Steering wheel ADJUSTING THE STEERING WHEEL. Entry and exit mode

Transcription

1 Steering wheel ADJUSTING THE STEERING WHEEL E91122 WARNING Never adjust the steering wheel position whilst the vehicle is in motion. Doing so will reduce control of the vehicle and may cause unpredictable steering movements. CAUTION Do not use steering wheel mounted security devices, as movement of the steering wheel in entry and exit mode, could result in damage to the vehicle or possible injury to the occupant. The steering wheel can be adjusted for tilt and reach, as follows: 1. Turn the switch to the COLUMN or AUTO position. 2. Move the switch forwards or rearwards to adjust reach. 3. Move the switch up or down to adjust tilt. Two steering wheel positions can be stored and recalled by the driver position memory system. The message centre will indicate which switch position has been selected by displaying the message COLUMN ADJUST or COLUMN ADJUST AUTO. Entry and exit mode Entry and exit mode provides automatic movement of the steering column, to allow easier entry to, or exit from, the vehicle. Entry and exit mode is selected by setting the steering column adjustment switch to the AUTO position. Exit: If the driver's door is opened, the steering column will move to the uppermost tilt position, unless already in that position. Entry: When the door is closed and the ignition is switched on, the steering column will return to its previous position. Note: If the steering column switch is moved away from AUTO when the steering column is in the Exit position, the steering column will move back to its previous (driving) position, when the driver's door is closed and the ignition is switched on. If the steering column position is manually adjusted during Entry or Exit operation, steering column movement will stop. 67

2 HORN Climate External 12 C Auto Auto 21.5 C 21.5 C Settings A/C Temp. sync. Auto OFF E91123 The dual tone horn is operated by pressing the centre pad on the steering wheel. The horn also operates as the alarm sounder, if the vehicle alarm system is activated. HEATED STEERING WHEEL The heated steering wheel is activated via the touch-screen main Home menu. 12 : 26pm E94700 The heated steering wheel can also be activated via the Climate menu on the touch-screen. With the engine running, touch the steering wheel icon to turn the heating on or off. Home External 15 C Audio/TV Climate Phone Navigation Vehicle Left Right 20 C C DAB radio DAB1 BBC 5Live Xtra BBC National DAB TA-FM DAB-i Subch. PL II Valet E94699 With the engine running, touch the steering wheel icon to turn the heating on. The icon will glow red when the steering wheel heater is on. 68

3 AUDIO CONTROL E Rotate (up or down) to increase or decrease volume. 2. Rotate (up or down) and release, to scroll up or down through preset radio stations or CD tracks. Rotate and hold (for two seconds) to select the next or previous radio station on the waveband, or to select the next or previous loaded CD (on multi-disc CD players). 3. Press repeatedly to scroll through the audio source options, comprising: FM1, FM2, AM, CD, DAB radio, Auxiliary input and Portable Audio Interface options. Press and hold (for two seconds) to select Phone Ready mode. 4. Press to mute the audio unit. Press to answer or end a phone call. VOICE CONTROL control provides a safe and convenient way of operating certain vehicle systems, without the need to operate the controls manually. This enables you to concentrate fully on driving the vehicle and removes the need to divert your attention from the road ahead, in order to change settings or receive feedback from systems. A number of voice commands are available and, with a little experience, you will find them easy and convenient to use. Jaguar allows for voice activation of the phone, navigation and touch-screen display systems, as well as providing a notepad facility, to allow voice notes to be recorded. Help and tutorial functions provide advice on operating the system. Information on Jaguar operation of the telephone system is detailed later in this handbook. See TELEPHONE VOICE CONTROL (page 312). Information on Jaguar operation of the navigation system is given later in this handbook. See USING VOICE CONTROL (page 362). E95902 The system is controlled using the voice button on the steering wheel (arrowed). commands are picked up by a dedicated microphone and audible feedback will be heard through the audio system speakers. 69

4 Activating the system To activate voice control, press the voice button on the steering wheel. A tone will be heard and LISTENING will be displayed in the message centre, to indicate that the system is now waiting for a voice command. Note: It is only necessary to press the voice button at the beginning of each voice session. Language and accent feedback is given in the same language as is set for recognition. For example, if the recognition language is set to UK English, the system will not recognise other languages (e.g. US English). The language for the system can be changed using the touch-screen as follows: E96024 Operating guide Command list Add phone nametags language English UK Feedback Volume Change Settings 1. From the Home menu, select Comms. 2. From the Comms menu, select and then select Settings. 3. Select Change, then select the desired language from the options available. Note: Changing the recognition language will not affect the language settings for the touch-screen. Giving a command Note: If background noise is excessive (e.g. driving with windows open), the voice system may not recognise a given voice command. Press and release the button on the steering wheel and, after the tone, say one of the commands listed later in this section, or one of the commands given in either the Telephone voice section or the Navigation voice section, as appropriate. See TELEPHONE VOICE CONTROL (page 312). See USING VOICE CONTROL (page 362). Note: Always wait until the tone finishes sounding before giving a voice command. Give commands while facing forwards, in a natural speaking voice as if talking to a passenger or on the phone. Most accents are understood without difficulty, but if the system does not recognise the command, the system will respond with SORRY and allow two more attempts to say the command. The system will repeat the command (as understood by the system) back to you as confirmation. The command will then be acted on or the system will ask for further information - always wait until after the tone has sounded before speaking. Once you are familiar with system requests, it is possible to skip to the end of the request (to when the tone sounds) to give your response. To achieve this, briefly press and release the voice button on the steering wheel during the system request. Note: If the button on the steering wheel is pressed before the system is ready to receive a command, VOICE NOT READY will be displayed in the message centre. 70

5 Cancelling voice control To cancel a voice command, press and hold the button on the steering wheel until a double tone is heard. Note: If a phone call is received during a voice session, voice control is cancelled. system tutorial To listen to a tutorial on how to use Jaguar, press and release the voice button and, after the tone, say VOICE TUTORIAL. The tutorial is divided into four lessons and has a total duration of approximately four minutes. The tutorial can only be undertaken with the vehicle stationary and parked. To cancel the tutorial, press and release the button and say CANCEL. To skip to the previous or next lesson of the tutorial, press and release the button and say PREVIOUS or NEXT. Command help For a list of the most commonly used voice commands, press and release the button and, after the tone, say the appropriate command from the following list: VOICE HELP NAVIGATION HELP PHONE HELP DISPLAY HELP NOTEPAD HELP Settings Operating guide Command list Add phone nametags To give a voice command briefly press the voice button and speak normally after the tone Tutorial will help you start to use your voice control system Tutorial E96025 The tutorial can also be accessed via the touch-screen. 1. Select Comms from the Home menu. 2. From the Comms menu, select. 3. From the menu, select Operating guide and then select Tutorial. 71

6 Full command list A full list of voice commands available can be accessed on the touch-screen. Settings Notepad Phone Select a system for the list of voice commands Operating guide Command list Add phone nametags Phone help Phone reject calls Comms Navigation Display Select a system for the list of voice commands Phone accept calls Phone dial number Phone redial JAG0899 E Select Comms from the Home menu. 2. From the Comms menu, select. 3. From the menu select Command list. 4. Select Navigation or Display to view the relevant command list or select Comms to view the options available. If Comms was selected, you can now choose which system s command list you wish to view (, Notepad or Phone) 1. Select the appropriate system (Phone in this example). 2. Scroll down to view the entire command list for the chosen system. Nametags Nametags allow the voice system to be personalised with the addition of names for phone numbers and navigation locations, destinations and waypoints. A nametag can be any unique name chosen by the user. Details for storing and using nametags in conjunction with the telephone and Navigation systems, are given later in this handbook. See TELEPHONE VOICE CONTROL (page 312). See USING VOICE CONTROL (page 362). A spoken list of currently stored nametags can be heard by pressing and releasing the button and saying PHONE PLAY DIRECTORY or NAVIGATION PLAY DIRECTORY, as appropriate. 72

7 Notepad The notepad facility enables the user to record a note, up to a maximum of 30 seconds duration, which can be subsequently recalled. Note: To hear information on notepad commands, press the button, wait for the tone to sound and then say NOTEPAD HELP. Recording a note 1. Press and release the button, wait for the tone to sound, then say RECORD NOTE. 2. Say the words of the note to be recorded, then press and hold the button to end and save the note. Note: The maximum length of a note is 30 seconds, after which time the recording of the note will be ended automatically. Playing a note Press and release the button, wait for the tone to sound, then say PLAY NOTEPAD. If multiple notes are stored on the system, press and release the button during playback and say NEXT, to skip to the next note. Deleting notes To delete an individual note, press and release the button during playback of the note to be deleted and say DELETE. To delete all notes stored on the system, press and release the button and say CLEAR NOTEPAD. volume adjustment The volume level for voice recognition can be adjusted independently, either by using the steering wheel controls or using the touch-screen: Press the voice button on the steering wheel, to initiate a voice session. Use the volume control thumbwheel on the steering wheel to adjust the volume, as required. Select Vehicle from the touch-screen Home menu, then select Veh. settings. Find the correct entry from the menu of infotainment volume settings and adjust as required. commands This is a list and a description of the basic commands used to operate the system. A list and description of telephone and Navigation system commands, is detailed later in this handbook. See TELEPHONE VOICE CONTROL (page 312). See NAVIGATION SYSTEM VOICE COMMANDS (page 363). Command VOICE HELP Description Plays information on operating the system. VOICE TUTORIAL Initiates a four-part tutorial on use of the system. DISPLAY HELP Plays information on touch-screen display voice commands. DISPLAY SHOW PHONE The Phone menu is displayed on the touch-screen. 73

8 Command DISPLAY SHOW NAVIGATION DISPLAY ON DISPLAY OFF NOTEPAD HELP RECORD NOTE PLAY NOTEPAD Description The Navigation main menu is displayed on the touch-screen (the navigation caution must be accepted before the menu is displayed). Turns the touch-screen on. Turns the touch-screen off. Plays information on notepad commands. Allows recording of a note, up to 30 seconds long. Plays all currently stored notes. CLEAR NOTEPAD Deletes all notes currently stored in notepad. CRUISE CONTROL 1 E SET - Rotate and release to engage cruise control (at the vehicle's current speed). With cruise control operating, rotate up or down to increase or decrease the speed in 2 km/h (1 mph) steps. 2. CANCEL - Press to cancel cruise control. The previously programmed set speed will be retained and can be reselected by pressing RESUME. 3. RESUME - Press to resume the previously programmed set speed (e.g. after cruise control has been cancelled). 4. GAP (ACC only) - Rotate up or down to increase or decrease the time gap to the vehicle ahead. The gap can be set to one of four pre-defined intervals. The current setting will be displayed in the message centre. For more information about cruise control: See USING CRUISE CONTROL (page 153). For more information about adaptive cruise control (ACC): See USING ACC (page 156). 4 74