All Sport 100 Control Console

Transcription

1 All Sport 100 Control Console Operations Manual ED Rev 3 10 October 2007

2 ED13432 Product 1196 Rev 3 10 October 2007 DAKTRONICS, INC. Copyright All rights reserved. While every precaution has been taken in the preparation of this manual, the publisher assumes no responsibility for errors or omissions. No part of this book covered by the copyrights hereon may be reproduced or copied in any form or by any means graphic, electronic, or mechanical, including photocopying, taping, or information storage and retrieval systems without written permission of the publisher. All-Sport is a trademark of Daktronics, Inc

3 Table of Contents Section 1: Introduction How To Use This Manual Daktronics Nomenclature...3 Section 2: Controller Overview All Sport 100 Overview Display Connection Replacement Parts List Daktronics Exchange and Repair and Return Programs...6 Exchange Program...6 Before Contacting Daktronics...7 Repair & Return Program...8 Shipping Address...8 Section 3: Basic Operation Console Operation All Sport 100 Inserts and Codes Sport Insert Operation Concepts Startup Common Sport Keys...11 Start...11 Stop...11 Enter/Edit...11 Clear/Alt...11 Set Time...11 Count Up/Down...12 Auto Horn...12 Manual Horn...13 Dimming...13 Section 4: Clock/Score Operation Clock Keys...15 Set Time...15 Period Score Keys...17 Home/Guest Score Keys...17 Bonus Keys...17 Possession Key...18 Table of Contents i

4 Section 5: Segment Timer Operation Segment Timer Information Segment Timer Keys...20 Main Screen...20 First/Last Segment...20 Segment Number/Time...20 Set Program...21 Interval Time...21 Copy Range...22 Auto Stop...22 Warning Time...22 Reset Current Segment...23 Edit Current Segment...23 Reset to First Segment...23 TI-2025/2026 Segment Timer...23 Send Program Information to Display...23 TI-2025/2026 Play Clock (Segment Timer Program 6)...24 TI-2025/2026 Two-Minute Drill (Segment Timer Program 7)...24 RC-50 Segment Timer...25 Controls (Programs 1-5)...25 RC-50 Play Clock Controls (Program 6)...25 RC-50 Two-Minute Drill Controls (Program 7)...25 Section 6: Baseball Operation Baseball Keys...27 Out +1, Inning Ball, Strike, Clear Ball/Strike...28 Hit, Error...28 Home/Guest Score +1, Appendix A: Reference Drawings ii Introduction

5 Section 1: Introduction 1.1 How To Use This Manual Important Safeguards: 1. Read and understand these instructions before installing the display. 2. Do not drop the control console or allow it to get wet. 3. Properly ground the scoreboard with a grounding electrode at the scoreboard location. 4. Disconnect power when the scoreboard is not in use. 5. Disconnect power when servicing the scoreboard. 6. Do not modify the scoreboard structure or attach any panels or coverings to the scoreboard without the express written consent of Daktronics, Inc. Figure 1 illustrates the Daktronics drawing numbering system. Daktronics identifies individual engineering drawings by their drawing number (7087-P08A in the example), which is located in the lower right corner of the drawing. This Figure 1: Daktronics Drawing Label manual refers to drawings by their last set of numbers and the letter preceding them. The example would be Drawing A Reference drawings are grouped and inserted in alphanumeric order in the Appendix. Listed below are a number of drawing types commonly used by Daktronics, along with the information that each is likely to provide. System riser diagrams: overall system layout from control room to display, power and phase requirements Shop drawings: fan locations, transformer locations, mounting information, power and signal entrance points and access method (Front or rear) Schematics: power wiring, signal wiring, panelboard or power termination panel assignments, signal termination panel assignments and transformer assignments Final assembly: component locations, part numbers, display dimensions and assembly/disassembly instructions Introduction 1

6 All references to drawing numbers, appendices, figures, or other manuals are presented in bold typeface, as in this example: Refer to Drawing A for the location of the driver enclosure. Additionally, any drawings referenced within a particular subsection are listed at the beginning of that subsection in the following manner: Reference Drawing: Segmentation, 7 Seg Bar Digit... Drawing A Daktronics identifies manuals by their engineering document (ED) number, which is located on the cover page of the manual. For example, this manual would be referred to as ED The serial and model numbers of a Daktronics scoreboard can be found on the ID label on the display. The label will be similar to the one shown in Figure 2. When calling Daktronics Customer Call Center, please have this information available to ensure quick service. For future reference, note the scoreboard model number serial number, and installation date on the second page of this manual. Figure 2: Scoreboard ID Label Daktronics displays are built for long life and require little maintenance. However, from time to time, certain display components will have to be replaced. The Replacement Parts List in Section 2.3 provides the names and part numbers of components that may require replacement during the life of this display. Following the Replacement Parts List is an explanation of Daktronics Exchange and Repair and Repair Programs. Refer to these instructions if replacement components or repair is needed. 2 Introduction

7 1.2 Daktronics Nomenclature To fully understand some Daktronics drawings, such as schematics, it is necessary to know how various components are labeled in those drawings. This information is useful when trying to communicate maintenance or troubleshooting efforts. The label A on a drawing item typically denotes an assembly. An assembly can be a single circuit board or a collection of components that function together, usually mounted on a single plate or in a single enclosure. In addition, the following labeling formats might be found on various Daktronics drawings: TB denotes a termination block for power or signal cable. F denotes a fuse. E denotes a grounding point. J denotes a power or signal jack. P denotes a power or signal plug for the opposite jack. Finally, Daktronics part numbers are commonly found on drawings. Those part numbers can be used when requesting replacement parts from Daktronics Customer Call Center. Take note of the following part number formats. (Not all possible formats are listed here). 0P- - denotes an individual circuit board, such as a driver board. 0A- - denotes an assembly, such as a circuit board and the plate or bracket to which it is mounted. A collection of circuit boards working as a single unit may also carry an assembly label. W- denotes a wire or cable. Cables may also carry the assembly numbering format in certain circumstances. This is especially true for ribbon cables. F- denotes a fuse. T- denotes a transformer. PR- _ - _ denotes a specially ordered part. M- _ denotes a metal part, and 0M- typically denotes a fabricated metal assembly. Introduction 3

8

9 Section 2: Controller Overview Section 2 includes the following subsections: All Sport 100 Overview: identifies the control equipment and how it operates the displays Replacement Parts List: includes the components of the All Sport 100 that may need to be replaced Daktronics Exchange and Repair and Return Programs: covers the procedure for returning equipment to Daktronics and/or requesting new parts 2.1 All Sport 100 Overview The All Sport 100 Series controller, shown in Figure 3, is a hand-held controller designed to operate Daktronics BB-114 portable basketball scoreboard. This lightweight, 6" high by 4 1 / 4 " wide controller is encased in ABS plastic, making it a durable as well as convenient control option. The console s liquid crystal display (LCD) will guide you through the operation of the system. The All Sport 100, identified by the series number AS-100, can be configured to display game time, game scores and possession and bonus information. For details on configuring the All Sport 100 to operate a display, refer to Section 3: Basic Operation. When opening the packages, inspect for shipping damage such as rattles and dents. See that all equipment is included as shown on the packing slip. Immediately report any deficiencies to Daktronics. Save all packing materials for shipping if warranty repair or exchange is needed. Figure 3: All Sport 100 Controller Overview 5

10 2.2 Display Connection A 2-pair, shielded cable at 22 AWG connects the All Sport 100 controller to Daktronics BB-114 portable basketball scoreboards. The cable extends from the XLR jack at the rear of the BB-114 to the 9-pin jack on the top of the controller, as shown in Figure 4. For more information regarding the BB- 114 portable basketball display, refer to Figure 4: Display Connection ED-13315, the BB-114 Portable LED Basketball Scoreboard Installation, Maintenance, and Operation Manual. 2.3 Replacement Parts List The following is a list of possible replacement parts for the All Sport 100 controller. When re-ordering a part, be sure to use its corresponding part number. Part Part Number All Sport 100 controller 0A Cable 0A Clock/score insert LL-2550 Segment timer insert LL-2648 Wall pack transformer T Daktronics Exchange and Repair and Return Programs To serve customers repair and maintenance needs, Daktronics offers both an Exchange Program and a Repair and Return Program. Exchange Program Daktronics unique Exchange Program is a quick service for replacing key parts in need of repair. If a part requires repair or replacement, Daktronics sends the customer a replacement, and the customer sends the defective part to Daktronics. This decreases display downtime. 6 Controller Overview

11 Before Contacting Daktronics Identify these important part numbers: Display Serial Number: Display Model Number: Contract Number: Date Installed: Location of Sign (Mile Marker Number): Daktronics Customer ID Number: To participate in the Exchange Program, follow these steps. 1. Call Daktronics Customer Service: Market Description Schools (primary through community/junior colleges), religious organizations, municipal clubs and community centers Universities and professional sporting events, live events for auditoriums and arenas Financial institutions, petroleum, sign companies, gaming, wholesale/retail establishments Department of Transportation, mass transits, airports, parking facilities Customer Service Number When the new exchange part is received, mail the old part to Daktronics. If the replacement part fixes the problem, send in the problem part which is being replaced. a. Package the old part in the same shipping materials in which the replacement part arrived. b. Fill out and attach the enclosed UPS shipping document. c. Ship the part to Daktronics. 3. A charge will be made for the replacement part immediately, unless a qualifying service agreement is in place. In most circumstances, the replacement part will be invoiced at the time it is shipped. 4. If the replacement part does not solve the problem, return the part within 30 working days or the full purchase price will be charged. If, after the exchange is made the equipment is still defective, please contact Customer Service immediately. Daktronics expects immediate return of an exchange part if it does not solve the problem. The company also reserves the right to refuse parts that have been damaged due to acts of nature or causes other than normal wear and tear. Controller Overview 7

12 Repair & Return Program For items not subject to exchange, Daktronics offers a Repair & Return Program. To send a part for repair, follow these steps: 1. Call or fax Daktronics Customer Service: Refer to the appropriate market number in the chart listed on the previous page. Fax: Receive a Return Material Authorization (RMA) number before shipping. This expedites repair of the part. 3. Package and pad the item carefully to prevent damage during shipment. Electronic components, such as printed circuit boards, should be placed in an antistatic bag before boxing. Daktronics does not recommend Styrofoam peanuts in packaging. 4. Enclose: your name address phone number the RMA number should be written clearly on the outside of the box a clear description of symptoms Shipping Address Daktronics Customer Service PO Box nd Ave Brookings, SD Controller Overview

13 Section 3: Basic Operation 3.1 Console Operation The console face consists of a two-line-by-16-character liquid crystal display and a sportspecific keyboard insert. In most cases, the top line of the LCD shows the main clock time, the direction the clock is counting and when the main horn is sounding. Generally, the bottom line of the LCD displays the home and guest team scores. Throughout this manual, the names or letters of keys on the keyboard are enclosed in angle brackets (such as <ENTER*>). Keys and functions common to all sports are explained in Section 3.5. All of the keys that pertain to a specific sport code insert are explained in detail in the section of the manual for that specific sport. 3.2 All Sport 100 Inserts and Codes Reference Drawings: Insert; A/S 100 Clock/Score Code-01...Drawing A Insert; A/S 100 Insert; Baseball...Drawing A Insert; LL-2648 Segment Timer Code-06...Drawing A Sport inserts are used to allow a single console to control multiple sports. Select the proper insert from the chart below and slide it into the insert opening, on the left side of the console, until it stops. To remove a sport insert, pull on the tab that extends from the left side of the console. The insert will easily slide out. The All Sport 100 uses two different keypad inserts to program game time, segment/practice timing, game score and bonus and possession information into Daktronics BB-114 portable basketball displays. Segment timing is controlled by sport insert LL-2648, and all other data is entered using sport insert LL Figure 5 at right illustrates one AS-100 insert used to control the displays. For more details on the inserts, refer to the All Sport 100 insert drawings, Drawings A , and A , located in Appendix A: Reference Drawings. If an insert is lost or damaged, a copy of the insert drawings are located in Appendix A: Reference Drawings can be used until a replacement is ordered. Figure 5: All Sport 100 Insert LL-2648 Basic Operations 9

14 The All Sport 100 controls the Daktronics BB-144 portable basketball displays. Operation of the displays is discussed in Section 3, Section 4, and Section 5 of this manual. To start up the controller and use the insert, refer to Section 3. Read the section carefully to fully understand the operation instructions. 3.3 Sport Insert Operation Concepts A sport insert identifies keys used in the normal course of operation for a specific sport. In most cases, pressing a key immediately changes the scoreboard. Sometimes a sequence of keys must be pressed before a change takes place on the scoreboard. Keys that require entry of additional information are marked with a dot, for example, <SET >. The additional information required usually is a number followed by the <ENTER*> key. Some keys also include a +1. Pressing one of these keys once increments, or increases, by one the corresponding field on the scoreboard (such as team score or period). A key with -1 decrements, or decreases, the total of a scoreboard field by one. On most inserts, certain keys have been grouped together under the headings Home or Guest. These keys are Team keys, and they work the same for both teams. They affect the statistics only for the specific home or guest team. Keys not under one of these headings are Game keys. They are general keys for the progress of the game, such as period or quarter. Other keys have been blocked together to emphasize that these keys work together. 3.4 Startup ALL SPORT 100 ED ver 1.0 The console performs a self-test when it is powered on. During the self-test, a message displays the standard software loaded in the console. ED = standard software number ENTER CODE 01 clock/score When the self-test completes, the screen displays the last code entered into controller. To select a new sport code: 1. Press <CLEAR> to clear the previous code. 2. Get the code number from the sport insert or the section of the manual for that sport. 3. Use the number keys to enter the new two-digit code. Press <ENTER*>. 10 Basic Operations

15 3.5 Common Sport Keys Start <START> is used to start the main clock Stop <STOP> is used to stop the main clock. Enter/Edit The <ENTER*/EDIT> key has dual functions. This key functions as the enter key when editing game data. Pressing the key will accept the new data and end the edit. If not in Edit mode, the <ENTER*/EDIT> key allows the user to select the item to be edited, such as team score. After pressing the <ENTER*/EDIT> key, the operator presses one of the increment or decrement keys for the desired field on the scoreboard. The operator then simply enters the value he or she wishes to display and presses <ENTER*/EDIT> to accept it. Clear/Alt The <CLEAR/ALT> key has also two functions. The key operates as the clear key when editing game data. Pressing the key will clear the data being edited, or, if pressed twice, will exit the edit. When not in Edit mode the <CLEAR/ALT> key allows the user to access the alternate function keys. Pressing the <CLEAR/ALT> and then one of the alternate function keys will initiate the desired function. Set Time time edit set curr mm:ss.t mm:ss.t = minutes, seconds, tenths of a second After the main clock has been stopped, press <SET TIME > to display the current time of the main clock. To change the time, enter the desired time on the number pad and press <ENTER*>. Press <CLEAR> twice to clear changes and return to the game. Basic Operations 11

16 Count Up/Down MAIN CLOCK-DOWN 1-UP, 2-DOWN Up/down = current direction After the main clock has been stopped, the direction of the clock can be set. Press <ALT>, and press <SET TIME> to move to the main clock menu. Press <1> or <2> to select Up or Down (default). Notes: The current direction of the main clock is shown on the top line of the LCD with an up ( ) arrow to show count up and a down ( ) arrow to show count down. The <COUNT UP/DOWN > function is disabled while the clock is running. Auto Horn AUTO HORN-ON h 1-ON, 2-OFF on/off = current setting To get to the Auto Horn menu, press <ALT>, and then press <AUTO HORN>. h appears on the upper right corner of the LCD when the Auto Horn is enabled. An up/down ( ) arrow also appears to indicate clock direction. Press <1> or <2> to select On (default) or Off. 12 Basic Operations

17 Manual Horn Press <MANUAL HORN> to sound the main horn. The horn sounds as long as the key is pressed. The horn stops sounding when the key is released. Dimming Dimming Level (0-3): none <0> = none (bright) <1> = 2/3 (dim) <2> = 1/2 (dimmer) <3> = 1/3 (dimmest) Press <0>, <1>, <2> or <3> to select the intensity for the digits on the scoreboard. Press <ENTER*> to accept the new dimming level. 13 Basic Operations

18

19 Section 4: Clock/Score Operation Reference Drawing: Insert; A/S 100 Clock/Score Code-01...Drawing A The All Sport 100 controller enters Clock/Score information into Daktronics BB-114 portable scoreboards using sport insert LL-2550, shown at right in Figure 6. If this insert is lost or damaged, a copy of the insert drawing, Drawing A , can be used until a replacement can be ordered. Refer Section 3 for information on starting the console and for instructions for use of the sport insert. Read the Basic Operation material carefully to fully understand the following operating instructions. This section provides instructions for using the All Sport 100 controller to program game time and game score into Daktronics BB-114 displays. To run the Clock/Score insert for the BB-114 scoreboard, enter Code 01 at the Enter Code command. Figure 6: Clock/Score Insert LL Clock Keys Set Time The current time on the main clock is displayed by pressing <SET TIME > and it can be changed by entering the desired time on the number pad and pressing <ENTER*>. The default period length can be edited by pressing <SET TIME > a second time. time edit set curr mm:ss.t* mm:ss.t = minutes, seconds, tenths of a second To display the current clock time, press <SET TIME >. To change the current clock time, enter the new time in minutes and seconds on the number pad and press <ENTER*>. Press <CLEAR> twice to clear changes and return to the game. Clock/Score Operations 15

20 Time edit edit Period mm:ss.t* mm:ss.t= minutes, seconds, tenths of a second To display the configured time for period length, press <SET TIME > twice. To accept the period length as the new clock time, press <ENTER*>. To decline the selection of the period length, press <CLEAR>. To change the period length and set the main clock, enter the new time in minutes and seconds using the number pad and press <ENTER*>. Press <CLEAR> twice to clear changes and return to the game. Period +1 Period: edit 2 Press <PERIOD+1> to increment the total. The LCD shows which key was pressed and the new value. To edit the period, press the <ENTER*/EDIT> key followed by <PERIOD + 1> and then enter the desired number on the keypad. Press <ENTER*/EDIT> to accept the number. 16 Clock/Score Operations

21 4.2 Score Keys This section discusses the All Sport 100 controller keys used to input game score, bonus, and possession information into the BB-114 portable basketball scoreboard. Home/Guest Score Keys These scoring keys allow the user to increment the game score by one or two points at a time. Refer to the tables on the following page for instructions on the use of the Home/Guest Score keys. The tables use home as an example, but the instructions are the same for both Home and Guest. Time mm:ss.t h h= 0 g= o MM= minutes SS= seconds T= tenths of a second This screen shown at left is the default screen for the Clock/Score All Sport insert. The initial game score for both teams is zero. Home score +1 1 Time :56.0 h= 1 g= o To add points to the home team score, press <HOME SCORE +1>.This key changes the home team score by adding one point. The screen at right appears. <HOME SCORE +2> operates similarly to the <HOME SCORE +1> key, as it adds two points to the home team score instead of one. Home score -1 0 To subtract points from the home team score, press <HOME SCORE -1>. This key changes the score by subtracting one point. Bonus Keys These two keys on the All Sport 100 is used to program bonus and possession information into the BB-114 scoreboard. When either home Bonus or Guest Bonus is selected, the controller sends the signal to the scoreboard and the corresponding bonus indicator illuminates. The table uses home as an example, but the instructions are the same for both Home and Guest. Clock/Score Operations 17

22 Home bonus On Pressing the <BONUS > key toggles bonus information on and off for the home team. To program bonus for the home team, press the <BONUS > key once. Home bonus Off To clear entered bonus information, press the <BONUS > key again. Possession Key This All Sport 100 key is used to send possession information to the BB-114 scoreboard. When either home possession or guest possession is selected, the controller sends the signal to the scoreboard, and the corresponding possession indicator illuminates. guest possession home possession Pressing the <POSSESSION > key toggles between home and guest possession. Each of the corresponding screens to the left will appear, depending upon how many times you press the <POSSESSION > key. Press the <POSSESSION > key to toggle between home and guest possession indicators. 18 Clock/Score Operations

23 Section 5: Segment Timer Operation Reference Drawing: Insert; LL-2648 Segment Timer Code-06...Drawing A The All Sport 100 enters segment timing information into the Daktronics BB-114, TI-2025 and TI-2026 displays using sport insert LL-2648, shown in Figure 7. If this insert is lost or damaged, a copy of the insert drawing, Drawing A , can be used until a replacement can be ordered. Refer Section 3 for information on starting the console and for instructions for use of the sport insert. Read the Basic Operation material carefully to fully understand the following operating instructions. This section provides instructions for using the All Sport 100 controller to program segment timing into Daktronics BB-114, TI-2025 and TI-2026 displays. To run the segment timer for these displays, enter Code 06 at the Enter Code command. 5.1 Segment Timer Information Figure 7: Segment Timer Insert LL-2648 The segment timer is used to time events such as practice sessions. The operation of the segment timer is determined by 40 segments of pre-programmed length. The segment timer will count down starting at the segment number that is set as First Segment. When the first segment is completed, the segment timer will count the Interval Time and proceed with the next segment. The timer will continue counting segments until the segment number that is set as Last Segment is counted down. It then will reset to the segment saved as the First Segment and will either begin counting down or pause for the <START> key to be pressed, depending on the Auto Stop At Last Seg setting. To stop the timer after each segment is completed, use the Auto Stop feature. The First Segment and Last Segment values can be used to set up specific practice sessions. For example, the practice session for one sport could be programmed to use segments 1-10, while another might use segments Set the First Segment and Last Segment values to the desired segment numbers for the session and the console will count down each of the segments in order, either stopping on the last segment or looping through included segments again, based on the Auto Stop At Last Seg setting. The default First Segment value is 1. The default value for the Last Segment is 40. Segment Timer Operation 19

24 5.2 Segment Timer Keys Main Screen SEGMENT: 5 TIME: 5:00 h P2 h / h = count up/count down P2 = program number The main screen, displays which segment number is active and the amount of time for which that segment is programmed. It also shows the program number and the direction the clock is counting. First/Last Segment FIRST SEG XX LAST SEG YY XX = current first segment YY = current last segment Press the <FIRST/LAST SEG> key. This setting determines the first and last segment in a range of segments to run when <START> is pressed. Enter the First Segment value and press <ENTER*> to set. Enter the Last Segment and press <ENTER*> to set and exit. The console will be reset to the segment saved as First Segment when the <RESET TO 1ST SEG> key is pressed. The console will automatically reset to the segment saved as First Segment after the segment saved as Last Segment is completed. Segment Number/Time SEGMENT: xx TIME EDIT xx = segment number SEGMENT: xx TIME EDIT nn:nn xx = segment number nn:nn = segment time Press <SEG NO /TIME > to set individual segment times. Enter the segment to be edited and press <ENTER*>. Enter the time for the segment and press <ENTER*> to accept and move to the next segment time. Press <ENTER*> again to exit the function. 20 Baseball Operation

25 Set Program CURRENT PROG: 2* Select = current setting The segment timer has the ability to select between 7 programs. Program information is saved when powered down. Press <SET PROGRAM> to change the current program. Select the desired program with the number pad and press <ENTER> to accept the changes. Programs 1-5 allow a unique program for each weekday. (Monday through Friday) Program 6 is dedicated to a Play Clock. Program 7 is dedicated to a Two-Minute Drill. Interval Time INTERVAL TIME: nn:nn nn = current setting The interval time is the time between each segment. Press <INTERVAL TIME > to display the current value of interval time on the bottom line of the LCD. Edit the value of the interval time and press <ENTER*>. DISPLAY INTERVAL 1 YES 2*NO * = current setting If the interval time is set to 00:00, no interval time will be counted. This setting determines whether the interval count will be displayed on the scoreboard. Press <1> to display the interval time on the scoreboard. Press <2> to disable the interval time display. The interval time will be displayed only on the console. Notes: Regardless of this setting, the value saved in interval time will be counted down between segments. Set the interval time to 0 (zero) if no interval between segments is desired When the interval time is being displayed, the segment number on the scoreboard flashes to indicate that the time displayed is interval time. To disable the segment number flash, set the display interval to NO (<2>). Segment Timer Operation 21

26 Copy Range COPY: nn:nn* SEG xx to yy nn:nn = segment value to be copied xx = starting segment value yy = ending segment value Press <COPY RANGE > to set a range of segments to a specific value. All segments from xx to yy (inclusive) will be set to the value specified by nn:nn. Enter the value specified by the asterisk and press <ENTER*> to move to the next field. Auto Stop STOP AT EACH SEG 1*YES 2-NO *= current setting This setting determines the operation of the console when each segment is completed. Press <1> to set the console to stop after each segment is completed. Wait for the <START> key to proceed with the next segment. Press <2> to set the console to automatically begin the next segment when each segment is completed. STOP AT LAST SEG 1*YES 2 NO * = current setting If the setting of Auto Stop At Each Seg is NO, the console will prompt for the Auto Stop At Last Seg setting. Press <1>or YES to set the console to stop when the last segment has been completed. Press <2> or NO to set the console to start over at the first segment when the last segment is completed Warning Time Warning time 0:00 0:00 = default Press <WARNING TIME >, enter the time in minutes and seconds and press <ENTER*>. Enter 00:00 for no warning time. When the warning time is reached, the segment number flashes until the main clock reaches zero. 22 Baseball Operation

27 Reset Current Segment Press <RESET CURRENT SEG> to reset the segment time to the value specified by the current segment. The segment number will remain at the current value. Edit Current Segment SEGMENT: 2 h TIME: 5:00 P1 CURRENT SEGMENT EDIT 02* * = current setting Press <CURRENT SEGMENT + 1> to increment the segment number by one. Press <EDIT> <CURRENT SEGMENT +1> to display the current segment for editing. Enter the new value for the current segment number and press <ENTER*>. Reset to First Segment Press <RESET TO 1ST SEG> to reset the segment number and segment time to the values saved as the first segment. Note: The Reset to First Segment function is disabled while the clock is running. TI-2025/2026 Segment Timer Model TI-2025/2026 and TI-2010 include control option 0A Drawing A depicts the system set up. Send Program Information to Display TRANSFERING DATA PLEASE WAIT Using the All Sport 100 controller, the user enters the information for programs 1 to 7. Press <ALT> and then press <SEND>. The LCD screen will display transferring data. TRANSFER COMPLETE Wait for approximately 5 seconds until the screen displays transfer complete, and returns to the main menu. The TI- 2025/2026 will show PPPP on the digits if program was received successfully. This indicates the information has been stored into the TI-2025/2026. The All Sport can now be unplugged, and the displays can be remotely controlled by the RC-50. Segment Timer Operation 23

28 TI-2025/2026 Play Clock (Segment Timer Program 6) Program 6 is dedicated to a play clock. The play clock can be set up to 99 seconds using the <SET TIME> key. SET PLAY CLOCK 0:25* Using the All Sport 100 controller, set the program to 6. Press the <SET TIME> key. Enter a time using the number keys and press enter to accept the changes. PLAY CLOCK TIME: 0:25 P6 Press <START> to start the play clock. Press <STOP> to stop and reset the play clock. TI-2025/2026 Two-Minute Drill (Segment Timer Program 7) Program 7 is dedicated to a Two-Minute Drill clock. This program consists of two different clocks: the two minute game clock and the 25 second play clock. Press <START> to start the game clock. Press <STOP> to stop the game clock. Press <CURRENT SEGMENT +1> to start the play clock. Press <CURRENT SEGMENT +1> again to stop and reset the play clock. PLAY: 0:25 MAIN: 2:00 P7 Using the All Sport 100 controller, start the main clock with <START> and stop the main clock with <STOP>. Start the play clock with <CURRENT SEGMENT +1>. Press <CURRENT SEGMENT +1> again to stop and reset the play clock. 24 Baseball Operation

29 RC-50 Segment Timer Controls (Programs 1-5) < START > < STOP > < RESET PROGRAM > < RESET SEGMENT > < PROGRAM + > < SEGMENT + > < HORN > < SEGMENT > Figure 8: RC-50 Label LL-2649 Note: Control operations are exclusive; the All Sport 100 must be unplugged for the RC-50 to function. RC-50 Play Clock Controls (Program 6) The unique controls for program 6 are listed below. < STOP > This button stops and resets the play clock. RC-50 Two-Minute Drill Controls (Program 7) The unique controls for program 7 are described below. < START > Starts the game clock. < STOP > Stops the game clock. < SEGMENT + > Starts the play clock. < SEGMENT > Stops and resets the play clock. The status indicator light indicates the clock is running. Figure 9: TI-2025/TI-2026 Segment Timer Operation 25

30

31 Section 6: Baseball Operation The sport insert drawing is located in Appendix A. If an insert is lost or damaged, a copy of the insert drawing can be used until a replacement can be ordered. Refer Section 3 for information on starting the console and for instructions for use of the sport insert. Read the Basic Operation material carefully to fully understand the following operating instructions. Use code 03 on the All Sport 100 for baseball. 6.1 Baseball Keys Out +1, Inning +1 The <OUT +1> and <INNING +1> keys are used to increment their respective totals. Inning +1 nn nn = current setting Press <OUT +1> or <INNING +1> to increment their respective totals. The LCD shows which key was pressed and the new value. To change values, first press <EDIT> and <OUT +1> or <INNING +1> to display the current setting. Enter the correct number on the number pad and press <ENTER*>. Baseball Operation 27

32 Ball, Strike, Clear Ball/Strike The <BALL +1> and <STRIKE+1> keys increment the ball and strike digits. Pressing the <CLEAR BALL & STRIKE>key clears the digits. Note: If the ball count value is 4 when <BALL +1> is pressed, the value is blanked out. If the strike count value is 3 when < STRIKE +1> is pressed, the value is blanked out. Ball: +1 N Press the <BALL +1> or < STRIKE +1> to increment the ball and strike digits. Press the <CLEAR BALL & STRIKE> key to clear the digits to zero. Hit, Error The <HIT> and <ERROR> keys are used to turn on the Hit or Error indicator or digits in the table that follows, <ERROR> is used as an example. Error: ON Press the <HIT> or <ERROR> key to turn on the hit or error indicator or digits. This display appears briefly. Home/Guest Score +1, -1 The <HOME SCORE +1> and <HOME SCORE -1> and <GUEST SCORE +1> and <GUEST SCORE -1> keys are used to increment or decrement their respective totals. Team score: +1 HOME nn nn = current setting Press the appropriate home or guest <SCORE +1> or <SCORE -1> key to increment or decrement the total number of runs for the team. The LCD shows which key was pressed and the new value for the corresponding team. The <EDIT> key permits the user to select and edit Runs +1 or 1. First, press <EDIT> and the key for the home or guest field to be edited, then enter the correct number on the number pad and press <ENTER*>. 28 Baseball Operation

33 Appendix A: Reference Drawings The Daktronics drawing number is located in the bottom right corner of the drawing. This manual refers to drawings by listing the last set of digits and the letter preceding them. Insert; A/S 100 Clock/Score Code-01...Drawing A Insert; A/S 100 Insert; Baseball...Drawing A Insert; LL-2648 Segment Timer Code-06...Drawing A Reference Drawings 29

34

35 CODE 01 CLOCK/SCORE LL-2550 REV 02

36 CODE 03 BASEBALL LL-2572, REV 01

37