Open Processor with Carrier CCN DataLink Driver

Transcription

1 Open Processor with Carrier CCN DataLink Driver Product Description Each Open Processor (Figure 1) contains the main processor, memory, and communications circuitry for connecting the APOGEE Automation System to the Carrier CCN Control system. Figure 1. Open Processor: Front View. The Open Processor attaches to the left mounting rail, the M-BUS rails, and the C-BUS slot of the MBC or RBC enclosure. An MBC or RBC enclosure is FCC-approved for a maximum of four Controller Modules and/or pre-apogee Open Processors, or a maximum of five APOGEE Open Processors. Product Numbers Open Processor with Carrier CCN DataLink Driver (APOGEE) Open Processor with Carrier CCN DataLink Driver (pre-apogee) Battery Replacement Kit. See ( ) MMI Extension Cable. See Installation Instructions ( ) Grounding Wire. Expected Installation Times 30 minutes. Required Tools And Materials Flat-blade screwdriver (1/8 inch blade width) Wire strippers Cabling and connectors. See the Connecting the Open Processor to the Carrier CCN Control System section. Black Box Corporation P/N IC109A: RS-232 to RS-485 Black Box Corporation P/N CMA02A: Communication Adapter CAUTION: Always wear an electro-static discharge wrist strap and discharge accumulated static before touching field panel components. Prerequisites MBC or RBC enclosure mounted with at least one open slot on the C-BUS and AC power connected. Two 120V receptacles to power the Black Boxes. Backups made of the current database for all Open Processors and other Controller Modules in the enclosure. Both systems installed and checked out by certified representatives of the companies that installed each system. These checkouts must confirm that each system is operating and ready to communicate with the other system. Building level network (BLN) cable, if used, fed into the MBC or RBC enclosure. If necessary, splice in a connector for the Open Processor. (Connecting this cable is done later during start-up.) Page1of6

2 Instructions Preparing to Install the Open Processor 1. Prepare the MBC or RBC enclosure for shutdown by performing the following steps: CAUTION: Figure 3. Open Processor: Rear View. Do not install or remove an Open Processor while the MBC or RBC enclosure is powered up. Doing so may damage the Open Processor or other modules in the enclosure. a. Notify the appropriate building personnel that you will be turning OFF power to the enclosure, and tell them what equipment will be affected. b. Follow all shutdown procedures necessary to prevent damage to any equipment orharm to any personnel. If the MBC or RBC enclosure already houses one or more Controller Modules and/or Open Processors, make sure their batteries are good. If any battery status LED is red when the power is ON, replace the battery before proceeding. 2. Turn OFF power to the MBC or RBC enclosure. 3. If you are installing the Open Processor in an empty MBC or RBC enclosure, remove the temporary cover (Figure 2) that is wrapped around the mounting rails, M-BUS rails, and the C-BUS. Save one connector for FLN 1 and one for the BLN if itisused. Figure 2. Temporary Cover. 4. Remove the C-BUS cover from the lowest available slot and discard it. 5. Remove any M-BUS protective tape from the M-BUS. 6. Remove the warning label from the Open Processor to expose the C-BUS card (Figure 3). Installing the Open Processor The goal of this procedure is to place the Open Processor s C-BUS and M-BUS connectors into their respective slots and secure the module. CAUTION: Improperly aligning and/or installing the Open Processor may damage it. 1. On the right-hand side of the Open Processor, locate the lower mounting guide (Figure 4). 2. Locate the round mounting rail on the far right edge of the right-hand M-BUS rail (Figure 4). 3. Align the module s lower mounting guide with the lowest available slot next to the round mounting rail (Figure 4). 4. Insert the lower and upper mounting guides into the mounting slot and hook them into place (Figure 4). 5. Push the left side of the Open Processor forward so that its C-BUS card edge and M-BUS connector mate with the C-BUS connector and M-BUS rails (Figure5). WhentheOpenProcessorisseated properly, you will hear a click. 6. If the Open Processor needs to be repositioned: a. Locate the module s latch (on the module s far left end). Release the latch by pulling it toward you. b. Swing the left end of the Open Processor towardyoutoremovethemodulefromits C-BUS slot (Figure 5). c. Pull on the Open Processor to remove its mounting guides from the round mounting rail (Figure 4). d. Repeat Steps 2 to 5 above. 7. Turn ON power to the MBC or RBC enclosure. Page 2 of 6

3 8. If you changed the operating state of any equipment, restore it to its previous state. If you use the BLN that is mentioned in the Prerequisites section, do NOT plug the connector attached to it into the Open Processor s BLN port. This is done during start-up. The Open Processor installation is now complete. Figure 4. Attaching the Open Processor to the Mounting Guides. Page3of6

4 Figure 5. Latching the Open Processor. Connecting the Open Processor to the Carrier CCN Control System Follow these steps to connect the Open Processor to the Carrier CCN Control system: 1. Notify the appropriate building personnel that you will be turning OFF power to equipment, and tell them what will be affected. 2. Follow all shutdown procedures necessary to prevent damage to any equipment or harm to any personnel. 3. Turn OFF power to the MBC or RBC enclosure. 4. Configure Black Box switch settings per Table Make cables per diagram in Figure 6. The RS-232 cable provided by Black Box can be used if cabling does not need to pass through conduit. 6. Install theblackboxesperdiagraminfigure6. See ( ). 7. Connect cables per diagram in Figure Plug in power supplies for Black Box devices. 9. Turn ON power to the MBC or RBC enclosure. 10.Start any other equipment that might have been shut down for this installation. Page 4 of 6

5 S - + FLN 1 OPEN PROCESSOR RS-485 TRUNK CABLE (MAX 4000' / m; STANDARD 24 AWG LOW CAPACITANCE) TAPE BACK SHIELD TxA TxB RxA RxB TB1 IC109A RS-232 TO RS-485 CONVERTER *STANDARD RS PIN PC PORT FEMALE. RS-232 PORT (25-PIN FEMALE)* RS-232 CABLE (MAX 50' / m) PORT A RS-232 (9-PIN FEMALE)* PORT B RS-232 (9-PIN FEMALE)* CMA02A COMMUNICATION ADAPTER *STANDARD RS PIN PC PORT FEMALE RS-232 CABLE (MAX 50' / m) RS-232 PORT (25-PIN FEMALE)* Carrier CCN DataLink *STANDARD RS PIN PC PORT FEMALE. GW0168R1 Figure 6. Connecting the Open Processor to the Carrier CCN Control System. Switch ID XW1A W8 W15 W5 W9 W17 Table 1. DCE B-C C B IC109A-R2 Switch Settings. Setting continued on next page... Page5of6

6 W16 S1 S2 S3 TB1 TB2 W2 W3 S1 S2 S3 S4 S5 S7 Switch ID Switch ID Table 1. IC109A-R2 Switch Settings. (continued) B NORMAL ON OFF Setting Place a jumper on TXA and RXA. Connect it to the (-) sign on FLN 1 of the Open Processor. Place a jumper on TXB and RXB. Connect it to the (+) sign. NORMAL Table : OFF 1 8: OFF CMA02A Switch Settings. Setting 2: ON (1, 3, 4, 5, 6, 7, 8: OFF) 2:ON(1,3,4,5,6,7,8:OFF) 2, 3, 4, 5: ON (1, 6, 7, 8: OFF) 3,4:ON(1,2,5,6,7,8:OFF) Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. Other product or company names mentioned herein may be the trademarks of their respective owners Deerfield Parkway Printed in the U.S.A. Buffalo Grove, IL Page6of6 U.S.A.