Pressing the Print Button outputs a screenshot of the current screen to the printer. MICRO/I

Transcription

1 4 Print Button HG2G-S HG2G-5S HG2G-5F HG3G HG4G HG1F HG2F HG2S HG3F HG4F 4.1 How the Print Button is Used Outputs a screenshot to a printer or a memory card. Pressing the Print Button outputs a screenshot of the current screen to the printer. Printer 2011/1/11 HG2G-5F HG3G HG4G HG1F HG2F HG2S HG3F HG4F Refer to Chapter Connecting a Printer to on page 31-1 for compatible printers and instructions on how to connect one to the. Pressing the Print Button outputs a screenshot of the current screen to a memory card. SD Memory Card Image file HG2G-5F HG3G HG4G CF Card Image file HG2F HG3F HG4F This function is only supported by models that are equipped with a memory card interface. WindO/I-NV2 User s Manual -51

2 4.2 Print Button Configuration Procedure This section describes the configuration procedure for Print. 1 On the Home tab, in the Parts group, click, and then click Print Button. 2 Click a point on the edit screen where you wish to place the Print Button. 3 Double-click the dropped Print Button and a Properties dialog box will be displayed. 4 Change the settings on each tab as necessary. The Trigger Condition tab and Options tab only appear in Advanced mode. To switch to Advanced mode, click Advanced. -52 WindO/I-NV2 User s Manual

3 4.3 Properties of Print Button Dialog Box This section describes items and buttons in the Properties dialog box. General Tab Part Name Enter a name for the part. The maximum number is 20 characters. >>OFF Text, >>ON Text Applies the text entered in the Part Name field to the Text field under the OFF or ON fields on the Registration Text tab. This is used as the Registration Text when the button is OFF or ON. To specify the Registration Text to use when the button is ON, place a check in the Set by State check box on the Registration Text tab. If left unchecked, the same Registration Text assigned for the OFF state is displayed for the ON state as well. Output to Select where to direct the screenshot to. Printer: Outputs the screenshot to the printer connected to the. Memory Card *1 : Outputs the screenshot as a file to the memory card inserted in the. Files are output as follows: Series HG2G-5F HG3G/4G HG2F HG3F HG4F File format JPEG File name CAP***.JPG (***: date and time when file was output) Example: A file created at 1:50:25 on June 30, 2011 will be named CAP110630_15025.JPG. Bitmap CAP***.BMP (***: serial number from 001 to 999) File size Depends on image being displayed. 77,7 bytes 30,27 bytes 41,07 bytes Action Mode Select the behavior of the button from the following: Print Screen: For details about printers, refer to Chapter 31 Printer on page For details about memory cards, refer to Chapter 30 1 Memory Cards on page Outputs a screenshot of the current screen to the printer or the memory card. Cancel Printing: Cancels printout to the printer. *1 This is applicable for models with the memory card interface only. WindO/I-NV2 User s Manual -53

4 Print Time stamp Adds the date and time of printing to the screenshot before sending it to the printer. The date and time format depends on the language selected in Language. Language is available on the Project Details tab of the Project Settings dialog box. The display formats are shown below: Japanese: YYYY *2 /MM/DD HH:MM English: MM/DD/YYYY *2 HH:MM YYYY: year, MM: month, DD: day, HH: hour, MM: minute View Switching Method *3 Select how to display the ON/OFF status of the button. Button: Device: No Image: Pressing the button changes the drawing object displayed. The drawing objects assigned to the OFF and ON states are displayed when the value of the device is 0 and 1, respectively. Specifies the device used to switch the drawing object display. Click to display the Device Address Settings dialog box. For the device address configuration procedure, refer to Chapter Device Address Settings on page The button is not displayed on the screen. The button appears as a dashed line frame on the edit screen. Pressing the corresponding area on the activates the assigned function. If No Image is selected, the settings for View and Registration Text are disabled. Selecting Device in View Switching Method allows you to create an illuminated pushbutton. The illuminated pushbutton switches state (or image) according to ON or OFF state of the device address, allowing you to display the state of a device that is being operated. Example: When you set a host device 'M0' as Device in View Switching Method, if the value of M0 changes, the display image will switched according to the value of M0 even if the button is not pressed. Host device 0 OFF image: ON image: M0 View Switching Method (Device): M0 1 M0 These operations cannot be performed simultaneously. - Outputting to the memory card by pressing the Print Button. *1 - Outputting to the printer by pressing the Print Button. - Printing alarm logs *4 It may take some time to output screenshots when copying files using the USB Autorun function or a Key Button. The HG2G-5F, HG3G/4G cannot stop printing in the middle of a page, even when the print job is canceled. Print jobs after the current print job are canceled after the current page finishes printing. When printing a screenshot from the HG3F/4F using SII DPU-414 printer, the printed image will only include 320 pixels from the left edge of the screen. The maximum number of screenshots that can be captured (1 to 999) can be set in HG Special Registers LSD65. (Default: 99) *1 This is applicable for models with the memory card interface only. *2 Only last two digits of year shown on the HG1F/2F/2S/3F/4F. *3 Advanced mode only *4 HG2G-5F, HG3G/4G only -54 WindO/I-NV2 User s Manual

5 The methods to erase screenshot files saved on the memory card are as follows. To erase files during operation using parts, on the Memory Card tab on the Project Settings dialog box, select the Remove Files stored in Memory Card check box and the All Screenshot data check box, and then configure the trigger device. Assign that trigger device to a part. To erase files with WindO/I-NV2, click Clear on the Online tab, and then click Stored Data in Memory Card to open the Clear Data dialog box. Select the Screenshot Data check box and click OK. To erase files on the HG2G-5F and the HG3G/4G, select the files to erase with the System Menu File Manager, and then press DEL. WindO/I-NV2 User s Manual -55

6 View Tab Only Coordinates and Size can be configured when No Image is selected for View Switching Method on the General tab. Image Type Select the type of graphic to be used to represent the part. Standard: Picture: Uses the default graphics contained within WindO/I-NV2. Uses an image file saved in the Picture Manager. For details about image file restrictions, refer to Chapter Available Image Files on page Browse Select the type of graphic to be used to represent the part from the list of graphics. Click this button to display the View Browser or Picture Manager, depending on the setting for Image Type. OFF button, ON button Displays the graphic when ON or OFF. Clicking ON or OFF switches the image displayed on the View tab. OFF, ON Selects the color and pattern of the standard graphic when ON and OFF. Foreground Color, Background Color: Pattern: Selects the foreground and background colors of the standard graphic (color: 256 colors, monochrome: 16 shades). Click Color to display the Color Palette. Select a color from the Color Palette. Selects a pattern for the standard graphic. Click Pattern to display the Pattern Palette. Select a pattern from the Pattern Palette. -56 WindO/I-NV2 User s Manual

7 Flash Select this check box if flashing is desired (alternating ON and OFF) when a part is ON. Flash ON image OFF image Coordinates X, Y: Sets the display position of parts using coordinates. The X and Y coordinates of parts are defined relative to an origin at the top-left corner of the screen. X: 0 to (base screen horizontal size - 1) Y: 0 to (base screen vertical size - 1) Size (0, 0) Y X Screen Parts W, H: Sets width and height to define the size of parts. W: 20 to (base screen horizontal size) H: 20 to (base screen vertical size) Width Height Screen Parts WindO/I-NV2 User s Manual -57

8 Registration Text Tab These options can only be configured when Button or Device is selected for View Switching Method on the General tab. Font Selects the font used for displaying text from the following. Japanese, European, Chinese, Taiwanese, Korean, Central European, Baltic, Cyrillic, Windows, Stroke Can only be set when the Use Text Manager check box is cleared. The characters that can be displayed depend on the font. For details, refer to Chapter Available Text on page 2-6. Size Sets the character size ( to 12). Can only be set when Stroke is selected. Style Selects Regular or Bold for text style. Can only be set when Font is set to Japanese, European, Chinese, Taiwanese, Korean, Central European, Baltic or Cyrillic. Magnification W, H: Selects the magnification (0.5, 1 to *1 ) for text display. Can only be set when Font is set to Japanese, European, Chinese, Taiwanese, Korean, Central European, Baltic or Cyrillic. Align Text Vertical Selects text alignment in the vertical direction. Top, Center, Bottom For details, refer to Appendix 5 Text Alignment on page A-5. Align Text Horizontal Selects text alignment in the horizontal direction. Left, Center, Right, Center-Left For details, refer to Appendix 5 Text Alignment on page A-5. Set by State Select this check box if displaying different text when ON and OFF. Use Text Manager Select this check box if using the text registered in Text Manager for text display. *1 5 to 7 are only for the HG2G-S/-5S/-5F and HG3G/4G. -5 WindO/I-NV2 User s Manual

9 OFF, ON Text: Inputs characters to be displayed on parts. The maximum number is 3,750 characters. The characters that can be entered depend on the font selected using Font. For details, refer to Chapter Available Text on page 2-6. When entering Unicode characters click to display the Unicode Input dialog box. Enter the characters using the Unicode Input dialog box then click OK. Text ID: Text Color: Windows Font: Specifies the Text Manager ID No. (1 to 32000) when using the text registered in the Text Manager. Click to display Text Manager. Can only be set when the Use Text Manager check box is selected. Selects the color of the text displayed on the part (color: 256 colors, monochrome: 16 shades). Click Color to display the Color Palette. Select a color from the Color Palette. Sets the font to be used as the Windows Font. Select Windows using Font to display the current setting. To change the setting, click Change to display the Font dialog box. Can only be set when the Use Text Manager check box is cleared. For details, refer to Chapter 2 Windows Font on page WindO/I-NV2 User s Manual -59

10 Trigger Condition Tab The Trigger Condition tab is displayed in Advanced mode. Input Condition The Button is enabled and operational while the condition is satisfied. The Button is disabled and not operational while the condition is not satisfied. Example: When Trigger Type is While ON and Device is LM 0 While LM 0 is 0, the condition is not satisfied and the Button is not operational. While LM 0 is 1, the condition is satisfied and the Button is operational. Condition Not satisfied LM0: 0 Button Does not operate Condition Satisfied LM0: 1 Button Operates Trigger Type: Selects the condition to enable the Button from the following. Always enable: The Button is always enabled. Always enabled While ON: Enables the Button when the device value is 1. 1 Device value 0 Disabled Enabled Disabled Enabled Enabled Disabled -60 WindO/I-NV2 User s Manual

11 While OFF: Enables the Button when the device value is 0. 1 Device value 0 Enabled Disabled Enabled Disabled Disabled Enabled While satisfying the condition: Enables the Button when the condition is satisfied. Satisfied Condition Not satisfied Data Type: Device: Condition: Comment: Disabled Enabled Disabled Enabled Enabled Disabled Selects the type of data handled by the conditional expression for the input condition. This option can only be configured if While satisfying the condition is selected for Trigger Type. For details, refer to Chapter Available Data on page 2-2. Specifies the bit device or bit of the word device to serve as the input condition. This option can only be configured when While ON or While OFF is selected for Trigger Type. Click to display the Device Address Settings dialog box. For the device address configuration procedure, refer to Chapter Device Address Settings on page Specifies the conditional expression for the input condition. This option can only be configured when While satisfying the condition is selected for Trigger Type. Click to display the Trigger Condition Settings dialog box. For the conditional expression configuration procedure, refer to Chapter Setting Conditional Expressions on page Used for entering a comment for the input condition. The maximum number is 0 characters. Visible Condition *1 The Button is displayed while the condition is satisfied. The Button is hidden while the condition is not satisfied. Example: When Trigger Type is While ON and Device is LM 0 While LM 0 is 0, the condition is not satisfied and the Button is hidden. While LM 0 is 1, the condition is satisfied and the Button is displayed. Condition Not satisfied LM0: 0 Hide Condition Satisfied LM0: 1 Show When the ON delay check box is selected on the Options tab, if the button is hidden before the set time elapses from when the button begins to be pressed, the on delay is reset and the button does not operate. *1 HG2G-5F, HG3G/4G only WindO/I-NV2 User s Manual -61

12 Trigger Type: Selects the condition to display the Button from the following. Always visible: The Button is always displayed. Always show While ON: Displays the Button when the device value is 1. 1 Device value 0 Hide Show Hide Show Show Hide While OFF: Displays the Button when the device value is 0. 1 Device value 0 Show Hide Show Hide Hide Show While satisfying the condition: Displays the Button when the condition is satisfied. Satisfied Condition Not satisfied Hide Show Hide Show Show Hide Data Type: Device: Condition: Comment: Selects the type of data handled by the conditional expression for the visible condition. This option can only be configured if While satisfying the condition is selected for Trigger Type. For details, refer to Chapter Available Data on page 2-2. Specifies the bit device or bit of the word device to serve as the visible condition. This option can only be configured when While ON or While OFF is selected for Trigger Type. Click to display the Device Address Settings dialog box. For the device address configuration procedure, refer to Chapter Device Address Settings on page Specifies the conditional expression for the visible condition. This option can only be configured when While satisfying the condition is selected for Trigger Type. Click to display the Trigger Condition Settings dialog box. For the conditional expression configuration procedure, refer to Chapter Setting Conditional Expressions on page Used for entering a comment for the visible condition. The maximum number is 0 characters. -62 WindO/I-NV2 User s Manual

13 Options Tab The Options tab is displayed in Advanced mode. ON delay Select this check box to use the ON delay function. Time (x100 msec): Specify the length of time that the button must be held down before activation by selecting a value from 0 to 600 (units of 10 ms). The button activates after it is held down for a specified period of time. Button Does not operate Button Operates Hold down for 3 secs. This feature protects against mistaken operation by ensuring that the button will not be activated if touched accidentally. Security Groups Security groups are a security function for restricting the display and operation of parts. Setting the security group makes it possible to limit the display and operation in a similar way to using the Trigger Condition tab. Display: Input: Selects the security group for which display of parts is restricted. (Default: None) None: No security function is used. Administrator, Operator, Reader: Three security groups are set up by default. Click to display the Security Group Settings dialog box. If you create a security group on the Security Group Settings dialog box, you can select that created group. For details, refer to Chapter Adding and Editing Security Groups on page Selects the security group for which operation of parts is restricted. (Default: None) None: No security function is used. Administrator, Operator, Reader: Three security groups are set up by default. Click to display the Security Group Settings dialog box. If you create a security group on the Security Group Settings dialog box, you can select that created group. For details, refer to Chapter Adding and Editing Security Groups on page For details about security functions, refer to Chapter 23 User Accounts and the Security Function on page WindO/I-NV2 User s Manual -63

14 Example: If the user and security group for a part are set as follows: User Name User1 User2 User3 Security Group None Group A Group A, Group B Line Chart and Bar Chart Display: Group A 130 Numerical Display Display: None Button Display: Group A Input: Group B For User1, who is not included in the specified security group, Group A parts are not displayed. If the Password Screen is now opened and User2 logs in, Group A parts are displayed. 130 Password User Up Down A B C D E F CAN G H I J K L M N O P Q R S T U V W X CLR Y Z ENT User1 Group A parts are not displayed to User1 Open Password Screen, enter password, and switch to User2 User2 Group A parts are displayed to User2 Since the display security group is Group A, User2 can view the buttons. But since the input security group is Group B, User2 cannot operate the buttons. Suppose that the Password Screen is now opened and User3 logs in to the system. Group A buttons can be displayed, and Group B buttons can be operated. Password 130 User Up Down 130 A B C D E F CAN G H I J K L 130 M N O P Q R S T U V W X CLR Y Z ENT User2 Button Cannot operate For User2, Group A parts are displayed but Group B parts cannot be operated Open Password Screen, enter password, and switch to User3 User3 Button Can operate For User3, Group A parts are displayed and Group B parts can be operated No Touch Sound This function is to disable touch sounds only for specified parts when the makes touch sounds. Select this check box to display disable touch sounds for this part. To enable touch sounds on the, select the Enable Touch Sound check box under the System tab of the Project Settings dialog box. -64 WindO/I-NV2 User s Manual

15 Comment Tab The Comment tab is used to specify the parts arranged on the editing screen, and the popup text displayed when the mouse pointer is placed close to No., Name, or Type in the object list. When there are multiple parts of the same shape on the screen, this features makes it possible to distinguish between the parts without displaying the Properties dialog box for each part, by just mousing over the part. Description Used for entering comments about parts. The maximum number is 0 characters. Example: When mousing over the Button on the editing screen WindO/I-NV2 User s Manual -65