Manual No: Revision: G. Mag Probe. Assembly Manual

Transcription

1 Manual No: Revision: G Mag Probe Assembly Manual

2 Notice Veeder-Root makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Veeder-Root shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this publication. Veeder-Root reserves the right to change system options or features, or the information contained in this publication. This publication contains proprietary information which is protected by copyright. All rights reserved. No part of this publication may be photocopied, reproduced, or translated to another language without the prior written consent of Veeder-Root. DAMAGE CLAIMS / LOST EQUIPMENT Thoroughly examine all components and units as soon as they are received. If any cartons are damaged or missing, write a complete and detailed description of the damage or shortage on the face of the freight bill. The carrier's agent must verify the inspection and sign the description. Refuse only the damaged product, not the entire shipment. VEEDER-ROOT S PREFERRED CARRIER 1. Contact VR Customer Service at with the specific part numbers and quantities that were missing or received damaged. 2. Fax signed Bill of Lading (BOL) to VR Customer Service at VR will file the claim with the carrier and replace the damaged/missing product at no charge to the customer. Customer Service will work with production facility to have the replacement product shipped as soon as possible. CUSTOMER S PREFERRED CARRIER 1. It is the customer s responsibility to file a claim with their carrier. 2. Customer may submit a replacement purchase order. Customer is responsible for all charges and freight associated with replacement order. Customer Service will work with production facility to have the replacement product shipped as soon as possible. 3. If lost equipment is delivered at a later date and is not needed, VR will allow a Return to Stock without a restocking fee. 4. VR will NOT be responsible for any compensation when a customer chooses their own carrier. RETURN SHIPPING For the parts return procedure, please follow the appropriate instructions in the "General Returned Goods Policy" and "Parts Return" pages in the "Policies and Literature" section of the Veeder-Root North American Environmental Products price list. Veeder-Root All rights reserved.

3 Table of Contents Introduction Contractor Certification Requirements...1 Related Manuals...1 Mag Probe Installation Kits Standard Mag Probe Installation Kit ( XXX)...2 Low Level Mag Probe Installation Kit...2 Assembling Mag Probe Components Attaching Mag Probe Canister Spacer Rings...4 Assembling Floats onto Mag Probe Shaft...4 Attaching Cable Connector to Probe Canister...5 Figures Figure 1. Standard Mag Probe Installation Kit... 3 Figure 2. Low Level Mag Probe Installation Kit... 3 Figure 3. Installing Mag Probe Canister Spacer Rings... 4 Figure 4. Mag Probe float installation... 5 iii

4 Introduction This manual describes how to identify and assemble the components of Standard Magnetostrictive Probes - Form Number 8473 and Low Level Magnetostrictive Probes - Form Number 8493 (available selected areas only). Instructions are included for assembling floats onto the probe shaft, attaching spacer rings to the probe canister, and attaching the probe s cable to the canister. For guidelines on site preparation, instructions on installing the Mag Probe into a tank, and instructions on connecting wiring from the Mag Probe to the console, refer to the Veeder-Root Site Preparation and Installation Manual. Some of the installation kit components, such as epoxy packs, will be needed when installing the Mag Probe into the tank. Do not discard any unused parts. Contractor Certification Requirements Veeder-Root requires the following minimum training certifications for contractors who will install and setup the equipment discussed in this manual: Level 1 Contractors holding valid Level 1 Certification are approved to perform wiring and conduit routing, equipment mounting, probe and sensor installation, tank and line preparation, and line leak detector installation. Level 2/3 Contractors holding valid Level 2 or 3 Certifications are approved to perform installation checkout, startup, programming and operations training, troubleshooting and servicing for all Veeder-Root Tank Monitoring Systems, including Line Leak Detection and associated accessories. Warranty Registrations may only be submitted by selected Distributors. Related Manuals TLS-3XX Series Consoles Site Prep and Installation Manual 1

5 Mag Probe Installation Kits Standard Mag Probe Installation Kit ( XXX) Standard (8473) Mag Probes are shipped with the installation kit listed in Table 1 and shown in Figure 1. Table 1.- Standard Probe Installation Kit Contents Quantity Description Part Numbers 1 Cable X 1 2-inch* Product Float inch* Water Float X 1 4-inch* Product Float inch* Water Float X 1 Boot inch* OD Probe Canister Spacer Rings inch* OD Probe Canister Spacer Rings Cable Seal Kit (CSK) *Note: Depending on your order, this kit is shipped with either 2 or 4 floats and 3 or 4 spacer rings. Low Level Mag Probe Installation Kit Low Level (8493) Mag Probes are shipped with the installation kit listed in Table 2 and shown in Figure 2. Table 2.- Low Level Mag Probe Installation Kit Quantity Description Part Number 1 Cable, 5 feet long (standard size) inch* Product Float inch* Water Float X 1 3-inch* Product Float inch* Water Float X 1 Boot inch* OD Probe Canister Spacer Rings inch* OD Probe Canister Spacer Rings Cable Seal Kit (CSK) *Note: Depending on your order, this kit is shipped with either 2 or 4 floats and 3 or 4 spacer rings. 2

6 Mag Probe Installation Kits Low Level Mag Probe Installation Kit These two wires connect in the J-box to the two field wires from the Console Locking tabs (3) Product float Top view Probe cable connector (attaches to threaded connector on the top of probe canister) Side view 4-inch spacer ring Locking Water float (optional) 4-Inch Floats Note: your Mag Probe installation kit will contain 2-inch or 4-inch floats as per your order. Cable Boot Wire nuts Tie wrap Cord Grip Nut Bushing 1/2"-14 NPSL threads Body Note: watch orientation of bevels and tapers when assembling these cord grip components..4" Product float Epoxy sealant 1/2"-14 NPT threads Cord Grip Fitting.6" probes\pbinkit1.eps Cable Seal Kit Water float (optional) 2-Inch Floats Figure 1. Standard Mag Probe Installation Kit These two wires connect in the J-box to the two field wires from the console Tie wrap (CSK) Locking tabs (3) Product float Product float Wire nuts (CSK) Top view Probe cable connector (attaches to threaded connector on the top of probe canister) Note: your Mag Probe installation kit will contain 3-inch or 4-inch rings as per your order. Side view 3-inch spacer ring Water float (optional) Water float (optional) Cord Grip Nut Bushing 1/2"-14 NPSL threads Body 1/2"-14 NPT threads Cable Cord Grip Fitting (CSK) Note: watch orientation of bevels and tapers when assembling these cord grip components..4".6" Epoxy sealant (CSK) Locking tabs (3) Top view Side view 4-inch spacer ring 3-Inch Floats Boot Locking tabs (3) 2-Inch Floats Note: your Mag Probe installation kit will contain 2-inch or 3-inch floats as per your order. probes\pbinkit2.eps Figure 2. Low Level Mag Probe Installation Kit 3

7 Assembling Mag Probe Components Attaching Mag Probe Canister Spacer Rings 1. Open the Mag Probe shipping carton so that you have access to the probe. Also open the installation kit. 2. Following the instructions in Figure 3, install the proper spacer rings (3 or 4 ) onto the probe canister (although outwardly different, both the 3 and 4 rings are attached in the same way onto the canister). Top spacer ring (locking tabs up) Locking tab (3) Cut (3) After aligning spacer ring locking tabs over cuts, slide the ring down until its tabs rest on the bottom of the cuts. Twist spacer ring in either direction until locking tabs seat in notches. Notch (3) Up Canister Before sliding floats and boots over probe shaft, slide spacer ring over bottom of canister until locking tabs snap into groove. Bottom spacer ring (locking tabs down) Probe shaft Figure 3. Installing Mag Probe Canister Spacer Rings Assembling Floats onto Mag Probe Shaft The Product floats, Water Floats (if ordered), and Boots from Mag Probe Installation Kits are assembled on 8473/ 8493 probe shafts in the exact sequence and orientation shown in Figure 4. Note: Failure to snap the boot locking tabs into the locking indents on the probe shaft could cause the boot and float(s) to fall into the tank. Water floats must installed, if ordered, for the Mag Probe to operate correctly. Handle the Mag Probe carefully. Striking or dropping the probe will result in loss of calibration and could cause permanent damage. 4

8 Assembling Mag Probe Components Attaching Cable Connector to Probe Canister 8473 MAG PROBE FLOAT OPTIONS Up 4-Inch Floats - OR - Product float - shaft first. 2-Inch Floats Product float - shaft first. Boot tab locking indents Water float - (Optional) shaft second. Water float - (Optional) shaft second. Bottom of probe shaft Boot - Boot MAG PROBE FLOAT OPTIONS 3-Inch Floats - OR - 2-Inch Floats - OR - LPG 2-Inch Float Product float - shaft first. Product float - shaft first. Magnet down Up Boot tab locking indents Bottom of probe shaft Water float - (Optional) shaft second. Boot - Water float - (Optional) shaft second. Boot - Boot - probes\comboflt.eps Figure 4. Mag Probe float installation Attaching Cable Connector to Probe Canister Attach the connector end of the Mag Probe cable to the threaded connector on top of the probe canister and tighten down the integral nut. This completes the Mag Probe assembly. Save the remaining kit components. They will be needed to install the Mag Probe into the tank (reference the console Site Prep and Installation manual). 5

9 For technical support, sales or other assistance, please visit: