WORKSHOP 2 Solid Shell Composites Modeling

Transcription

1 WORKSHOP 2 Soli Shll Composits Moling WS2-1

2 WS2-2

3 Workshop Ojtivs Bom fmilir with stting up soli omposit shll mol Softwr Vrsion Ptrn 2011 MD Nstrn Fils Rquir soli_shll. WS2-3

4 Prolm Dsription Simult thr-point-ning omposit tst spimn using soli omposit shll lmnts Du to symmtry, only qurtr of th spimn is mol. WS2-4

5 Prolm Dsription (ont.) You will uil lmint y ntring h ply thiknss s prntg of th totl thiknss Two vry thin outr plis r us to pik up strsss t th outsi fs of th prt. Strss rovry ply Mtril Nm % Thiknss Orinttion 1 Ortho Ortho Ortho Ortho Ortho Ortho Ortho Ortho Strss rovry ply 9 Ortho WS2-5

6 Stp 1. Opn n xisting Ptrn Dts Strt Ptrn n opn ts ontining th omposit oupon:. Clik Fil Opn in th Dfults group.. Slt soli_shll. s th Fil nm.. Clik OK. WS1-6

7 Stp 2. Rviw Los n Bounry Conitions g Plot los n ounry onitions:. Clik th Los/BCs t.. St Ation to Plot Mrkrs.. Slt Displ_simpl_ n lik Apply. This plots th simpl support in th vrtil irtion.. Slt Displ_sym1 n lik Apply. This plots th X symmtry onstrints.. Slt Displ_sym2 n lik Apply. This plots th Y symmtry onstrints. f. Slt For_for1 n For_for2 n lik Apply. This plots th ppli lo. g. Clik Rst Grphis to lr th mrkrs. f WS2-7

8 Stp 3. Vrify Elmnt Coorint Systm g Vrify th lmnt oorints systms:. Clik th Mshing t.. St tion to Show.. St Ojt to Elmnt.. St Info to Coor. Sys.. Clik on ny lmnt to rviw th lmnt oorint systm. f. Clik on fw mor lmnts to rviw th lmnt oorint systm. Mk mntl not of th lmnt Z irtion. g. Clik Rst Grphis. f WS2-8

9 Stp 4. Crt Mtril Proprty Crt mtril proprty:. Clik th Proprtis t.. Clik 3D in th Orthotropi group.. Nm th Mtril ortho1. Clik on Input Proprtis. Entr th vlus shown. f. Clik OK. g. Clik Apply. f g WS2-9

10 Stp 5. Dfin th Composit Lyup Crt Lmint Composit:. In th Proprtis t, lik Lmint in th Composit group.. Nm th Mtril lm1.. Clik on ortho1 9 tims to rt 9 rows in th tl. Slt Totl-%thiknss from th Stking Squn Convntion. Clik in th first %thiknss ll f. Clik in th Input Dt fil n ntr n prss th Entr ky. g. Rpt stp f to ntr ll ply % thiknss vlus s shown on th right. Mk sur th totl prntg is 100 whn you r on. h. Clik in th first Orinttion ll i. Entr th ply ngls on t tim s shown. j. Clik Apply. f g i h WS2-10

11 Stp 6. Crt Soli Proprty Crt 3D soli proprty:. In th Proprtis t, lik Soli in th 3D Proprtis group. (you my hv to mov th Lmint Composit form out of th wy). f. For Proprty St Nm, ntr 3-omp.. Chng Options to Lmint.. Clik Input Proprtis. Clik Mtril Prop Nm ion n slt lm1. f. Clik in th Mtril Orinttion ox, thn srn slt Coor 1. g. For Thiknss Dirtion 3D, slt Elmnt Z Dirtion. h. In SCOMP Intgrtion Shm, slt Assum Strin. i. Clik OK. f i g h WS2-11

12 Stp 6. Crt Soli Proprty (Cont.) Crt 3D soli proprty:. Clik Slt Applition Rgion. Rtngl slt oth solis.. Clik A.. Clik OK.. Clik Apply. WS2-12

13 Stp 7. St up Anlysis Slt solution typ:. Clik th Anlysis t.. Entr thr_point_ning for Jo Nm.. Clik on Solution Typ.. Slt Impliit Nonlinr.. Clik Solution Prmtrs. f. Chk Shll Shr Corrtion n SOL 400 Run. g. Clik OK. h. Clik OK. g f h WS2-13

14 Stp 7. St up Anlysis (Cont.) Dfin sus prmtrs: i. Clik Suss. j. Slt Dfult k. Clik Sus Prmtrs. l. St Linrity to Linr. m. Clik OK. n. Clik Apply. o. Clik Cnl. p. Clik Apply. l j Th nlysis will tk lss thn minut to run. m k i n o p WS2-14

15 Stp 8. Atth Rsults Atth th rsults fil:. Clik MASTER / DBALL in th Ass Rsults group.. Clik on Slt Rsults Fil.. Slt th rsults fil thr_point_ning.master.. Clik OK.. Clik Apply. WS2-15

16 Stp 9. Plot Rsults Plot formtion:. Clik th Rsults t.. Clik th Dformtion ion.. Slt Displmnt, Trnsltionl for Dformtion Rsult.. Clik Apply. WS2-16

17 Stp 9. Plot Rsults (ont.) Plot strsss:. Clik th Fring ion.. Slt Composit Strss, Ply Strss for Fring Rsult.. St Position to Lyr 1 t mil.. St Quntity to X Componnt.. Clik Apply. WS2-17

18 En of Workshop 2 Fil/Quit to xit Ptrn. WS2-18