EVALUATION SUBJECT: PLASTIC COMPRESSION FITTINGS DIVISION: PLUMBING SECTION: DOMESTIC WATER PIPING. Report Holder: PHILMAC PTY LTD

Transcription

1 ICC-ES Report PMG-1253 Reissued 11/2017 This report is subject to renewal 11/2018 EVALUATION SUBJECT: PLASTIC COMPRESSION FITTINGS DIVISION: PLUMBING SECTION: DOMESTIC WATER PIPING Report Holder: PHILMAC PTY LTD DEEDS ROAD NORTH PLYMPTON 5037 SOUTH AUSTRALIA, AUSTRALIA

2 ICC-ES PMG Product Certificate PMG-1253 Effective Date: November 2017 This listing is subject to re-examination in one year. (800) (562) A Subsidiary of the International Code Council CSI: Division: Plumbing Section: Domestic Water Piping Product certification system: The ICC-ES product certification system includes testing samples taken from the market or supplier s stock, or a combination of both, to verify compliance with applicable codes and standards. The system also involves factory inspections, and assessment and surveillance of the supplier s quality system. Products: Listee: Plastic Compression Fittings Philmac Pty Ltd Deeds Road North Plympton 5037 South Australia, Australia Compliance with the following codes: 2018, 2015, 2012, 2009 and 2006 International Plumbing Code (IPC) 2018, 2015, 2012, 2009 and 2006 International Residential Code (IRC) 2015, 2012, 2009 and 2006 Uniform Plumbing Code (UPC)* 2015, 2010 and 2005 National Plumbing Code of Canada (NPC)** *Uniform Plumbing Code is a copyrighted publication of the International Association of Plumbing and Mechanical Officials **National Plumbing Code of Canada is a copyrighted publication of National Research Council Canada Compliance with the following standards: Identification: CSA B , Polyethylene (PE) Pipe, Tubing, and Fittings for Cold-water Pressure Services NSF/ANSI , Drinking Water System Components Health Effects Fittings shall be marked with at least the following: (a) the manufacturer s name or trademark; (b) nominal size (c) the material designation (PP-B), if applicable; (d) the CSA B137.1 (e) the intended service, where applicable (e.g., GAS, potable, P, or PW ) (f) the ICC-ES PMG listing mark Markings on fittings shall be permanent or indelible in legible letters and numerals, and of a color that contrasts with the color of the fitting. Markings may be molded onto the exterior surface, preferably on the body or the hub, or may be on a permanent stick-on label. Listings are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the listing or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this listing, or as to any product covered by the listing. Copyright 2017 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 13

3 PMG-1253 Most Widely Accepted and Trusted Page 2 of 13 Installation: Models: Plastic Compression Fittings must be installed in accordance with the manufacturer s published installation instructions, the applicable codes and this listing. Where differences exist, the applicable codes must govern. 3G TM CTS Compression Fittings for use with Polyethylene (PE) plastic pipe are manufactured from Polypropylene Block Copolymer (PP-B). 3GTM CTS Compression Fittings comply with CSA B137.1 and NSF/ANSI 61. Model # Description COUPLING 3G CTS 3/4" COUPLING 3G CTS 1" COUPLING 3G CTS 1-1/4" COUPLING 3G CTS 1-1/2" COUPLING 3G CTS 2" COUPLING RED 3G CTS 1"x3/4" MI ADAPTOR 3G CTS 3/4"x1/2" MI ADAPTOR 3G CTS 3/4"x3/4" MI ADAPTOR 3G CTS 1"x1/2" MI ADAPTOR 3G CTS 1"x3/4" MI ADAPTOR 3G CTS 1"x1" MI ADAPTOR 3G CTS 1-1/4"x3/4" MI ADAPTOR 3G CTS 1-1/4"x1" MI ADAPTOR 3G CTS 1-1/4"x1-1/4" MI ADAPTOR 3G CTS 1-1/2"x1" MI ADAPTOR 3G CTS 1-1/2"x1-1/4" MI ADAPTOR 3G CTS 1-1/2"x1-1/2" MI ADAPTOR 3G CTS 2"x1-1/2" MI ADAPTOR 3G CTS 2"x2" FI ADAPTOR 3G CTS 3/4"x1/2" FI ADAPTOR 3G CTS 3/4"x3/4" FI ADAPTOR 3G CTS 1"x3/4" FI ADAPTOR 3G CTS 1"x1" FI ADAPTOR 3G CTS 1-1/4"x1" FI ADAPTOR 3G CTS 1-1/4"x1-1/4" FI ADAPTOR 3G CTS 1-1/2"x1-1/4" FI ADAPTOR 3G CTS 1-1/2"x1-1/2" FI ADAPTOR 3G CTS 2"x1-1/2" FI ADAPTOR 3G CTS 2"x2" ELBOW 3G CTS 3/4" ELBOW 3G CTS 1" ELBOW 3G CTS 1-1/4" ELBOW 3G CTS 1-1/2" ELBOW 3G CTS 2" FI ELBOW 3G CTS 3/4"x3/4" FI ELBOW 3G CTS 1"x3/4" FI ELBOW 3G CTS 1"x1"

4 PMG-1253 Most Widely Accepted and Trusted Page 3 of FI ELBOW 3G CTS 1-1/4"x1" FI ELBOW 3G CTS 1-1/4"x1-1/4" FI ELBOW 3G CTS 1-1/2"x1-1/4" FI ELBOW 3G CTS 1-1/2"x1-1/2" TEE 3G CTS 3/4" TEE 3G CTS 1" TEE 3G CTS 1-1/4" TEE 3G CTS 1-1/2" FI TEE 3G CTS 3/4"x3/4" FI TEE 3G CTS 1"x3/4" FI TEE 3G CTS 1"x1" FI TEE 3G CTS 1-1/4"x3/4" FI TEE 3G CTS 1-1/4"x1" FI TEE 3G CTS 1-1/4"x1-1/4" FI TEE 3G CTS 1-1/2"x3/4" FI TEE 3G CTS 1-1/2"x1-1/4" FI TEE 3G CTS 1-1/2"x1-1/2" COUPLING RED 3G CTS 1-1/4"x1" COUPLING Red. 3G CTS 1-1/4"x3/4" COUPLING Red. 3G CTS 1-1/2"x1" COUPLING Red. 3G CTS 1-1/2"x1-1/4" END CAP 3G CTS 3/4" END CAP 3G CTS 1" END CAP 3G CTS 1-1/4" END CAP 3G CTS 1-1/2" END CAP 3G CTS 3/4" END CAP 3G CTS 1" END CAP 3G CTS 1-1/4" END CAP 3G CTS 1-1/2" COUPLING 3G CTS 3/4" SLIP COUPLING 3G CTS 3/4" COUPLING RED 3G CTS 1" x 3/4" COUPLING 3G CTS 1" SLIP COUPLING 3G CTS 1" COUPLING RED 3G CTS 1-1/4"x1" COUPLING 3G CTS 1-1/4" COUPLING 3G CTS 1-1/2" COUPLING 3G CTS 2" MI ADAPTOR 3G CTS 3/4x1/2" MI ADAPTOR 3G CTS 3/4x3/4" MI ADAPTOR 3G CTS 1"x1/2" MI ADAPTOR 3G CTS 1"x3/4" MI ADAPTOR 3G CTS 1"x1" MI ADAPTOR 3G CTS 1-1/4"x3/4" MI ADAPTOR 3G CTS 1-1/4"x1" MI ADAPTOR 3G CTS 1-1/4"x1-1/4" MI ADAPTOR 3G CTS 1-1/2" x 1"

5 PMG-1253 Most Widely Accepted and Trusted Page 4 of MI ADAPTOR 3G CTS 1-1/2"x1-1/4" MI ADAPTOR 3G CTS 1-1/2"x1-1/2" MI ADAPTOR 3G CTS 2"x1-1/2" MI ADAPTOR 3G CTS 2" x 2" TEE 3G CTS 3/4" REDUCING TEE 3G CTS 1" x 3/4" TEE 3G CTS 1" REDUCING TEE 3G CTS 1" x 1-1/4" REDUCING TEE 3G CTS 1-1/4" x 1" TEE 3G CTS 1-1/4" REDUCING TEE 3G CTS 1-1/2" x 1" REDUCING TEE 3G CTS 1-1/2" x 1-1/4" TEE 3G CTS 1-1/2" FI TEE 3G CTS 3/4" x 1/2" FI TEE 3G CTS 3/4" x 3/4" FI TEE 3G CTS 1" x 1/2" FI TEE 3G CTS 1" x 3/4" FI TEE 3G CTS 1" x 1" FI TEE 3G CTS 1-1/4" x 1/2" FI TEE 3G CTS 1-1/4" x 3/4" FI TEE 3G CTS 1-1/4" x 1" FI TEE 3G CTS 1-1/4" x 1-1/4" FI TEE 3G CTS 1-1/2" x 1/2" FI TEE 3G CTS 1-1/2" x 3/4" FI TEE 3G CTS 1-1/2" x 1-1/4" FI TEE 3G CTS 1-1/2" x 1-1/2" ELBOW 3G CTS 3/4" REDUCING ELBOW 3G CTS 1" x 3/4" ELBOW 3G CTS 1" ELBOW 3G CTS 1-1/4" ELBOW 3G CTS 1-1/2" ELBOW 3G CTS 2" FI ELBOW 3G CTS 3/4x1/2" FI ELBOW 3G CTS 3/4" x3/4" FI ELBOW 3G CTS 1" x 1/2" FI ELBOW 3G CTS 1"x3/4" FI ELBOW 3G CTS 1" x 1" FI ELBOW 3G CTS 1-1/4x1" FI ELBOW 3G CTS 1-1/4x1-1/4" FI ELBOW 3G CTS 1-1/2x1-1/4" FI ELBOW 3G CTS 1-1/2x1-1/2" FI ELBOW 3G CTS 2"x2" MI ELBOW 3G CTS 3/4" x 1/2" MI ELBOW 3G CTS 1" x 3/4" FI ADAPTOR 3G CTS 3/4"x1/2" FI ADAPTOR 3G CTS 3/4"x3/4" FI ADAPTOR 3G CTS 1"x1/2"

6 PMG-1253 Most Widely Accepted and Trusted Page 5 of FI ADAPTOR 3G CTS 1"x3/4" FI ADAPTOR 3G CTS 1" x 1" FI ADAPTOR 3G CTS 1-1/4"x3/4" FI ADAPTOR 3G CTS 1-1/4"x1" FI ADAPTOR 3G CTS 1-1/4"x1-1/4" FI ADAPTOR 3G CTS 1-1/2"x1-1/4" FI ADAPTOR 3G CTS 1-1/2"x1-1/2" FI ADAPTOR 3G CTS 2"x1-1/2" FI ADAPTOR 3G CTS 2" x 2" MI TEE 3G CTS 1" x 1/2" MI TEE 3G CTS 1" x 3/4" Universal Transition Couplings (UTC) are manufactured from Polypropylene Block Copolymer (PP-B) material. Universal Transition Couplings comply with NSF/ANSI 61. Model # Description ELBOW UTC x 15-21mm ELBOW UTC x 21-27mm TEE UTC 15-21mm x (3) FI TEE UTC 15-21mm x 3/4" FIPT FI TEE UTC 15-21mm x 1" FIPT FI TEE UTC 21-27mm x 3/4" FIPT FI TEE UTC 21-27mm x 1" FIPT MI ADAPTER UTC 15-21mm x 3/4" MIPT MI ADAPTER UTC 27-34mm x 1" MIPT COUPLING RED UTC x 27-34mm COUPLING UTC x 15-21mm COUPLING UTC x 21-27mm COUPLING UTC x 27-34mm COUPLING UTC x 39-43mm COUPLING RED UTC x 15-21mm COUPLING RED UTC x 21-27mm COUPLING RED UTC x 15-21mm COUPLING RED UTC x 27-34mm MI ADAPTER UTC 21-27mm x 3/4" MIPT MI ADAPTER UTC 27-34mm x 3/4" MIPT COUPLING UTC x 34-39mm COUPLING UTC x 47-49mm COUPLING UTC x 59-61mm MI ADAPTOR UTC 15-21mm x 3/4" MI ADAPTOR UTC 21-27mm x 3/4" MI ADAPTOR UTC 21-27mm x 1" NPT MI ADAPTOR UTC 27-34mm x 3/4" MI ADAPTOR UTC 27mm-34mm x1" NPT ELBOW UTC 15-21mm x 15-21mm ELBOW UTC 21-27mm x 21-27mm COUPLING UTC 15-21mm x 15-21mm COUPLING UTC 21-27mm x 15-21mm

7 PMG-1253 Most Widely Accepted and Trusted Page 6 of COUPLING UTC 21-27mm x 21-27mm COUPLING UTC 27-34mm x 15-21mm COUPLING UTC 27-34mm x 21-27mm COUPLING UTC 27-34mm x 27-34mm COUPLING UTC 39-43mm x 27-34mm COUPLING UTC 39-43mm x 39-43mm COUPLING UTC x COUPLING UTC 34-39mm x 34-39mm COUPLING UTC x COUPLING UTC 47-49mm x 47-49mm COUPLING UTC 59-61mm x 59-61mm TEE UTC 15-21mm FI TEE UTC 15-21mm x 3/4" FI TEE UTC 21-27mm x 3/4" 3G TM ID Series Compression Fittings are manufactured from Polypropylene Block Copolymer (PP-B) 3G TM ID Series Compression Fittings comply with NSF/ANSI 61. Model # Description COUPLING 3G ID 1/2" COUPLING 3G ID 3/4" COUPLING 3G ID 1" COUPLING 3G ID 1-1/4" COUPLING 3G ID 1-1/2" COUPLING 3G ID 2" COUPLING RED 3G ID 3/4"x1/2" MI ADAPTOR 3G ID 1/2"x1/2" COUPLING RED 3G ID 3/4"x1/2" MI ADAPTOR 3G ID 1/2"x1/2" MI ADAPTOR 3G ID 1/2"x3/4" MI ADAPTOR 3G ID 3/4"x1/2" MI ADAPTOR 3G ID 3/4"x3/4" MI ADAPTOR 3G ID 3/4"x1" MI ADAPTOR 3G ID 1"x3/4" MI ADAPTOR 3G ID 1"x1" MI ADAPTOR 3G ID 1"x1-1/4" MI ADAPTOR 3G ID 1-1/4"x1" MI ADAPTOR 3G ID 1-1/4"x1-1/4" MI ADAPTOR 3G ID 1-1/4"x1-1/2" MI ADAPTOR 3G ID 1-1/2"x1-1/2" MI ADAPTOR 3G ID 1-1/2"x2" MI ADAPTOR 3G ID 2"x2" FI ADAPTOR 3G ID 1/2"x1/2" FI ADAPTOR 3G ID 1/2"x3/4" FI ADAPTOR 3G ID 3/4"x3/4" FI ADAPTOR 3G ID 3/4"x1" FI ADAPTOR 3G ID 1"x1" FI ADAPTOR 3G ID 1"x1-1/4"

8 PMG-1253 Most Widely Accepted and Trusted Page 7 of FI ADAPTOR 3G ID 1-1/4"x1-1/4" FI ADAPTOR 3G ID 1-1/4"x1-1/2" FI ADAPTOR 3G ID 1-1/2"x1-1/2" FI ADAPTOR 3G ID 1-1/2"x2" FI ADAPTOR 3G ID 2"x2" ELBOW 3G ID 1/2" ELBOW 3G ID 3/4" ELBOW 3G ID 1" ELBOW 3G ID 1-1/4" ELBOW 3G ID 1-1/2" ELBOW 3G ID 2" FI ELBOW 3G ID 1/2"x3/4" FI ELBOW 3G ID 3/4"x3/4" FI ELBOW 3G ID 3/4"x1" FI ELBOW 3G ID 1"x1" FI ELBOW 3G ID 1"x1-1/4" TEE 3G ID 1/2" TEE 3G ID 3/4" TEE 3G ID 1" TEE 3G ID 1-1/4" TEE 3G ID 1-1/2" FI TEE 3G ID 3/4"x3/4" FI TEE 3G ID 1"x1/2" FI TEE 3G ID 1"x1" FI TEE 3G ID 1-1/4"x1/2" FI TEE 3G ID 1-1/4"x3/4" FI TEE 3G ID 1-1/4"x1-1/2" FI TEE 3G ID 1-1/2"x2" END CAP 3G ID 1/2" END CAP 3G ID 3/4" END CAP 3G ID 1" END CAP 3G ID 1-1/4" END CAP 3G ID 1-1/2" FI ELBOW 3G ID 1-1/4"x1-1/4" JOINT KIT 3G IPS ID 1/2" JOINT KIT 3G IPS ID 3/4" JOINT KIT 3G IPS ID 1" JOINT KIT 3G IPS ID 1-1/4" JOINT KIT 3G IPS ID 1-1/2" JOINT KIT 3G IPS ID 2" COUPLING RED 3G ID 1"x1/2" COUPLING RED 3G ID 1"x3/4" COUPLING RED 3G ID 1-1/4"x3/4" COUPLING RED 3G ID 1-1/4"x1" COUPLING RED 3G ID 1-1/2"x3/4" COUPLING RED 3G ID 1-1/2"x1" COUPLING RED 3G ID 1-1/2"x1-1/4"

9 PMG-1253 Most Widely Accepted and Trusted Page 8 of COUPLING RED 3G ID 2"x1" COUPLING RED 3G ID 2"x1-1/4" COUPLING RED 3G ID 2"x1-1/2" TEE RED 3G ID 1-1/4"x3/4" TEE RED 3G ID 2"x1" END CAP 3G ID 2" BLANKING PLUG - SIZE BLANKING PLUG - SIZE BLANKING PLUG - SIZE BLANKING PLUG - SIZE BLANKING PLUG - SIZE BLANKING PLUG - SIZE FI ELBOW 3G ID 2"x2" TEE 3G ID 2" FI TEE 3G ID 1-1/2"x1-1/2" FI TEE 3G ID 2"x2" O RING BS NSF 061 SIDR O RING BS NSF 061 SIDR O RING BS NSF 061 SIDR O RING BS NSF O RING BS NSF O RING BS NSF SPLIT COLLET PG CAN NO SPLIT COLLET PG CAN No SPLIT COLLET PG CAN NO SPLIT COLLET PG CAN NO SPLIT COLLET PG CAN NO SPLIT COLLET PG CAN NO NUT 3G ID SERIES (2) 1/2" INSERT 3G ID SERIES (2) 1/2" NUT 3G ID SERIES (3) 3/4" INSERT 3G ID SERIES (3) 3/4" NUT 3G ID SERIES (4) 1" INSERT 3G ID SERIES (4) 1" NUT 3G ID SERIES (5) 1-1/4" INSERT 3G ID SERIES (5) 1-1/4" NUT 3G ID SERIES (6) 1-1/2" INSERT 3G ID SERIES (6) 1-1/2" NUT 3G ID SERIES (7) 2" INSERT 3G ID SERIES (7) 2" END CAP 3G ID SERIES 1/2" END CAP 3G ID SERIES 3/4" END CAP 3G ID SERIES 1" END CAP 3G ID SERIES 1-1/4" END CAP 3G ID SERIES 1-1/2" END CAP 3G ID SERIES 2" COUPLING 3G ID SERIES 1/2"

10 PMG-1253 Most Widely Accepted and Trusted Page 9 of COUPLING REDUCING 3G ID SERIES 3/4"x1/2" COUPLING 3G ID SERIES 3/4" COUPLING 3G ID SERIES 1" COUPLING 3G ID SERIES 1-1/4" COUPLING 3G ID SERIES 1-1/2" COUPLING REDUCING 3G ID SERIES 2" x 1" COUPLING REDUCING 3G ID SERIES 2" x 1-1/4" COUPLING REDUCING 3G ID SERIES 2" x 1-1/2" COUPLING 3G ID SERIES 2" MI ADAPTOR 3G ID SERIES 1/2"x1/2" MI ADAPTOR 3G ID SERIES 1/2"x3/4" MI ADAPTOR 3G ID SERIES 3/4"x1/2" MI ADAPTOR 3G ID SERIES 3/4"x3/4" MI ADAPTOR 3G ID SERIES 3/4"x1" MI ADAPTOR 3G ID SERIES 1"x3/4" MI ADAPTOR 3G ID SERIES 1"x1" MI ADAPTOR 3G ID SERIES 1"x1-1/4" MI ADAPTOR 3G ID SERIES 1-1/4"x1" MI ADAPTOR 3G ID SERIES 1-1/4"x1-1/4" MI ADAPTOR 3G ID SERIES 1-1/4"x1-1/2" MI ADAPTOR 3G ID SERIES 1-1/2"x1-1/2" MI ADAPTOR 3G ID SERIES 1-1/2"x2" MI ADAPTOR 3G ID SERIES 2"x2" TEE 3G ID SERIES 1/2" TEE 3G ID SERIES 3/4" TEE 3G ID SERIES 1" TEE 3G ID SERIES 1-1/4" TEE 3G ID SERIES 1-1/2" TEE 3G ID SERIES 2" FI TEE 3G ID SERIES 3/4" x 3/4" FI TEE 3G ID SERIES 1" x 1/2" FI TEE 3G ID SERIES 1" x 1" FI TEE 3G ID SERIES 1-1/4" x 1/2" FI TEE 3G ID SERIES 1-1/4" x 3/4" FI TEE 3G ID SERIES 1-1/4" x 1-1/2" FI TEE 3G ID SERIES 1-1/2" x 2" FI TEE 3G ID SERIES 2" x 2" ELBOW 3G ID SERIES 1/2" ELBOW 3G ID SERIES 3/4" ELBOW 3G ID SERIES 1" ELBOW 3G ID SERIES 1-1/4" ELBOW 3G ID SERIES 1-1/2" ELBOW 3G ID SERIES 2" FI ELBOW 3G ID SERIES 3/4" x 3/4" FI ELBOW 3G ID SERIES 3/4" x 1" FI ELBOW 3G ID SERIES 1" x 1" FI ELBOW 3G ID SERIES 1" x 1-1/4"

11 PMG-1253 Most Widely Accepted and Trusted Page 10 of FI ELBOW 3G ID SERIES 1-1/4" x 1-1/4" FI ELBOW 3G ID SERIES 2" x 2" FI ADAPTOR 3G ID SERIES 1/2"x1/2" FI ADAPTOR 3G ID SERIES 1/2"x3/4" FI ADAPTOR 3G ID SERIES 3/4"x3/4" FI ADAPTOR 3G ID SERIES 3/4"x1" FI ADAPTOR 3G ID SERIES 1"x1" FI ADAPTOR 3G ID SERIES 1"x1-1/4" FI ADAPTOR 3G ID SERIES 1-1/4"x1-1/4" FI ADAPTOR 3G ID SERIES 1-1/4"x1-1/2" FI ADAPTOR 3G ID SERIES 1-1/2"x1-1/2" FI ADAPTOR 3G ID SERIES 1-1/2"x2" FI ADAPTOR 3G ID SERIES 2"x2" 3G TM OD Series Compression Fittings are manufactured from Polypropylene Block Copolymer (PP-B) 3G TM OD Series Compression Fittings comply with CSA B137.1 and NSF/ANSI 61. Model # Description MI ADPTR 3G IPS-OD 3/4"x3/4" MI ADPTR 3G IPS-OD 1"x1" MI ADPT 3G IPS-OD 1-1/4"x1-1/4" MI ADPT 3G IPS-OD 1-1/2"x1-1/2" MI ADPTR 3G IPS-OD 2"x2" Tee 3G IPS-OD 1" Tee 3G IPS-OD 1-1/4" Tee 3G IPS-OD 1-1/2" Elbow 3G IPS-OD 1" Elbow 3G IPS-OD 1-1/4" Elbow 3G IPS-OD 1-1/2" Coupling 3G IPS-OD 3/4" Coupling 3G IPS-OD 1" Coupling 3G IPS-OD 1-1/4" Coupling 3G IPS-OD 1-1/2" Coupling 3G IPS-OD 2" TEE RED 3G IPS OD 2" x 3/4" TEE RED 3G IPS OD 2" x 1" END CAP IPS OD 2" COUPLING IPS-OD 2" COUPLING SLIP IPS-OD 2" ADAPTOR MI IPS OD 2" x 2" NPT TEE IPS-OD 2" TEE FI IPS-OD 2" x 1-1/2" ACME TEE SLIP FI IPS-OD 2" x 1-1/2"ACME TEE FI IPS OD 2" x 2" NPT ELBOW IPS-OD 2" ELBOW FI IPS-OD 2" x 1-1/2" ACME ADAPTOR FI IPS OD 2" x 2" NPT END CAP 3G IPS-OD 1/2" END CAP 3G IPS-OD 3/4"

12 PMG-1253 Most Widely Accepted and Trusted Page 11 of END CAP 3G IPS-OD 1" END CAP 3G IPS-OD 1-1/4" END CAP 3G IPS-OD 1-1/2" COUPLING 3G IPS-OD 1/2" SLIP COUPLING 3G IPS-OD 1/2"x1/2" COUPLING REDUCING 3G IPS-OD 3/4"x1/2" COUPLING 3G IPS-OD 3/4" SLIP COUPLING 3G IPS-OD 3/4"x3/4" COUPLING REDUCING 3G IPS-OD 1" x 1/2" COUPLING REDUCING 3G IPS-OD 1" x 3/4" COUPLING 3G IPS-OD 1" SLIP COUPLING 3G IPS-OD 1"x1" COUPLING REDUCING 3G IPS-OD 1-1/4" x 3/4" COUPLING RED 3G IPS-OD 1-1/4" x 1" COUPLING 3G IPS-OD 1-1/4" SLIP COUPLING 3G IPS-OD 1-1/4"x1-1/4" COUPLING REDUCING 3G IPS-OD 1-1/2" x 3/4" COUPLING REDUCING 3G IPS-OD 1-1/2" x 1" COUPLING REDUCING 3G IPS-OD 1-1/2" x 1-1/4" COUPLING 3G IPS-OD 1-1/2" SLIP COUPLING 3G IPS-OD 1-1/2"x1-1/2" COUPLING REDUCING 3G IPS-OD 2" x 1" COUPLING REDUCING 3G IPS-OD 2" x 1-1/4" COUPLING REDUCING 3G IPS-OD 2" x 1-1/2" MI ADAPTOR 3G IPS-OD 1/2"x1/2" MI ADAPTOR 3G IPS-OD 1/2"x3/4" MI ADAPTOR 3G IPS-OD 3/4"x1/2" MI ADAPTOR 3G IPS-OD 3/4"x3/4" MI ADAPTOR 3G IPS-OD 3/4"x1" MI ADAPTOR 3G IPS-OD 1"x3/4" MI ADAPTOR 3G IPS-OD 1"x1" MI ADAPTOR 3G IPS-OD 1"x1-1/4" MI ADAPTOR 3G IPS-OD 1-1/4"x1" MI ADAPTOR 3G IPS-OD 1-1/4"x1-1/4" MI ADAPTOR 3G IPS-OD 1-1/4"x1-1/2" MI ADAPTOR 3G IPS-OD 1-1/2"x1-1/2" MI ADAPTOR 3G IPS-OD 1-1/2"x2" TEE 3G IPS-OD 1/2" REDUCING TEE 3G IPS-OD 3/4" x 1/2" TEE 3G IPS-OD 3/4" REDUCING TEE 3G IPS-OD 3/4" x 1" REDUCING TEE 3G IPS-OD 1" x 3/4" TEE 3G IPS-OD 1" REDUCING TEE 3G IPS-OD 1-1/4" x 3/4" REDUCING TEE 3G IPS-OD 1-1/4" x 1" TEE 3G IPS-OD 1-1/4" REDUCING TEE 3G IPS-OD 1-1/2" x 3/4"

13 PMG-1253 Most Widely Accepted and Trusted Page 12 of REDUCING TEE 3G IPS-OD 1-1/2" x 1" REDUCING TEE 3G IPS-OD 1-1/2" x 1-1/4" TEE 3G IPS-OD 1-1/2" REDUCING TEE 3G IPS-OD 2" x 3/4" REDUCING TEE 3G IPS-OD 2" x 1" REDUCING TEE 3G IPS-OD 2" x 1-1/2" FI TEE 3G IPS-OD 1/2" x 1/2" FI TEE 3G IPS-OD 1/2" x 3/4" FI TEE 3G IPS-OD 3/4" x 1/2" FI TEE 3G IPS-OD 3/4" x 3/4" FI TEE 3G IPS-OD 3/4" x 1" FI TEE 3G IPS-OD 1" x 1/2" FI TEE 3G IPS-OD 1" x 3/4" FI TEE 3G IPS-OD 1" x 1" FI TEE 3G IPS-OD 1" x 1-1/4" FI TEE 3G IPS-OD 1-1/4" x 1/2" FI TEE 3G IPS-OD 1-1/4" x 3/4" FI TEE 3G IPS-OD 1-1/4" x 1-1/4" FI TEE 3G IPS-OD 1-1/4" x 1-1/2" FI TEE 3G IPS-OD 1-1/2" x 1/2" FI TEE 3G IPS-OD 1-1/2" x 3/4" FI TEE 3G IPS-OD 1-1/2" x 1-1/2" FI TEE 3G IPS-OD 1-1/2" x 1-1/2" BSP FI TEE 3G IPS-OD 1-1/2" x 2" FI TEE 3G IPS-OD 1-1/2" x 2" BSP ELBOW 3G IPS-OD 1/2" ELBOW REDUCING 3G IPS-OD 3/4" x 1/2" ELBOW 3G IPS-OD 3/4" ELBOW 3G IPS-OD 1" ELBOW 3G IPS-OD 1-1/4" ELBOW 3G IPS-OD 1-1/2" FI ELBOW 3G IPS-OD 1/2" x 1/2" FI ELBOW 3G IPS-OD 1/2" x 3/4" FI ELBOW 3G IPS-OD 3/4" x 1/2" FI ELBOW 3G IPS-OD 3/4" x 3/4" FI ELBOW 3G IPS-OD 3/4" x 1" FI ELBOW 3G IPS-OD 1" x 1" FI ELBOW 3G IPS-OD 1" x 1-1/4" FI ELBOW 3G IPS-OD 1-1/4" x 1-1/4" FI ELBOW 3G IPS-OD 1-1/4" x 1-1/2" FI ELBOW 3G IPS-OD 1-1/2" x 1-1/2" FI ELBOW 3G IPS-OD 1-1/2" x 2" MI ELBOW 3G IPS-OD 1/2" x 1/2" MI ELBOW 3G IPS-OD 3/4" x 3/4" FI ADAPTOR 3G IPS-OD 1/2"x1/2" FI ADAPTOR 3G IPS-OD 1/2"x3/4" FI ADAPTOR 3G IPS-OD 3/4"x1/2"

14 PMG-1253 Most Widely Accepted and Trusted Page 13 of 13 Conditions of Listing: FI ADAPTOR 3G IPS-OD 3/4"x3/4" FI ADAPTOR 3G IPS-OD 3/4"x1" FI ADAPTOR 3G IPS-OD 1"x3/4" FI ADAPTOR 3G IPS-OD 1"x1" FI ADAPTOR 3G IPS-OD 1"x1-1/4" FI ADAPTOR 3G IPS-OD 1-1/4"x1-1/4" FI ADAPTOR 3G IPS-OD 1-1/4"x1-1/2" FI ADAPTOR 3G IPS-OD 1-1/2"x1-1/2" FI ADAPTOR 3G IPS-OD 1-1/2"x1-1/2" BSP FI ADAPTOR 3G IPS-OD 1-1/2"x2" MI TEE 3G IPS-OD 3/4" x 1/2" MI TEE 3G IPS-OD 3/4" x 3/4" 1. The fittings are only recognized for use with polyethylene pipe for cold water service. 2. The fittings are recognized for use with potable water. When installation is in fire-resistance-rated assemblies, evidence of compliance with IBC (penetrations) must be provided to the code official for approval. 3. Clearances from heat-producing equipment must be in accordance with the applicable code. 4. Plastic Compression Fittings must be installed in accordance with the manufacturer s published installation instructions, the applicable codes and this listing. Where differences exist, the applicable codes must govern. 5. Plastic Compression Fittings are manufactured by Philmac Pty Ltd in Australia, under a quality control program with annual surveillance inspection by ICC-ES.