Allo GSM 4 modules.

Transcription

1 Allo GSM 4 modules and Elastix Server Setup Guide

2 1. Setup Diagram Figure 1-1 is a setup diagram for a single Allo GSM Interface Card configuration. Figure 1-1. Setup Diagram 2. Host PC Environment Table 2-1. Host Server Environment Details Hardware Type Hardware Version Software Type Software Version Description Elastix Appliance ELX-Series ELX-3000 Elastix Test Setup Equipment Table 3-1. Test Setup Equipment Equipment IP (SIP) Phone Allo Switch Model N/A GSM 4 modules N/A Version N/A chan_allogsm N/A 2

3 4. Setup Procedure To install the Allo GSM driver, 1. Log in as root using a ssh client or directly from Elastix server. (Figure 4-1) Figure 4-1. Logging in the Elastix Server 2. Check the subsystem ID of the card with the command lspci vn. If the ID is the same as shown in Figure 4-2, you can proceed with the installation Output of lspci command 3. Install the Allo GSM driver: yum install chan_allogsm kmod-allogsm 4. Restart asterisk: service asterisk restart 5. Now go to Asterisk Cli and type allogsm show status to verify the SIM card is correctly registered. (See figure 4-3) Figure 4-3. Port status 3

4 PaloSanto Solutions To set up the Elastix Server for the Allo GSM Interface Card, 1. Go to the web address of the Elastix Server Login page. The web address is determined by the customer, for this guide we have used the IP address On the Login page, type the username and password for an administrative user into the Username and Password fields, see Figure 4-4. The username and password are determined by the customer. Figure 4-4. Login 3. Press Enter or click on the Submit button to go to Elastix s Dashboard. See figure 4-5 Figure 4-5. Dashboard 4. Once inside, click on the PBX tab on the menu at the top of the screen and go to PBX Configuration (Figure 4-6) 4

5 Figure 4-6. PBX 5. Click on Extensions and select Generic SIP Device to create an extension for the IPPhone. In the Add SIP Extension page fill in the following information (Figure 4-7): Add Extension User Extension: (302 in this example) Display name: ( IPPhone in this example) Device Options Secret: ( h7dka3rf9si0t in this example) Figure 4-7. Add SIP Extension 6. Click on Submit button located at the end of the page and apply changes. Now, click on Trunks on the left side and select Add Custom Trunk (Figure 4-8). 5

6 Figure 4-8. Trunks 7. On the Add Custom Trunk page, set the following parameters (Figure 4-9). General Settings Trunk Name: ( Allo_Trunk in this example) Outgoing Settings Custom Dial String: GSM/1/$OUTNUM$ The number 1 is the port we ll use for outbound calls. In this case we have the SIM card located in the first port. Figure 4-9. Custom Trunk 8. Click on Submit Changes button located at the end of the page. Go to PBX => PBX Configuration => Outbound Routes. Click on Add Route (Figure 4-10). Set the following parameters: Route Settings Route Name: ( 9_Outside in this example) Dial patterns 6

7 Prefix: ( 9 in this example) Match pattern: (. in this example) Trunk Sequence for Matched Routes 0: The trunk that we just created ( Allo_Trunk in this example) Figure Outbound Route 9. Now you can make outbound calls through the SIMCARD calling a telephone number with 9 as prefix. 10.We ll create an incoming route for the calls from any external number to our SIMCARD. We re going to use an IVR for incoming calls. Go to PBX => PBX Configuration => IVR. Click on Add IVR (Figure 4.11). Set the following: Name: Name of IVR (WelcomeIVR in this example) Announcement: Record which will be played for incoming calls. Options: o * - Phone book. o Extension o t - Repeat the options of IVR (Add this option by modifying the IVR after creation) 7

8 Figure IVR 11.Click on Save and Apply changes by clicking on the pink ribbon that appears at the top of the page. Now go to PBX => PBX Configuration => Inbound Routes. Click on Add Incoming Route. (Figure 4.12). Set the following: Description: Name of inbound route ( Incoming_Calls in this example) Set destination: Where the call will be routed. ( WelcomeIVR IVR in this example) Figure Incoming Route 12.Click on Submit button and apply changes. Now when we receive calls to the SIMCARD the WelcomeIVR IVR will be played to the caller giving him choices to interact with Elastix Server. 13.Configure the IP (SIP) Phone with the correct parameters. 14.To test the configurations, pick up the previously configured IP (SIP) Phone and dial a mobile phone with 9 as prefix (in this case ). When the call is established, speak into the phone and verify that the mobile phone can hear your voice. Next, from your mobile phone call to the SIMCARD number (in this case ) and when the call is established you should be interacting with the IVR. 8

9 SMS Functions Sending SMS On Asterisk CLI, enter the following command to send a SMS to a mobile phone: allogsm send sms "Your message here" Figure Sending SMS Here we tell Asterisk to send a SMS from port 1 to The message should be received by the destination. Receiving SMS Send a SMS from any mobile phone to the number of our SIM card located on the Allo Card. You should see an informative message on Asterisk CLI telling you that a SMS was received. To see the message, enter the following command: allogsm show sms 1 The number 1 is the port where the SIM card is located in the Allo GSM card. Figure Receiving SMS 9