LXP200 and Elastix Server

Transcription

1 LXP200 and Elastix Server Setup Guide

2 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single IP phone Elastix LXP200 configuration. The phone is setup as a SIP telephony device. Figure 1-1. Setup Diagram 2.0 Host PC Environment Table 2-1. Host Server Environment Details Description Hardware Type Elastix Appliance ELX-Series Hardware Version ELX-3000 Software Type Elastix Software Version Test Setup Equipment Table 3-1. Test Setup Equipment Equipment Model Version Video Call IP (SIP) Phone N/A N/A Palosanto Solutions Elastix LXP Switch N/A N/A 2

3 4.0 Setup Procedure To set up the Elastix Server for the Elastix LXP Go to the web address of the Elastix Server Login page. The web address is determined by the customer, for this guide we have used the IP address On the Login page, type the username and password for an administrative user into the Username and Password fields, see Figure 4-1. The username and password are determined by the customer. Figure 4-1. Login 3. Press Enter or click on the Submit button to go to Elastix s Dashboard 4. Once inside, click on the PBX tab on the menu at the top of the screen Figure 4-2. Dashboard 3

4 5. Click on the Submit button to add an extension, see Figure 4-3. This will take you to the Add SIP Extension page. Figure 4-3. Add an Extension 6. On the Add SIP Extension page (Figure 4-4), fill in the following information: User Extension (301 in this example) Display Name ( LXP200Phone in this example) secret ( h7dka3rf9si0t in this example) Figure 4-4. Add SIP Extension 7. Click on Submit button at the end of the page, and you will see a similar page on Figure 4-5 displaying the Apply Configuration Changes Here pink ribbon on top of the screen. Click on there to apply changes. 4

5 Figure With this you have just finished creating a SIP extension that will be used by the Elastix LXP200 to register with the Elastix Server. Repeat Steps 5 through 7 to similarly create another extension (different values on Step 6) to be used by the IP (SIP) Phone to register as well (extension 302 in this example). Once you finished you will see something similar to Figure 4-6. Figure You will need to enter the information from the extension created on the Elastix Server into the LXP200 Phone. Connect the LXP200 phone to the same network than Elastix Server. The default values configured on the phone are: Factory default settings IP Addressing Web Access Password DHCP admin When the phone obtains an IP Address from your DHCP server, it is shown on the main screen of the phone. If you don t have a DHCP server and you want to set static IP addressing you must do the following: From the phone, press Menu => Network => IP Setting => Static IP. Menu button is the one which is located in the middle of the arrow buttons. 5

6 Now set the values for connecting to the network. When you finish, select Back option and you will be asked for rebooting. Select YES. To register the Elastix Phone there are two methods: Manual Configuration and AutoProvisioning using Elastix s Endpoint Configurator. 6

7 MANUAL CONFIGURATION 1. Log in to the Elastix LXP200 WebUI by pointing your browser to the Elastix Phone s IP address. 2. When prompted, enter the Web Access Password to accesss to the WebUI (Figure 4-7). Figure 4-7 Elastix Phone WebUI 3. Use the information from the Add SIP Extension page (Figure 4-4) to enter the following necessary information on Accounts => Account 1 section of the LXP200 Phone WebUI (Figure 4-8): Account Active: Yes Account Name: ElastixPhone SIP Server: Elastix Server s IP Address ( in this example) SIP User ID: 301 Authenticate ID: 301 Authenticate Password: ( h7dka3rf9si0t in this example) 7

8 Figure 4-8. Account 4. Once you have entered the required information, click on Update button located at the end of the page. 5. To check the correct registration of the phone, go to Status section. You should see your phone registered (Figure 4-9). If the phone is not registered, make sure you ve entered the correct information. Figure 4-9. Status 6. Configure the other IP (SIP) Phone with the correct parameters. 7. To test the Elastix LXP200, pick up the previously configured IP (SIP) Phone and call the LXP200 s extension number (301 in this example). When the call is established, speak into the phone and verify that the other IP (SIP) Phone can hear your voice. Check this by calling from both ends. This step completes the manual procedure. 8

9 AUTOPROVISIONING USING ELASTIX S ENDPOINT CONFIGURATOR Note: The support for Endpoint Configurator is available in Elastix 2.4 by installing the new Endopoint configurator module. This new module is already included in Elastix For Elastix 2.4, log in to the console and install the module by entering the command: yum -y install elastix-endpointconfig2 2. After installation, in the Elastix Web Interface go to PBX => Batch Configurations => New Endpoint Configurator. See figure 4-10 Figure New Endpoint Configurator 3. Type the network address where the phone is located and click on the magnifying glass. This will generate a list with all the phones available in that network. See figure Figure List of endpoints 4. In the row where the phone you want to autoprovision is located (find it according to either its MAC or IP Address): Mark the checkbox From the drop-down list, select the correct Phone Model if it is not detected automatically Click on the link [Configure x.x.x.x] to set the parameters to configure the phone. 9

10 5. After clicking in the configuration link, you will see a window with many tabs according to what you want to configure. In this case we will configure a SIP account. Go to the tab Accounts and drag the accounts you want to assign from left to right. Then click on Apply button. See figure Figure Accounts configuration 6. After configuring you will see that the status field of the phone has changed. See figure 4-13 Figure List of endpoints 7. Now with the phones selected, click on the button Apply Configuration located next to the magnifying glass button. A message will be shown saying the operation was successful. See figure

11 Figure Configuration successful 8. Your phone will reboot, and when it boots up it should be registered with Elastix with the accounts you set. This step completes the procedure. 11