SY210NT V5. Networking Muti-Doors Controller Installation Manual V0110

Transcription

1 SY210NT V5 Networking Muti-s Installation Manual V0110 WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. SYRIS Technology Corp. 21F-2, NO.12, Sec1, Taijunggang Rd, Taichung, Taiwan (403) Tel: Fax:

2 SECTION 1: INTRODUCTION TO SY210NT V PRODUCT OVERVIEW ABOUT THIS MANUAL New in this Version Fast Setting Index Sheet and Card Record Sheet FEATURES SPECIFICATIONS...4 SECTION 2: SY210NT WIRE & QUICK INSTALLING REQUIRED EQUIPMT SELECTING A MOUNTING LOCATION TYPICAL MOUNTING DIAGRAM INSTALLING SY210NT INSTALLING THE READER WIRING DIAGRAM5 2.6 CONNECTING DOOR LOCK WIRING DIAGRAM CONNECTING BUTTON TO DOOR OP CONNECTING THE DOOR DETECTION CONNECTING POWER SUPPLY...5 SECTION 3: SY210NT V5 SETTING INTRODUCTION SETTING MU LOGIN SETTING MU LOGOUT SHOW VERSION SY210NT FACTORY DEFAULTS...6 SECTION 4: SY210NT V5 SETTINGS SYSTEM FUNCTIONS Functions Module System Utility CARD MANAGEMT Add Card Edit Card Delete Card Show Card All Card APB Setting FINGERPRINT MANAGEMT Add Fingerprint Delete Fingerprint Delete All Fingerprint... 7 SECTION 5: SET UP SY210NT V5 STEP BY STEP CONTROLLER FUNCTION Set ID Same Card Time Invalid Lock Baud Rate Setting DI Setting Elevator Mode Set Max Card READER MODULE SETTING Module Auto Detect Reader Module ID Setting MDWIE-2 ID Setting DOOR FUNCTION SETTING Relay Push Button APB Setting MASTER CARD FUNCTION SETTING PIN Setting Add Card Delete Card SYSTEM UTILITY Date Setting Time Setting System Reboot Data Backup / Restore System Initial CARD MANAGEMT Add Card Add Card By Serial Add Card By No Edit Card Card Condition Setting (Valid / Invalid) Card PIN Setting Card APB Setting

3 Single Card Delete Delete All Card Cards Browse All Card APB Setting FINGERPRINT MANAGEMT Add Fingerprint Delete Fingerprint Delete All Fingerprint RESETTING THE SY210NT UNIT TO FACTORY DEFAULTS...10 APPDIX 1:QUICK REFERCE PROGRAMMING TABLE 11 APPDIX 2:PROGRAMMING WORKSHEET...12 APPDIX 3:CARD INFORMATION RECORD SHEET13 APPDIX 4: SY210NT V5 CARD CAPACITY AND I/O DATA LIST 14 APPDIX 5:USING THE SY210NT SYSTEM...15 Q1: How to setting reader ID? What Reader ID and are relate?...15 Q2: How to add the card?...16 Q3: How to setting the push button from controller? 16 Q4: How to Connect HID Readers of Wiegand interface with?...17 Q5: How to use MDDIDO Module Connecting the Exit Detector or Exit Button?...18 APPDIX 6: GERAL WIRING DIAGRAM

4 Section 1: Introduction to SY210NT V5 MDNET-1 Module The functions are same as MDNET Product Overview 4. Printer Module Networking Multi-s can control 4 doors, link 8 card readers (4 IN, 4 can connect to the following printers directly or reports printing via OUT), use 63,000 cards and 210,000 I/O data record at most. (Reference printer module. appendix 4) 1. Impact Printers 2. Ink Jet Printer 3. Laser Printers SY210NT V5 Network Multi-s provides perfect functions and stable & reliable quality. * The controller can supply 63,000 people to use at most. * Single controller can manage 4 doors In/Out at the same time. * Regional Anti-Pass Back (APB) function will be activated without PC on-line. * The local APB will be activated in LAN. * The motherboard produced by the SMD technology. The quality is stable and reliable. Easy Setting All setting can be set by using controller keypad and LCD monitor(16x2 Char). You can make choice of purchase of expansion module that divides into two types: internal and external. Internal module of controller include: 1. MDNET-2 Ethernet Converter Ethernet Communication Converter used to convert RS485 series signal Fast Setting Index Sheet and Card Record Sheet into TCP/IP package. According to different network application types, the User can find out a setting location by referring the Quick Reference Programming module provides two types:server mode & Client mode. Table, appendix 1. The module will wait for the signal from network and it will send decode User can print and record Card Information by using appendix 3.. signal to HOST CPU through series communication port under Server mode. The module will re-package the signal and resend on network while MDDIDO Module divides MDDIDO-16 channel (16 voltage free input, 16 relay output) and MDDIDO-1S 2 channel (4 voltage free input, 2 relay output). System extendibility:user can use MIDDO module expansion of system when first program insufficient for user need; MDDIDO Module is easy to expansion; e.g. Add controller, Readers or DIDO Modules etc. 3. MDWIE-1 (Wigand Module install inside of the ) MDWIE-1 Wigand Module has 2 S/N. Each number represents a channel, is similar to RS485 Reader; First W26Reader use first Serial NO. Reader ID setting( ID=1, Firs door; ID=2;Second door..). When expand the MDWIE-1 Module to transform the RS485 interface into the Wiegand interface, user can connect with each kind of devices of Wiegand interface About this Manual This Installation Manual provides installation and setting instructions for SY210NT V5. Please read this manual carefully before installing or setting the SY210NT New in this Version The subject matters of the manual are focus on update of SY210NT V5: 1.Increase the number of user:the number of user can up to 63,000. I/O records can up to 21,000. (Reference appendix 4) 2.The time of door open by hand is longer:the time can be set as 9999 seconds or above. 3.Backup SD Card:The types of backup are Manual /Automatic. The backup / restore set can up to 10 sets. 4. Invalid password entering event handle:user can set times or lock time while error password input (1~999 sec). 1.3 Features received reply from the CPU HOST. And then the command cycle will be 1. Internal extension Module optional: done. User can add MDNET-2 network module to expand network function interface. (a) (b) 10/100M Ethernet Converter(MDNET-2). 4CH Wigand Signal Input Module(MDWIE-2). (c) SD Card module (MDSD-2 applies SD Card whose memory size of 2. MDPOE-1 Ethernet Power supplier module (Power over 256MB 512MB 1GB). Ethernet) (d) POE Power over Ethernet Module (MDPOE-1,Client). Power over Ethernet is called PoE that is the technology about power 2. The controller can be run with the software: SYW95A-V V2 V3 SYW95A supply. PoE can transmit electrical power over standard twisted-pair cable in -V2-NET and SY-SOFT-95A. an Ethernet network. We can supply power from HUB by using this 3. User can adjust the number of cards and record capacity of I/O data according to technology without connect other power source. need. 3. MDWIE-2 (Wiegand Signal Input Module) After installing 4 CH Wigand signal input module (MDWIE-2), user can connect four readers that include reader fingerprint etc. All devices as mention have Wiegand interface. 4. Promote number of User/Card and I/O data record:if using the new version of SY-SOFT-95A, the card/user capacity can increase to 21,000; High-capacity Device can promote number of User/Card to 63,000 and promote I/O data records to 210,000 at most. The whole speed of CPU promotes to 100 MIPS. (Reference 4. SD Card appendix 4). User can choose the SD CARD module to increase IO records or backup 5. After installing SD Card Module and SD Card, user can backup all data from the the controller data. The slot of SD CARD(MDSD-2) can compatible with the capacity of SD CARD include 256MB 512MB and 1GB. External Device of : controller. 6. Fast update firmware:support to update the firmware on-line through RS485 or Ethernet. 1. Reader 7. While Ethernet network module is added, the communication styles to HOST-PC are polling and auto-transmission. Both of the polling and auto-transmission can The Reader includes SYRDS1 Proximity Card Reader SYRDS5 Proximity run at the same time. The system provides not only efficient transmission but also Card Reader SYRDL5 Mini Proximity Reader SYRDT5 LCD Proximity Card Reader and SYRDF5/F6 Fingerprint Reader. System extendibility:link 8 readers at most. The types of Reader divide into 125K (EM) 13.56M (Mifare). response event immediately. While more and more doors in system, the excellent functions will be presented. 8. The system will send commands to related controller and modules to active fire control and fire alarm automatically through Ethernet converter. The functions also 2. MDDIDO Module can be handled through client PC. 1.4 Specifications Number of Cards 3,500 ~ 63,000; Number of Readers 8 (4 IN, 4 OUT); I/O Records 21,000~3500 (Reference appendix 4); Control s 4 ; Output 4 relay; Input 8 points; LCD Display 16 2 LCD; Indicator 8 LED; Reader Technology SYRIS RS485 format; User PIN 4 digital codes; Communication ports RS485 2,Optional 10M/100M Ethernet; / b WiFi Baud Rate Default 19,200bps, 4,800 9,600 19,200 38,400 57, ,200

5 230, , ,600 1,843,200 (Over 115,200, must use MDNET-2); ID & 01-99; Holidays 366 days; Expand Reader & Module SYRIS series module; Anti Pass-Back Level 3 or Group Anti Pass-Back; Speaker Output Built-in (max 0.2W); Time Zone 60 time zones; Timer 0-32 Timer; Group (Application set) 64 Application Set; Software SY-SOFT-95A / SYW95A-NET-V2 / SYW95A-V3 & V2 & V832.11; Keypad 16key keypad; Humidity 10% to 95% (Non-condensing); Operating Temperature --20 to 70 ; Power Supply 8V to 24V DC / 0.3W to 3W; Dimensions(mm) 135W 175H 45D () / 122W 117H 25D (Control Board); Ethernet TCP/IP Module Optional MDNET-2; SD Card Module Optional MDNSD-2 & SD Card 256M 512M 1G; Wiegand Module Optional MDWIE-2; Power Supply Module Over Ethernet Optional MDPOE-1; Section 2: SY210NT Wire & Quick Installing 2.1 Required Equipment Power supply 12V / DC(required); and Reader connection RS485 twisted pairs; and Computer connection SYLINK-F via USB or RS232; Relay connection Relay connects with electromagnetic lock. 2.2 Selecting a Mounting Location Select a mounting location for the unit using the following guidelines: Next to the door that is being supervised; To avoid setting controller in huge noise areas; It is recommended that setting up location should be visible for flashing card to access easily. The height of setting location should between 45 to 50 inches to the floor. 2.3 Typical Mounting Diagram 2.6 Connecting Lock Wiring Diagram Open by power supply failure wiring diagram +12V Normal Close (NC) Common (COM) Normal Open (NO) + - Electric Deadbolt Electric Strikes Open by start power supply wiring diagram Electronic Lock wiring diagram 2.7 Connecting button to Open 2.4 Installing SY210NT 1. Separate the controller and its back panel by pulling the upper side; 2. Use the back panel to mark the screw holes position on the wall; 3. Screw back panel on the wall by using four (4) screws (provided); 4. Put back controller to the back panel; 2.8 Connecting the detection 2.5 Installing the Reader Wiring Diagram 2.9 Connecting power supply +V+VM

6 2.10 General Wiring Diagram Section 4: SY210NT V5 Settings 4.1 System Functions Functions ID Set ID when s are serious connection (EX:First controller ID: 0001 ; Second controller ID:0002). <Setting> Same Card Time The period means flashing one card twice or continuous. <Setting> Section 3: SY210NT V5 Setting Introduction Enlarge 3.1 Setting Menu MU 3.2 Setting Menu Logout MU input password. success. or MU 3.3 Show Version MU Logout yyyy/mm/dd (Thu) hh:mm:ss Using choice to logout. Show time expresses successfully. or MU SY210NT4V S/N:XXXXXXXX Using choice to version information. 3.4 SY210NT Factory Defaults Description Factory Default 1234 ID Same card PIN lock ID:[0001] [0000] sec [3] 次 Invalid Lock While user input invalid password over setting times, the system will lock down. User can't input when system lucked. <Setting> Comm. Baud rate Communication Baud rate (4A/4R). Default is e.8.1. <Setting> DI Setting The NO/NC settings of DI are in control and module. <Setting> Elevator Mode Enable elevator function to control elevator. <Setting> Card Volume Set the max number of card. <Setting> Module Auto Detect Module The system will search new added module by setting the function enabled. <Setting> Module ID Setting Set up module ID by input serial number. <Setting> MDWIE-2 ID Setting Set up reader channel ID.<Setting> Relay Set up the parameters of door open relay. <Setting> Push Button ( Open) Set up the parameters of push button that is used for door open. <Setting> APB Setting Set up the level of APB (0~3).<Setting> Lock time Comm. Baud rate Elevator mode [060]sec e.8.1 [4A] e.8.1 [4R] [NO] Setting Setting. Change password in unpredictable period is recommended. <Setting> Max card Relay Push button ID:[1~4] CH:[1~4] Times 05 sec No APB setting [0] System Utility Backup 60 Day(Optional MDNSD-2 & SD Card) Add Card Add Card. <Setting> Delete Card Delete Card. <Setting> System Utility Date Setting Set date according to user request. <Setting> Time Setting Set time according to user request. <Setting> System Reboot Reboot system. <Setting> 6 Data Backup / Restore

7 Backup/Restore data to system (SD Card required). <Setting> System Initial Set system to default factory setting. <Setting> 4.2 Card Management Add Card Auto Add Card By Serial Add the card automatically by serial (flash card continuously). <Setting> Add Card By Card No. Add the card by card number.(set card ID first then flash card) <Setting> Edit Card Edit Card Status Set the card as enabled or disabled. <Setting> Edit Card PIN Edit the card PIN (4 digital codes). <Setting> Edit Card APB Set APB of card as enabled or disabled. <Setting> Delete Card Delete Card by Card Number Delete car by card number. <Setting> Delete All Cards <Setting> Delete all cards in controller Show Card After flashing the card, system will show card information. <Setting> All Card APB Setting All card APB condition setting. <Setting> 4.3 Fingerprint Management Add Fingerprint Add fingerprint. <Setting> Delete Fingerprint Delete single fingerprint. <Setting> Delete All Fingerprint Delete all fingerprints. <Setting> Section 5: Set up SY210NT V5 Step by Step 5.1 Function MU or MU Set ID [ _ ] System input password success or MU Same card time Same card time 000 sec Invalid Lock System input setting value. or MU Baud Rate Setting System PIN lock Error number [3] Lock time [060] sec input setting value. input setting value. or MU DI Setting System Comm. Baud rate Baud rate(4a) [19200,e,8,1] Baud rate(4r) [19200,e,8,1] Using choice rate, Using choice rate, or MU Elevator Mode System DI Setting ID [ 0 ] DI setting NO/NC:[ ] ID:0 is controller ID:1-8 is MDDIDO input setting value. 0=NO, 1=NC or MU Elevator mode Elevator mode [ No ] Set Max Card System Using choice YES / NO. or MU Max card Max card [ ] Record clear! [ No ] Card:[ ] Record:[ ] input setting value. Using choice YES / NO (Chooses YES only then to be able to change the setting value). Card:Max card number Record:Max I/O data. NOTE:If the user determines the change controller max card, then must first the data backup. After Record clear! [YES], IO data completely will delete 5.2 Reader Module Setting MU System [ _ ] input password Same Card Time ID ID 0001 input ID. or MU System Module success. System 7

8 5.2.1 Module Auto Detect System Module or MU Module Auto detect Auto detect Waiting. Find module:[ 02 ]! Reader Module ID Setting System Module auto detect display. Found two modules. or MU MDWIE-2 ID Setting System Module Module ID setting ID setting [ SYRDS1/S5/L5 ] S/N [ _ ] Module ID [ 0 ] Using choice module. input serial number. input module ID. or MU MDWIE-2 ID setting MDWIE-2 CH-ID [ ] MDWIE-2 ID setting 5.3 Function Setting MU Using choice Reader Channel ID and input Channel ID. or MU Relay System [ 1~4 ] [ _ ] System No :[ 1 ]. input password. success. setting door. or MU Push Button System [ 1~4 ] Relay Relay ID:[ 0 ] CH:[ 01 ] Time [ 005 ] sec input ID and CH. input time. or MU APB Setting System [ 1~4 ] Push button Push button ID:[ 0 ] CH:[ 01 ] input ID and CH. or MU APB setting APB setting Level: [ 0 ] setting level 0~ Card Function Setting MU or MU PIN Setting System [ _ ] input password. success. 按鍵顯示畫面備註 or MU Add Card System PIN setting No:[ 1 ] PIN setting [ _ ] input number (1-3). input password. or MU Delete Card System Add card No:[ 1 ] Punch card input number (1-3). Please punch the card. or MU 5.5 System Utility MU Delete card No:[ 1 ] input number (1-3). or MU Date Setting System System utility [ _ ] System System utility input password. success. or MU Time Setting System System utility System utility Date setting Date setting [ 07 / 08 / 15 ] setting date. (YY/MM/DD). 按鍵顯示畫面備註 or MU System Reboot System System utility System utility Time setting Time setting [15:00:37 ] setting time.(hh:mm:ss) or MU System utility Reboot 8

9 System Reboot [ No ] Data Backup / Restore System System utility (The use in optional SD Card Module) Uses the SD card backup data Using choice YES / NO. or MU System utility Backup / Restore Backup / Restore [ Manual Backup ] 2007/06/22 16:19 [ YES ] Manual backup [ Waiting xxxx ] Manual backup Uses the SD card restore data Using choice Backup or Restore. Using choice YES / NO. Start a backup display. Backup success. or MU System Initial System System utility System utility Backup / Restore Backup / Restore [ Manual Restore ] Restore from [ Manual Backup ] 2007/06/22 16:19 [ YES ] Restore [ Waiting xxxx ] System Reboot Using choice Manual Backup or Restore. Using choice Manual Backup / Auto Backup. Using choice YES / NO. Start a restore display. After restore success system automatic reboot. or MU 5.6 Card Management System utility Initial Initial [ YES ] System Reboot Using choice YES / NO After system reboot resetting system unit to factory defaults. Punch card Please punch the card. (can punch card continuously) NOTE:The manual serial number increases the card commonly used in to increase some specific serial number the card. If punch card continuously, the number will from input number starts to increase. EX:Input number 1000,when punch second card can jump Edit Card Card Condition Setting (Valid / Invalid) Card or MU Card PIN Setting Edit card Card No.:[00001] Edit card Status Status [ Enable ] Card Card No.:[00001] input number. Using choice Status APB or PIN Using choice Enable or Disable Card APB Setting Edit card PIN PIN [ YES ] PIN PIN:[ 0000 ] Card Card No.:[00001] Using choice Status APB or PIN Using choice YES / NO input password Single Card Delete Card Edit card APB APB [ Disable ] Using choice Status APB or PIN Using choice Enable or Disable or MU Delete card MU [ _ ] input password. success Delete All Card Delete card By no. Delete card No.:[00001] Using choice By no. or All. input number. or MU Card Card Delete cards Add Card Add Card By Serial Card or MU or MU Add Card By No. Add Card Add Card By serial Punch card Using choice By serial or By No. Please punch the card. (can punch card continuously) or MU Add Card Cards Browse Card Delete card All Delete All [ Yes ] Delete All Using choice By no. or All. Using choice YES / NO. Delete all card success. or MU Show card ID Punch card Please punch the card B Show data of the card. or MU Add Card By No. Add Card No.:[01000] Using choice By serial or By No. input number All Card APB Setting Card 9

10 MU or MU All card APB setting APB setting [ Enable ] Using choice Enable Disable or Reset 5.7 Fingerprint Management Connection Fingerprint Reader uses. MU or MU [ _ ] Fingerprint Fingerprint ID:[ 1 ] input password. success. input fingerprint ID Add Fingerprint Fingerprint Fingerprint ID:[ X ] or MU Fingerprint Add Fingerprint No:[ 0001 ] Fingerprint Add Fingerprint No:[ 0002 ] input fingerprint number. After the bi bi voice press the fingerprint to press on the fingerprint sensor. The bright OK green light expresses successfully. Add fingerprint or use CLR exit Delete Fingerprint Fingerprint Fingerprint ID:[ X ] or MU Fingerprint Delete Fingerprint No:[ 0001 ] Fingerprint Delete Delete All Fingerprint Fingerprint Fingerprint ID:[ X ] input fingerprint number. After serge the long sound, deletes successfully. or MU Fingerprint Delete all Delete all [ Yes ] Delete all Waiting Delete all Using choice YES / NO. Fingerprint deleting. Delete all fingerprint success. 5.8 Resetting the SY210NT Unit to Factory Defaults Please refer to

11 Appendix 1:Quick Reference Programming Table Quick Reference Programming Table 1. System ID 2. Same card Time 3. PIN Lock 4. Comm. Baud rate 5. DI setting 6. Elevator mode 7. Max card 2. Module 1. Auto detect 2. ID setting Relay 2. Push button 3. APB setting PIN setting 2. Add card 3. Delete card 5. System Utility 1. Date setting 2. Time setting 3. Reboot 4. Backup / Restore 5. System Initial 2. Card 3. Fingerprint 1. Add card 1. By serial 2. By no. 2. Edit card 1. Status 2. PIN 3. APB 3. Delete card 1. By no. 2. All 4. Show card ID 5. All card APB setting 1. Fingerprint Add 2. Fingerprint Delete 3. Fingerprint Delete all 11

12 Appendix 2:Programming Worksheet Installation Information 1. Set Name: Programming Worksheet 2. Device Title: 3. Device ID: 4. Installs Company: 5. Reader Number: 6. Tel.: Device Setting Information Item Default Setting Value 1234 Same Card Time 0 PIN Lock Error Number 3 PIN Lock Time 60 sec sec Baud Rate (4A) 19200,e,8,1,,, Reader Baud Rate(4R) 19200,e,8,1,,, Elevator Mode No Max Card Relay ID: CH: ID:_-_-_-_ CH: Relay Time 005 sec / / / sec Push Button ID: CH: ID:_-_-_-_ CH: APB Setting Level:0 / 0/ 0/ 0 Level: / / / SD Card Backup Data Time yyyy / mm / dd / / 12

13 Appendix 3:Card Information Record Sheet Cardholder Name Card Number Auxiliary Card PIN 13

14 Appendix 4: SY210NT V5 Card Capacity and I/O Data List SY210NT V5 Card Capacity and I/O Data List 1. Normal(SSB,TSB) 1. High-capacity (SSA,TSA) 2.High-capacity (SSA-L,TSA-L) Card Capacity I/O DATA Card Capacity I/O DATA Card Capacity I/O DATA

15 Appendix 5:Using the SY210NT System Q1: How to setting reader ID? What Reader ID and are relate? MU A1:SY210NT-V5 series oneself have no inside set up to read card system, [1234 ] input password. After expansion installs Reader can use reader card function. ID and OK The Setup lamp signal is bright Setup, success. Reader ID are setting [1] by factory default, so after setting Reader ID *2 System expansion installs Reader, Otherwise can deliver failure because ID duplicates. Reader module ID setting *1 Module MU [1234 ] input password. Module Auto detect Auto detect Waiting ID: xx Find Module :[01] OK automatic detects display. Found one module. OK The Setup lamp signal is bright Setup, success. CLR*4 2007/12/30 (Sun) 17:52:53 Setting success. *2 System Note 4: can automatic detects Modules and connected. In normal condition, if installed two devices,then system demonstrate Find Module:[02] OK. *1 Module Module Auto detect *1 Module ID Setting ID Setting [ SYRDS1 / S5 / L5 ] Reader module ID setting Using choice module. (Note 1) module ID setting (Note 3) S / N [ ] Input serial number. (Note 2) CLR*3 Module ID [1] Module ID Setting 2007/12/30 (Sun) 17:52:53 Input Module ID. Presses the key confirmation ID setting. Setting success. Reader ID setting step by step: Note 1:The module can differentiate as follows. READER DIDO PRINT SYRDK5 SYRDF5/F6 SYRDT5 Proximity Card Reader. Have SYRDS1, SYRDS5, SYRDL5 and MDWIE. Extend Module. Have MDDIDO-1S and MDDIDO-16. Printer Module. Keypad Proximity Reader. Fingerprint Reader. LCD Proximity Card Reader. Note 2:User can find the serial number on the packing box or serial number label at the back of device. Note 3:Readers ID alignment rule as follows, External Reader: ID: 1 ID: 2 ID: 3 ID: 4 Internal Reader: ID: 5 ID: 6 ID: 7 ID: 8 automatic detects Readers and Modules. After setting Readers ID has to can take effect with connected. The setting step by step as follows: 15

16 Q2: How to add the card? A2: Add Cards Q3: How to setting the push button from controller? A3: DI1 is push button of 1 MU [1234 ] OK *3 Card Please punch the card. (Has not used) Please punch the card. (Has used) CLR Add Card Add Card By Serial Punch Card Punch Card [0001] Punch Card Card Use Add Card By Serial input password. The Setup lamp signal is bright Setup, success. Automatic add cards by serial. Please punch the card. (Has not used) The first input card 0001 starts to sort. Punch card continuously then number automatic increasing. If the card has already used system would appear a message Card Use. MU *2 *2 [1234 ] OK System input password. The Setup lamp signal is bright Setup, success. No : [1] [1] Expresses the 1. *1 Push button Push button ID : [0] CH : [01] Push button Push button setting. DI setting ID:[0] Indicate to be in use controller inner part, CH:[01] Indicate to be in use channel 01. Presses the key to confirmation. CLR*3 2007/12/30 (Sun) 17:52:53 Setting success. 16

17 Q4: How to Connect HID Readers of Wiegand interface with? A4:Connect Wiegand Module wiring diagram. SY210 4R+ 12V (Yellow Wire) NC1 (Brown Wire) COM1 (Orange Wire) NO1 (Yellow Wire) NC2 (Green Wire) COM2 (Blue Wire) NO2 (Violet Wire) +12VDC EM Lock EM Lock BLACK GRE D1 WHITE D0 BLACK GRE D1 WHITE D0 (Green Wire) (Black Wire) (Red Wire) 4R+ 4R- 4R- 12V (Yellow Wire) ID #1 ID #5 ID #2 ID #3 BLACK GRE D1 WHITE D0 BLACK GRE WHITE D1 D0 HID HID HID HID (Green Wire) (Black Wire) (Red Wire) M4 M2 M3 M5 DI1 (Brown Wire) DI2 (Orange Wire) DI3 (Yellow Wire) DI4 (Green Wire) (Black Wire) 4A- (Blue Wire) 4A+ (Violet Wire) 4R- (Gray Wire) 4R+ (White Wire) (Black Wire) Magnetic sensors ( sensors) ********Note******* (4A-) and (4A+) are used to connect to other controller or converter ******************* 17

18 Q5: How to use MDDIDO Module Connecting the Exit Detector or Exit Button? A5: Connecting the Exit Detector or Exit Button wiring diagram The Appliance of MDDIDO-1S with SY210NT controller SY210NT-V5 M4 M2 NC1 COM1 NO1 NC2 COM2 NO2 4A- 4A+ 4R- 4R+ + 12VDC (Brown Wire) (Orange Wire) (Yellow Wire) (Green Wire) (Blue Wire) (Violet Wire) (Blue Wire) (Violet Wire) (Gray Wire) (White Wire) (Black Wire) EM Lock EM Lock ********Note******** (4A-) and (4A+) are used to connect to other controller or converter ******************** M3 DI1 DI2 DI3 DI4 (Brown Wire) (Orange Wire) (Yellow Wire) (Green Wire) (Black Wire) Magnetic sensors ( sensors) M5 4R+ (Yellow Wire) 4R- (Green Wire) (Black Wire) 12V (Red Wire) (Brown Wire) (Orange Wire) (Yellow Wire) (Green Wire) (Black Wire) DI1 DI2 DI3 DI4 Exit Buttons (Brown Wire) (Orange Wire) (Yellow Wire) (Green Wire) (Blue Wire) (Violet Wire) COM1 NO1 COM2 NO2 4R+ (Yellow Wire) 4R- (Green Wire) (Black Wire) 12V (Red Wire) (Brown Wire) DI1 (Orange Wire) DI2 (Yellow Wire) DI3 (Green Wire) DI4 (Black Wire) Break glass switches Normal Close ( NC ) Common ( COM ) Normal Open ( NO ) Relay DO Feature 10A 28VDC / 5A 250VAC (Brown Wire) (Orange Wire) (Yellow Wire) (Green Wire) (Blue Wire) (Violet Wire) COM1 NO1 COM2 NO2 18

19 MU *2 [1234 ] OK System input password. The Setup lamp signal is bright Setup, success. *2 No : [1] [1] Expresses the 1. *1 CLR*3 Push button Push button ID : [1] CH : [01] Push button 2007/12/30 (Sun) 17:52:53 Push button setting. DI setting ID:[0] Indicate to be in use expansion module1, CH:[01] Indicate to be in use channel 01. Presses the key to confirmation. Setting success. 19

20 Appendix 6: General Wiring Diagram SY210NT-V5 SERI AL CONTROLLER WIRING DIAGRAM 控制器接線圖 Relay Relay Max : 7A 30VDC / 7A 250VAC Normal Close ( NC ) Common ( COM ) Normal Open ( NO ) DO Feature External Speak 外接喇叭 RELAY 3 RELAY 4 M15 (Brown Wire 棕色 ) (Orange Wire 橙色 ) (Yellow Wire 黃色 ) (Green Wire 綠色 ) (Blue Wire 藍色 ) (Violet Wire 紫色 ) (Brown Wire 棕色 ) (Orange Wire 橙色 ) (Yellow Wire 黃色 ) (Green Wire 綠色 ) (Blue Wire 藍色 ) (Violet Wire 紫色 ) NC 3 COM 3 NO 3 NC 4 COM 4 NO 4 NC 1 COM 1 NO 1 NC 2 COM 2 NO 2 LCD DISPLAY 顯示器 Keyboard and LED 鍵盤及燈號 2007/01/01 (Mon) *** 09:05:37 *** POE Power Over Ethernet 網路供電模組 POE RELAY 1 RELAY 2 MDNET-2 Ethernet Module 乙太網路模組 MDNET-2 Wiegand Module 維根模組 DI5 DI6 DI7 DI8 Wiegand (Blue Wire 藍色 ) (Violet Wire 紫色 ) (Gray Wire 灰色 ) (White Wire 白色 ) (Black Wire 黑色 ) (Brown Wire 棕色 ) (Orange Wire 橙色 ) (Yellow Wire 黃色 ) (Green Wire 綠色 ) (Black Wire 黑色 ) DI1 DI2 DI3 DI4 4R+ 4A- 4R- 4R+ 4A- 4A+ 4R- 4A+ Connect to SYLINK and other s 連結 SYLINK 與其它控制器 Reader +12Vdc Reade r +12Vdc DIDO Printer Modul e +12Vdc Digital Input 輸入接點 Can be: sensor Push button or other NC/NO output sensor (Black Wire 黑色 ) (Green Wire 綠色 ) BATTERY 備用電池 SD Module SD 記憶卡模組 (White Wire 白色 ) (Red Wire 紅色 ) (Red Wire 紅色 ) 8 ~ 20 Vdc 直流 (Black Wire 黑色 ) (Black Wire 黑色 ) 接地 DC Power Input 直流電源 Tamper SW. 反破壞開關 20