M 2000 Coating Approval Matrix - Up To 90 minutes 3M 2000 Coating with 3M Board 90 min system Cable Tray (450 mm wide by 25 mm high max.) Single core power cables - 26mm 90 minutes 45 minutes Multi-core power cables - 26mm Multi-core power cables - 80mm Steel pipes up to 34mm & 3.5mm pipe Copper pipes up to 15mm and 1.5mm pipe Steel pipes up to 34mm & 3.5mm pipe Copper pipes up to 15 mm and 1.5mm pipe with 19mm thick closed cell elastomeric nitrile rubber Blank seals Maximum unsupported area (without services or blank seal) mm 600mm wide by 300mm high Drys shall be minimum 150 mm thick and incorporate minimum 2 layers of 12.5 mm thick Type F gypsum boards on both faces. Apertures to be framed with metal stud sections. Masonry/block/concrete s shall be minimum of 150 mm thick/650 kg/m 3. Concrete/masonry s & drys:. Board to aperture junction and butt joints are sealed with 3M 2000 Coating. Apertures for penetrating cables/trays are to be tightly fitting and be sealed/ made good with 3M 2000 coating. Min. 150 mm by 1mm dry thickness for all services not further than 230 mm and 450 mm from both faces of the sealing system. Page 3 of 5 Signed Issued: 12 th June 2009

4 3M 2000 Coating Approval Matrix - Up To 120 minutes 3M 2000 Coating with 3M Board 120 min system Cable Tray (450 mm wide by 25 mm high max.) 120 minutes 60 minutes 120 minutes 60 minutes Single core power cables - 26mm 120 minutes 30 minutes Multi-core power cables - 26mm 120 minutes 60 minutes Multi-core power cables - 80mm 120 minutes 120 minutes Steel pipes up to 34mm & 3.5mm pipe 120 minutes 90 minutes Copper pipes up to 15mm and 1.5mm pipe Steel pipes up to 34mm & 3.5mm pipe Copper pipes up to 15 mm and 1.5mm pipe with 19mm thick closed cell elastomeric nitrile rubber 120 minutes 60 minutes 120 minutes 120 minutes 120 minutes 120 minutes Blank seals 120 minutes 120 minutes Maximum unsupported area (without services or blank seal) mm 600mm wide by 300mm high Drys shall be minimum 150 mm thick and incorporate minimum 2 layers of 12.5 mm thick Type F gypsum boards on both faces. Apertures to be framed with metal stud sections. Masonry/block/concrete s shall be minimum of 150 mm thick/650 kg/m 3. Concrete/masonry s & drys:. Board to aperture junction and butt joints are sealed with 3M 2000 Coating. Apertures for penetrating cables/trays are to be tightly fitting and be sealed/ made good with 3M Fire Barrier IC 15 WB+ Sealant. Min. 100 mm by 1mm dry thickness for all services not further than 250 mm and 450 mm from both faces of the sealing system. Page 4 of 5 Signed Issued: 12 th June 2009

5 3M 2000 Coating Approval Matrix - Up To 240 minutes 3M 2000 Coating with 3M Board 240 min system Cable Tray (450 mm wide by 25 mm high max.) 240 minutes 240 minutes 240 minutes 90 minutes Single core power cables - 26mm 240 minutes 60 minutes Multi-core power cables - 26mm 240 minutes 90 minutes Steel pipes up to 34mm & 3.5mm pipe 240 minutes 120 minutes Copper pipes up to 15mm and 1.5mm pipe Steel pipes up to 34mm & 3.5mm pipe Copper pipes up to 15 mm and 1.5mm pipe with 19mm thick closed cell elastomeric nitrile rubber 240 minutes 45 minutes 240 minutes 240 minutes 240 minutes 180 minutes Blank seals 240 minutes 240 minutes Maximum unsupported area (without services or blank seal) mm 600mm wide by 300mm high Masonry/block/concrete s shall be minimum of 150 mm thick/650 kg/m 3. Concrete/masonry s:. Board to aperture junction and butt joints are sealed with 3M Fire Barrier IC 15 WB+ Sealant. Apertures for penetrating cables/trays are to be tightly fitting and be sealed/ made good with 3M Fire Barrier IC 15 WB+ Sealant. Min. 100 mm length by 1mm dry thickness for all services not further than 280 mm and 420 mm from both faces of the sealing system. Page 5 of 5 Signed Issued: 12 th June 2009