Clean Up Team Lab 10 Points. Cisco Switch Lab I Individual Lab 25 Points

Transcription

1 All of the work in this project is my own! I have not left copies of my code in public folders on university computers. I have not given any of this project to others. I will not give any portion of this project to others taking this class. I realize that the penalty for turning in work that is not my own can range from an "F" in the class to dismissal from Trinity University. Print Name Time Spent =. Hrs. Signature (pledged) Clean Up Team Lab 10 Points Team # = 1] {Initial/Pledge} I have no more than 1-2 ft of cat 6 wire connecting our Red Dell to the wall; if more I will cut and re-end the connection. My wiring works perfectly! 2] {Initial/Pledge} I have no more than 1-2 ft of cat 6 wire connecting my Black Dell to the rack; if more I will cut and re-end the connection. My wiring works perfectly! 3] {Initial/Pledge} There are no un-necessary wires sticking out of the wire track behind our team s wall. 4] {Initial/Pledge} The numbers on the Wire Track Covers (behind our team s wall) match the numbers on the of the Wire Tracks. Cisco Switch Lab I Individual Lab 25 Points Disconnect all wires from your switch (except the power). Power off your switch. Power on your switch. If the switch has an uplink to the Internet, disconnect it! You may connect to the Switch Console using Mac, Linux, or Windows. Code To Reset Cisco Switch To Factory Defaults delete flash:vlan.dat How to Reset a Cisco Catalyst 3550 / 3560 Switch to Factory Defaults Enter the following commands in the privileged mode: (# prompt) Switch#delete flash:vlan.dat Delete filename [vlan.dat]? Delete flash:vlan.dat? [confirm] erase startup-config Switch#erase startup-config Erasing the nvram filesystem will remove all configuration files! Continue? [con firm] [OK] Erase of nvram: complete

2 Cisco-Switch-Lab-1.docx CSCI-3342 Initials Page 2 Switch# 00:04:46: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram reload If you are prompted to save anything before reloading, respond by saying no. TAKE A MOMENT & READ THROUGH THIS LAB. ANSWER QUESTIONS AS YOU WATCH VIDEOS. 1] {Initial/Pledge} I have watched the C3350-Switch-Overview.mp4 Video 2] Find one of the cables above at amazon.com. It is a USB to _?_ cable. Find one of them at amazon.com 3] $ What is the cheapest prime cost you can find for the cable above. 4] Find one of the cables above at amazon.com. It is a Cisco C_?_ cable. Find one of them at amazon.com 5] $ What is the cheapest cost (include shipping) you can find for the cable above. 6] {Initial/Pledge} I have watched the Basic-Cisco-Switch-Configuration.mp4Video 7] The _?_ prompt indicates that we are in normal mode. 8] The _?_ prompt indicates that we are in privilege mode. 9] The _?_ prompt indicates that we are in global configuration mode. 10] Write the Cisco command to get from normal mode to privilege mode. 11] Write the Cisco command to get from privilege mode to normal mode.

3 Cisco-Switch-Lab-1.docx CSCI-3342 Initials Page 3 1] {Initial/Pledge} I just ran the code to Reset the Switch to Factory Defaults (shown in green above)! 2] {Initial/Pledge} Whenever asked for passwords, use cisco for everything! 3] {Initial/Pledge} I know that I am welcome to run through the initial configuration dialog with the video if I like, but if I have done so, I need to do a Reset the Switch to Factory Defaults and select No to the initial configuration dialog before continuing this lab! 1] Write the Cisco command to get from privilege mode to global configuration mode. 2] Write the Cisco command to get from global configuration mode to privilege mode. 3] You are in global configuration mode; what happens when you type ho (and then hit the Tab Key)? 4] In order to rename the switch, one has to be in {normal/privilege/global configuration} mode. Indicate all that apply. 5] Write the Cisco command to name your switch Switch-TH use your initials 6] The Cisco switch is a layer _?_ switch. 7] Why would we want to assign a layer 3 IP Address on a layer 2 switch? 8] You have changed the hostname on your system. This change was made to the running-config file. Write the Cisco command to display the contents of this file on the terminal. 9] In order to display the contents of the running-config file, one has to be in {normal/privilege/global configuration} mode. Indicate all that apply.

4 Cisco-Switch-Lab-1.docx CSCI-3342 Initials Page 4 10] {T/F} Once I change the hostname in the running-config file, it will remain changed when I unplug the switch and then restart it. [TRY THIS] 11] Write the Cisco command to transfer the contents of the running-config file to the startup-config file. 12] {T/F} Once I copy configuration changes fro the running-config file to the startup-config file, changes will remain changed when I unplug the switch and then restart it. [TRY THIS] 13] You have changed the hostname on your system. This change was transferred to the startup-config file. Write the Cisco command to display the contents of this file on the terminal. 14] Write the Cisco command to display what type of device you are on. 15] What switch is illustrated in the version dump above? 16] What operating system is illustrated in the version dump above? 17] How long has the switch, illustrated in the version dump above, been running? 18] Write the Cisco command to display all of the interface information about fa1/10? 17] In order to display the version information, one has to be in {normal/privilege/global configuration} mode. Indicate all that apply.

5 Cisco-Switch-Lab-1.docx CSCI-3342 Initials Page 5 20] Write the Cisco command to display all of the interface information about all of the interfaces? 21] In order to display the interface information, one has to be in {normal/privilege/global configuration} mode. Indicate all that apply. Connect a Laptop/Desktop (that is configured for DHCP) to one of the Ports in the Switch 1] Write the Cisco command to display the dynamic mac address table? 2] Write the Cisco command to display the static mac address table? 3] In order to show the mac address information, one has to be in {normal/privilege/global configuration} mode. Indicate all that apply. 4] Some of the Cisco switches have these ports. What are they for? 5] How does the item above relate to our Cisco switches? 6] POE is an acronym for _?_ 7] {T/F} The C3550 switch supports POE. 8] One of the videos show you two POE device that one might use with a switch. What were they?

6 Cisco-Switch-Lab-1.docx CSCI-3342 Initials Page 6 9] {T/F} The up and down arrow keys queue switch commands. What To Turn In 1] This lab sheet with at least 90% of the questions answered correctly. 2] Sign, Pledge, & Record the amount of time No Lab Is Complete Until Both Are Complete ] You sign & submit the Pledge form. a) Review the Pledge statement b) Sign & Pledge c) Record the amount of time you think you spent on this lab d) Staple all pages of this lab. Fold in half length-wise (like a hot-dog). Put your name on the outside. Place it on the professor desk before the beginning of lecture on the day it is due. The penalty for late homework will not exceed 25% off per day. 2] Place all programming code associated with this program, if any, in the Professor s Code Drop Box a) I do not accept programs by mail; do not submit labs via ! Comments A] Programs that do not compile are worth little, if anything. B] If a print statement format is off, the penalties will often be less than the 25% per day late penalty; turn in the lab. You would not be happy if you went to Best Buy and purchased a large screen TV that did everything except show the picture; you would consider it pretty worthless. Most users consider software that does not work properly pretty useless as well. If the lab is not working correctly, credit will be small (if any); you might be better to accept a 25% (1 day) late penalty and turn in the lab working correctly! C] Start all programs early so that you can get in contact with the professor if you have problems. D] If you are turning in this lab late, you may hand it to me if I am in the office put it in the mail box outside my office door slide it under the outer door to our suite {if locked} slide it under my office door. The sooner I get late labs, the sooner the late penalty meter quits clicking. E] Backup your programs in at least three places. Put a copy on your Y drive. Put a copy on your flash drive. Put a copy on your personal computer. Send yourself a copy in your .