Getting Started With Beam Detailing Software V1.3 For ETABS SAP 2000 May 2016 Barcelona -Spain

Transcription

1 The Structural Engineering Services Platform for Innovation and Development Getting Started With Beam Detailing Software V1.3 For ETABS SAP 2000 May 2016 Barcelona -Spain i

2 Copyright Copyright SESPID, S.L.2015 All rights reserved. The program Beam Detailing, and all associated documentation are proprietary and copyrighted products. Ownership rest with the Structural Engineering Services Platform for innovation and Development SESPID,S.L. Unlicensed use of this programs or reproduction of documentation in any form, without prior written authorization from SESPID,S.L, is explicitly prohibited No part of this publication may be reproduced or distributed in any form or by any means, without the prior explicit written permission of the publisher. Further information Further support ii

3 DISCLAIMER CONSIDERABLE TIME, EFFORT AND EXPENSE HAVE GONE INTO THE DEVELOPMENT AND TESTING OF THIS SOFTWARE. HOWEVER, THE USER ACCEPTS AND UNDERSTANDS THAT NO WARRANTY IS EXPRESSED OR IMPLIED BY THE DEVELOPERS OR THE DISTRIBUTORS ON THE ACCURACY OR THE RELIABILITY OF THIS PRODUCT. THE USER MUST UNDERSTAND THE BASIC ASSUMPTIONS OF THE SOFTWARE, ARRANGEMENT OF THE REINFORCEMENT, DETAILING AND THE REINFORCEMENT ENVELOPES, CONDITIONS AND REQUIREMENT OF THE ACI 318, EC2-8, TS 500 and TDY 2007 THE DRAWINGS AND THE INFORMATION PRODUCED BY THE SOFTWARE MUST BE CHECKED BY A QUALIFIED AND ENGINEER OR ARCHITECT. THE ENGINEER OR THE ARCHITECT MUST INDEPENDENTLY VERIFY THE RESULTS AND TAKE PROFESSIONAL RESPONSIBILITY TO MODIFY OR USE THE PRODUCED INFORMATION. iii

4 Content: 1 Order Trial or Commercial License of BD Software Install BD software Activate the license of BD Software: Quick Start with BD software for ETABS Quick Start with BD software for SAP Tips iv

5 1. Order Trial or Commercial License of BD Software. To get a Trial License of BD-for ETABS and SAP2000, you have to go to the software page in SESPID website: click on Add to cart Trial version if you want to get a trial license valid for 30 days, then click on View Cart Commercial license Trial license Click on Proceed to Checkout as shown in the next figure: Fill your personal information and click on Place Order After clicking on Place Order, the next screen will appear: This is your License Order Number BD-820 Click here to download the software installer 5

6 2. Install BD software. The installer will be saved in the default downloading path: click on the file: If next message appeared, click on More Info button, and press on Run anyway Select the Installation folder path where Beam Detailing package will be extracted. Go to the installation folder (where the package has been installed): send a shortcut of BeamDetailing.exe to the desktop. In the installation folder open the folder BeamDetailier-ETABS and SAP 2000 These file will be used based on language version of your AutoCAD 6 Copy and paste these.dcl file to your AutoCAD support path.

7 The FOUR DCL files must be copied to AutoCAD support path, this path can be known by going to Options in AutoCAD as shown in the next figure: BD-V1.3-ES-English AutoCAD.fas file can be used when the language of AutoCAD functions is English BD-V1.3-ES-Espanol AutoCAD.fas file can be used when the language of AutoCAD functions is Spanish 7

8 3. Activate the license of BD Software: Double click on BeamDetailing.exe file (the shortcut you have sent to the desktop or in the main installation folder) Shortcut on Desktop Click on tools > activate >, Enter the activation keys that have been sent to your (check the junk and spam mail box). If you haven t received any activations keys by , then: The activation keys for Trial version are: Key 1: TRIALVERSION Key 2: TRIALVERSION Order NB: BD- Enter the order number of your license as an example 820- review page 5) You have to receive a message says: If the activation failed, please try couple of times and make sure you have deactivated your antivirus system and the windows firewall protection. For further help send us an to support@sespid.com 8

9 4. Quick Start with BD software for ETABS. We will Beam_Detailing software Manual Example to demonstrate the procedure you have to follow in order to carry out the RC beams detailing for any ETABS model: 1- Open the ETABS model BD-ETABS -Manual Model.EDB ( Located in the installation folder of Beam Detailing software: C:\BeamDetailing\Manual\Beam Detailing User Manual\ETBAS model 2- Select All the beam > Assign > Frame >Outputs stations > Min number stations You have to adjust the end offsets of the beam: Select all the element > Assign > Frame >End length offsets > Automatic From connectivity. 4- Run the model and design the beams using any design code (e.g. ACI ) 5- Define a new table set :Options > Show Modal Explorer > in the Model Explorer go to tables > add new table set The following tables must be selected in each of the following fields: Structural Layout : Joint coordinate > Joint coordinates Frame connectivity Column connectivity Beam connectivity Brace connectivity Shell connectivity Wall connectivity Definitions : Frame sections Frame sections Shell sections Shell sections Walls Assignments : Frame Assignments Frame assignments - Sections Frame assignments Local Axes Shell Assignments Shell assignments Sections Design : Concrete Design Concrete Beam Summary ACI

10 Note: In case some tables are not available to select, such as (Brace connectivity, Shell sections Walls, Frame assignments Local Axes, Shell assignments Sections).This means that the models doesn t have brace nor wall elements,or the local axes are not modified for any element in the whole model. In this case the user can continue without any problem. 6- Modify the table set units (must be in mm), any pair of units with mm is okay. 7- Select the floor in interest, the selection must include the nodes of the beams as well as all the supports (columns or shear walls) including the top and bottom nodes. Before exporting the tables, any non-structural elements in the model must be deselected as well as any steel beams. The best way to select the floor in interest is to go to Select > Stories > Select any story> click right > Show Selected Object Only > 10

11 8- Export the table sets to XML The export must be only for the selected floor. And save the XML file in a specific Path 9- Reading ETABS outputs and generating the input for Beam Detailer: Click on the shortcut of BeamDetailing.exe. A. Click on ETABS to work on ETABS generator B. Select a Path to save the output of (The Project Directory) C. Select the XML file that has been exported previously. D. Click on Generate 11

12 Generated files are: Different text files with different numbers (beam 01.txt, beam 02.txt etc.), each of these files corresponds to one of the detected beams in the selected floor. Plan_Generator.out: This files includes the geometry of the selected floor. Plan_Beam_Detailing.out: This file includes the design reinforcement for all the detected beams in the selected floor.in other words, this file include all the singles beams files in one file (Plan_Beam_Detailing includes beam 01.txt, beam 02.txt etc.) 4.1 Beam Detailer for ETABS and SAP 2000 To load the software: In AutoCAD menu bar go to > Tools > Auto Lisp > Load Application > (or just type APPLOAD in the command line) BD V1.3-ES.fas files can be found in the installation folder of Beam Detailing: C:\ BeamDetailing\BeamDetailier-ETABS and SAP 2000 For English Version of AutoCAD you have to use the English version of BD V1.3-ES.fas For Spanish Version of AutoCAD you have to use the Spanish version of BD V1.3- ES.fas 12

13 Type CSIBEAM in the AutoCAD command line>press Enter. After pressing Enter, the next user interface will appear. This interface is to select the language of the software.you can always reset the language by typing CSIBEAMPAR in the command line. If you select English, the next user interface of Beam_Detailer will appear: Beam Detailer software contains four applications: Plan Generator: Reads the output Plan_Generator.out, and can be used only to draw the plan layout of the selected floor in ETABS model. Beam Detailing: Reads any output of any single beam (beam 1, beam 2 etc.), and can be used only to perform the detailing for a single beam. Plan Beam Detailing: Reads the output Plan_Beam_Detailing.out, and can be used only to perform the detailing for all the beams in the entire floor. Max Beams Detailing: Reads the output Plan_Beam_Detailing.out, and can be used only to carry out the detailing for SIMILAR set of beams. The selected beams must have the same geometry and can be in different floor. 13

14 a) Plan Generator Application To have the geometry of the selected floor as a plan where you can identify the detected beams. 1- Select Plan Generator in the field 1, Plan generator application will be active. 2- The path of where the outputs of Beam Detailing Generator (BDG) are located, must be selected and pasted it in the path field. 3- Text file name must be (Plan_Generator) without the extension.out 4- Press OK. Names of the detected beams corresponds to the names of the different beams files that have been generated by Beam Detailing Generator, like example: In the element , the first number is the number of the text file (beam 12.txt) it means this element is a part of the mega beam 12. The second number 1381 corresponds to the unique name of the beam element in ETABS model. [In the case of SAP 2000 model the second number is the element s label]: b) Beam Detailing Application To carry out the detailing for one Beam Type CSIBEAM again in the command line to recall the user interface: Select Beam Detailing in the field 1, Beam Detailing application will be active. Refer to the User Manual for more detailed information about the inputs Text File Name is any beam text file. 14

15 c) Plan Detailing Application To carry out the detailing for the entire selected floor Write CSIBEAM again in the command line to recall the user interface. Select Plan Beam Detailing in the field 1, and use the Plan_Beam_Detailing text file. This application will repeat the same algorithm of Beam Detailing App for the entire floor (all the detected beams) d) Max beams detailing Application This application can be very useful to carry out the detailing for set of beams that have the same geometry and have more or less the same load. This App will carry out the detailing for the selected beams as they are one beam. The output of this App will be just one beam with reinforcement arrangement based on the envelopes diagrams of the whole beams (based on the maximum reinforcement). Text file name must be Plan_Beam_Detailing_file without the extension.out 5. Quick Start with BD software for SAP We will use the Beam_Detailing software Manual Example to demonstrate the procedure you have to follow in order to carry out the RC beams detailing for any SAP2000 model: 1- Open the SAP model BD-SAP -Manual Model.EDB ( Located in the installation folder of Beam Detailing: C:\BeamDetailing\Manual\Beam Detailing User Manual\SAP2000 model 1- Select All the beam > Assign > Frame >Outputs stations > Min number stations You have to adjust the end offsets of the beam: Select all the element > Assign > Frame >End length offsets > Automatic From connectivity. 3- Run the model and design the beams using any design code (e.g. ACI ) 4- Define a new table set :Options > Show Modal Explorer > in the Model Explorer go to tables > add new table set 5- Select the elements (The floor) in interest and make sure you have selected the top and the bottom joints of the supports (columns and shear walls), as shown in the next figure. 6- Change the units to (mm) by scrolling the unit bar at the bottom right corner. 15

16 Note: All the slab elements (horizontal shell elements) must be deselected before continue to the next step.this deselection is very important and especially in the case when SAP model has already a wall elements. This must should be done for all SAP models but not for ETABS models. 7- Keep on selecting the elements > Display > Show Tables > The following tables must be selected: Modeling definition: Property Definition : Frame Section Properties > Frame Section Properties01-General Area Section Properties > Area Section Properties. Connectivity Data : Joint Coordinate Joint Coordinates. Object Connectivity Connectivity Frame Connectivity Area Frame Assignments : Frame Item Assignments Frame Sections Assignments Frame Local Axes Assignments Area Assignments : Area Item Assignments Area Sections Assignments Design Data: Concrete Frame: Concrete Summary Data Concrete Design 2- Beam Summary Data ACI

17 Note: If there are some unavailable tables to select in the Tables window, the user can continue to the next step without any problems. 8- Press Ok, Then go to File > Display All Tables > In Text Editor W/No Splits as shown in.all the selected tables will be plotted in just one file, this file will be used later to carry out the beam detailing layouts. 9- Save the text file in a selected file: 17

18 Note: If the SAP 2000 output file has (,) instead of (.) all the (,) must be replaced by (.) before running the Beam Detailing Generator software. Repeat the step No 9 in the previous ETABS section, and select SAP 2000 in Beam Detailing Generator. Then you can carry out the detailing of the generated files, following the same process of ETABS models. 18

19 Tips 6. Tips This chapter helps the users to handle beam detailing package professionally: Beam detailing package is a tool to simplify the interaction between structural analysis software and the operation of generating the layouts of reinforced concrete beams. Beam Detailing as any other tool still have some limitations, we have done our best to make it simple, flexible and powerful. We really recommend the new users to read this document and understand the basics and assumptions of Beam Detailing. Produced information and drawings must be reviewed carefully by a qualified engineer or architect. Do not use the edit area to mesh the shear wall element, use the normal mesh option. Make sure you have exported the results in (mm) units. Beam Detailing understand each intersection joint in the analytical model developed via (ETABS, SAP 2000 or RISA 3D), as a support between two spans. For this reason try to divide the beams element only at the columns or at the shear walls. Do not overlap the beam elements with shear elements. Do not insert columns elements at the edge of wall element, the connection in this case must be beam to wall. Don t forget to deselect all the nonstructural element from the model before exporting the results, in the same time remain on the joints between elements. Export each floor individually Remember always to select the upper and the lower nodes of element in the case of the first floor you have to select the base nodes. For SAP 2000 models, don t forget to deselect all the slab elements before exporting the tables. Do not export any unnecessary tables of any model [ETABS or SAP 2000]. Local axes direction of beam elements must be reviewed by the user, especially for the case of a beam with just one span. In order to identify the end supports. Try to avoid switching the local axis (1) of continuous beams. It s always better to model the beams in the same direction. Beam Detailing Generator for ETABS and SAP 2000 assumes the columns and beams section have t3 t2 dimension. Any section that has no t3- t2 dimension Beam detailing Generator will not be able to run. In this case the user has to fill these values manually in the exported file. 19