Installation Instructions

Transcription

1 Installation Instructions Double Serial Interface it (for EasyCoder PF2i, PF4i, PF4ci, PM4i, PX4i and PX6i)

2 Intermec Technologies Corporation Corporate Headquarters th ve. W. Everett, W U.S.. The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and service Intermecmanufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec. Information and specifications contained in this document are subject to change without prior notice and do not represent a commitment on the part of Intermec Technologies Corporation by Intermec Technologies Corporation. ll rights reserved. The word Intermec, the Intermec logo, Norand, rcitech, Crossar, Data Collection rowser, dcrowser, Duratherm, EasyCoder, EasyLN, Enterprise Wireless LN, EZuilder, Fingerprint, i-gistics, I (under license), InterDriver, Intermec Printer Network Manager, IRL, JNUS, LabelShop, Mobile Framework, MobileLN, Nor*Ware, Pen*ey, Precision Print, PrintSet, RoutePower, TE 2000, Trakker ntares, UP, Universal ccess Point, and Virtual Wedge are either trademarks or registered trademarks of Intermec Technologies Corporation. Throughout this manual, trademarked names may be used. Rather than put a trademark ( or ) symbol in every occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and to the benefit of the trademark owner, with no intention of infringement. There are U.S. and foreign patents pending. Torx is a registered trademark of Camcar Division of Textron Inc.

3 Contents Contents 1 Introduction Description... 2 Printer Firmware...2 Installation it Physical Installation EasyCoder PF2/4i printers...4 EasyCoder PM4i printers...9 EasyCoder PX4/6i printers...15 Serial Interface "uart2:" and "uart4:" RS-232 Non-isolated...20 RS-422 Isolated, Full duplex...22 RS-485 Isolated, Half duplex...24 Serial Interface "uart3:" and "uart5:" RS-232 Non-isolated...28 RS-422 Non-isolated, Full duplex m Current Loop...32 Double Serial Interface it Installation Instructions iii

4 Contents iv Double Serial Interface it Installation Instructions

5 1 Introduction This chapter describes the Double Serial Interface it for EasyCoder PF2/4i-, PM4i-, and PX4/6i-series printers. Double Serial Interface it Installation Instructions 1

6 Chapter 1 Introduction Description This Installation Instructions booklet describes how to install a Double Serial interface board in an EasyCoder PF2i, PF4i, PF4i Compact Industrial, PM4i, PX4i, or PX6i printer. The installation instructions describes how to physically install the interface board in a printer and how to configure the two serial communication ports. This interface kit must only be physically installed by an authorized service technician. Intermec assumes no responsibility for personal injury or damage to the equipment if the installation in performed by an unauthorized person. Printer Firmware The printer must be fitted with Intermec Fingerprint v8.00 (or later). For some combinations of two interface boards in EasyCoder PM4i and PX4/6i printers, Fingerprint v8.30 (or later) is required. This kit does not work with IPL. In Intermec Fingerprint, the serial ports are addressed as "uart2:", "uart3:", "uart4:", and "uart5:" (communication channel #2, #3, #7, and #8 respectively). Installation it The Double Serial Interface it contains: One Double Serial interface board fitted with circuits and straps for RS-232 non-isolated. One hexagonal spacer (only used for two interface boards fitted in a PM4i or PX4/6i printer) Two flat cables This Installation Instruction booklet The only tools required for the installation are #T10 and #T20 Torx screwdrivers plus a small wrench. 2 Double Serial Interface it Installation Instructions

7 2 Physical Installation This chapter describes how to physically install the Double Serial Interface it in an EasyCoder PF2/4i-, PM4i-, or PX4/6i-series printer. Take precautions against electrostatic discharges, for example by wearing grounded bracelets. Double Serial Interface it Installation Instructions 3

8 Chapter 2 Physical Installation EasyCoder PF2/4i Printers Switch off the printer and disconnect the power cord. Disconnect all communication cables. Remove the front/left-hand cover as follows. The electronic compartment contains wires and components with dangerous voltage (up to 380V). Make sure that the printer is switched off and the power cord is disconnected before the left-hand cover is removed. Open the right-hand door. Using a #T20 Torx screwdriver, remove the three screws and lift the cover up so it disengages the bottom plate. Swing out the rear part of the cover so you can disconnect the console cable from the CPU board. Put the cover aside on a soft cloth or similar to avoid scratches. 4 Double Serial Interface it Installation Instructions

9 Chapter 2 Physical Installation Remove the two #T10 Torx screws that hold the interface cover plate. Remove the cover plate. #T10 Torx screw Cover plate #T10 Torx screw Save the cover plate for possible later use. eep the screws. Remove the #T20 Torx screw fitted on the hexagonal spacer at the CPU board. eep the screw. If reconfiguration of the interface board is required, fit or remove circuits and straps according to the descriptions in Chapters 3 and 4. ttach the flat cable included in the kit to connector J62 (marked EXP ORD ) on the CPU board (see page 7). Double Serial Interface it Installation Instructions 5

10 Chapter 2 Physical Installation Insert the interface board with the component side facing right, as seen from behind. Component side #T10 Torx screw Interface board #T10 Torx screw ttach the interface board to the printer s rear plate using the two screws left over when you removed the original cover plate. Using the #T20 Torx screw you previously removed, attach the interface board to the hexagonal spacer on the CPU board. The kit contains two flat cables. Connect the flat cable with two connectors to P1 on the interface board, see the next page. 6 Double Serial Interface it Installation Instructions

11 R15 C54 R14 R13 R12 R30 R25 R26 C64 R27 C63 C62 R28 R29 C55 R8 R18 R10 C56 R9 C57 C33 R11 C61 C36 C35 R7 J61 R4 R20 C30 R24 C53 R23 C40 R3 C60 C51 C52 C42 C31 URT J6 F13 J10 J7 C J8 F9 J9 R19 R32 P3 RS232: IC21, J6 RS422: IC22, J6, J7, J8 20MCL: IC23, IC24, J5 J9*, J10* *: TRNSM.=J9, RECEIV.=J10 PSSIVE=, CTIVE=+C C P01 C10 C12 R21 R22 IC7 IC8 J5 RS232: IC11, J2 RS422: IC12, J3, J4 RS485: IC13, J1, J4* *: IF END OF CLE P35 P1 J62 URT IC6 C50 IC5 IC1 IC4 R6 C41 C34 C32 R5 R2 R1 Chapter 2 Physical Installation F14 F10 F15 F11 F16 F12 R31 R35 Z1 Z2 R33 R34 IC23 IC24 IC22 C11 C13 D1 IC21 IC20 C4 C3 IC3 IC10 IC2 P1 F2 F7 F3 F8 F4 F5 J3 J4 J2 R17 R16 C2 C1 IC11 IC13 IC12 F1 F6 IC9 P2 J1 EXP ORD Cable Hexagonal spacer The flat cable should run as illustrated below. Double Serial Interface it Installation Instructions 7

12 Chapter 2 Physical Installation Connect the console cable to J50 on the CPU board and put back the cover over the electronics compartment. Take care so the console cable runs above the ribbon motor (if any) and does not become entangled in the headlift mechanism. Connect the communication cables to the connectors on the printer s rear plate. Connect the power cord and switch on the power. Enter the Setup Mode to set the proper communication parameters for the serial communication channels "uart2:" and "uart3:". Serial interface socket "uart3:" Serial interface socket "uart2:" 8 Double Serial Interface it Installation Instructions

13 EasyCoder PM4i Printers Chapter 2 Physical Installation Switch off the printer and disconnect the power cord. Disconnect all communication cables. Turn the printer over so it rests on its left-hand cover. Use a soft cloth or similar to avoid scratches. Open the right-hand door. Using a #T20 Torx screwdriver, remove the four screws that hold the cover along the lower left edge of the bottom plate and the four screws that hold the cover to the center section. Put the printer back on its feet and remove the cover while disconnecting the console cable from the CPU board. The electronic compartment contains wires and components with dangerous voltage (up to 380V). Make sure that the printer is switched off and the power cord is disconnected before the cover is removed. Put the cover aside taking care to avoid scratches. Double Serial Interface it Installation Instructions 9

14 Chapter 2 Physical Installation Remove the two #T10 Torx screws that hold the cover plate. lways start with the inner one. Remove the cover plate. #T10 Torx screw Cover plate #T10 Torx screw Save the cover plate for possible later use. eep the screws. Remove the #T20 Torx screw fitted on the hexagonal spacer at the center of the CPU board. eep the screw. If reconfiguration of the interface board is required, fit or remove circuits and straps according to the descriptions in Chapters 3 and 4. ttach the flat cable included in the kit to connector J62 (marked EXP ORD ) on the CPU board (see illustration on page 12). 10 Double Serial Interface it Installation Instructions

15 Chapter 2 Physical Installation Insert the interface board with the component side facing right, as seen from behind. Component side #T10 Torx screw Interface board #T10 Torx screw ttach the interface board to the printer s rear plate using the two screws left over when you removed the original cover plate. Using the #T20 Torx screw you previously removed, attach the interface board to the hexagonal spacer on the CPU board (see next page). If you are installing an interface board in the outer slot, you need to remove the screw that holds the inner board and replace it with the spacer included in the kit. The secure the outer board to the spacer with the screw (see illustration on the next two pages). The kit contains two flat cables, one with two connectors for use with a single interface board and one with three connectors for use with double interface boards. Connect the appropriate flat cable to connector P1 on the interface board, also see the next two pages. Double Serial Interface it Installation Instructions 11

16 R15 C54 R14 R13 R12 R30 R25 R26 C64 R27 C63 C62 R28 R29 C55 R8 R18 R10 C56 R9 C57 C33 R11 C61 C36 C35 R7 J61 R4 R20 C30 R24 C53 R23 C40 R3 C60 C51 C52 C42 C31 URT J6 F13 J10 J7 C J8 F9 J9 R19 R32 P3 RS232: IC21, J6 RS422: IC22, J6, J7, J8 20MCL: IC23, IC24, J5 J9*, J10* *: TRNSM.=J9, RECEIV.=J10 PSSIVE=, CTIVE=+C C P01 C10 C12 R21 R22 IC7 IC8 J5 RS232: IC11, J2 RS422: IC12, J3, J4 RS485: IC13, J1, J4* *: IF END OF CLE P35 P1 J62 URT IC6 C50 IC5 IC1 IC4 R6 C41 C34 C32 R5 R2 R1 Chapter 2 Physical Installation F14 F10 F15 F11 F16 F12 R31 R35 Z1 Z2 R33 R34 IC23 IC24 IC22 C11 C13 D1 IC21 IC20 C4 C3 IC3 IC10 IC2 P1 F2 F7 F3 F8 F4 F5 J3 J4 J2 R17 R16 C2 C1 IC11 IC13 IC12 F1 F6 IC9 P2 J1 EXP ORD Cable Hexagonal spacer In case of a single interface board, the flat cable should run as illustrated below. 12 Double Serial Interface it Installation Instructions

17 Chapter 2 Physical Installation In case of two interface boards, the flat cable should run as illustrated below. Put back the cover over the electronics compartment. Connect the console cable to J50 on the CPU board and put back the cover over the electronics compartment. Take care so the console cable runs above the ribbon motor and does not become entangled in the headlift mechanism. Connect the power cord and switch on the power. Enter the Setup Mode to set the proper communication parameters for new the serial communication ports. Double Serial Interface it Installation Instructions 13

18 Chapter 2 Physical Installation llowed interface combinations (Fingerprint v8.30 or later) Left-hand slot Ports Right-hand slot Ports Double Serial uart2: + uart3: Double Serial uart2: + uart3: Double Serial uart4: + uart5: Double Serial uart2: + uart3: Serial/Industrial uart4: Double Serial uart2: + uart3: IEEE 1284 centronics: Serial/Industrial uart2: Serial/Industrial uart2: Serial/Industrial uart3: Serial/Industrial uart2: Double Serial uart3: + uart4: Serial/Industrial uart2: IEEE 1284 centronics: IEEE 1284 centronics: IEEE 1284 centronics: Double Serial uart2: + uart3: IEEE 1284 centronics: Serial/Industrial uart2: Remarks: The left-hand slot is the slot closest to the center section. lways start by fitting an interface board in the left-hand slot. RS-485 is only supported by "uart2:" "uart3:" "uart5:" "uart2:" "uart4:" Example of EasyCoder PM4i with two double serial interface boards. 14 Double Serial Interface it Installation Instructions

19 EasyCoder PX4i and PX6i Printers Chapter 2 Physical Installation Switch off the power and disconnect the power cord. Disconnect all communication cables. Open the right-hand door. Remove the eight #T10 Torx screws that hold the left-hand cover. Put the cover aside on a soft cloth or similar to avoid scratches. The electronics compartment contains high voltage components and wires. Do not open the electronics compartment before the printer is safely disconnected from any C supply. Remove the one or two cover plates depending on how many interface boards you are going to install. Each plate is held by two #T10 Torx screws. lways start installation at the innermost position. Inner cover plate Outer cover plate Double Serial Interface it Installation Instructions 15

20 Chapter 2 Physical Installation Save the cover plate(s) for possible later use. eep the screws. Remove the #T20 Torx screw fitted on the hexagonal spacer at the center of the CPU board. eep the screw. If necessary, reconfigure the interface board by fitting or removing circuits and straps according to the descriptions of each board later in this chapter. ttach the flat cable included in the kit to connector J62 (marked EXP ORD ) on the CPU board (see illustration on the next page). Insert the interface board with the component side facing right, as seen from behind. Existing spacer Spacer (only in case of two boards) #T10 Torx screw (2 + 2) Interface boards #T20 Torx screw Connect to J62 Illustration shows installation of one IEEE 1284 and one Double Serial interface board. Installation of one board: ttach the interface board in the innermost slot in the printer s rear plate using the two screws left over when you removed the original cover plate. Using the #T20 Torx screw you previously removed, attach the interface board to the hexagonal spacer at the center of the CPU board. 16 Double Serial Interface it Installation Instructions

21 Chapter 2 Physical Installation Installations of two boards: First install the inner board, then the outer one. Put the hexagonal spacer included in the kit between the inner and the outer interface board, and finally secure the outer board with the screw. The kit contains two flat cables, one with two connectors for use with a single interface board and one with three connectors for use with double interface boards. Connect the appropriate flat cable to connector P1 on the interface board, as illustrated below. The flat cable should run as illustrated below. Put back the cover over the electronics compartment. Connect the communication cables to the connectors on the printer s rear plate. Double Serial Interface it Installation Instructions 17

22 Chapter 2 Physical Installation Connect the power cord and switch on the power. In case the interface board provides additional serial communication ports, enter the Setup Mode to set the proper communication parameters for these ports. llowed interface combinations (Fingerprint v8.30 or later) Left-hand slot Ports Right-hand slot Ports Double Serial uart2: + uart3: Double Serial uart2: + uart3: Double Serial uart4: + uart5: Double Serial uart2: + uart3: Serial/Industrial uart4: Double Serial uart2: + uart3: IEEE 1284 centronics: Serial/Industrial uart2: Serial/Industrial uart2: Serial/Industrial uart3: Serial/Industrial uart2: Double Serial uart3: + uart4: Serial/Industrial uart2: IEEE 1284 centronics: IEEE 1284 centronics: IEEE 1284 centronics: Double Serial uart2: + uart3: IEEE 1284 centronics: Serial/Industrial uart2: Remarks: The left-hand slot is the slot closest to the center section. lways start by fitting an interface board in the left-hand slot. RS-485 is only supported by "uart2:" "uart3:" "uart5:" "uart2:" "uart4:" 18 Double Serial Interface it Installation Instructions

23 3 Serial Interface "uart2:", "uart3:", and "uart4:" This chapter describes how to modify the interface board for RS-232 non-isolated (standard), RS-422 isolated/full duplex, or RS-485 isolated/half duplex on the "uart2:", "uart3:", or "uart4:" port and explains the configuration of the interface connector. The connector is marked URT on the interface board. When fitting driver circuit and straps before installing the interface board, make sure that the circuit is not fitted upside down (see front end markings in the illustrations). lso make sure that the legs of the circuit fit into the slots in the socket and are not bent. Take ample precautions to protect the board and circuits from electrostatic discharges. Double Serial Interface it Installation Instructions 19

24 R15 C54 R14 R13 R12 R30 R25 R26 C64 R27 C63 C62 R28 R29 R8 R18 R10 C56 R9 C57 C36 C35 R7 R4 R3 R6 C34 R5 R2 C51 R1 C42 Chapter 3 Serial Interfaces "uart2:", "uart3:", and "uart4:" RS-232 Non-isolated (standard) URT P3 F13 F14 F10 F15 F11 F16 F12 F9 J6 J10 J7 C J8 R32 RS232: IC21, J6 RS422: IC22, J6, J7, J8 20MCL: IC23, IC24, J5 J9*, J10* *: TRNSM.=J9, RECEIV.=J10 PSSIVE=, CTIVE=+C R31 C J9 R35 R19 Z2 Z1 R34 R33 IC23 IC24 IC22 C11 C13 D1 IC21 C10 C P01 C61 R20 R24 R21 R22 R23 C40 IC7 C60 IC8 J5 IC20 C41 RS232: IC11, J2 RS422: IC12, J3, J4 RS485: IC13, J1, J4* *: IF END OF CLE C4 C3 IC3 C33 IC10 IC2 P1 Strap fitted on J2 URT F2 F7 F3 F8 F4 F5 J2 J3 J4 R17 R16 C2 IC11 C1 IC13 IC12 IC6 C53 C32 C31 IC4 C50 RS-232 circuit fitted on IC11 P2 F1 F6 IC9 C55 R11 IC5 C30 J1 IC1 C52 20 Double Serial Interface it Installation Instructions

25 Chapter 3 Serial Interface "uart2:", "uart3:", and "uart4:" Connector Configuration (RS-232 on "uart2:", "uart3:", or "uart4:") D-9 socket Signal Meaning 1 External +5VDC max 500 m (automatic switchoff at overload, short-circuit protected) 2 TXD Transmit data 3 RXD Receive data 4 DSR Data set ready 5 GND Ground 6 DTR Data terminal ready 7 CTS Clear to send 8 RTS Request to send 9 Not used RTS CTS DTR GND DSR RXD TXD +5V (0.5 RS-232 socket as seen from the outside. Double Serial Interface it Installation Instructions 21

26 R15 C54 R14 R13 R12 R30 R25 R26 C64 R27 C63 C62 R28 R29 R8 R18 R10 C56 R9 C57 C36 C35 R7 R4 R3 R6 C34 R5 R2 C51 R1 C42 Chapter 3 Serial Interfaces "uart2:", "uart3:", and "uart4:" RS-422 Isolated, Full Duplex (reconfiguration required) URT P3 F13 F14 F10 F15 F11 F16 F12 F9 J6 J10 R35 J7 C RS232: IC21, J6 RS422: IC22, J6, J7, J8 20MCL: IC23, IC24, J5 J9*, J10* *: TRNSM.=J9, RECEIV.=J10 PSSIVE=, CTIVE=+C C IC21 C10 C12 C61 R20 R24 R21 R22 R23 C40 IC7 C60 IC8 J5 Remove strap on J2 RS232: IC11, J2 RS422: IC12, J3, J4 RS485: IC13, J1, J4* *: IF END OF CLE P1 Fit straps on J3 and J4 URT C32 C31 IC4 C50 C52 IC20 IC6 IC5 IC1 J8 R32 R31 J9 C41 C33 IC10 IC2 C53 C30 R19 Z2 Z1 R34 R33 IC23 IC24 IC22 C11 C13 D P01 C4 C3 IC3 F2 F7 F3 F8 F4 F5 J3 J4 J2 R17 R16 C2 IC11 C1 IC13 IC12 F1 F6 IC9 C55 P2 R11 J1 Remove RS-232 circuit on IC11 Fit RS-422 circuit on IC12 The RS-422 circuit is available as a spare part, see the Spare Parts Catalog. 22 Double Serial Interface it Installation Instructions

27 Chapter 3 Serial Interface "uart2:", "uart3:", and "uart4:" Connector Configuration (RS-422 Isolated on "uart2:", "uart3:", or "uart4:") D-9 socket Signal Meaning 1 External +5VDC max 500 m (automatic switchoff at overload, short-circuit protected) provided strap is fitted on J2: which spoils the galvanical isolation 2 +TXD +Transmit data 3 +RXD +Receive data 4 5 GNDE Ground 6-7 -RXD -Receive data 8 -TXD -Transmit data 9 -TXD -RXD GNDE +RXD +TXD +5V (0.5 ) if GND strap fitted RS-422 socket as seen from the outside. Double Serial Interface it Installation Instructions 23

28 R15 C54 R14 R13 R12 R30 R25 R26 C64 R27 C63 C62 R28 R29 R8 R18 R10 C56 R9 C57 C36 C35 R7 R4 R3 R6 C34 R5 R2 C51 R1 C42 Chapter 3 Serial Interfaces "uart2:", "uart3:", and "uart4:" RS-485 Isolated, Half Duplex (reconfiguration required) Remove strap on J2 URT P3 F13 F14 F10 F15 F11 F16 F12 F9 J6 J10 J7 C J8 R32 RS232: IC21, J6 RS422: IC22, J6, J7, J8 20MCL: IC23, IC24, J5 J9*, J10* *: TRNSM.=J9, RECEIV.=J10 PSSIVE=, CTIVE=+C R31 C J9 R35 R19 Z2 Z1 R34 R33 IC23 IC24 IC22 C11 C13 D1 IC21 C10 C P01 C61 R20 R24 R21 R22 R23 C40 IC7 C60 IC8 J5 IC20 C41 Remove RS-232 circuit on IC11 Fit RS-485 driver circuit on IC13 Fit strap on J4 if end of cable (terminator) RS232: IC11, J2 RS422: IC12, J3, J4 RS485: IC13, J1, J4* *: IF END OF CLE URT P2 F2 F7 F3 F8 F4 F5 F1 F6 J3 J4 J2 IC9 R17 R16 C4 C2 IC3 C3 C1 IC13 IC11 IC12 C55 C33 R11 C30 IC5 IC6 C53 J1 IC10 IC2 C32 C50 C52 IC1 C31 IC4 P1 Fit strap on J1 The RS-485 circuit is available as a spare part, see the Spare Parts Catalog. 24 Double Serial Interface it Installation Instructions

29 Chapter 3 Serial Interface "uart2:", "uart3:", and "uart4:" Connector Configuration (RS-485 Isolated on "uart2:" only) D-9 socket Signal Meaning 1 External +5VDC max 500 m (automatic switchoff at overload, short-circuit protected) provided strap is fitted on J2: which spoils the galvanical isolation 2 +DT GNDE Ground DT 9 -DT GNDE +DT +5V (0.5 ) if GND strap fitted RS-422 socket as seen from the outside. Note: The increased use of LN networks has made the RS- 485 interface somewhat obsolete, because RS-485 requires a special communication protocol and a dedicated wiring system limited to 1,200 m (4,000 ft). We only recommend RS-485 for existing applications and advice the customer to consider a LN network solution for new applications. Double Serial Interface it Installation Instructions 25

30 Chapter 3 Serial Interfaces "uart2:", "uart3:", and "uart4:" 26 Double Serial Interface it Installation Instructions

31 4 Serial Interface "uart3:", "uart4:", and "uart5:" This chapter describes how to modify the interface board for RS-232 non-isolated (standard), RS-422 non-isolated/full duplex, or 20 m current loop on the "uart3:", "uart4:", and "uart5:" port and explains the configuration of the interface connector. The connector is marked URT on the interface board. When fitting driver circuit and straps before installing the interface board, make sure that the circuit is not fitted upside down (see front end markings in the illustrations). lso make sure that the legs of the circuit fit into the slots in the socket and are not bent. Take ample precautions to protect the board and circuits from electrostatic discharges. Double Serial Interface it Installation Instructions 27

32 R15 C54 R14 R13 R12 R30 R25 R26 C64 R27 C63 C62 R28 R29 R8 R18 R10 C56 R9 C57 C36 C35 R7 R4 R3 R6 C34 R5 R2 C51 R1 C42 Chapter 4 Serial Interface "uart3:", "uart4:", and "uart5:" RS-232 Non-isolated (standard) Strap fitted on J6 RS-232 circuit fitted on IC21 URT P3 F13 F14 F10 F15 F11 F16 F12 F9 J6 J10 J7 C J8 R32 RS232: IC21, J6 RS422: IC22, J6, J7, J8 20MCL: IC23, IC24, J5 J9*, J10* *: TRNSM.=J9, RECEIV.=J10 PSSIVE=, CTIVE=+C C IC21 C10 C12 RS232: IC11, J2 RS422: IC12, J3, J4 RS485: IC13, J1, J4* *: IF END OF CLE P1 URT J2 C32 C31 IC4 C50 C52 C61 R20 R24 R21 R22 R23 C40 IC7 C60 IC8 J5 IC20 IC6 IC5 IC1 R31 J9 R35 R19 C41 C33 IC10 IC2 C53 C30 Z2 Z1 R34 R33 IC23 IC24 IC22 C11 C13 D P01 C4 C3 IC3 F2 F7 F3 F8 F4 F5 J3 J4 R17 R16 C2 IC11 C1 IC13 IC12 F1 F6 IC9 P2 C55 R11 J1 28 Double Serial Interface it Installation Instructions

33 Chapter 4 Serial Interface "uart3:", "uart4:", and "uart5:" Connector Configuration (RS-232 on "uart3:", "uart4:", or "uart5:") D-9 socket Signal Meaning 1 External +5VDC max 500 m (automatic switchoff at overload, short-circuit protected) 2 TXD Transmit data 3 RXD Receive data 4 DSR Data set ready 5 GND Ground 6 DTR Data terminal ready 7 CTS Clear to send 8 RTS Request to send 9 Not used RTS CTS DTR GND DSR RXD TXD +5V (0.5 RS-232 socket as seen from the outside. Double Serial Interface it Installation Instructions 29

34 R15 C54 R14 R13 R12 R30 R25 R26 C64 R27 C63 C62 R28 R29 R8 R18 R10 C56 R9 C57 C36 C35 R7 R4 R3 R6 C34 R5 R2 C51 R1 C42 Chapter 4 Serial Interface "uart3:", "uart4:", and "uart5:" RS-422 Non-isolated, Full Duplex (reconfiguration required) Move strap from J6 to J6 Fit straps on J7 and J8 Fit RS-422 circuit on IC22 Remove RS-232 circuit from IC21 URT P3 F13 F14 F10 F15 F11 F16 F12 F9 J6 J10 J7 C J8 R32 RS232: IC21, J6 RS422: IC22, J6, J7, J8 20MCL: IC23, IC24, J5 J9*, J10* *: TRNSM.=J9, RECEIV.=J10 PSSIVE=, CTIVE=+C RS232: IC11, J2 RS422: IC12, J3, J4 RS485: IC13, J1, J4* *: IF END OF CLE C IC21 C10 C12 C61 R20 R24 R21 R22 R23 C40 IC7 C60 IC8 J5 P1 URT J2 C32 C31 IC4 C50 C52 IC20 IC10 IC6 IC5 IC1 R31 J9 R35 R19 Z2 C33 IC2 C41 C30 C53 Z1 C4 R34 R33 IC23 IC24 C3 IC22 C11 C13 D1 IC P01 F2 F7 F3 F8 F4 F5 J3 J4 R17 R16 C2 IC11 C1 IC13 IC12 F1 F6 IC9 P2 C55 R11 J1 The RS-422 circuit is available as a spare part, see the Spare Parts Catalog. 30 Double Serial Interface it Installation Instructions

35 Chapter 4 Serial Interface "uart3:", "uart4:", and "uart5:" Connector Configuration (RS-422 Non-isolated on "uart3:", "uart4:", or "uart5:") D-9 socket Signal Meaning 1 External +5VDC max 500 m (automatic switch-off at overload, short-circuit protected) provided strap is moved from J6 to J6 2 +TXD +Transmit data 3 +RXD +Receive data 4 5 GNDE Ground 6-7 -RXD -Receive data 8 -TXD -Transmit data 9 -TXD -RXD GND +RXD +TXD +5V (0.5 ) RS-422 socket as seen from the outside. Double Serial Interface it Installation Instructions 31

36 R15 C54 R14 R13 R12 R30 R25 R26 C64 R27 C63 C62 R28 R29 R8 R18 R10 C56 R9 C57 C36 C35 R7 R4 R3 R6 C34 R5 R2 C51 R1 C42 Chapter 4 Serial Interface "uart3:", "uart4:", and "uart5:" 20 m Current Loop (reconfiguration required) Remove strap from J6 Fit strap on J10 if printer is receiver: +C = active = passive Fit strap on J9 if printer is transmitter: +C = active = passive URT P3 F13 F14 F10 F15 F11 F16 F12 F9 J6 J10 J7 C J8 R32 RS232: IC21, J6 RS422: IC22, J6, J7, J8 20MCL: IC23, IC24, J5 J9*, J10* *: TRNSM.=J9, RECEIV.=J10 PSSIVE=, CTIVE=+C RS232: IC11, J2 RS422: IC12, J3, J4 RS485: IC13, J1, J4* *: IF END OF CLE R31 C J9 R35 R19 IC21 C10 C12 P1 URT J2 C50 IC1 C31 IC4 C52 Z2 C33 C61 R20 R24 R21 R22 R23 C40 IC7 C60 IC8 J5 IC20 IC10 IC2 C41 IC6 C53 IC5 C30 C32 Z1 C4 R34 R33 IC23 IC24 IC22 C11 C13 D1 IC3 C P01 Fit optocouplers on IC23 and IC24 Remove RS-232 circuit from IC21 F2 F7 F3 F8 F4 F5 F1 F6 J3 J4 IC9 R17 R16 C2 IC11 C1 IC13 IC12 P2 C55 R11 J1 Fit strap on J5 The optocouplers are available as spare parts, see the Spare Parts Catalog. 32 Double Serial Interface it Installation Instructions

37 Chapter 4 Serial Interface "uart3:", "uart4:", and "uart5:" Connector Configuration (20 m Current Loop on "uart3:", "uart4:", or "uart5:") D-9 socket Signal Meaning 1 External +5VDC max 500 m (automatic switchoff at overload, short-circuit protected) provided a strap is fitted on J6 which spoils the galvanic isolation 2 +TXD +Transmit data 3 +RXD +Receive data 4 5 GNDE Ground 6-7 -RXD -Receive data 8 -TXD -Transmit data 9 MTG -TXD -RXD RXD +TXD +5V DC if GND strap fitted MTG 20 m Current Loop socket as seen from the outside. Note: Maximum recommended baud rate is 9600 bps. Double Serial Interface it Installation Instructions 33

38 Chapter 4 Serial Interface "uart3:", "uart4:", and "uart5:" 34 Double Serial Interface it Installation Instructions

39

40 Intermec Technologies Corporation Corporate Headquarters th venue West Everett, W tel fax Double Serial Interface it Installation Instructions * * * *