Sirius Lighting Design ENG User Manual

Transcription

1 Sirius Lighting Design ENG User Manual Updated 17 July, 2017 Copyrightc 2017 LG Innotek Co., Ltd.

2 Table of Contents 1 Introduction System requirements Interface devices UART Interface Board NFC Transceiver Supported Models GUI for Sirius Lighting Design Main Window Port Setup UART NFC Menu Bar Menu File Menu Tools Menu View Menu Help Tool Bar Network and Device Panel Scan Network Commission Group Control Device(s) List Feature and Command Window Copyrightc 2017 LG Innotek Co., Ltd.

3 5.6.1 Feature Tab Log Window Features Product ID/Barcode Dimming Interface Selection Maximum Output Current (MOC) LED Module Working Hours V Dimming Schedule Dimmer Lumen Output Compensation (LOC) Release Note of Sirius Lighting Design Page 3 / 35

4 1 Introduction Global greenhouse gas reduction policy and restrictions on electrical and electronics hazardous products has led us to the urge of replacing traditional lighting control system with environmental friendly, high energy efficient and effectively controlled lighting system. The traditional simple ON/OFF electrical and electronic switches have been used to control two states of light i.e. ON and OFF. Recently, a need has been observed to control lighting system in a more sophisticated manner introducing illumination control, distributed and/or centralized control along with the traditional ON/OFF control. Programmable LED Lighting Power provides a very flexible and optimal lighting control mechanism both for distributed and centralized light control. You can control the many features of LGIT LED Driver you want through the Sirius UI program. Page 4 / 35

5 2 System requirements In order to make full use of the feature of the Sirius, the followings are required. - Windows desktop computer or notebook - OS(32bit): Windows XP or Windows 7(recommended) - Communication: USB 2.0 ports - DLL(Property): 1) Silicon Labs HID Device Interface Library V1.6, HID to UART Dynamic Link Library V2.0 2) FEIG ELECTRONIC Function Library FEUSB and FEISC - Program running environment: Should be in release directory. Page 5 / 35

6 3 Interface devices To communicate with the LED Driver, user must connect the interfaces to the PC. Sirius Lighting Design program can support the UART and NFC communication. 3.1 UART Interface Board There are the interface board between PC and the LED Driver. It has a Mini-USB connector, UART connector and VCC (3.3V) output connector. VCC (3.3V) output connector is used for firmware upgrade without AC power source. You can connect the driver with interface board using dongle connector easily. For more detail guide, please refer to the Sirius Lighting Design Connection Guide document. < Interface Board (USB to UART) > Page 6 / 35

7 < Block Diagram > 3.2 NFC Transceiver The Sirius Lighting Design with NFC Transceiver can control LED Driver that can communicate with NFC. The Sirius Lighting Design can support 2 types of NFC Transceiver (CPR30-USB and ISC.PRH101-USB) <CPR30-USB> <ISC.PRH101-USB> Page 7 / 35

8 < Block Diagram > Page 8 / 35

9 4 Supported Models Sirius Lighting Design program can manage several models. You can check supported models and functions of model with the following table. Function Configurable of Dimming Interface Supported Dimming Interface Function Feature Others Communication Type Schedule Item Readable Writable DALI 1-10V Location GEN1 PIFN-W030B PIFN-W055B UART GEN2 PIFN-W030C PIFN-W050C NFC Timebased No Dimming AC Dimming No Dimming MOC MTP LOC MWH Power Status Barcode Read FW Update EEPROM Initialize Model <Function Table> Page 9 / 35

10 5 GUI for Sirius Lighting Design 5.1 Main Window Double click the LED Controller executable. A GUI window will pop-up containing the following Panels: - Menu bar: Contains the different menus supported by the GUI - Tool bar: Provides quick access to frequently used functionality - Network and Devices Panel: Panel showing the devices and the groups in the network. - Feature and Command Window: Window showing the feature set associated with the devices and allows the user to read, modify and update the feature parameters and their settings. - Logging Window: Shows the status logs NOTE: According to connected interface devices, A GUI window would be changed suitably. Page 10 / 35

11 5.2 Port Setup The user can select the interfaces to communicate with the product through the Port Setup function. The UI changes depending on the connected interface. First, detect the connected interfaces when running the program. If interface which connect with PC is only one, Sirius Lighting Design program connect one automatically. If more than one, program show the Port Setup Dialog to select. Connection setting can change after start time by ToolsPort UART Deactivate Command Tab NFC Deactivate Command tab, and FW Update function. For detecting LED Driver, user clicks the Scan network button. When clicking Scan network, Logging screen will be output for about 10 seconds and the product antenna should be contacted on the transceiver. 1) CPR30-USB : Put on the LED Driver s antenna to NFC Transceiver. 2) ISC.PRH101-USB : Put on the LED Driver s antenna and click the NFC Transceiver s button. Page 11 / 35

12 5.3 Menu Bar Menu bar contains 4-main menu items. Place the cursor on the menu item to view the drop down action items for each of them. In this chapter, user can find each of feature s role in the program Menu File The File menu contains the following actions. - Open: Click on this action item to invoke an Open File dialog. Select a LGT (.lgt) file and click on Open. The values of each feature are updated. NOTE: When the configuration file is opened, UI program check the compatibility between the configuration file and Sirius. If the configuration file is incompatible with current Sirius version, the error message is popped up. Then you should open another configuration file or make the new configuration file. Page 12 / 35

13 - Save: Click on this action item to save the current information into the LGT (.lgt) file. Feature configurations can be saved to a file for later use. Click the File-Save button in the top menu. You can save the configuration file using current value of each feature. - Save As: Click on this action item to invoke a Save File dialog. After setting the folder directory and file name, click on Save to save the current information into an LGT (.lgt) file. Feature configurations can be saved to a file for later use. Click the File-Save button in the top menu. You can save the configuration file using current value of each feature. NOTE1: Check the selected model before saving configuration file. Model information will be included in data file. This information will be used at Sirius factory version in order to verify connection of correct device. If the version or model is not matched between data file and connected device, the error will be occurred. NOTE2: It will be only supported to English language about Open, Save and Save As. - Exit: Click on Exit button to close the program. Any unsaved data will be prompted to be written into an LGT(.lgt) file. Page 13 / 35

14 5.3.2 Menu Tools - Add Virtual Device: Click on this action item, a device Model Selection dialog will popup on the screen. Select the current model by selecting a row and pressing the OK button. - Read: Click on this action to read the Device Configuration data from the connected device. The following Feature Configuration dialog will pop-up listing all the available features for the current device/model. Select or un-select the features to read and click on OK. There would be a communication with the device and selected features of the device will be read and displayed. - Write: Click on this action to write Device Configuration data to the connected device. The Feature Configuration dialog will popup listing all the available features for the current device/model. Select or un-select the features to write and click on OK. The features will be written to the device. In order to write, Read must be preceded. Copyrightc 2017 LG Innotek Co., Ltd.

15 NOTE: Before reading/writing with device, model connection should be done previously to make clear which device will communicate with PC. - Port Connection: Click on this action, the Port Setup dialog will pop-up. USB port configuration is carried out automatically. Before communication with a device, you should check status of port connection. In the upper right corner of the UI main window, current connection status with interface board is displayed. Port is automatically opened when the interface board is connected to the PC using USB cable. XXX Connected represents that the connection is OK. If Disconnected is displayed, check the connection between PC and interface board. Click the Port setup button, dialog is popped up. In this dialog, you can see the detail information of the connection. Page 15 / 35

16 - Firmware Upgrade: Click on this action to upgrade the Firmware. The Firmware Update dialog will pop-up. User can run this Firmware upgrade feature by using 2-way. This program supports auto sequence and Manual mode. Auto sequence is running the program download sequentially, and Manual mode is running step-by-step as user selection. Use this feature to update the firmware. Firmware update sequence is as follow. File Open: Open the binary file (.bin) offered by LG Innotek. App->Boot: Jump to boot loader region to upgrade firmware. Erase: Erase the flash memory of application region. Write: Write updated file data on flash memory. It will take about 20minutes. Boot->App: Jump to application region to run application program. Security Code: Write the security code to protect the application data. Initialize EEPROM: Initialize the data of EEPROM after download Page 16 / 35

17 - Group Control: This feature is arranged for other model. UART interface board or NFC transceiver is connected, this feature would be disappeared. - Init. EEPROM: Using this feature EEPROM can be initialized. This feature is used to initialize the configuration of LED Driver and make the device as factory reset. After send the Initial EEPROM function, AC power reset is required to initialize. Page 17 / 35

18 5.3.3 Menu View This menu contains the following actions: View menu. - Panels : this action consists of other actions as listed below. Devices: Check/Uncheck of this action will retain/remove the Network and Devices panel from Main Window. Logging: Check/Uncheck of this action will retain/remove the Logging Window from the Main Window. Device Features: Check/Uncheck of this action will retain/remove the Device Features Tab from the Main Window. Command: This feature is arranged for other model. UART interface board or NFC transceiver is connected, this feature would be disappeared. Quick Menu Bar: Check/Uncheck of this action will retain/remove the menu bar from Main window. Page 18 / 35

19 5.3.4 Menu Help This menu contains the following actions as shown below. - About: Click to get the version information. This dialog contains detail information of Sirius program and connected device (converter). This information will be used for checking compatibility of the UI program. - User Manual: Click to open the user manual which is supported by html. - Supported Devices: Click on this action item to pop up a Model Selection dialog of the list of supported devices. Copyrightc 2017 LG Innotek Co., Ltd.

20 5.4 Tool Bar Tool bar contains icons for quick actions. The expanded view of the tool bar as below: - Open : The functionality is same as FileOpen action item - Save : The functionality of this icon is same as FileSave action item - Read : The functionality of this icon is same as ToolsRead action item - Write : The functionality of this icon is same as ToolsWrite action item - Port : The functionality of this icon is same as ToolsPort action item Page 20 / 35

21 5.5 Network and Device Panel This panel contains the list of connected devices. The connected devices and groups will be shown in the form of expandable tree view. The panel consists of 3 buttons. Use Scan Network and Commission button to find the connected model. When you run these items, program starts to find connected model. There is no need to select model. Program will detect the model name or type and update its information in the devices list panel Scan Network - This button Perform appropriate actions according to the connected interface. - When UART Interface board is connected, the program communicated only 1- indoor model drivers at once. - When NFC transceiver is connected, the program detects the NFC transponder with logging window. And unsupported features would be disappeared on screen, likes group control, command tab, etc. You can check on by NOTE in this manual Commission - When UART Interface board or NFC transceiver is connected, this button would be invisible Group Control When UART Interface board or NFC transceiver is connected, this button would be invisible Device(s) List Click on this drop down for the following options: Configuration File Configuration file can be loaded in any of the following ways: a) From Menu bar: FileOpen b) Keyboard shortcut: Ctrl + O c) From Devices panel: All DevicesConfiguration File(right click)load File d) From Tool bar: Click on the Open icon A window will pop up to select the.lgt file. Virtual Devices Virtual devices can be loaded in following ways: a) From Devices panel: All Devices Virtual Devices (right click) Add Virtual Device b) Tools Add Virtual Device c) Keyboard shortcut : Ctrl + M A window will pop up to select virtual devices. Copyrightc 2017 LG Innotek Co., Ltd.

22 Scanned Devices Scanned devices can be loaded in any of the following ways: a) From Device panel : All Devices Scanned Devices (right click) Scan For Devices b) Click on Scan Network or Commission button LED Driver(s) which is connected to the interface module gets loaded. If LED Driver is not connected, error message will be shown in the screen to request the connection status again. NOTE1: Based on the connected model information, MOC range will be applied (MOC range depends on the output power of LED Driver). Model information will be included in data file. It will be used at Sirius factory version in order to verify the connection of correct device. If the version or model information is not matched between data file and connected device, the error will be occurred. NOTE2: When UART Interface or NFC Transceiver is connected, Commission, Group Control button and User Defined Group list would be disappeared. Page 22 / 35

23 5.6 Feature and Command Window Feature Tab - The user can view and configure the features of a selected device in this tab. Upon selection of a device, all the supported features of the device are visible in a sub-panel. The features are displayed to the left of the window. The features that are visible depend on the device model. The user can click on any of the features and configure them. A page summarizing the supported features and their configurations is shown in the Summary page. The summary page gives an overview of Power Status, the enabled features and their configurations. Page 23 / 35

24 5.7 Log Window All the log messages are shown in this window. Timelines, short address, commands and their result status will be displayed in this window. This updated information is automatically saved into the excel sheet in program directory. Page 24 / 35

25 6 Features 6.1 Product ID/Barcode Description Use the Product ID feature to know what type of product is connected. You can also read the barcode information of the product Practical Use Click the Read button after connection with product, the version and Product ID will be displayed. The version is divided two sections, the major and the minor version. The major version will be increased when the huge change is occurred. For example, add the new features to the driver. In this case, configuration file (*.lgt) should be made newly. The minor version is increased when the firmware is little bit changed. In this case, do not need to change the configuration file. And you can read the barcode information of the product by click on the Barcode button. The barcode information is consists of 17-digit character and number Value Setting Product ID/Barcode is product s specific information. User cannot set this information. No ITEM Default Value Variable Range 1 Product Barcode - - Copyrightc 2017 LG Innotek Co., Ltd.

26 6.2 Dimming Interface Selection Description Use the Dimming Interface Selection feature to determine the dimming method for product. Selectable items are: - DALI V - Schedule dimmer - AC Dimming - No dimming NOTE: In GEN2 driver, dimming interface is selected automatically Practical Use You can select Dimming Interface to click radio button and showing screen will move to relative feature tab. When 1-10V has been selected, showing screen will be changed to 1-10V min. Level feature tab to configure the minimum dimming level. When Schedule dimmer is selected, showing screen will be changed to Schedule Dimmer feature tab. You can configure the time table and dimming level including override, operating mode (Time/Location/No dimming) and midnight shift Value Setting No Interface Model Default Value Variable Range 1 Dimming Interface PIFN-W030B PIFN-W055B 1-10V 1-10V, Schedule dimmer, PIFN-W030C PIFN-W050C Schedule Schedule Copyrightc 2017 LG Innotek Co., Ltd.

27 6.3 Maximum Output Current (MOC) Description Use this Maximum Output Current feature to adjust the maximum output current. You can produce LED Module of various wattages by adjusting MOC value Practical Use You can control the output current using slider or spin box. The range of MOC is automatically changed according to the product information. MOC Slider: Set the slider value between the low and high output current. Spin box automatically gets updated to the value changed by the slider. Spin-Box: Set the value of spin box between low and high output current. The Slider gets automatically updated to value in the spin box Value Setting No Interface Model Default Value Variable Range 1 Maximum Output Current PIFN-W030B 1050mA 150mA ~ 1050mA PIFN-W055B 1500 ma 400mA ~ 1500mA PIFN-W030C 1050 ma 150mA ~ 1050mA PIFN-W050C 1400 ma 400mA ~ 1400mA Page 27 / 35

28 6.4 LED Module Working Hours Description Use this LED Module Working Hours feature to set up the operating hours of LED module. This information let user know that replacement time of LED module and used for LOC setting Practical Use You can change the LED Module Working Hours using slider or spin box. MWH Slider: A slider ranging module working hours between 0-127,500(hr). On dragging slider its changed value can be visualize in spin-box. Spin-Box: A spin-box to display the maximum output current numerically in range 0-127,500(hr). Any change made in spin-box is reflected in Slider as well Value Setting No Working Hours Default Value Variable Range 1 LED Module Working Hours 0H 0H ~ H Page 28 / 35

29 V Dimming Description 1-10V is available when Schedule type is No dimming. 1-10V is used to control output current of LED Driver, depending on DIM+/- level of LED Driver. You can set up 1-10V Min. Level by using Sirius Program Practical Use If the LED driver is in 1-10V dimming mode, Dimming level (Output Current) would change from 1-10V Min. Level to Max Level 100%. According to the voltage level of DIM+/-, Dimming level is calculated linearly based on the 1-10V Min. Level. Min level operation and dimming level is set by increase and decrease of voltage level measured in DIM+/-. Voltage Slider: Set the value between the range of min level-100(%) by moving slider. The min level is defined by model type. Spin Box: Set the value between the range of min level-100(%) by changing the spin box or manually typing the number in the spin box. The min level is defined by model type. NOTE : For more detail about Dim Low/Dim High, please refer to the data sheet of LED Driver. Page 29 / 35

30 6.5.3 Value Setting No Interface Model Default Value Variable Range 1 Dimming Interface PIFN-W030B PIFN-W055B 5 % 5%~ 100% PIFN-W030C PIFN-W050C 1 % 1%~ 100% Page 30 / 35

31 6.6 Schedule Dimmer Description Schedule dimmer is used to automatic dimming control of LED Driver. As time has passed, the dimming of LED Driver is changed according to the schedule table Practical Use Select the schedule dimmer in the dimming interface for enable this function. - Time based: If the Time based is selected, the schedule dimmer operates as a time based mode. When the switch of the main power is turned on, the dimming of the LED driver is changed according to the table from No. 0 to No. 4. Users can set the maximum five steps of the schedule within 24 hours. - No dimming : If the No dimming is selected, the schedule dimmer operates as a time based mode.. It is the same as running on a 100% schedule of time base. In this mode, 1-10V Dimming mode will be available. - Override: The override function maintain output to 100% during predefined hold time when certain event is occurred on the mode of schedule dimmer. Select the override check box to use this feature. Page 31 / 35

32 No Value Setting Schedule Dimmer Model Default Value Variable Range 1 Override All Not Disabled Enable or Disabled 2 Hold time All 0min 60min 3 Midnight Shift(Minute) 4 Schedule type 5 Schedule All 0min Disable Only PIFN-W030B PIFN-W055B PIFN-W030C PIFN-W050C PIFN-W030B PIFN-W055B PIFN-W030C PIFN-W050C Time based No dimming No Time(hh:mm) Dim(%) 0 00: : : : :30 80 No Time(hh:mm) Dim( %) 0 00: Time based Time based No dimming Number of Schedule : 5 Hour : 00H ~ 23H Min : 0M ~ 59M Dim : 0%, 5% ~ 100% Number of Schedule : 5 Hour : 00H ~ 23H Min : 0M ~ 59M Dim : 0% ~ 100% Note: If user configured the new schedule data using Schedule dimmer feature tab and write data to the device, then AC Power should be restarted in order to apply. Page 32 / 35

33 6.7 Lumen Output Compensation (LOC) Description The efficiency of LED module is decreased over time naturally. For that reason the brightness of LED module decrease for same output power. To maintain the constant brightness, it increase the output current as time goes on Practical Use In order to use this feature, you should select the enable check box. You can insert the time schedule and diming level in the table up to 16 steps. First column is operating hours and second column is light level. LED module working hours and power level can be put what you want. Minimum step of operating hours is 500 hours. Power level is adjustable up to 130%. If the Enable check box is selected, the device will follow the schedule in the table in order to compensate brightness of the lamp. According to the LED module working hours, rate of power level is multiplied to final dimming level. LOC table values can be modified or updated in any of the following ways: Editing cell value: Editing the cell values is possible in the range of specified by LOC feature ADD button: Entering the Hour and Dim (%) and clicking on ADD. The new value will be added only if same working hour to be added is not already existed in the table. Delete button: Clicking on DELETE, the selected row will be deleted. Moving graphs: Moving graphs is possible to update the table concurrently. This is valid when moving the vertical and horizontal level of graph. New schedule: Clicking the New Schedule button creates user configurable LOC table data. The user can either select the empty/default schedule or custom schedule. Sirius program supports user configuration as custom schedule, so user can configure the number of steps, configurable working hours, initial and final dimming values using this window. Copyrightc 2017 LG Innotek Co., Ltd.

34 6.7.3 Value Setting No LOC Default Value Variable Range 1 Enable Not enabled Enable or Not enable 2 Table No Time(hh:mm) Dim(%) Number of Schedule : 16 Hour : 0H ~ H Dim : 10% ~ 130% Page 34 / 35

35 7 Release Note of Sirius Lighting Design Version Date Comment V1.36I [Flat] 04-May-2017 Initial Release V1.40 [Flat] 19-June-2017 Fix some bugs about graph UI Page 35 / 35