Fire Communicator (DACT)
|
|
- Vanessa Gallagher
- 5 years ago
- Views:
Transcription
1 Fire Communicator (DACT) 1.0 Account Information Account: Name: Address: System Phone Number: Contact Person: Date: Contact Phone: Comments: Communicator Location: Notes:
2 Note: All default values are shown along the right-hand side as follows: DEFAULT:XXXXXX Note: For all programming entries with a row of boxes ( ), place a checkmark ( ) in the appropriate box to indicate the selected setting 2.0 Program Time 2.1 System Date and Time System Date* Set system date (MMDDYY): DEFAULT: System Time* Note: Enter system time in 24-hr military format (HHMM): DEFAULT:0000 Once the user has entered the system date and time, defaulting the D9068 will not reset these entries. However, the system time will not be preserved in the event of a power loss. 2.2 Auto Test Auto Test Time Enter the auto test time in 24-hr military format(hhmm): Auto Test Frequency Place a check in the desired box: DEFAULT:0400 1: 6 hrs 2: 12 hrs 3: 24 hrs DEFAULT:3: 24 hrs 4: 7 days 5: 28 days 6: Disable 2.3 Daylight Savings 3.0 Timers Shaded items are not currently supported. Place a check in either box: Yes No DEFAULT: No 3.1 AC Fail Delay Set in between 00 and 24 hours: DEFAULT: 06 hrs 3.2 Display Rate Range: X.25 seconds: DEFAULT: 4 D B Page Radionics
3 4.0 Program Inputs 4.1 Configure Point 1: Point 2: Point 3: Point 4: Point 5: DEFAULT: Waterflow DEFAULT: Fire DEFAULT: Supervisory DEFAULT: Fire DEFAULT: Fire 4.2 Supervised Point Types 1: Fire 3: Supervisory 5: System Trouble 7: Low Battery 2: Waterflow 4: Monitor 6: AC Fail Place a check in either box: 5.0 Program Relay Point 1: Yes No DEFAULT: No Point 2: Yes No DEFAULT: No Point 3: Yes No DEFAULT: No Point 4: Yes No DEFAULT: No Point 5: Yes No DEFAULT: No Place a check in either box: 1: Release on Trouble 2: Active Ground Start DEFAULT: 1: Release on Trouble 6.0 Program Accounts 6.1 Account Numbers Number 1: DEFAULT: 0000 Number 2: DEFAULT: Phone Numbers Phone #1: DEFAULT:????????? Phone #2: DEFAULT:????????? Phone #3: DEFAULT:????????? Special Phone # Characters Press See Action [Test] 1 * Touch Tone * [Test] 2 # Touch Tone # [Test] 3 / 3 sec delay Shaded items are not currently supported. D Radionics Page B
4 6.3 Phone Control Phone #1 Format: DEFAULT: SIA 300 Phone #2 Format: DEFAULT: SIA 300 Phone #1 Tone: Phone #2 Tone: Phone #1 Text: Phone #2 Text: DEFAULT: 19D, 14A, 10PS DEFAULT: 19D, 14A, 10PS DEFAULT: NO DEFAULT: NO 6.4 Report Steering Format Tone 1: 4/2 Report 1: 19D, 14A, 10PS 2: SIA, 110 2: 18D, 23A, 10PS 3: Contact ID 3: 19D, 14A, 20PS 4: SIA 300 4: 18D, 23A, 20PS 5: Modem III 5: 19D, 14A, 40PS 6: 18D, 23A, 40PS Non-SUP Alarm Supervisory Alarm Alarm Restore, Reset Supervisory Restore Tests Trouble, Trouble Restore Report Steering Selections 1: Phone 1 Only 3: Phone 1 & 2 2: Phone 2 Only 4: Phone 2 Backup 6.5 Line Control Line 1 Dialing Type:* Line 2 Dialing Type:* DEFAULT: Tone/Pulse DEFAULT: Tone/Pulse Place a check in either box: Line 1 Monitor Line: Yes No DEFAULT: Yes Line 2 Monitor Line: Yes No DEFAULT: Yes Line 1 Wait Dial Tone: Yes No DEFAULT: Yes Line 2 Wait Dial Tone: Yes No DEFAULT: Yes *Dialing Type Selections: Pulse Only, Tone/Pulse, Tone Only 6.6 Ack Wait Time Range: 20 to 99 seconds: DEFAULT: 45 D B Page Radionics
5 7.0 Program Formats 7.1 4/2 Point Rpt Fire Alarm (Data Range: 0-9, A-F): Digit 1 DEFAULT: 0 Fire Rstrl (Data Range: 0-9, A-F): Digit 1 DEFAULT: 3 Waterflow (Data Range: 0-9, A-F): Digit 1 DEFAULT: 0 Supervise (Data Range: 0-9, A-F): Digit 1 DEFAULT: 0 Trouble (Data Range: 0-9, A-F): Digit 1 DEFAULT: 6 Trbl Rstrl (Data Range: 0-9, A-F): Digit 1 DEFAULT: 3 Disable (Data Range: 0-9, A-F): Digit 1 DEFAULT: B Disable Rtrl (Data Range: 0-9, A-F): Digit 1 DEFAULT: 3 Monitor (Data Range: 0-9, A-F): Digit 1 DEFAULT: 0 Zone 1 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 1 Zone 2 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 2 Zone 3 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 3 Zone 4 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 4 Zone 5 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 5 Zone 6 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 6 Zone 7 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 7 Zone 8 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 8 Zone 9 (Data Range: 0-9, A-F): Digit 2 DEFAULT: 9 Zone 10 (Data Range: 0-9, A-F): Digit 2 DEFAULT: /2 Rpt Codes Group 1 SYSTM IN TST (Data Range: 0-9, A-F): SYS TEST RST (Data Range: 0-9, A-F): SILENCE (Data Range: 0-9, A-F): FIRE DRILL (Data Range: 0-9, A-F): FIRE DRL RST (Data Range: 0-9, A-F): OPEN RST RPT (Data Range: 0-9, A-F): LOW BATTERY (Data Range: 0-9, A-F): LOW BATT RST (Data Range: 0-9, A-F): AC FAILURE (Data Range: 0-9, A-F): DEFAULT: F1 DEFAULT: E1 DEFAULT: 9F DEFAULT: F2 DEFAULT: E2 DEFAULT: 9F DEFAULT: F9 DEFAULT: E9 DEFAULT: F8 D Radionics Page B
6 7.3 4/2 Rpt Codes Group 2 AC FAIL RST (Data Range: 0-9, A-F): AUTO TST RPT (Data Range: 0-9, A-F): OFF NORM TST (Data Range: 0-9, A-F): PHONE 1 TRBL (Data Range: 0-9, A-F): PH 1 TRB RST (Data Range: 0-9, A-F): PHONE 2 TRBL (Data Range: 0-9, A-F): PH 2 TRB RST (Data Range: 0-9, A-F): SYSTEM TROUB (Data Range: 0-9, A-F): SYS TRB RST (Data Range: 0-9, A-F): DEFAULT: E8 DEFAULT: EE DEFAULT: FB DEFAULT: EB DEFAULT: FC DEFAULT: EC 7.4 4/2 Rpt Codes Group 3 MAN TST RPT (Data Range: 0-9, A-F): DATA LOST RP (Data Range: 0-9, A-F): EEPROM FAIL (Data Range: 0-9, A-F): RESET REBOOT (Data Range: 0-9, A-F): SMK PWR TRBL (Data Range: 0-9, A-F): SMK PWR RSTR (Data Range: 0-9, A-F): GND FLT TRBL (Data Range: 0-9, A-F): GND FLT RSTR (Data Range: 0-9, A-F): TRBL INP RPT (Data Range: 0-9, A-F): DEFAULT: FE DEFAULT: FF 7.5 4/2 Rpt Codes Group 4 TRBL INP RST (Data Range: 0-9, A-F): ANALOG SERVC (Data Range: 0-9, A-F): ANALOG RESTR (Data Range: 0-9, A-F): EQUIP FAILUR (Data Range: 0-9, A-F): EQUIP RESTOR (Data Range: 0-9, A-F): NETWORK FAIL (Data Range: 0-9, A-F): NETWORK RSTR (Data Range: 0-9, A-F): SENS BUS RPT (Data Range: 0-9, A-F): SENS BUS RST (Data Range: 0-9, A-F): Shaded items are not currently supported. D B Page Radionics
7 7.6 Rpt Codes Group 5 RMT PGM FAIL (Data Range: 0-9, A-F): RMT PGM SUCC (Data Range: 0-9, A-F): UNKNOWN FALT (Data Range: 0-9, A-F): 7.7 SIA Silence Rpt Left Byte (Data Range: 0-9, A-F): D9068 DEFAULT: FF DEFAULT: 4B Right Byte (Data Range: 0-9, A-F): DEFAULT: Program Defaults Note: There are no permanent programmable items under PROGRAM DEFAULTS. 9.0 Serial Connection Serial Connection Enabled: DEFAULT: NO Shaded items are not currently supported. D Radionics Page B
8 Notes 2001 Radionics, a division of Detection Systems, Inc. PO Box 80012, Salinas, CA , USA Customer Service: (800) B 06/04 D9068 Page 8 of 8
FPD-7024 Fire Alarm Control Panel Version 1.03
FPD-7024 Fire Alarm Control Panel Version 1.03 Program Record Sheet Account Information: Account: Date: Name: Address: Panel Phone #: Contact Phone #: Contact Person: Comments: Panel Location: Notes: Program
More informationD2112 Keypad Diagnostics
D2112 Keypad Diagnostics Putting the Keypad into the Diagnostics Mode 1. Lock the D2112's Standby Switch down. 2. Press the 1 key on the keypad. 3. Enter your Installer passcode. The default Installer
More informationVISTA-128BP/VISTA-250BP Programming Form
VISTA-128BP/VISTA-250BP Programming Form Some fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system, see the Partition-Specific Fields section
More information*00 INSTALLER CODE Enter 4 digits, 0-9 [4140] *28 POWER UP IN PREVIOUS STATE [1=yes] 0=no; "1" for UL.
4140XMPT2 PROGRAMMING FORM Some fields are programmed for each partition (shown as shaded fields). See the PARTITION-SPECIFIC section for programming these fields. Standard default (*97) values are shown
More informationPFC-6006 Reporting Codes Summary
Report by Point The following table identifies the reporting codes generated for specific panel events when reporting by point. Report By Point SIA Format Contact ID Format System Power Up RR 1 305 00
More information4140XMPT2 PROGRAMMING FORM
414XMPT2 PROGRAMMING FORM Some fields are programmed for each partition (shown as shaded fields). See the PARTITION-SPECIFIC section for programming these fields. Standard default (*97) values are shown
More informationCommercial Fire and Burglary Partitioned Security System with Scheduling. Programming Guide. K0376PRV5 2/11 Rev. A
VISTA-128FBP VISTA-250FBP Commercial Fire and Burglary Partitioned Security System with Scheduling Programming Guide K0376PRV5 2/11 Rev. A Table of Contents Programming Field Settings for UL864 Compliance
More informationProperty of Monitronics Inc
Enter Program (Locations 034 to 410) 1. Press Program Button on main panel 2. At keypad press 9 + Program Code (9 8 7 6 5) or 1. Power down with black switch on bottom left of panel 2. Power up while holding
More informationVISTA-50P VISTA-50PUL
VISTA-50P VISTA-50PUL PARTITIONED SECURITY SYSTEM with SCHEDULING Quick Start Step-by-Step Programming Procedure Single And Multiple Partition Programming Forms System Worksheets VISTA50P-PR 8/95 (See
More informationDigiplex EVO High Security and Access System What s New EVO192 V2.7
Digiplex EVO High Security and Access System What s New EVO192 V2.7 Overview New zone programming and additional zone/system/anti-mask options EN 50131 compliancy Now supports automatic label broadcast
More informationENABLE / DISABLE: ZONES, DEVICES, CIRCUITS, COMMUNICATION SENSE, RESET HI-LO LEVELS, WALKTEST DIAGNOSTICS
Cheetah Manual #06-148 page 55 CHAPTER 10 Operation (level 2 password) Menu options available under this level of access are: HISTORY: ALARM, EVENT, ZONE, CURRENT LEVEL PASSWORD: (ENTRY) 1 SPECIAL: LEVELS,
More informationTelephone and Reporting Setup in ElkRP
Telephone and Reporting Setup in ElkRP 1. To add a telephone, right click on Telephones under Folder items on the left side of the screen. Then select New Telephone. 2. On the New Telephone IDs screen,
More information&RPPHUFLDO)LUHDQG%XUJODU\ 3DUWLWLRQHG6HFXULW\6\VWHP ZLWK6FKHGXOLQJ
9,67$)% &RPPHUFLDO)LUHDQG%XUJODU\ 3DUWLWLRQHG6HFXULW\6\VWHP ZLWK6FKHGXOLQJ 4XLFN6WDUW*XLGH FIRE FIRE * PULL V128FB-PRV1 10/98 2 Table Of Contents RECOMMENDED PROGRAMMING PROCEDURE... 4 PROGRAM FIELD CATEGORIES...
More informationTABLE OF CONTENTS. Notice...i How to Use This Program Entry Guide...i About the Type Styles That We Use in the Text...i D5200 Key Descriptions...
TABLE OF CONTENTS Notice...i How to Use This Program Entry Guide...i About the Type Styles That We Use in the Text...i D5200 Key Descriptions...ii PROGRAMMING THE D6500...1 LINE CARD Create Custom Programs
More informationAdemco/Protection One 250P1-1 Programming Form
Ademco/Protection One 250P1-1 Programming Form Local programming requires the use of a 2-line Alpha keypad connected to the keypad terminals on the control. Field Function Programmed Values [ ] = Default
More information3DUWLWLRQHG6HFXULW\6\VWHPV ZLWK6FKHGXOLQJ
)$&&$&% )LUHDQG%XUJODU\ 3DUWLWLRQHG6HFXULW\6\VWHPV ZLWK6FKHGXOLQJ **** **** ARMED READY A B C D FIRE FIRE First Alert OFF AWAY STAY 1 2 3 4 5 6 7 8 9 MAXIMUM TEST BYPASS INSTANT CODE CHIME READY * 0 #
More informationProgramming Worksheets
Now classified in accordance with ANSI/SIA CP-01-2000 (SIA-FAR) Programming Worksheets PC1555 CP-01 PC1555 CP-01 version 3.2 DLS2002 and higher Page references below are to the accompanying Installation
More informationSOFTWARE VERSION 3.10
738PEP-03 SOFTWARE VERSION 3.10 HEXA PROGRAMMING: Addresses 000 to 043 and 300 to 527 are programmed using the Hexa Programming method. In this mode, you can enter any hexa-digit from 0-F where keys [1]
More information3 6HFXULW\6\VWHP 3URJUDPPLQJ)RUP K4332 9/99 BYPASS NOT READY ARMED READY 4 MAX 5 TEST 6 BYPASS 7INSTANT 8 CODE 9CHIME READY ARMED
3 6HFXULW\6\VWHP 3URJUDPPLQJ)RUP ARMED READY 1 OFF 2 AWAY 3 STAY 4 MAX 5 TEST 6 BYPASS 7INSTANT 8 CODE 9CHIME READY 0 # * NIGHT NO AC AWAY PHONE TEST BYPASS NOT READY ALARM STAY CHIME BAT FIRE CHECK INSTANT
More informationCUSTOMER INFORMATION
CUSTOMER INFORMATION COMPANY NAME & ADDRESS: CONTACT: PHONE: FAX: NOTES: DATE ENTERED: DATE MODIFIED: 11/2/2010 12:41 P 11/2/2010 12:47 P USER_DEFINED_FIELD1: USER_DEFINED_FIELD2: Vista15PSIA-3 PROGRAMMING
More informationHigh Security and Access System EVO48 V2.1 EVO192 V2.1
High Security and Access System EVO48 V2.1 EVO192 V2.1 Programming Guide Includes LCD Keypad Programming We hope this product performs to your complete satisfaction. Should you have any questions or comments,
More informationProperty of Monitronics Inc
Enter Program 1. Master Code + 8 + 0 + 0 (Display should show 20) or Power down then back up and press * and # within 1 minute (If exiting programming you can re-enter within 1 minute by pressing * and
More informationCommercial Burglary Partitioned Security System With Scheduling. Programming Guide. K5894PRV4 6/04 Rev A
ADEMCO VISTA SERIES VISTA-128BP/VISTA-250BP/ VISTA-128SIA Commercial Burglary Partitioned Security System With Scheduling Programming Guide K5894PRV4 6/04 Rev A Table of Contents Recommended Programming
More informationR A D I O N I C S. D7212B Control/Communicator Program Entry Guide C 9/95
R A D I O N I C S D7212B Control/Communicator Program Entry Guide 74-06915-000-C 9/95 Notice The material and instructions covered in this manual have been carefully checked for accuracy and are presumed
More informationVISTA-20BAY PROGRAMMING GUIDE SECURITY SYSTEM SINCE 1946
VISTA-20BAY SECURITY SYSTEM PROGRAMMING GUIDE SINCE 1946 N7526-4PR 03/98 File No: S1632 Local programming requires the use of a 2-line alpha keypad connected to the keypad terminals on the control. Field
More informationPROGRAMMING HELP GUIDE
DIGIPLEX EVO48-192 PROGRAMMING HELP GUIDE Entering Programming Mode 1) Press and hold the [0] key 2) Enter your [Installer Code] (default-000000) 3) Enter 4-digit [section] you wish to program 4) Enter
More informationVisorALARM PLUS 2U. Operating Instructions
VisorALARM PLUS 2U Operating Instructions Doc. DM375-I Rev. 1.0 May, 2007 INDEX CHAPTER 1 SYSTEM OVERVIEW...1 1. THE VISORALARM PLUS 2U RECEIVER...2 2. THE IP MODULES (MIP/IPDACTS)...3 3. MANAGEMENT AND
More informationControl Panel D9112. Release Notes for Version 7.00 March Introduction. 2.0 Requirements. 4.0 Previous Version 6.
Control Panel D9112 Release for Version 7.00 March 2007 1.0 Introduction Although the D9112 (expanded version) Control Panel is no longer manufactured (replaced by the D9412G), Firmware Update Kits (P/N:
More informationProperty of Monitronics Inc
Enter Program 1. 4112 + 8 + 0 + 0 (Display should show 20) or Power down then back up and press * and # within 1 minute (If exiting programming you can re-enter within 1 minute by pressing * and #) Exit
More informationControl Panel D9124. Release Notes for Version 7.00 March Introduction. 2.0 Requirements. 4.0 Previous Version 6.
Control Panel Release for Version 7.00 March 2007 1.0 Introduction Firmware Update Kits (P/N: D9499-0700) are available for this product. Refer to the D9412G/D7412G Program Entry Guide (P/N: 47775D or
More informationWireless Expander Eclipse WL Installation and Programming Manual
Wireless Expander Eclipse WL Installation and Programming Manual 1. General Information Eclipse WL is a wireless expander module designed for building of hybrid systems with wired control panels Eclipse
More informationMG/SP Series (V4.9/V5.1) What s New
MG/SP Series (V4.9/V5.1) What s New Firmware: SP4000 and SP5 version 5.1 SP5500, SP000, SP7000, and MG5050 version 4.9 (SP5500 pictured) Overview: New Programming Sections New Events New Trouble Display
More informationFA168CPS / FA168CPSSIA FA148CP / FA148CPSIA
MAX INSTANT READY R BYPASS AWAY ARMED READY 1 OFF MAX INSTANT READY R 2 AWAY 3 STAY BYPASS FA168CPS / FA168CPSSIA FA148CP / FA148CPSIA Security Systems Programming Guide ARMED READY A B C D 7 4 1 OFF FA260
More informationProperty of Monitronics Inc
Enter Program Master Code + 8 + 0 + 0 (Display should show 20) or Power down then back up and press * and # within 1 minute (If exiting programming you can re-enter within 1 minute by pressing * and #)
More informationControl Panels. D9412GV4/D7412GV4 v en Release Notes
Control Panels D9412GV4/D7412GV4 v2.03.018 en Release Notes Control Panels Table of Contents en 3 Table of contents 1 Introduction 5 1.1 Requirements 5 1.2 About documentation 5 1.2.1 Related documentation
More informationSOFTWARE VERSION 3.20
48EPEP-00 SOFTWARE VERSION 3.20 HEXA PROGRAMMING: Addresses 000 to 043 and 300 to 527 are programmed using the Hexa Programming method. In this mode, you can enter any hexa-digit from 0-F where keys [1]
More informationVISTA-20SEa. 3-Partition Security System. Programming Form. V20SEaPRV1 9/98
VISTA-20SEa 3-Partition Security System New style cover to be used Programming Form V20SEaPRV1 9/98 Local programming requires the use of a 2-line Alpha keypad connected to Partition 1 keypad terminals
More informationInstallation Instructions
NX-148E-RF LCD Touchpad w/receiver 466-2198 Rev. B May 2005 Product summary The NX-148E-RF Touchpad w/receiver combines touchpad and receiver capabilities into a single device for use with NetworX NX-4,
More informationControl Panel ICP-SOL2-P/ICP-SOL3-P. en Quick Reference Guide
Control Panel ICP-SOL2-P/ICP-SOL3-P en Quick Reference Guide Control Panel Table of Contents en 3 Table of contents 1 Introduction 6 2 Programming 7 2.1 ICON LCD Codepad Programming 7 2.2 TEXT LCD Codepad
More informationQuick Start: 2. Connect AC power first and then the battery. 3. Configure the keypad (see page 44).
R R R HARDWIRE WIRELESS Quick Start:. Refer to the wiring diagram, connect siren, aux. power, pgm. output, remote bus, earth ground, zone and telephone wiring. NOTE: See Installation Instructions (WI99)..
More informationInstaller Notes 4110DL/XM, Vista 10, Vista-20, Via-30PSE
Installer Notes 4110DL/XM, Vista 10, Vista-20, Via-30PSE 1. Programming can only be done with a 6139 Alpha Keypad on Vista-10/20/30PSE models. 2. When entering programming for the first time during Installations
More informationFSK TX CELLULAR PLUS. Installation and Programming Guide. Tel:
FSK TX CELLULAR PLUS Installation and Programming Guide Tel: 0861 105 962 www.fsk.co.za INTRODUCTION The FSK TX Cellular Plus (TXC+) is a highly featured GSM based unit which is used for the transmission
More informationEVOHD. Programming Guide. Version
EVOHD Programming Guide Version 1.11 www.paradox.com Warranty For complete warranty information on this product please refer to the Limited Warranty Statement found on our Web site: www.paradox.com. Your
More informationCIS-331 Fall 2014 Exam 1 Name: Total of 109 Points Version 1
Version 1 1. (24 Points) Show the routing tables for routers A, B, C, and D. Make sure you account for traffic to the Internet. Router A Router B Router C Router D Network Next Hop Next Hop Next Hop Next
More informationGEM-P9600 CONTROL PANEL/COMMUNICATOR
R R R R PROGRAMMING INSTRUCTIONS HARDWIRE WIRELESS GEM-P9600 CONTROL PANEL/COMMUNICATOR GEMINI ARMED STATUS SYSTEM ARMED 0/0/00 0/0/97 :00AM NEXT/YES A 3 D E PRIOR/NO B 56 F AREA C 790G GEMINI SYSTEM ARMED
More informationSOFTWARE VERSION 3.10
728PEP-03 SOFTWARE VERSION 3.10 HEXA PROGRAMMING: Addresses 000 to 043 and 300 to 527 are programmed using the Hexa Programming method. In this mode, you can enter any hexa-digit from 0-F where keys [1]
More informationXR500/XR100 Command Processor Review. a) Zone expanders c) Output expanders b) All of these d) Single point detectors
Name Answer Key Company Address City, State, Zip Instructor Date Your email User Name = Password = XR500/XR100 Command Processor Review 1. may be connected to the LX-Bus. a) Zone expanders c) Output expanders
More informationModules Programming Guide
Modules Programming Guide Programming Methods The modules can be programmed using the following methods: 1) Through the WinLoad Security Management Software. The modules can be programmed at 19,200 baud
More informationFirst Alert FA160C/162C Installer Notes M. Leuck
First Alert FA160C/162C Installer Notes M. Leuck 1. Programming can only be done by 6139 Alpha keypads, standard 6128 keypad cannot be used to program zones 2. Enter programming: Master Code + 8 + 0 +
More informationADEMCO VISTA-48A Security Systems
ADEMCO VISTA-48A Security Systems Programming Guide K0749-1ENPRV1 10/05 Rev. A APPLICABILITY: VISTA-48A controls with microprocessor version 2.2 or higher. TO START PROGRAM MODE, use method A or B (must
More informationInstallation Instructions Model PSC-17C
Installation Instructions Model PSC-17C 17 Amp Power Supply INTRODUCTION The Model PSC-17C from Siemens Industry, Inc. is a high current power supply that provides the Fire Alarm system (Sprachalarmsystem
More informationDAYLIGHT SAVINGS TIME START/END MONTH [ 0 ]0 = Disabled; 1 = Enabled. 1 Start End
RcvrAcct#: Test Date: May, ::PM SYSTEM ENTRY DELAY# [ ] = None, = secs, = secs, = secs, = secs, = secs, = mins [UL installations: The Entry Delay must be set for a maximum of seconds] ENTRY DELAY# [ ]
More informationM2DIS. User Manual.
M2DIS User Manual www.audac.eu 2 Index Introduction 4 Caution servicing 4 User interface 5 Login screen 5 Main screen 6 Output settings 8 Test signals 10 Sound settings 11 Settings screen 12 Input Configuration
More informationCIS-331 Spring 2016 Exam 1 Name: Total of 109 Points Version 1
Version 1 Instructions Write your name on the exam paper. Write your name and version number on the top of the yellow paper. Answer Question 1 on the exam paper. Answer Questions 2-4 on the yellow paper.
More informationVisorALARM PLUS 2U. Operating Instructions
VisorALARM PLUS 2U Operating Instructions Doc. DM375-I Rev. 2.0 November, 2007 INDEX CHAPTER 1 SYSTEM OVERVIEW... 1 1. THE VISORALARM PLUS 2U RECEIVER... 2 2. THE IP MODULES (MIP/IPDACTS)... 3 3. MANAGEMENT
More informationAdemco Vista-20SE/First Alert FA-162C Program Sheet
Enter Program 1. 4112 + 8 + 0 + 0 (Display should show 20) or Power down then back up and press * and # within 1 minute (If exiting programming you can re-enter within 1 minute by pressing * and #) Exit
More informationVISTA 12a / 48a TECHNICAL TRAINING. The Best in Security plus Everyday Convenience & Control
VISTA 12a / 48a TECHNICAL TRAINING The Best in Security plus Everyday Convenience & Control Version #.007 7th June 2005 VISTA 12a / 48a Training Guide Index 1. Vista Family Features....... p. 3 2. Wiring
More informationIntrusion Control Panels Quick Guide. May 2015
Intrusion Control Panels Quick Guide May 2015 Control Panels B Series Commercial Type Number B3512 B4512 B5512 Applications Type Residential, Small Commercial Residential, Small Commercial Residential,
More informationMetasys Integrator Northern Application
Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date 0900 APPLICATION NOTE Metasys Integrator Northern Application lntroduction Page *3 Application Details
More informationQuick Guide. FW ver: ( )
Quick Guide FW ver: 0.7.12 (12-08-2004) http://cdrs.try.hu Main Features: 2 independent Linecards External (Wall-mounted) DC12V power unit or 12V UPS In-built 6V battery charger with programmable charging
More informationVisorALARM-Manager Application Quick Guide. (Ver. 1.3) Dm 380-I. V:3.0
VisorALARM-Manager Application Quick Guide. (Ver. 1.3) Dm 380-I. V:3.0 1. Installation Requirements 1.1. PC Pentium III processor or higher. Minimum RAM memory: 128 Mbytes Operating system: Windows XP
More informationFOCUS 200 PLUS A CCC #: _ / / _ / ( _ ) _ - 35(/,0,1$5< -8/< Security Services CUSTOMER CONTROL UNIT TELEPHONE NUMBER:
CMP-DF2V1 7/01 Security Services SALES REPS: PLEASE FILL IN ALL WHITE AREAS. FOCUS 200 PLUS A CUSTOMER SYSTEM INVENTORY AND DATA ENTRY FORMS CCC #: _ / / _ / CUSTOMER CONTROL UNIT TELEPHONE NUMBER: ( _
More informationControl Panel DS7400XiV4-EXP
Control Panel DS7400XiV4-EXP Release Notes January 2005 Release Notes for Firmware Version 4.10 Trademarks Cobox is a trademark of Lantronix. 1.0 Remote Programming Compatibility Use RPS-INT L version
More informationInstallatIon GuIde scs-1r security ContRol ReCeIveR DMP Receiver Help Line
Installation Guide SCS-1R Security Control Receiver DMP Receiver Help Line Technical Service 1-888-436-7832 International 1-417-831-9362 After hours receiver emergencies 1-417-831-2866 Security Control
More informationDT6I Series 2 INTERROGATABLE 6 CHANNEL TALKING DIALLER. INSTALLATION MANUAL 2 nd EDITION.
INTERROGATABLE 6 CHANNEL TALKING DIALLER 2 nd EDITION. NEW FEATURES Simplified memory layout allowing for quicker and easier programming. Can now record individual messages for each of the 5 external alarm
More informationMOBA-NMS MOBA-NMS. Moser-Baer SA Export Division Geneva / Switzerland
MOBA-NMS MOBA-NMS 1 MOBA-NMS 1. Main Features 2. Device Configuration and Management 3. DTS Devices Support 4. MOBA-NMS - Web-Interface Comparison 2 MOBA-NMS 1. Main Features 3 MOBA-NMS - Main Features
More informationSuperBus 2000 Phone Interface/Voice Module Installation Instructions
SuperBus 2000 Module Installation Instructions Product summary The SuperBus 2000 (PIV) Module provides phone and voice functions for the Concord, Concord 4, and Concord Express (v4) panels. The PIV module
More informationCA-A480-A Elevator Controller. Reference & Installation Manual
CA-A480-A Elevator Controller Reference & Installation Manual TABLE OF CONTENTS INTRODUCTION.................................................................. 4 Introduction.............................................................................................
More informationSecurity System. Owner s Manual
Security System Owner s Manual What You Need to Know Before using this manual, you should become familiar with the Security System User s Guide. The User s Guide provides step by step instructions for
More informationBEETEL LANDLINE CORDLESS PHONE
BEETEL LANDLINE CORDLESS PHONE X47 X47 Features 2.4 GHz Analog 4 - Selectable Handset Ring Tones Any Key Answer Colors: Black/Metallic Black, Black/Metallic Blue, Black/Metallic Red, Black/Metallic Purple
More information1HWZRU;1;( Table of Contents. General Description...2. Ordering Information...2. Feature Definitions...3. Programming the LED Keypads...
HWZRU;;( Control/Communicator Installation Manual Table of Contents General Description... Ordering Information... Feature Definitions... Programming the LED Keypads... Programming the NX-E...9 Types of
More informationDriver Manual (Supplement to the FieldServer Instruction Manual) FS NCA
- Driver Manual (Supplement to the FieldServer Instruction Manual) FS-8700-98 NCA APPLICABILITY & EFFECTIVITY Effective for all systems manufactured after May 1, 2001 Driver Version: 1.00 Document Revision:
More informationINPUTS: Are 10K end of line monitored, with a response time of 300 ms. Alarm triggers SIREN, STROBE and REPORTING (depending on setup)
INPUTS: All inputs: Inputs 1 to 24: Tamper: Panic: Fire: Keyswitch: 16-18VAC: Are 10K end of line monitored, with a response time of 300 ms. Alarm triggers SIREN, STROBE and REPORTING (depending on setup)
More informationPROGRAMMING. Alarm Control Panel. SATEL sp. z o.o. ul. Budowlanych Gdańsk POLAND tel Firmware Version 1.
Firmware Version 1.07 1471 Alarm Control Panel PROGRAMMING versa_plus_p_en 04/16 SATEL sp. z o.o. ul. Budowlanych 66 80-298 Gdańsk POLAND tel. 58 320 94 00 www.satel.eu Before you start programming, please
More informationIDS1200 INSTALLER MANUAL. Summary of Operation 2 IDS1200 INSTALLER MANUAL - NO B ISSUED AUGUST 2002 VER 1.18
IDS12 INSTALLER MANUAL Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Away Arm Quick Stay Arm Quick Stay Arm & Go H old down [ 1] for 1 second H old down [ 5] for 1 second H old down [ 6] for
More informationKUUMIC OY DATA TRANSFER FALLBACK SWITCH KU113. Technical Reference
FALLBACK SWITCH Technical Reference CONTENTS 1. GENERAL...1 1.1. INTRODUCTION...1 1.1.1. Basic functions...1 1.2. TECHNICAL SPECIFICATIONS...3 1.2.1. CONNECTORS...3 1.2.2. LED INDICATORS...5 1.2.3. JUMPERS
More informationGSM communicator G09 (v.1.61) User Manual and Installation Guide. Draugystes g. 17, LT Kaunas
GSM communicator G09 (v.1.61) User Manual and Installation Guide Draugystes g. 17, LT-51229 Kaunas E-mail: info@trikdis.lt www.trikdis.lt Purpose of the document This document introduces the features of
More informationVISION 3 COMPACT GSM SPEECH DIALLER DESCRIPTION USER MANUAL
VISION 3 COMPACT GSM SPEECH DIALLER USER MANUAL DESCRIPTION is a GSM communicator, which uses the existing cellular network to provide reliable and cost effective communication for security systems. When
More informationMCM Electronics MCM Electronics MCM Electronics. The Icon Series. Installation and Programming Information. Icon 8 Version 5.0
MCM Electronics MCM Electronics MCM Electronics The Icon Series Installation and Programming Information Icon 8 Version 5.0 TABLE OF CONTENTS 1. 2. 3. Panel Hardware Page 2 Physical Layout. Inputs. Outputs.
More informationModules Programming Guide. paradox.com
Keypad Modules Annunciator Module Motion Detector Modules Zone Expansion Modules Access Control Module Voice Assisted Modules Accessory Modules Integration Module Internet Module Modules Programming Guide
More informationControl Panel. D9412GV4/D7412GV4/D7212GV4 v1.xx. Release Notes
Control Panel D9412GV4/D7412GV4/D7212GV4 v1.xx en Release Notes Control Panel Table of contents en 3 Table of contents 1 Introduction 4 1.1 About documentation 4 1.1.1 Bosch Security Systems, Inc. product
More informationLYNX Security System 3URJUDPPLQJ)RUP 6XPPDU\RI&RQQHFWLRQV. Features Q.E.D. programming for quick enrollment of devices.
Features Q.E.D. programming for quick enrollment of devices. LYNX Security System 3URJUDPPLQJ)RUP 6XPPDU\RI&RQQHFWLRQV ALPHA DRAFT June 5, 1998 OFF AWAY STAY AUX N8890 5/98 7$%/(2)&217(176 DATA FIELDS...
More informationECHO Process Instrumentation, Inc. Modbus RS485 Module. Operating Instructions. Version 1.0 June 2010
ECHO Process Instrumentation, Inc. Modbus RS485 Module Operating Instructions Version 1.0 June 2010 ECHO Process Instrumentation, Inc. PO Box 800 Shalimar, FL 32579 PH: 850-609-1300 FX: 850-651-4777 EM:
More informationRANGER 9000E DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL
RANGER 9000E DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS GENERAL DESCRIPTION... 2 STANDARD AND OPTIONAL PARTS LIST... 2 FEATURE DEFINITIONS... 3 TERMINAL DRAWING AND SPECIAL
More informationUse this manual with the following Analogue Fire control panels: FC200/S - 2 Loop Master panel with 2.5 A Switching power supply
SOFTWARE MANUAL Use this manual with the following Analogue Fire control panels: FC200-2 Loop Master panel with 4 A Linear power supply FC200/S - 2 Loop Master panel with 2.5 A Switching power supply FC200/SL
More informationControl Panel Solution 2000 / 3000
Control Panel Solution 2000 / 3000 en Quick Reference Guide Control Panel Table of contents en 3 Table of contents 1 Introduction 6 2 Programming 7 2.1 Alphanumeric Codepad Menu Programming 7 2.2 ICON
More informationPA2000 SERIES. USER MANUAL Rev. P CELL PHONE ENTRY SYSTEM. Platinum Access Systems Inc.
PA2000 SERIES CELL PHONE ENTRY SYSTEM USER MANUAL Rev. P Platinum Access Systems Inc. PRODUCT LINE PA2020 --- Cell Phone Entry System PA2022 --- Cell Phone Entry System (Flush Mount) PA2120 --- Cell Phone
More informationSIA Dialer Comms Task Format
MODEL 3000 / ACCESS 4000 Programmer s Manual - Rev 5.00 SIA Dialer Comms-31-1 SIA Dialer Comms Task Format Dialer Operation - SIA Dialer Format, Level 1. (V5 or later only) SIA Dialer format is used to
More informationXT30/XT50 PROGRAMMING PART 1. Slide 1. Slide 2. Slide 3. Objectives. XT30/XT50 Basic Training Programming- Part 1. Accessing the Programmer
Slide 1 XT30/XT50 Basic Training Programming- Part 1 Slide 2 Objectives After completing this course you will: 1) Understand how to prepare the panel for programming and how to access the built-in programmer.
More informationCIS-331 Exam 2 Fall 2015 Total of 105 Points Version 1
Version 1 1. (20 Points) Given the class A network address 117.0.0.0 will be divided into multiple subnets. a. (5 Points) How many bits will be necessary to address 4,000 subnets? b. (5 Points) What is
More informationLab 5: Access Control Training Station
Lab 5: Access Control Training Station Learning Objectives At the end of the lab, trainees should be able to: 1. Understand the functional block and hardware of an access control system. 2. Understand
More informationDNP 3.0 Communication User s Manual
MV Network management MV/LV substations remote monitoring Merlin Gerin Easergy Range Easergy FLAIR 200C DNP 3.0 Communication User s Manual Summary SUMMARY...3 SOFTWARE CONFIGURATION...4 DEVICE PROFILE
More informationModel HM-535 Power Supply Installation and Service Instructions
Model HM-535 Power Supply Installation and Service Instructions 430-535 0104 2004 Heritage MedCall, Inc SENTRY INSTALLATION & SERVICE INSTRUCTIONS POWER SUPPLY UNIT Model HM-535 IMPORTANT SAFETY INSTRUCTIONS
More informationALERT CONFIGURATION GUIDE SIA DRIVER
ALERT CONFIGURATION GUIDE SIA DRIVER 1) Installation A) SIA modem installation The SIA modem must be connected to a serial port on the PC (COM1, ) and plugged in an analog phone line. The modem being completely
More informationMicroStrain LXRS Wireless Base Station EEPROM Map
MicroStrain LXRS Wireless Base Station EEPROM Map EEPROM Address (Decimal) EEPROM Address (Hexidecimal) Nomenclature Valid Ranges Factory Init Value 0 0 Reserved - 65535-2 2 Reserved - 65535-4 4 Reserved
More informationQuick Reference Guide For Partner ACS R6 System Programming
System Programming From extension 10 or 11 (Any MLS display phone) dial Feature 00, then press the Left Intercom button 2 times to enter System Programming. The numbers in parentheses after the program
More informationQuick Reference Guide For Partner ACS R4 System Programming
System Programming From extension 10 or 11 (Any MLS display phone) dial Feature 00, then press the Left Intercom button 2 times to enter System Programming. The numbers in parentheses after the program
More information2 IDS LCD Keypad User Manual C Issued March 2009
2 3 4 Contents 1. Introduction to the IDS LCD Digital Keypad...8 2. Arming the Control Panel...8 2.1 Away Arming...8 2.1.1 How to Away Arm...8 2.1.2 Quick Away Arm Shortcut Key...8 2.2 Stay Arming...9
More informationVehicle DC-DC 120W User Guide DCX 3
Vehicle DC-DC 0W User Guide DCX Technical support: Email: tsupport@opussolutions.com Tel:- 949-87-00 x5 Package Contents DCX.0 Automotive ATX/ITX & AT intelligent DC-DC0W Power Supply - 4 pin ATX power
More informationIntroduction. Power and Supervision
Introduction The MLR2-DV multi-line DVACS compatible receiver is U.L.C. listed for commercial fire and burglary. The basic unit consists of a CPM2 Central Processor Module and a DVL2A DVACS Receiver Line
More information