English ETERNUS CS800 S3. NetBackup OST Guide

Transcription

1 English ETERNUS CS800 S3 NetBackup OST Guide Edition April 2012

2 Comments Suggestions Corrections The User Documentation Department would like to know your opinion on this manual. Your feedback helps us to optimize our documentation to suit your individual needs. Feel free to send us your comments by to: Certified documentation according to DIN EN ISO 9001:2008 To ensure a consistently high quality standard and user-friendliness, this documentation was created to meet the regulations of a quality management system which complies with the requirements of the standard DIN EN ISO 9001:2008. cognitas. Gesellschaft für Technik-Dokumentation mbh Copyright and Trademarks Copyright Fujitsu Technology Solutions GmbH All rights reserved. Delivery subject to availability; right of technical modifications reserved. This document includes trademarks and copyrights of Quantum Corporation. All rights reserved. Microsoft, Microsoft Windows, and Windows Server are U.S. registered trademarks of Microsoft Corporation. Linux is a registered trademark of Linus Torvalds. Fujitsu and the Fujitsu Logo are trademarks of Fujitsu Limited. All hardware and software names used are trademarks of their respective manufacturers. This manual is printed on paper treated with chlorine-free bleach.

3 Contents Preface NetBackup OST Guide Introduction Installing the OST Plug-in Configuring the ETERNUS CS800 S Configuring OST Authentication Configuring Storage Servers Configuring Logical Storage Units Configuring Symantec NetBackup (Media Server) NetBackup Configuration Registering the Storage Server with NetBackup Discovering Logical Storage Units Using the Storage Server Configuration Wizard Configuring Disk Pools and Storage Units in NetBackup Initiating an OST Backup Performing Synthetic Full Backups Initiating an OST Optimized Duplication Replication Channel for OST Enabling Verbose Logging OST Plug-in Log Configuring OST Path to Tape Verifying Prerequisites Configuring Physical Tape Libraries Configuring NetBackup OST for Path to Tape Running a Duplication to Tape Configuring ETERNUS CS800 S3 Accent Enabling or Disabling Accent on the ETERNUS CS800 S Enabling or Disabling ETERNUS CS800 S3 Accent on the Media Server Maximum Number of Jobs When Using ETERNUS CS800 S3 Accent U41852-J-Z

4 Contents U41852-J-Z

5 Preface ETERNUS CS800 NetBackup OST Guide provides information about configurations for usage of OST Optimized Replication with NetBackup. Additionally OST Path to Tape configurations related to NetBackup are described. Audience This guide is written for ETERNUS CS800 S3 operators and system administrators. Document Organization The following formats indicate important information: I Note emphasizes important information related to the main topic. V Caution indicates potential hazards to equipment or data. W Warning indicates potential hazards to personal safety. Related Documents The following documents are also available for ETERNUS CS800 S3 systems: Document No. Document Title Document Description A26361-F1452- Safety Notes and Regulations Z N19 U41840-J-Z ETERNUS CS800 S3 User s Guide Lists Fujitsu s general safety and regulatory information. Provides information about the ETERNUS CS800 S3 system, installation and operation. U41852-J-Z

6 Preface Document No. Document Title Document Description U41841-J-Z ETERNUS CS800 S3 Command Line Interface (CLI) Guide Provides information about the command line interface. U41853-J-Z BackupExec OST Guide Provides information about configurations for usage of OST Optimized Replication with Backup Exec. ETERNUS CS800 S3 Online Help Provides task-oriented information about a running system. Support and Help Where to Find Information Resource Address Product information and documentation ETERNUS CS800 manuals Release notes Downloads and Software patches Select Storage ETERNUS CS. Technical Support The Support section of the Fujitsu Technology Solutions web site provides links with contact information and information about available support programs: If you have an active support agreement, you may contact your service provider. If you do not have an active support agreement, contact your Fujitsu Technology Solutions sales representative to purchase a service contract or updates. 2 U41852-J-Z

7 Preface Customer Service Resource Address Education and training Fujitsu Technology Solutions Mies-van-der-Rohe-Str. 8, Munich, Germany Support phone / fax / Your Comments Your suggestions will help us continue to improve the accuracy, organization, and overall quality of the user publications. Please send your opinion of this document to: manuals@ts.fujtsu.com If you have issues, comments, or questions about specific information or procedures, please include the title and, if available, the part number, the page numbers, and any other details that will help us locate the subject you are addressing. Fujitsu Home Page Visit the home page of Fujitsu Technology Solutions at: Fujitsu Compliance Link See the compliance link of Fujitsu Technology Solutions at: To get information about the storage component, select "Storage Products > ETERNUX DX > ETERNUS DX80". To get information of the server component, select: "Industry Standard Servers > Rack Server > Primergy RX300 S6. Worldwide End-User Product Warranty For information the Fujitsu Worldwide end-user standard limited product warranty look at: U41852-J-Z

8 Preface 4 U41852-J-Z

9 NetBackup OST Guide Introduction I This guide is for ETERNUS CS800 S Software. V CAUTION! If you have previously used Active Directory (CIFS share) to perform authentication between an OST Plug-in and a ETERNUS CS800 S3 running 1.4.x or earlier, note that this has changed. The new method of OST Plug-in authentication between OST Plug-in 2.3 and later and ETERNUS CS800 S3 2.x and later DOES NOT USE Active Directory authentication. Instead, you must add new OST user credentials on the ETERNUS CS800 S3 and the media server. For instructions, see "Configuring OST Authentication" on page 7. Symantec NetBackup OST (Open Storage) allows NetBackup to seamlessly integrate with a ETERNUS CS800 S3 disk backup system. Once installed and configured, NetBackup can manage the backups through the ETERNUS CS800 S3 and take advantage of the system s capabilities such as data deduplication and replication. Installing and configuring the ETERNUS CS800 S3 and NetBackup OST for operation consists of the following major steps. See the following sections for detailed instructions for completing each step: 1. Installing the OST Plug-in 2. Configuring the ETERNUS CS800 S3 3. Configuring Symantec NetBackup (Media Server) 4. Registering the Storage Server with NetBackup 5. Configuring Disk Pools and Storage Units in NetBackup 6. Initiating an OST Optimized Duplication 7. Configuring OST Path to Tape 8. Configuring ETERNUS CS800 S3 Accent U41852-J-Z

10 Installing the OST Plug-in NetBackup OST Guide Installing the OST Plug-in I For Replication (Optimized Duplication): the OST Client Plug-in must be installed on the media server configured with NetBackup or later, or NetBackup 7.x. I For OST Path To Tape (Direct To Tape) - NetBackup or later, or NetBackup 7.x. The OST Client Plug-in is provided as follows: On a data medium shipped together with the ETERNUS CS800 S3 system. A README file is included which contains detailed instructions about the installation. At the Fujitsu Technology Solutions support pages under: The right OST plug-in variant depends on the operating system of your Media Server. To download the correct version of the OST Plug-in from the support pages: 1. On the system remote management console, navigate to the Configuration > OST > OST Client Plug-In page. 2. Click Client Plug-In Download. 3. Select Driver & Downloads. In the next window fill in the following values in the section Select Product. 1. Storage solutions 2. ETERNUS CS/CentricStor 3. ETERNUS CS800 You will get a list of supported operating systems. Select the desired one. Make sure to download the correct OST Plug-in for your version of NetBackup (6.5.x or 7.x) and for the operating system installed on the NetBackup media server. In the OST Plug-in zip-file you will find a README file, which contains the installation procedure for the OST Plug-in. This procedure is different for each NetBackup media server operating system platform. Follow the instructions to install the OST Plug-in on the NetBackup media server. I When multiple hosts are using a single system, you can distribute the load by dividing the hosts into groups. For more information, see the section Performance Tuning in the README file. I By default, the OST Plug-in for Windows is installed in the C:\Program Files\Symantec\NetBackup\ directory. 6 U41852-J-Z

11 NetBackup OST Guide Configuring the ETERNUS CS800 S3 Configuring the ETERNUS CS800 S3 You must configure storage servers and logical storage units on the ETERNUS CS800 S3 remote management console before you configure NetBackup. See the following sections to configure the ETERNUS CS800 S3 for OST. Configuring the ETERNUS CS800 S3 consists of the following major steps. See the following subsections for detailed instructions for completing each step: Configuring OST Authentication Configuring Storage Servers Configuring Logical Storage Units I You can also use the OST Wizard to configure the ETERNUS CS800 S3 for OST. Refer to the User s Guide for ETERNUS CS800 S3. Configuring OST Authentication To authenticate the OST storage servers on a media server, you must create OST user credentials. V CAUTION! If you have upgraded to ETERNUS CS800 S Software from a version released prior to 2.0, you must add new OST credentials to the ETERNUS CS800 S3 to continue using OST. Shut down the NetBackup services. Then perform the procedure below, making sure to use the same username and password that were used to register the existing OST devices. Finally, start the NetBackup services. To create OST user credentials: 1. Log on to the ETERNUS CS800 S3 remote management console. 2. Navigate to the Configuration > OST > Manage Users page (see Figure 1). U41852-J-Z

12 Configuring the ETERNUS CS800 S3 NetBackup OST Guide Figure 1: Manage Users Page 3. Click Add. 4. Specify the Username and Password that will be used to authenticate the storage servers on the media server. I For username, alphanumeric characters are allowed, as well as underscores ( _ ) and hyphens ( - ). For password, alphanumeric characters are allowed, as well as the following special: ` # $ % ^ & * ( ) - _ = + [ { ] } \ ; : ', <. > /? V CAUTION! In ETERNUS CS800 S3 software, you no longer should include a domain name as part of the username. If you have upgraded from ETERNUS CS800 S3 1.4.x Software, create a simple username and password using the rules noted above, and then provide the same credentials on the media server (see "Registering the Storage Server with NetBackup" on page 19). 5. Click Apply. 6. In NetBackup, add credentials for the storage server, making sure to use the same OST username and password you entered on the ETERNUS CS800 S3. For more information, see "Registering the Storage Server with NetBackup" on page 19. Configuring Storage Servers To configure storage servers: 1. Log on to the ETERNUS CS800 S3 remote management console. 2. Navigate to the Configuration > OST > Storage Servers page (see Figure 2). 8 U41852-J-Z

13 NetBackup OST Guide Configuring the ETERNUS CS800 S3 Figure 2: Storage Servers Page Use the Storage Server page to perform the following tasks. See the following subsections for detailed instructions for completing each task: "Adding a Storage Server" "Editing a Storage Server" "Deleting a Storage Server" I It is recommended to create a different storage server for each NetBackup domain (master server plus associated media servers). This segregates data so a NetBackup administrator cannot accidentally modify or remove backup images belonging to another domain. Adding a Storage Server To add a storage server: I You can create up to 100 storage servers. 1. On the Storage Servers page, click Add. The Add Storage Server page displays (see Figure 3). U41852-J-Z

14 Configuring the ETERNUS CS800 S3 NetBackup OST Guide Figure 3: Add Storage Server Page 2. Under Add Storage Server, enter information about the storage server: Name - Enter the name of the storage server. V CAUTION! Do not use an underscore ( _ ) in the name of the storage server. I Storage server names must be unique and not used again on other ETERNUS CS800 S3 systems. Description - (Optional) Enter a brief description of the storage server. Max Connections - Enter the maximum number of connections allowed to the storage server (3 to 65536). The maximum connections indicate the number of NetBackup jobs that can connect to the storage server. I It is recommended to set this value to 300 so that media servers never run out of storage server connections. 3. Under Logical Storage Unit, enter information about the LSU to add to the new storage server: I For best performance, an LSU should not contain more than 250 backup images. If you will need to store more than 250 backup images on the system, you should create additional storage servers and LSUs. 10 U41852-J-Z

15 NetBackup OST Guide Configuring the ETERNUS CS800 S3 Available Capacity - (Recommended for best performance) Select this option to add an LSU that uses the available capacity on the system. You cannot add an available capacity LSU to a storage server that already contains an LSU. Also, if you add an available capacity LSU to a storage server, you cannot add additional LSUs to that same storage server. I After you add an LSU that uses the Available Capacity option, you cannot change the LSU to use the Specific Capacity option. Instead, you must delete the LSU, then add a new LSU and choose the Specific Capacity option (see "Deleting an LSU" on page 15). Specific Capacity - Select this option to specify the physical capacity of the LSU, and then enter the following information. LSU Name - Enter the name of the LSU. Physical Capacity - Enter the physical capacity of the LSU (1 to GB). I It is recommended to set LSUs to maximum size ( GB). 4. (Optional) In the Description box, enter a brief description of the LSU. 5. Click Apply. Editing a Storage Server To edit a storage server: 1. On the Storage Servers page, select the storage server and click Edit. 2. Enter information about the storage server: I If you are editing a storage server, only the Description and Max Connections options can be changed. Description - (Optional) Enter a brief description of the storage server. Max Connections - Enter the maximum number of connections allowed to the storage server (3 to 65536). The maximum connections indicate the number of NetBackup jobs that can connect to the storage server. The maximum number of connections cannot be changed if the storage server has more than zero currently active connections. The number of active connections is displayed on the OST page (see Figure 2). I It is recommended that this value is set to 300 so that media servers never run out of storage server connections. 3. Click Apply. U41852-J-Z

16 Configuring the ETERNUS CS800 S3 NetBackup OST Guide Deleting a Storage Server To delete a storage server: 1. On the Storage Servers page, select the storage server and click Delete. You cannot delete a storage server if it has more than zero currently active connections. The number of active connections is displayed on the OST page (see Figure 2). Also, you cannot delete a storage server if it contains LSUs. Before deleting the storage server, you must first delete any LSUs it contains (see "Deleting an LSU" on page 15). I You can select multiple storage servers to delete at once. 2. Click Yes. I In order to remove the storage server from the ETERNUS CS800 S3 remote management console, you must remove the storage unit and disk pool from NetBackup. See the NetBackup System Administrator s Guide for details. After successfully deleting the storage units, disk pools and the corresponding storage server from NetBackup, the connection between NetBackup and the storage server remains open for a grace period of about ten minutes. After the grace period, the active connection count drops to zero. Configuring Logical Storage Units To configure logical storage units: 1. Log on to the ETERNUS CS800 S3 remote management console. 2. Navigate to the Configuration > OST > LSU page (see Figure 4). 12 U41852-J-Z

17 NetBackup OST Guide Configuring the ETERNUS CS800 S3 Figure 4: LSU Page Use the LSU page to perform the following tasks. See the following subsections for detailed instructions for completing each task: "Adding an LSU" "Editing an LSU" "Deleting an LSU" Adding an LSU To add an LSU to a storage server: 1. On the LSU page, click Add. The Add Logical Storage Unit page displays (see Figure 5). U41852-J-Z

18 Configuring the ETERNUS CS800 S3 NetBackup OST Guide Figure 5: Add Logical Storage Unit Page 2. Enter information about the LSU. I For best performance, an LSU should not contain more than 250 backup images. If you will need to store more than 250 backup images on the system, you should create additional storage servers and LSUs. Storage Server - Select the storage server that will contain the new LSU. Available Capacity - (Recommended for best performance) Select this option to add an LSU that uses the available capacity on the system. I You cannot add an available capacity LSU to a storage server that already contains an LSU. Also, if you add an available capacity LSU to a storage server, you cannot add additional LSUs to that same storage server. I After you add an LSU that uses the Available Capacity option, you cannot change the LSU to use the Specific Capacity option. Instead, you must delete the LSU, then add a new LSU and choose the Specific Capacity option (see "Deleting an LSU" on page 15). Specific Capacity - Select this option to specify the physical capacity of the LSU, and then enter the following information. LSU Name - Enter the name of the LSU. Physical Capacity - Enter the physical capacity of the LSU (1 to GB). I It is recommended to set LSUs to maximum size ( GB). 3. (Optional) In the Description box, enter a brief description of the LSU. 14 U41852-J-Z

19 NetBackup OST Guide Configuring the ETERNUS CS800 S3 4. Click Apply. Editing an LSU Deleting an LSU To edit an LSU: 1. On the LSU page, select the LSU and click Edit. 2. (Optional) Select a different LSU to edit in the Name drop-down box. 3. Enter information about the LSU: I If you are editing an available capacity LSU, only the Description option can be changed. If you are editing a specific capacity LSU, only the Physical Capacity and Description options can be changed. Physical Capacity - (Specific capacity LSUs only) Enter the physical capacity of the LSU (1 to GB). The physical capacity cannot be changed if the LSU has more than zero currently active connections. The number of active connections is displayed on the LSU page (see Figure 4). Description - (Optional) Enter a brief description of the LSU. 4. Click Apply. To delete an LSU: 1. On the LSU page, select the LSU. You cannot delete an LSU if it has more than zero currently active connections. The number of active connections is displayed on the LSU page (see Figure 4). I You can select multiple LSUs to delete at once. 2. (Optional) Select the Force Delete LSU check box to delete LSUs that are not empty. Normally, you cannot delete an LSU if it contains existing backup images. If for some reason you cannot remove files from the LSU, selecting the Force Delete LSU check box allows you to delete the LSU even though it is not empty. 3. Click Yes. U41852-J-Z

20 Configuring Symantec NetBackup (Media Server) NetBackup OST Guide Configuring Symantec NetBackup (Media Server) See the NetBackup System Administrator s Guide for information about NetBackup installation and basic configuration. Also, see the NetBackup Shared Storage Guide before proceeding further. I This section is for configuring NetBackup on Windows. To configure NetBackup on Linux, see."registering the Storage Server with NetBackup" on page 19 V CAUTION! You MUST have all NetBackup or later, or 7.x, updates applied (including the Java client) before continuing with configuration. If you are planning to use OST path to tape, you must have all NetBackup or later, or 7.x, updates applied. NetBackup Configuration In addition to the basic configuration of the NetBackup media server, perform the following procedures in the Windows 2003 or 2008 (32-bit and 64-bit) operating system: "Add Access Control to the Windows Operating System" "Change the Access Rights for NetBackup" Add Access Control to the Windows Operating System For the OST windows plug-in to operate correctly, you must add the access control users to the Windows operating system. 1. Create a user on the NetBackup Windows server. 2. Open Computer Management and under System Tools, expand Local Users and Groups. 3. Right click and select New User... (see Figure 6). 4. Add one of the users that has access to the ETERNUS CS800 S3 system. Users with access to the ETERNUS CS800 S3 system can be found from the ETERNUS CS800 S3 remote management interface under OST> Manage Users. 16 U41852-J-Z

21 NetBackup OST Guide Configuring Symantec NetBackup (Media Server) Figure 6: Adding a new User Change the Access Rights for NetBackup You must change the access rights to run the following services for NetBackup under the ETERNUS CS800 S3 system access group member account rather than the system account: NetBackup Device Manager NetBackup Client Service NetBackup Remote Manager and Monitor Service To login with administrative credentials (see Figure 7): 1. Open the Services window. 2. Right-click the service and select Properties. 3. In the Properties window of the service, click Log on tab. 4. Select This Account Option and enter the administrative login name and password. U41852-J-Z

22 Configuring Symantec NetBackup (Media Server) NetBackup OST Guide 5. Click OK and restart the service to login with the new credentials. Figure 7: Changing the Access Rights for NetBackup 18 U41852-J-Z

23 NetBackup OST Guide Registering the Storage Server with NetBackup Registering the Storage Server with NetBackup Discovering Logical Storage Units After the OST Plug-in is installed and configured on the NetBackup media server, you must register the storage servers with NetBackup by defining them on the media server. You must complete this process on every media server that will access the storage servers on the ETERNUS CS800 S3. You can configure multiple media servers to use the same storage servers as long as the OST Plug-in is installed on each media server. To register a storage server, first define it using the nbdevconfig command, and then provide credentials using the tpconfig command. I For NetBackup 7.x, you can perform this process using the Storage Server Configuration Wizard instead of the CLI commands (see "Using the Storage Server Configuration Wizard" on page 23). I The storage server argument passed to the nbdevconfig command should be in the form of <name_ip>, where the name is the name of storage server to be registered and IP is the IP address of the ETERNUS CS800 S3. If the ETERNUS CS800 S3 is configured with multiple network interfaces (see the User s Guide for ETERNUS CS800 S3 system) the IP will be the network interface used for data. This is also applicable when registering storage servers on a Windows platform. I If the IP address of the ETERNUS CS800 S3 or media server changes at any time after registering the storage servers (for example, due to switch changes), you must delete the existing storage servers and disk pools on the media server, and then register the storage servers again using the procedures below. You must take these actions on all media servers that access the storage servers. Registering the Storage Server on Windows Platforms via CLI I The procedures in this section assume NetBackup is installed in the default location on the C: drive. If you installed Netbackup in a different drive or location, modify the commands with the correct path. I For complete usage information about these commands, refer to NetBackup Commands for Windows. To register the storage server on a Windows NetBackup media server platform, perform the following steps: U41852-J-Z

24 Registering the Storage Server with NetBackup NetBackup OST Guide 1. Add the storage server to NetBackup: C:\Program Files\Veritas\NetBackup\bin\admincmd\nbdevconfig -creatests - storage_server <storage_server_name_ip> -stype FTS -media_server <media_servername> -st 9 Example: Add a storage server by name nbustorageserver at IP address and a media server by name nbumedia. C:\Program Files\Veritas\NetBackup\bin\admincmd\nbdevconfig -creatests - storage_server nbustorageserver_ stype FTS -media_server nbumedia -st 9 I When specifying the -storage_server variable (passed to the nbdevconfig command), you must include both the name of the storage server (defined in the ETERNUS CS800 S3 storage server configuration) and the IP address of the ETERNUS CS800 S3 separated by an underscore. For example: nbustorageserver_ I If the ETERNUS CS800 S3 is configured with multiple network interfaces (see the User s Guide for your ETERNUS CS800 S3 system), the IP address of the interface enabled for data should be used to register the storage server I A message from the prompt indicates that the storage server was added successfully. Otherwise, an error message is displayed. 2. Specify the credentials of the storage server: C:\Program Files\Veritas\Volmgr\bin\tpconfig -add -storage_server <storageserver_ip> -stype FTS -sts_user_id <username> -password <password> Example: Add credentials for storage server nbustorageserver. C:\Program Files\Veritas\Volmgr\bin\tpconfig -add -storage_server nbustorageserver_ stype FTS -sts_user_id ostuser -password password V CAUTION! The username and password must be the same as the OST user credentials created on the ETERNUS CS800 S3 remote management console (see "Configuring OST Authentication" on page 7). I When specifying the -storage_server variable, you must include both the name of the storage server (defined in the storage server configuration) and the IP address of the ETERNUS CS800 S3 separated by an underscore. For example: nbustorageserver_ I No message displays if the credentials are added successfully. However, an error message displays if the credentials are incorrect. 20 U41852-J-Z

25 NetBackup OST Guide Registering the Storage Server with NetBackup Verifying the LSU Discovery After you have registered the storage server, verify the discovery of LSUs by performing the following step: 1. From the command line on the master server, type: <install path>\netbackup\bin\admincmd\nbdevconfig previewdv -stype FTS storage_servers <storageserver_ip> Example: Verify LSU discovery for storage server nbustorageserver. C:\Program Files\Veritas\NetBackup\bin\admincmd\nbdevconfig -previewdv - stype FTS -storage_servers nbustorageserver_ I When specifying the -storage_server variable, you must include both the name of the storage server (defined in the ETERNUS CS800 S3 storage server configuration) and the IP address of the ETERNUS CS800 S3 separated by an underscore. Storage server names are case sensitive on all platforms including Windows. For example: nbustorageserver_ This will show if the storage server has been discovered by NetBackup and if the password is correct. Registering the Storage Server on Unix/Linux Platforms I For complete usage information about these commands, refer to NetBackup Commands for UNIX and Linux. To register the storage server on Solaris or Linux NetBackup media server platforms: 1. Add the storage server to NetBackup by executing the following command on the NetBackup media server as root: /usr/openv/netbackup/bin/admincmd/nbdevconfig -creatests -storage_server <storageserver_ip> -stype FTS -media_server <media_servername> -st 9 Example: adding a storage server by name nbustorageserver and a media server by name nbumedia. /usr/openv/netbackup/bin/admincmd/nbdevconfig -creatests -storage_server nbustorageserver_ stype FTS -media_server nbumedia -st 9 I When specifying the -storage_server variable (passed to the nbdevconfig command), you must include both the name of the storage server (defined in the storage server configuration) and the IP address of the ETERNUS CS800 S3 separated by an underscore. For example: nbustorageserver_ U41852-J-Z

26 Registering the Storage Server with NetBackup NetBackup OST Guide I If the ETERNUS CS800 S3 is configured with multiple network interfaces (see the User s Guide for your ETERNUS CS800 S3 system), the IP address of the interface enabled for data should be used to register the storage server. I A message from the prompt indicates that the storage server was added successfully. Otherwise, an error message is displayed. 2. Specify the credentials of the storage server: /usr/openv/volmgr/bin/tpconfig -add -storage_server <storageserver_ip> -stype FTS -sts_user_id <username> -password <password> Example: Adding credentials for storage server nbustorageserver. /usr/openv/volmgr/bin/tpconfig -add -storage_server nbustorageserver_ stype FTS -sts_user_id ostuser -password password V CAUTION! The username and password must be the same as the OST user credentials created on the ETERNUS CS800 S3 remote management console (see "Configuring OST Authentication" on page 7). I When specifying the -storage_server variable, you must include both the name of the storage server and the IP address of the ETERNUS CS800 S3 separated by an underscore. For example:nbustorageserver_ I No message displays if the credentials are added successfully. But an error message displays if the credentials are incorrect. Verifying the LSU Discovery After you have registered the storage server, verify the discovery of LSUs: 1. From the command line on the master server, type: /usr/openv/netbackup/bin/admincmd/nbdevconfig previewdv stype FTS storage_servers <storageserver_ip> Example: Verify LSU discovery for storage server nbustorageserver. /usr/openv/netbackup/bin/admincmd/nbdevconfig previewdv stype FTS storage_servers nbustorageserver_ I When specifying the -storage_server variable, you must include both the name of the storage server (defined in the ETERNUS CS800 S3 storage server configuration) and the IP address of the ETERNUS CS800 S3 separated by an underscore. For example: nbustorageserver_ This will show if the LSU has been discovered by NetBackup and if the password is correct. 22 U41852-J-Z

27 NetBackup OST Guide Registering the Storage Server with NetBackup Using the Storage Server Configuration Wizard For NetBackup 7.x, you can use the Storage Server Configuration Wizard to register storage servers. I The appearance of screens may vary depending on the version of NetBackup used. (NetBackup 7.0 is shown.) To register storage servers: 1. Start NetBackup: In Windows, double-click the NetBackup Administration Console icon. In Solaris and Linux, run the following command: /usr/openv/netbackup/bin/jnbsa & The NetBackup Administration Console displays (see Figure 8). U41852-J-Z

28 Registering the Storage Server with NetBackup NetBackup OST Guide Figure 8: NetBackup Administration Console 2. In the Details pane (on the right), click Configure Disk Storage Servers. The Storage Server Configuration Wizard displays (see Figure 9). 24 U41852-J-Z

29 NetBackup OST Guide Registering the Storage Server with NetBackup Figure 9: Storage Server Configuration Wizard 3. Click Next. The Add Storage Server Type window displays (see Figure 10). U41852-J-Z

30 Registering the Storage Server with NetBackup NetBackup OST Guide Figure 10: Add Storage Server Type 4. Select OpenStorage in the list, and then click Next. The Add Storage Server Details window displays (see Figure 11). 26 U41852-J-Z

31 NetBackup OST Guide Registering the Storage Server with NetBackup Figure 11: Add Storage Server Details 5. Enter the following information about the storage server: Storage server type - Enter FTS. Storage server name - The name of the storage server in the format <storageserver_ip>. I When specifying the Storage server name, you must include both the name and IP address of the storage server separated by an underscore. Storage server names are case sensitive on all platforms including Windows. For example: nbustorageserver_ U41852-J-Z

32 Registering the Storage Server with NetBackup NetBackup OST Guide I If the ETERNUS CS800 S3 is configured with multiple network interfaces (see the User s Guide for your ETERNUS CS800 S3 system), the data IP address of the interface enabled for data should be used to register the storage server Select media server - Select the media server that will access the storage server. The OST Plug-in must be installed on the media server. Enter credentials - Enter the username and password for the storage server. V CAUTION! The username and password must be the same as the OST user credentials created on the ETERNUS CS800 S3 remote management console (see "Configuring OST Authentication" on page 7). I If an error occurs when authenticating in Windows, try using the tpconfig command to validate the OST target (see "Registering the Storage Server on Windows Platforms via CLI" on page 19 or "Registering the Storage Server on Unix/Linux Platforms" on page 21). 6. Click Next. The Storage Server Creation Status window displays (see Figure 12). 28 U41852-J-Z

33 NetBackup OST Guide Configuring Disk Pools and Storage Units in NetBackup Figure 12: Storage Server Creation Status 7. Wait for the wizard to complete the tasks, and then click Next. 8. Click Finish. The storage server is created on the media server. Configuring Disk Pools and Storage Units in NetBackup After the Storage Server has been registered to NetBackup, disk pools and storage units have to be configured in NetBackup. Proceed as follows: 1. Start NetBackup: In Windows, double-click the NetBackup Administration Console icon. U41852-J-Z

34 Configuring Disk Pools and Storage Units in NetBackup NetBackup OST Guide In Solaris and Linux, run the following command: /usr/openv/netbackup/bin/jnbsa & The NetBackup Administration Console displays (see Figure 13). Figure 13: NetBackup Administration Console 30 U41852-J-Z

35 NetBackup OST Guide Configuring Disk Pools and Storage Units in NetBackup 2. In the Details pane (on the right), click Configure Disk Pool. The DIsk Pool Configuration Wizard displays (see Figure 14). Figure 14: Disk Pool Configuration Wizard 3. Click Next. The Disk Pool Type window displays (see Figure 15). U41852-J-Z

36 Configuring Disk Pools and Storage Units in NetBackup NetBackup OST Guide Figure 15: Disk Pool Type 4. Select OpenStorage (FTS) for the disk pool type, and then click Next. The Select Storage Server window displays (see Figure 16). 32 U41852-J-Z

37 NetBackup OST Guide Configuring Disk Pools and Storage Units in NetBackup Figure 16: Select Storage Server 5. Select the storage server that you created on the media server, and then click Next. The Select Volumes window displays (see Figure 17). U41852-J-Z

38 Configuring Disk Pools and Storage Units in NetBackup NetBackup OST Guide Figure 17: Select Volumes 6. Select an available LSU, and then click Next. The Disk Pool Properties window displays (see Figure 18). 34 U41852-J-Z

39 NetBackup OST Guide Configuring Disk Pools and Storage Units in NetBackup Figure 18: Disk Pool Properties 7. Enter a Disk Pool name, and check the other information to make sure it is correct. Then click twice Next. The Disk Pool Configuration Wizard - Summary window displays. Then click Next in order to confirm all entries. The Storage Unit Creation window displays (see Figure 19). U41852-J-Z

40 Configuring Disk Pools and Storage Units in NetBackup NetBackup OST Guide Figure 19: Storage Unit Creation 8. Select the Create a Storage Unit that uses check box, and then click Next. The Storage Unit Creation Details window displays (see Figure 20). 36 U41852-J-Z

41 NetBackup OST Guide Configuring Disk Pools and Storage Units in NetBackup Figure 20: Storage Unit Creation Details 9. Accept the default settings, or modify the following information about the storage unit: Storage unit name - Enter the name of the storage unit. Media Server - Select an option to use any available media server to transport data, or select the specific media server(s) to use. Maximum concurrent jobs - Enter the maximum number of backup jobs that can run concurrently to the storage unit. Maximum fragment size - Enter the maximum size of backup archives that can be written to the storage unit. U41852-J-Z

42 Initiating an OST Backup NetBackup OST Guide 10. Click Next. 11. Click Finish. The Disk Pool is now configured and ready for use. You can view or change current configuration settings in Device Management or Storage Unit Management. Initiating an OST Backup See the NetBackup System Administrator s Guide for information on creating a backup policy to backup data to an OST disk pool. Performing Synthetic Full Backups A synthetic backup is a backup in which content from a series of backups, starting with a full backup and followed by incremental backups, is combined into a new backup-typically a full backup. For a synthetic backup to be successful, all the backups from the series must be intact and internally consistent. Intact means that each backup created still exists and no backup in the series has been expired. Internally consistent means that the individual backup catalogs are all consistent. The catalogs can become inconsistent for a variety of reasons, for example, by running two backups for a client and policy concurrently. (A scenario when this example can occur is if a manual incremental backup is performed while a scheduled incremental backup job is in progress.) During a synthetic backup, the backup application first queries and analyzes the backups for the given policy and client and then attempts to use their catalog data to combine the content into a new logical backup. If a backup is missing, or if file metadata is inconsistent, the synthetic backup will fail with an error 671. Primary causes of error 671 include the following: Expiration of a backup in the full/incremental series. Inconsistent incremental metadata due to concurrent backups in the series. Inconsistent incremental metadata due to utilization of Windows Archive Bit and cumulative incremental backups. Inconsistent incremental metadata due to, prior to NetBackup 7.1, use of dynamic selections and multistreaming. 38 U41852-J-Z

43 NetBackup OST Guide Initiating an OST Backup To configure NetBackup to store optimized synthetic full backups verify the OptimizedImage flag is set for the storage server and the disk pool. To confirm the OptimizedImage flag is set use /usr/openv/netbackup/bin/admincmd/nbdevquery -liststs -U for the storage server and /usr/openv/netbackup/bin/admincmd/nbdevquery -listdp -U for the disk pool. To add the OptimizedImage flag to a existing server use /usr/openv/netbackup/bin/admincmd/nbdevconfig -changests -stype FTS -storage_server <storage-server-name> -setattribute OptimizedImage and to the disk pool use /usr/openv/netbackup/bin/admincmd/nbdevconfig -changedp -stype FTS -dp <disk-poolname> -setattribute OptimizedImage. To configure NetBackup optimized synthetic full backups also see Symantec Technical Solution note TECH U41852-J-Z

44 Initiating an OST Optimized Duplication NetBackup OST Guide Initiating an OST Optimized Duplication The ETERNUS CS800 S3 has the capability to copy data on one system to another system (that is, the capability to perform replication). NetBackup uses this capability to initiate an optimized duplication of backup images between these appliances. The duplication operation of NetBackup triggers the duplication function in the OST disk appliance if both the source and destination volumes for the copy are OST LSUs. OST optimized duplication reduces the workload on the NetBackup media server because the replication is performed by the ETERNUS CS800 S3. Duplication is done in the background, and it is faster because it uses data deduplication capabilities to reduce the copy bandwidth. Duplication is still initiated, managed, and controlled by the NetBackup media server while the actual data movement process is off-loaded to gain the maximum benefits from the appliance s replication capabilities. OST optimized duplication can be used for duplication from or to a ETERNUS CS800 S3 as a disk backup target. I To increase the performance, it is recommended to configure the ETERNUS CS800 S3 to use the replication channel when performing optimized duplication (see "Replication Channel for OST" on page 41) I For versions of NetBackup prior to 6.5.4, no more than two optimized duplication streams per source ETERNUS CS800 S3 to a target ETERNUS CS800 S3 are supported. To initiate an optimized duplication with the Administration Console: 1. In the NetBackup Administration Console, expand the NetBackup Management Catalog. 2. Set up the search criteria for the image you want to duplicate. 3. Click Search Now. 4. Right-click an image you want to duplicate and select Duplicate from the shortcut menu. I You must designate an OST storage unit as the destination for the duplication. Use the Storage Unit field in the Setup Duplication Variables dialog box. I If the optimized duplication fails, the duplication will be attempted using the default duplication method used in versions of NetBackup prior to With NetBackup or 7.x, the administrator can control this failover using a configurable option. See the Symantec Technote at for more information on this option. 40 U41852-J-Z

45 NetBackup OST Guide Initiating an OST Optimized Duplication Also you can initiate an OST Optimized Duplication using the NetBackup Lifecycle Policy. To configure a NetBackup Lifecycle Policy you need two Storage Servers and the associated LSUs on two ETERNUS CS800 S3. For more information, see the sections Duplicating Backup Images and "Creating a storage lifecycle policy" in the NetBackup System Administrator's Guide. Replication Channel for OST Replication Channel for OST allows the ETERNUS CS800 S3 to use the replication channel to perform optimized duplication. This significantly increases performance. In addition, more than two optimized duplication streams per source ETERNUS CS800 S3 are supported. I When using Replication Channel for OST, only a single replication target can be configured on the ETERNUS CS800 S3. V CAUTION! Replication Channel for OST requires the network interfaces used for replication on the source and target ETERNUS CS800 S3 to be on the same subnet. To use Replication Channel for OST when performing optimized duplication: 1. Log on to the ETERNUS CS800 S3 remote management console. 2. On the target ETERNUS CS800 S3, perform the following steps: a) Navigate to the Configuration > Replication > Receive page (see Figure 21). Figure 21: Replication Receive Page U41852-J-Z

46 Initiating an OST Optimized Duplication NetBackup OST Guide b) In the Source Hostname or IP Address box, enter the host name or IP address of the system that will send the replicated data to the ETERNUS CS800 S3. c) Click Add. 3. On the source ETERNUS CS800 S3, perform the following steps: a) Navigate to the Configuration > Replication > Send page (see Figure 22). Figure 22: Replication Send Page b) In the Target Hostname or IP Address box, enter the host name or IP address of the system that will receive the replicated data. c) In the Source IP Address field, enter the IP address that is used to uniquely identify the source ETERNUS CS800 S3 to the target. This may be different than the actual network IP address of the source ETERNUS CS800 S3. If the target system is at ETERNUS CS800 S Software or higher, this field is not required. If the target system is at ETERNUS CS800 S x Software or below, then you must enter the IP address by which the target system recognizes the source system. The default value is d) (Optional) Leave the Use Encryption check box selected to enable encryption when sending replication data to the target system. Or clear the Use Encryption check box to disable encryption when sending replication data to the target system. If encryption is enabled, select an encryption strength (128-bit or 256-bit). Using 256-bit encryption (default) provides a stronger level of security but may have an impact on system performance in some situations. 42 U41852-J-Z

47 NetBackup OST Guide Enabling Verbose Logging V CAUTION! Select 128-bit encryption if you are sending data to a ETERNUS CS800 S3 running a system software version prior to ETERNUS CS800 S Software. I Encryption is enabled by default. However, for best performance, if your data network is already secured, you should clear the Use Encryption check box. e) Click Apply. 4. Perform optimized duplication as normal. Enabling Verbose Logging OST Plug-in Log The OST Plug-in logs various messages to log files under: /var/log/ostlog/client directory on a Linux or Unix media server host and to %WINDIR%\libstspiFTS*.log on Windows. Example # tail -f /var/log/ostlog/client/ost_client.log DEBUG :12: pgnapi.c:57 Plugin Prefix FTS claimed. DEBUG :12: pgnapi.c:58 stspi_claim exited DEBUG :12: pgnapi.c:754 stspi_get_server_prop_byname_v9 entered DEBUG :12: comm.c:939 ostsendrequest: message:0x DEBUG :12: pgnapi.c:798 stspi_get_server_prop_byname_v9 exited DEBUG :12: pgnapi.c:44 stspi_claim_v9 entered DEBUG :12: pgnapi.c:57 Plugin Prefix FTS claimed. DEBUG :12: pgnapi.c:58 stspi_claim exited DEBUG :12: pgnapi.c:207 stspi_open_server_v9 entered DEBUG :12: comm.c:939 ostsendrequest: message:0x U41852-J-Z

48 Enabling Verbose Logging NetBackup OST Guide OST Plug-in Configurable Options The following OST Plug-in configurable options are supported: Linux and Unix The following Linux and Unix configurable options are supported: 1. DEBUG_LEVEL: Defines the level of logging to enable. The value of this option defines the level of log messages to output. It is set to one of the following values: EMERGENCY ALERT CRITICAL ERROR WARNING NOTICE INFO DEBUG By default, DEBUG_LEVEL is set to ERROR. 2. OPDUP_TIMEOUT: The Optimized copy option of NetBackup uses the replication feature of the OST server. The OST server replication feature cannot replicate unless the backup image file is deduplicated. On demand deduplication of the backup image file can take an unknown amount of time. OPDUP_TIMEOUT is the time in seconds to wait for deduplication of backup image file extent of 256 MB or smaller before giving up on the replication attempt. If the file copy extent length is larger than 256 MB, then the wait time will be a proportional multiple of OPDUP_TIMEOUT. For example, if the extent length is X*256 MB, wait time will be X*OPDUP_TIMEOUT, where X need not be an integer. By default, OPDUP_TIMEOUT is set to 180 seconds. I This option is available only on Linux and Unix platforms. On Windows the timeout is fixed at 180 seconds. To change the default value of any of these options, edit the /usr/fts/ftsplugin.conf file and set the desired values. 44 U41852-J-Z

49 NetBackup OST Guide Enabling Verbose Logging Windows The following Windows configurable options are supported: 1. LOG_LEVEL: This is similar to the DEBUG_LEVEL on Linux and Unix. It defines the level of logging to enable. The value of this option defines the level of log messages to output. NONE - Disables logging for the logger. TRACE - Enables tracing to error messages. DEBUG - Enables debug to error messages. INFO - Enables information to error messages. WARN - Enables warning and error messages. ERROR - Enables only error messages. 2. LOG_LIMIT: It defines the maximum file size (in byte) for the logger. Default size of the log file is 10MB. Increase this value if more logging has to be captured. Edit %WINDIR%\libstspiFTS*.ini to change the default values. U41852-J-Z

50 Configuring OST Path to Tape NetBackup OST Guide Configuring OST Path to Tape The OST path to tape (Direct to Tape) option allows you to copy OST LSUs to a physical tape library. I This procedure assumes that you have physically connected the ETERNUS CS800 S3 and the target library using Fibre Channel either directly or through a Fibre Channel SAN. If you are connecting the devices using a SAN, you must perform the appropriate Fibre Channel switch zoning. You must also appropriately map the library device LUNs on the library side to correctly present them to the ETERNUS CS800 S3. Configuring OST path to tape consists of the following major steps. See the following subsections for detailed instructions for completing each step: Verifying Prerequisites Configuring Physical Tape Libraries Configuring NetBackup OST for Path to Tape Verifying Prerequisites The following steps must be completed before setting up NetBackup OST path to tape: The NetBackup version running on the media server must be or later, or 7.x, with all updates applied. The ETERNUS CS800 S3 must be installed and configured. Fibre Channel connectivity must be configured. Aliases for the NDMP host (the ETERNUS CS800 S3) must be created on the EMM server (see "Creating Aliases for the NDMP Host"). Creating Aliases for the NDMP Host For optimal path to tape (direct copy) performance, you should create aliases for the NDMP host (the ETERNUS CS800 S3) on the Enterprise Media Manager (EMM) server. If you create aliases for the ETERNUS CS800 S3, then data is sent directly from the ETERNUS CS800 S3 to tape during path to tape (direct copy) operations. If you do not create these aliases, data will be sent from the ETERNUS CS800 S3 to the media server, then back to the ETERNUS CS800 S3 before it is written to tape, which can cause slower performance. 46 U41852-J-Z

51 NetBackup OST Guide Configuring OST Path to Tape To create aliases for the NDMP host: 1. On the EMM server, retrieve a list of all NDMP hosts (ETERNUS CS800 S3 systems). For Windows, run the following command: C:\Program Files\Veritas\NetBackup\bin\admincmd\nbemmcmd -listhosts -machinetype ndmp For Linux or Solaris, run the following command as root: /usr/openv/netbackup/bin/admincmd/nbemmcmd -listhosts -machinetype ndmp 2. For each host (ETERNUS CS800 S3) returned in Step 1 that will be performing direct copy to tape, retrieve a list of aliases For Windows, run the following command: C:\Program Files\Veritas\NetBackup\bin\admincmd\nbemmcmd -machinealias -getaliases -machinename <ndmphost> -machinetype ndmp For Linux or Solaris, run the following command as root: /usr/openv/netbackup/bin/admincmd/nbemmcmd -machinealias -getaliases -machinename <ndmphost> -machinetype ndmp 3. A host (ETERNUS CS800 S3) should have all available aliases: NetBIOS hostname, DNS hostname, and FQDN (fully qualified domain name). If the host (ETERNUS CS800 S3) does not have one or more of these aliases, you should create them. To create an alias for a host (ETERNUS CS800 S3), use the following commands. For Windows, run the following command: C:\Program Files\Veritas\NetBackup\bin\nbemmcmd.exe -machinealias -machinename <ndmphost> -addalias -alias hostname.domain.gov -machinetype ndmp For Linux or Solaris, run the following command as root: /usr/openv/netbackup/bin/admincmd/nbemmcmd -machinealias -machinename <ndmphost> -addalias -alias hostname.domain.gov -machinetype ndmp I To correct any DNS issues (or simply to be proactive), you can add the entries to the hosts file. U41852-J-Z

52 Configuring OST Path to Tape NetBackup OST Guide Configuring Physical Tape Libraries The Physical Device Discovery page allows you to discover and configure attached physical tape libraries and tape drives. After you discover and configure the libraries and drives, you can use them for path to tape data movement. To discover and configure an attached physical tape library and tape drives: 1. Access the ETERNUS CS800 S3 remote management console. 2. Navigate to the Configuration > PTT > Physical Device Discovery page (see Figure 23). Figure 23: Physical Device Discovery Page 3. Click Scan for Devices to detect attached physical libraries. Attached physical libraries display in the Medium Changers (Physical Libraries) list. 4. Select an attached library by selecting the check box to the left of the library serial number. 5. In the Change intended use for selected changers drop-down list (bottom of page), select Backup Application Specific. 6. Click Apply. 7. To view the library media changer and configured drives, click the Serial Number link for the library. The tape drives display in the Tape Drives list. 48 U41852-J-Z

53 NetBackup OST Guide Configuring OST Path to Tape 8. Click Apply. After the tape library and tape drives are configured, they display in the Medium Changer list located at the bottom of the page. Configuring NetBackup OST for Path to Tape To configure direct path to tape from backups made to the ETERNUS CS800 S3: 1. Access the ETERNUS CS800 S3 remote management console and perform the following steps: a) Navigate to the Configuration > PTT > Backup Application Specific page (see Figure 24). Figure 24: Backup Application Specific Page b) Click Add. c) Specify the Username and Password that are used by the NetBackup NDMP credentials in order to establish an NDMP connection. d) Click Apply. 2. In NetBackup, under NDMP Credentials, you must create a new NDMP host using the ETERNUS CS800 S3 hostname as the name and using the username and password entered in the previous step. The hostname should be resolved by the DNS (see Figure 25). U41852-J-Z

54 Configuring OST Path to Tape NetBackup OST Guide Figure 25: Adding a New NDMP Host 3. In NetBackup, when running the Configure Storage Devices wizard, the user must select the host and set the NDMP option. 4. Continue with the remaining configuration steps in the wizard. A storage unit is created pointing to the physical tape library. 50 U41852-J-Z

55 NetBackup OST Guide Configuring OST Path to Tape Running a Duplication to Tape NetBackup uses NDMP direct copy when you duplicate a backup image. Certain conditions apply to the duplication, explained in this section. To run a duplication, you can use any of the following methods: The Duplicate option in the Catalog node of the NetBackup Administration Console. NetBackup Vault (see the NetBackup Vault Administrator s Guide). The bpduplicate command (see the NetBackup Commands Guide). A NetBackup Storage Life-cycle Policy. Requirements For NetBackup to use NDMP direct copy when you duplicate an image: As the destination for the duplication, you must designate an NDMP storage unit in an ETERNUS CS800 S3. An NDMP tape drive must be available to mount the target image. The NDMP tape drive must be a physical tape drive in a tape library. If these two requirements are met, NDMP direct copy is enabled. NetBackup copies the image directly to the designated storage unit without using media server I/O or network bandwidth. Initiate NDMP Direct to Tape with the Administration Console To initiate a NDMP Direct to Tape with the Administration Console: 1. In the NetBackup Administration Console, expand NetBackup Management > Catalog. 2. Set up the search criteria for the image you want to duplicate. Click Search Now. 3. Right-click the images you want to duplicate and select Duplicate from the shortcut menu. I You must designate an NDMP storage unit (physical tape library) as the destination for the duplication. Use the Storage Unit box in the Setup Duplication Variables dialog box. For more information, see the section Duplicating Backup Images in the NetBackup System Administrator s Guide. U41852-J-Z

56 Configuring ETERNUS CS800 S3 Accent NetBackup OST Guide Configuring ETERNUS CS800 S3 Accent ETERNUS CS800 S3 Accent software accelerates backups and reduces network bandwidth requirements by distributing deduplication between the backup server and the ETERNUS CS800 S3. To use ETERNUS CS800 S3 Accent, all of the following requirements must be met: Firewall port 1062 is open for IP address that is used for data transfer. The media server meets the following requirements: Operating System - Linux CPU - Greater than 2.2 GHz processor with at least 2 cores (4 cores recommended) Memory - 2 GB RAM or greater The OST Plug-in is installed on the media server (see "Installing the OST Plug-in" on page 6). Accent is enabled on the ETERNUS CS800 S3 (see "Enabling or Disabling Accent on the ETERNUS CS800 S3" on page 53). By default, Accent is disabled on the ETERNUS CS800 S3. Accent is enabled on the media server (see "Enabling or Disabling Accent on the ETERNUS CS800 S3" on page 53). By default, Accent is enabled on the media server when you install the OST Plug-in (see "Enabling or Disabling ETERNUS CS800 S3 Accent on the Media Server" on page 54). When all of these requirements are met, Accent will be used for all OST transport between the media server and the ETERNUS CS800 S3. Otherwise, normal OST transport will be used. For information about the maximum number of connections when Accent is enabled, see "Maximum Number of Jobs When Using ETERNUS CS800 S3 Accent" on page 54. I When ETERNUS CS800 S3 Accent is in use, you can monitor Accent performance information in the ETERNUS CS800 S3 remote management console, on the Status > Accent page. For more information, see the User s Guide for your ETERNUS CS800 S3 system. 52 U41852-J-Z

57 NetBackup OST Guide Configuring ETERNUS CS800 S3 Accent Enabling or Disabling Accent on the ETERNUS CS800 S3 By default, ETERNUS CS800 S3 Accent is disabled on the ETERNUS CS800 S3. To use Accent, you must enable it on the ETERNUS CS800 S3. I If Accent is enabled, all media servers that are not running RedHat Linux and that are using the same ETERNUS CS800 S3 must have the latest OST plug-in installed. To enable or disable Accent on the ETERNUS CS800 S3: 1. Access the ETERNUS CS800 S3 remote management console. 2. Navigate to the Configuration > OST > Accent page (see Figure 26). Figure 26: Accent Page 3. To enable ETERNUS CS800 S3 Accent, select the Enable Inline Dedupe with Accent check box. Or to disable ETERNUS CS800 S3 Accent, clear the Enable Inline Dedupe with Accent check box. 4. (Optional) Select the Use Encryption check box selected to enable encryption when sending OST data from the media server to the ETERNUS CS800 S3. Or clear the Use Encryption check box to disable encryption when sending OST data from the media server to the ETERNUS CS800 S3. If encryption is enabled, select an encryption strength (128-bit or 256-bit). Using 256- bit encryption (default) provides a stronger level of security but may have an impact on system performance in some situations. 5. Click Apply. U41852-J-Z