STATE OF FLORIDA DEPARTMENT OF TRANSPORTATION. Contract plans. Intelligent transportation systems plans

Transcription

1 INDEX OF PLANS SHEET Contract plans A-1 UPGRADE - PHASE II KEY SHEET A-2 GENERAL NOTES A-3 MAP A-4 INSTALLATION NOTES A-5 A-6 EQUIPMENT INSTALLATION & CUT-OVER SEQUENCING NOTES A-7 PROPOSED NETWORK CONFIGURATION H-1 H-42 HUB SITES S-1 S-6 SPUR SITES R-1 R-24 REPEATER SITES T-1 T-32 TURNPIKE SITES E-1 E-4 EQUIPMENT DETAILS STATEWIDE ITS COMMUNICATIONS PROJECT Intelligent transportation systems plans NOTE: THE SCALE OF THESE PLANS MAY HAVE CHANGED DUE TO REPRODUCTION. STATEWIDE ITS Communications NETWORK UPGRADE PROJECT PHASE II GOVERNING STANDARDS AND SPECIFICATIONS: FLORIDA, DESIGN STANDARDS, CURRENT EDIITON, AND STANDARD SPECIFICATIONS R ROAD AND ENGINEER OF RECORD: TERRY POSEY, P.E. BRIDGE CONSTRUCTION, CURRENT EDITION, AS AMENDED BY CONTRACT DOCUMENTS. FDOT PROJECT MANAGER: RANDY PIERCE P.E. NO.: FLORIDA UPGRADE PHASE II KEY SHEET A-1 \\dotscoteo1\traffic_ops_data\public\tsmo\telcom\\ Technology Replacement Plan\Phase 2 Contract Plans\Contract Plans\1-Notes\A-Notes vsd Attachment 1 1

2 PROJECT : THESE PLANS AND TECHNICAL SPECIFICATIONS DELINEATE THE REQUIREMENTS R UPGRADING THE STATEWIDE ITS COMMUNICATIONS NETWORK () BY REPLACING ITS AGING NORTEL PASSPORT MULTI-SERVICE SWITCHES, ASN ROUTERS, BPS2000 SWITCHES, AND ETHERNET HUBS, WITH NOKIA 7705 SAR18 MULTIPROTOCOL LABEL SWITCHING (MPLS) DATA TRANSPORT EQUIPMENT. THIS PROJECT WILL SUPPLY, INSTALL, CONFIGURE, AND INTEGRATE NOKIA 7705 SAR18 SERVICE AGGREGATION ROUTERS WITH THE S EXISTING HARRIS DVM6-45 TDM MICROWAVE BACKBONE TO ENABLE CUT-OVER OF ITS TRAFFIC STATEWIDE, WITH MINIMAL IMPACT TO THE FDOT S OPERATIONS. THE VENDOR SHALL REFER TO THE TECHNICAL SPECIFICATIONS, CONTRACT PLANS, AND EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST R DETAILED S OF THE SITES OF WORK, INSTALLATION REQUIREMENTS, PROVISIONING OF DATA SERVICES, AND INTERFACE REQUIREMENTS. THE VENDOR SHALL SUPPLY AND CONFIGURE A 7705 SAR-18 R EACH NODE. THE NEW MPLS NETWORK EQUIPMENT SHALL BE COMPATIBLE WITH THE MPLS LOW-LEVEL NETWORK DESIGNS ALREADY IMPLEMENTED IN THE FLORIDA KEYS MICROWAVE PROJECT AND THE DISTRICT 5 RTMC EXPANSION PROJECT, INCLUDING SEAMLESS INTEGRATION OF FDOT S MANAGEMENT AND ITS TRANSPORT SERVICES. THE LOW-LEVEL DESIGNS AND EQUIPMENT CONFIGURATION PARAMETERS R THE EXISTING PROJECTS WILL BE PROVIDED TO THE AWARDED VENDOR. THE VENDOR NETWORK DESIGNERS SHALL ATTEND A DESIGN WORKSHOP IN TALLAHASSEE AFTER A HIGH-LEVEL DESIGN HAS BEEN ACCEPTED. THE DESIGN WORKSHOP WILL BE AN INTERACTIVE SESSION TO FINALIZE AN APPROVED DESIGN OF THE MPLS CORE INCLUDING ALL SERVICES, IP ADDRESSES, AND OTHER DESIGN PARAMETERS. THE VENDOR SHALL STAGE ALL EQUIPMENT SUPPLIED BY THIS PROJECT IN A VENDOR SUPPLIED WAREHOUSE. THE STAGING OF THE EQUIPMENT SHALL BE FULLY INTERCONNECTED AND CONFIGURED AS IT WILL BE IN THE FIELD. THE VENDOR IS RESPONSIBLE R DESIGNING A STAGING ACCEPTANCE PLAN TO BE APPROVED BY THE FDOT. THE FDOT WILL WITNESS SYSTEM STAGING TESTING. THE STAGING ACCEPTANCE PLAN SHALL BE COMPLETELY MET BERE EQUIPMENT MAY BE DEPLOYED TO THE FIELD. THIS PROJECT S NETWORK ARCHITECTURE CENTERS AROUND A 14-NODE MPLS TRANSPORT CORE CONSISTING OF NOKIA 7705 SAR-18S LOCATED AT MICROWAVE BANDWIDTH AGGREGATION HUB SITES. INITIALLY, NOKIA 7705 SAR18 ROUTERS WILL BE INSTALLED AND PLACED INTO OPERATION ACROSS INTER-NODAL DS-1 AGGREGATION LINKS, OPERATING IN PARALLEL WITH THE EXISTING NORTEL PASSPORT NETWORK SWITCHING EQUIPMENT. THE FDOT S ITS CENTER-TO-CENTER (C2C) DATA SERVICES WILL THEN BE MIGRATED FROM THE NORTEL PASSPORT NETWORK EQUIPMENT TO THE 7705 SAR18 S TRANSPORT SERVICES. THE PROJECT WILL NEXT INSTALL 7705 SAR18 ROUTERS AT ALL MICROWAVE REPEATER SITES THROUGHOUT THE STATE, THEN MIGRATE NETWORK MANAGEMENT AND FIELD DATA NETWORK SERVICES FROM THE ASN ROUTERS, BPS2000, AND ETHERNET HUBS, TO THE 7705 SAR18 S TRANSPORT SERVICES. THE NORTEL PASSPORT 15000, WIDEBANK28, ASN ROUTER, BPS2000, AND ETHERNET HUB EQUIPMENT WILL BE DECOMMISSIONED AFTER SUCCESSFUL MIGRATION OF ALL FDOT DATA SERVICES TO THE 7705 SAR18 TRANSPORT NETWORK. THE DEPLOYED SYSTEM SHALL FEATURE COMPLETE INTEGRATION R OPERATIONS, ADMINISTRATION, MAINTENANCE, AND PROVISIONING (OAM&P) WITH NOKIA SERVICE AGGREGATION ROUTERS, NOKIA MPR-9500 MICROWAVE RADIOS, NOKIA OPTICAL TRANSPORT NETWORK EQUIPMENT, AND WITH THE GLOBAL NOKIA 5620 NETWORK FUNCTIONS MANAGER R PACKET, TO SUPPORT MICROWAVE RADIO-AWARE DYNAMIC TRAFFIC ENGINEERING. THE VENDOR SHALL UNINSTALL, REMOVE, AND PROPERLY DISPOSE OF ALL NORTEL PASSPORT 15000, WIDEBANK28, ASN ROUTER, BPS2000, AND BAYSTACK HUB EQUIPMENT, IN ACCORDANCE WITH FDOT PROCEDURES, PRIOR TO SYSTEM ACCEPTANCE. THE VENDOR SHALL UNINSTALL NETGUARDIAN RTUS, MULTITECH VOIP ROUTERS, TELCO SYSTEMS ACCESS60 CHANNEL BANK AND ACCESS60 REDUNDANCY CABLE HARNESSES, AND DELIVER THE EQUIPMENT TO THE FDOT. GENERAL NOTES: 1. THE VENDOR SHALL BE RESPONSIBLE R VERIFYING ALL CONDITIONS AND MEASUREMENTS RELATING TO THE WORK IN THE FIELD PRIOR TO PROCEEDING WITH INSTALLATION, REMOVAL, AND DISPOSAL ACTIVITIES. THE VENDOR SHALL COORDINATE ANY MODIFICATIONS REQUIRED WITH FDOT. 2. THE VENDOR IS RESPONSIBLE R ALL EQUIPMENT, MATERIALS, AND SERVICES REQUIRED TO COMPLETE THIS PROJECT. THE VENDOR IS RESPONSIBLE R VERIFYING THE COMPLETENESS OF MATERIALS REQUIRED AND SUITABILITY OF DEVICES TO MEET THESE PLANS. THE VENDOR SHALL PROVIDE AND INSTALL, WITHOUT CLAIM, ANY ADDITIONAL EQUIPMENT AND SERVICES REQUIRED R OPERATION PER THESE PLANS. 3. THE VENDOR SHALL BE RESPONSIBLE R DETERMINING LOCAL FACILITIES R DELIVERING, STORING, AND LEGALLY DISPOSING OF POST-INSTALLATION MATERIALS. 4. THE VENDOR SHALL PROTECT AND PRESERVE ALL EXISTING UTILITIES, EXCLUDING THOSE REQUIRING UPGRADES OR RELOCATION IN THESE PLANS, LOCATED WITHIN THE INSTALLATION LIMITS OF THE PROJECT. 5. THE VENDOR IS RESPONSIBLE R OBTAINING ANY PERMITS (DEP, SOUTH FLORIDA WATER MANAGEMENT DISTRICT, ETC.) AND MEETING BUILDING OFFICIAL REQUIREMENTS, INCLUDING ASSOCIATED FEES. THE VENDOR IS RESPONSIBLE R CONTACTING APPLICABLE BUILDING OFFICIALS R PERMIT APPLICATIONS AND SUBMITTING TO THE FDOT R SIGNATURE. 6. THE VENDOR SHALL SUBMIT ALL DETAILED DESIGN PLANS R FDOT REVIEW AND APPROVAL PER THESE PLANS AND SPECIFICATIONS. THE VENDOR SHALL NOT BEGIN INSTALLATION WORK UNTIL ALL DESIGN SUBMITTALS ARE APPROVED IN WRITING BY THE FDOT PROJECT MANAGER. 7. THE VENDOR SHALL SUBMIT AN INSTALLATION SCHEDULE TO FDOT R REVIEW AND APPROVAL. 8. THE VENDOR MUST COORDINATE ALL SITE WORK WITH FDOT. THE CONTACT PERSON IS RANDY PIERCE, ALL TOWER AND ANTENNA INSTALLATION WORK SHALL BE DONE BY TOWER CLIMBERS CERTIFIED BY COMTRAIN, OR APPROVED EQUIVALENT. 10. THE VENDOR SHALL COORDINATE EACH ELEMENT ON THE SCHEDULE WITH OTHER INSTALLATION ACTIVITIES AND SHOW EACH ACTIVITY IN PROPER SEQUENCE. FLORIDA GENERAL NOTES (CONT D): 11. THE VENDOR SHALL FIELD LOCATE ALL BURIED GROUNDING, CONDUITS, STRUCTURES, AND UTILITIES IN AND AROUND THE WORK AREA PRIOR TO COMMENCING ANY EXCAVATIONS. ALL DIGGING AND EXCAVATING INSIDE AND AROUND THE SITE COMPOUND SHALL BE PERRMED IN A MANNER CONSISTENT WITH GOOD ENGINEERING PRACTICES. THE USE OF HEAVY EXCAVATING MACHINERY IS NOT PERMITTED. 12. THE VENDOR SHALL RESTRICT PERSONNEL, THE USE OF EQUIPMENT, AND THE STORAGE OF MATERIALS TO AREAS WITHIN THE LIMITS OF INSTALLATION. ANY OFF-SITE STORAGE AREA IS THE RESPONSIBILITY OF THE VENDOR. 13. THE VENDOR SHALL PROVIDE SECURITY R HIS/HER EQUIPMENT AND SHALL CONDUCT HIS/HER OPERATIONS TO AVOID INTERFERENCE WITH FDOT'S NORMAL OPERATIONS. 14. ALL EXISTING DRIVEWAYS, EASEMENTS, AND GROUNDS SHALL BE PROTECTED OR RESTORED TO INITIAL CONDITION IF DAMAGED OR DISTURBED BECAUSE OF INSTALLATION WORK. 15. THE VENDOR SHALL PROVIDE AND MAINTAIN IN A NEAT AND SANITARY CONDITION SUCH ACCOMMODATIONS R THE USE OF HIS/HER EMPLOYEES AS MAY BE NECESSARY TO COMPLY WITH REGULATIONS OF THE OR THE DEPARTMENT OF HEALTH. NO NUISANCE WILL BE PERMITTED. 16. THE VENDOR SHALL BE RESPONSIBLE R REMOVING AND LEGALLY DISPOSING OF THE TRASH GENERATED FROM THE INSTALLATION, INCLUDING LUNCH BAGS AND DRINKS, DAILY. THE VENDOR SHALL NOT ALLOW TRASH TO BLOW AROUND OR AWAY FROM ANY CONSTRUCTION SITE. 17. ALL EQUIPMENT AND SERVICES FURNISHED BY THE VENDOR AS PART OF THIS PROJECT SHALL BE WARRANTED TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP. IN THE EVENT ANY SUCH DEFECTS IN EQUIPMENT OR SERVICES BECOME EVIDENT WITHIN THE WARRANTY PERIOD, THE VENDOR SHALL CORRECT THE DEFECT BY REPAIRING OR REPLACING THE DEFECTIVE COMPONENT OR EQUIPMENT AT NO COST TO FDOT DURING THE WARRANTY PERIOD. THE WARRANTY PERIOD SHALL BE A MINIMUM OF 12 MONTHS FROM DATE OF FINAL ACCEPTANCE. CLAIMS UNDER ANY OF THE WARRANTIES HEREIN ARE VALID IF MADE WITHIN 30 DAYS AFTER TERMINATION OF THE WARRANTY PERIOD. 18. THE VENDOR SHALL COLLECT PRODUCT DATA INTO A SINGLE SUBMITTAL R EACH ELEMENT OF INSTALLATION OR SYSTEM. PRODUCT DATA SHALL INCLUDE PRINTED INRMATION SUCH AS MANUFACTURER'S INSTALLATION INSTRUCTIONS AND PERRMANCE SPECIFICATIONS. 19. THE VENDOR SHALL SUBMIT (2) SETS OF AS-BUILT DRAWINGS DEPICTING THE LOCATION OF THE COMPONENTS OF THE COMMUNICATIONS FACILITIES WITH RESPECT TO LOCAL FEATURES AND BENCHMARKS. AS-BUILT DRAWINGS DEPICTING ANY FIELD CHANGES TO THE FACILITIES SHALL ALSO BE SUBMITTED. AS-BUILT DOCUMENTATION SHALL BE SUBMITTED IN ELECTRONIC RMAT, AS WELL AS PRINTED. ALL ITS FACILITY MANAGEMENT ATTRIBUTE RMS SHALL BE COMPLETED IN ACCORDANCE WITH THE TECHNICAL SPECIFICATIONS. APPLICABLE PUBLICATIONS AND STANDARDS: 1. ANSI/TIA-222-G, STRUCTURAL STANDARD R ANTENNA SUPPORTING STRUCTURES AND ANTENNAS, STRUCTURE CLASSIFICATION-III. 2. APPLICABLE MANUFACTURER S INSTRUCTIONS AND STANDARD PRACTICES. 3. APPLICABLE OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (O.S.H.A.) PRACTICES. 4. ASTM A123: STANDARD SPECIFICATION R: ZINC (HOT GALVANIZED) COATINGS ON PRODUCTS FABRICATED FROM ROLLED, PRESSED, AND RGED STEEL SHAPES, PLATES, BARS, AND STRIP. 5. ASTM A153: STANDARD SPECIFICATION R: ZINC COATING (HOT-DIP) ON IRON AND STEEL HARDWARE. 6. EIA-81: MEASURING GROUND RESISTANCE AND POTENTIAL GRADIENTS IN THE EARTH. 7. FLORIDA BUILDING CODE, CURRENT EDITION. 8. CURRENT FDOT STANDARD SPECIFICATIONS R ROAD AND BRIDGE DESIGN. 9. CURRENT FDOT DESIGN STANDARDS. 10. FEDERAL AVIATION ADMINISTRATION REGULATIONS. 11. FEDERAL COMMUNICATIONS COMMISSION REGULATIONS. 12. IEEE 837: STANDARD R QUALIFYING PERMANENT CONNECTIONS USED IN SUBSTATION GROUNDING. 13. NATIONAL ELECTRICAL CODE (NEC) (NFPA 70), CURRENT EDITION. 14. NEC ARTICLE 250: GROUNDING AND BONDING. 15. NIST: NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY. 16. UL 467: STANDARDS R GROUNDING AND BONDING EQUIPMENT. 17. NATIONAL FIRE PROTECTION ASSOCIATION (NFPA 780) GENERAL NOTES \\dotscoteo1\traffic_ops_data\public\tsmo\telcom\\ Technology Replacement Plan\Phase 2 Contract Plans\Contract Plans\1-Notes\A-Notes vsd Attachment 1 2 A-2

3 Sumter Milton Pensacola Escambia Holt Mossy Head Santa Rosa Crestview DeFuniak Okaloosa STATEWIDE ITS Communications NETWORK (sicn) map Legend Interstate District 1 District 2 District 3 District 4 District 5 District 6 District 7 Repeater Site Sneads Weigh Station Caryville Aspalaga Quincy Walton Chipley Holmes Washington Bay Marianna Tallahassee Jackson Calhoun Liberty Gulf Franklin Gadsden Leon Wakulla Monticello Jefferson Madison Madison Taylor US 41 Greenville SR 222 CR 318 Ocala Lafayette Dixie Wildwood Wildwood Turnpike Hamilton Columbia Baker Suwannee Clermont Gilchrist Saint Catherine Orlando West Interchange Jessamine Temple Terrace Tampa DOT/FHP SR 6 Falmouth Tampa Maintenance Ruskin Pinellas Fruitville Jacaranda SR 136 Levy Orlando South Interchange Canoe Creek Service Plaza Union Citrus Hernando Pasco Alachua Putnam Hillsborough Manatee Sarasota Port Charlotte Lake City Bayshore Bradford Lee Estero Baldwin Sanderson Yulee Nassau Clay Marion Naples Hardee DeSoto Lake Charlotte Miles City Duval St. Johns Polk Collier County Rest Area Miccosukee Andytown Flagler Volusia Seminole Orange Osceola Highlands Glades Hendry Collier Brevard Okeechobee Monroe Jacksonville Saint Johns Rest Area SR 16 Gopher Ridge US 1 Weigh Station Ormond Beach Deland Wilson Road Indian River Port Orange Sanlando Springs St. Lucie Martin Palm Beach Broward Dade Edgewater Mims Cocoa FHP Kenansville Interchange June Park Yeehaw Junction Brevard County Line Site X 90th Avenue Indrio Road Fort Pierce Interchange Fort Pierce Maintenance Stuart Interchange Stuart Maintenance Jupiter Interchange West Palm Beach Interchange Lake Worth FHP Delray Beach Interchange Pompano Beach Interchange McArthur Interchange McArthur Okeechobee Interchange District 6 RTMC Coral Reef Interchange FLORIDA Sicn map \\dotscoteo1\traffic_ops_data\public\tsmo\telcom\\ Technology Replacement Plan\Phase 2 Contract Plans\Contract Plans\1-Notes\A-Notes vsd A-3 Attachment 1 3

4 INSTALLATION DESIGN PLAN: 1. THE VENDOR SHALL SUBMIT DETAILED DESIGN PLANS AND A DETAILED COMPREHENSIVE MATERIALS LIST R FDOT REVIEW AND APPROVAL PRIOR TO INSTALLATION WORK. 2. THE VENDOR SHALL SUBMIT A NETWORK LOW-LEVEL DESIGN AND EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST, WHICH DEFINES THE NETWORK MPLS TRANSPORT SERVICES AND THE SERVICE ACCESS ROUTER INTERFACES. 3. THE NETWORK DESIGN SHALL BE REALIZED WITH NOKIA 7705 SAR-18 SERVICE AGGREGATION ROUTER, NOKIA 7750 SR-A8 SERVICE ROUTER, AND NOKIA MPR-9500 MICROWAVE PACKET RADIO TECHNOLOGY, TO PROVIDE COMPATIBILITY WITH THE FDOT S STATEWIDE ITS COMMUNICATIONS NETWORK MICROWAVE TDM DS-1 TRANSPORT BACKBONE, THE NOKIA NETWORK FUNCTIONS MANAGER R PACKET, AND NOKIA S MICROWAVE RADIO AWARE TRAFFIC ENGINEERING CAPABILITY. GENERAL INSTALLATION NOTES: 1. THE VENDOR SHALL SUBMIT A DETAILED OVERALL PROJECT PLAN TO BE APPROVED BY THE FDOT. THE PLANS SHALL INCLUDE AN EQUIPMENT INSTALLATION AND CUT-OVER SEQUENCING PLAN. THE PLAN SHALL INCLUDE A SCHEDULE OF EVENTS DETAILING EACH PHASE OF INSTALLATION, INCLUDING A PROJECTED TIMELINE. 2. THE VENDOR SHALL PROVIDE AND INSTALL ALL ETHERNET SWITCHING EQUIPMENT, ANCILLARY EQUIPMENT, SURGE PROTECTION, GROUNDING, RACKS, ANTENNAS, AND ASSOCIATED MOUNTING HARDWARE IN ACCORDANCE WITH THESE PLANS. ALL EQUIPMENT AND COMPONENT PARTS FURNISHED SHALL BE NEW, MEET OR EXCEED THE MINIMUM REQUIREMENTS STATED HEREIN, AND PERRM TO MANUFACTURER S SPECIFICATIONS. NO PART OR ATTACHMENT SHALL BE SUBSTITUTED OR APPLIED CONTRARY TO THE MANUFACTURER'S RECOMMENDATIONS AND STANDARD PRACTICES. 3. THE VENDOR SHALL FURNISH AND INSTALL ALL GPS ANTENNAS, COAXIAL CABLES, POWER CABLES, DATA CABLES, AND RESPECTIVE CONNECTORS, HARDWARE, ENTRY PORT BOOTS, SEALS, AND CONDUITS. 4. THE TRANSMISSION LINES SHALL BE INSTALLED IN SUCH A MANNER THAT DOES NOT VIOLATE THE MANUFACTURER S MAXIMUM TWIST, MINIMUM E-BEND RADIUS, AND MINIMUM H-BEND RADIUS SPECIFICATIONS. ANY ELLIPTICAL WAVEGUIDES OR OTHER TRANSMISSION LINES DAMAGED BY THE VENDOR SHALL BE REPLACED WITH NEW FULL-LENGTH WAVEGUIDES OR OTHER TRANSMISSION LINES, WITHOUT CLAIM, AND AT THE VENDOR S COST. 5. THE VENDOR IS RESPONSIBLE R VERIFYING CORRECT SIZE, GENDER, AND SUITABILITY OF ALL CABLE CONNECTORS AND SURGE PROTECTIVE DEVICES. HUB SITE INSTALLATION NOTES: 1. THE VENDOR SHALL PROVIDE AND INSTALL THE GPS ANTENNA SYSTEMS, ELECTRONIC EQUIPMENT, RACKS, SURGE PROTECTIVE DEVICES (SPD), AND LIGHTNING PROTECTION AND GROUNDING SYSTEMS PER THESE PLANS, IN ACCORDANCE WITH SHEETS H-1 THROUGH H ALL COAXIAL TRANSMISSION LINES SHALL BE EQUIPPED WITH SPDS PER THESE SPECIFICATIONS. ALL SPDS SHALL BE CONNECTED DIRECTLY TO THE BULKHEAD UPON ENTERING THE COMMUNICATIONS SHELTER. 3. THE VENDOR SHALL PROVIDE AND INSTALL -48 VDC A/B FUSE PANEL, NOKIA 7705 SAR-18 SERVICE AGGREGATION ROUTER, DSX PANEL, DS-1 SPDS, AND APPROPRIATE DIN MOUNTED ETHERNET SPDS INTO THE DESIGNATED RACK(S) SHOWN ON SITE-SPECIFIC BLDG INSTALLATION PLANS. THE VENDOR SHALL PROVIDE NEW RACKS AS SPECIFIED. HOWEVER, DUE TO SPACE CONSTRAINTS, SOME SITE INSTALLATIONS REQUIRE EQUIPMENT INTEGRATION INTO EXISTING RACKS. RACK SPACE ALLOCATIONS AND EXISTING RACKS PROVIDED BY OTHERS ARE SHOWN ON THE SITE-SPECIFIC BLDG INSTALLATION PLANS. 4. THE NEW EQUIPMENT RACKS SHALL BE EIA 19-INCH BY 7-FEET OPEN ALUMINUM RELAY EQUIPMENT RACKS BUD INDUSTRIES, MODEL ARR-1272-NATURAL, OR APPROVED EQUIVALENT. THE RACKS SHALL BE MOUNTED TO THE FLOOR USING RELAY RACK ANCHOR KITS B- LINE SYSTEMS MODEL SB-588-A, APPROVED EQUIVALENT. THE RELAY RACKS SHALL BE INSTALLED IN ACCORDANCE WITH THE CONTRACT PLANS. 5. THE VENDOR SHALL PROVIDE AND INSTALL INTERCONNECTION WIRING AND JUMPERS R POWER, ETHERNET, FIBER OPTIC, COAXIAL, AND DS-1, IN ACCORDANCE WITH THESE CONTRACT PLANS. 6. THE VENDOR SHALL CONFIGURE THE NOKIA 7705 SAR-18 EQUIPMENT IN ACCORDANCE WITH THE VENDOR S LOW-LEVEL NETWORK DESIGN TO ACHIEVE TRANSPORT AND INTERNETWORKING OPERATION OF THE DATA SERVICES AND ATTACHED DEVICES AS SPECIFIED ON THE EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 7. THE VENDOR SHALL CUT-OVER THE INSTALLED SYSTEM IN ACCORDANCE WITH THE APPROVED EQUIPMENT INSTALLATION AND CUT- OVER SEQUENCING PLAN, AND TEST AND VERIFY ALL NETWORK SERVICES AND EQUIPMENT OPERATIONS. REPEATER AND SPUR SITE INSTALLATION NOTES: 1. THE VENDOR SHALL PROVIDE AND INSTALL THE ELECTRONIC EQUIPMENT, RACKS, SPDS, AND LIGHTNING PROTECTION AND GROUNDING SYSTEMS PER THESE PLANS, IN ACCORDANCE WITH SHEETS S-1 THROUGH S-6 R SPUR SITES, AND R-1 THROUGH R-24 R REPEATER SITES. 2. THE VENDOR SHALL PROVIDE AND INSTALL -48 VDC A/B FUSE PANEL, NOKIA 7705 SAR-18 SERVICE AGGREGATION ROUTER, DSX PANEL, DS- 1 SPDS, AND APPROPRIATE DIN MOUNTED ETHERNET SPDS INTO THE DESIGNATED RACK(S) SHOWN ON THE SITE-SPECIFIC BLDG INSTALLATION PLANS. THE VENDOR SHALL PROVIDE NEW RACKS AS SPECIFIED. HOWEVER, DUE TO SPACE CONSTRAINTS, SOME SITE INSTALLATIONS REQUIRE EQUIPMENT INTEGRATION INTO EXISTING RACKS. RACK SPACE ALLOCATIONS AND EXISTING RACKS PROVIDED BY OTHERS ARE SHOWN ON THE SITE-SPECIFIC BLDG INSTALLATION PLANS. 3. THE NEW EQUIPMENT RACKS SHALL BE EIA 19-INCH BY 7-FEET OPEN ALUMINUM RELAY EQUIPMENT RACKS BUD INDUSTRIES, MODEL ARR NATURAL, OR APPROVED EQUIVALENT. THE RACKS SHALL BE MOUNTED TO THE FLOOR USING RELAY RACK ANCHOR KITS B-LINE SYSTEMS MODEL SB-588-A, APPROVED EQUIVALENT. THE RELAY RACKS SHALL BE INSTALLED IN ACCORDANCE WITH THE CONTRACT PLANS. 4. THE VENDOR SHALL PROVIDE AND INSTALL INTERCONNECTION WIRING AND JUMPERS R POWER, ETHERNET, FIBER OPTIC, COAXIAL, AND DS-1, IN ACCORDANCE WITH THESE CONTRACT PLANS. 5. THE VENDOR SHALL CONFIGURE THE NOKIA 7705 SAR-18 EQUIPMENT IN ACCORDANCE WITH THE VENDOR S LOW-LEVEL NETWORK DESIGN TO ACHIEVE TRANSPORT AND INTERNETWORKING OPERATION OF THE DATA SERVICES AND ATTACHED DEVICES AS SPECIFIED ON THE EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 6. THE VENDOR SHALL CUT-OVER THE INSTALLED SYSTEM IN ACCORDANCE WITH THE APPROVED EQUIPMENT INSTALLATION AND CUT-OVER SEQUENCING PLAN, AND TEST AND VERIFY ALL NETWORK SERVICES AND EQUIPMENT OPERATIONS. TURNPIKE SITE INSTALLATION NOTES: 1. THE VENDOR SHALL PROVIDE AND INSTALL THE GPS ANTENNA SYSTEMS, ELECTRONIC EQUIPMENT, RACKS, SPDS, AND LIGHTNING PROTECTION AND GROUNDING SYSTEMS PER THESE PLANS, IN ACCORDANCE WITH SHEETS T-1 THROUGH T ALL COAXIAL TRANSMISSION LINES SHALL BE EQUIPPED WITH SPDS PER THESE SPECIFICATIONS. ALL SPDS SHALL BE CONNECTED DIRECTLY TO THE BULKHEAD UPON ENTERING THE COMMUNICATIONS SHELTER. 3. THE VENDOR SHALL PROVIDE AND INSTALL -48 VDC A/B FUSE PANEL, NOKIA 7705 SAR-18 SERVICE AGGREGATION ROUTER, DSX PANEL, DS- 1 SPDS, APPROPRIATE DIN MOUNTED ETHERNET SPDS, AND DPS NETGUARDIAN RTU, DPS SPDS, INTO THE DESIGNATED RACK(S) SHOWN ON THE SITE-SPECIFIC BLDG INSTALLATION PLANS. THE VENDOR SHALL PROVIDE NEW RACKS AS SPECIFIED. HOWEVER, DUE TO SPACE CONSTRAINTS, SOME SITE INSTALLATIONS REQUIRE EQUIPMENT INTEGRATION INTO EXISTING RACKS. RACK SPACE ALLOCATIONS AND EXISTING RACKS PROVIDED BY OTHERS ARE SHOWN ON THE SITE-SPECIFIC BLDG INSTALLATION PLANS. 4. THE NEW EQUIPMENT RACKS SHALL BE EIA 19-INCH BY 7-FEET OPEN ALUMINUM RELAY EQUIPMENT RACKS BUD INDUSTRIES, MODEL ARR NATURAL, OR APPROVED EQUIVALENT. THE RACKS SHALL BE MOUNTED TO THE FLOOR USING RELAY RACK ANCHOR KITS B-LINE SYSTEMS MODEL SB-588-A, APPROVED EQUIVALENT. THE RELAY RACKS SHALL BE INSTALLED IN ACCORDANCE WITH THE CONTRACT PLANS. 5. THE VENDOR SHALL PROVIDE AND INSTALL THE WALL MOUNTED MULTITECH VOIP ROUTER, RED TELEPHONE, PUNCH BLOCKS, INTERCONNECT WIRING, AND LIGHTNING PROTECTION GROUND BONDING ON THE SHELTER TELCO BACKBOARD AS SHOWN ON SHEET E THE VENDOR SHALL CONNECT AND CONFIGURE THE EXISTING TELCO SYSTEMS ACCESS60 CHANNEL TO PROVIDE SNMP NETWORK MANAGEMENT SUPPORT AT EACH TURNPIKE SITE. INSTALL ETHERNET CONNECTION, WITH SPD, TO THE 7705 SAR18 AS SPECIFIED IN THE EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 7. THE VENDOR SHALL PROVIDE AND INSTALL INTERCONNECTION WIRING AND JUMPERS R POWER, ETHERNET, FIBER OPTIC, COAXIAL, AND DS-1, IN ACCORDANCE WITH THESE CONTRACT PLANS. 8. THE VENDOR SHALL CONFIGURE THE NOKIA 7705 SAR-18 EQUIPMENT IN ACCORDANCE WITH THE VENDOR S LOW-LEVEL NETWORK DESIGN TO ACHIEVE TRANSPORT AND INTERNETWORKING OPERATION OF THE DATA SERVICES AND ATTACHED DEVICES AS SPECIFIED ON THE EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 9. THE VENDOR SHALL CUT-OVER THE INSTALLED SYSTEM IN ACCORDANCE WITH THE APPROVED EQUIPMENT INSTALLATION AND CUT-OVER SEQUENCING PLAN, AND TEST AND VERIFY ALL NETWORK SERVICES AND EQUIPMENT OPERATIONS. DATE 8/7/18 REV. 1 ADD INSTALLATION OF SAFETY CLIMB SYSTEM SANLANDO SPRINGS NOTES 1 AND 2 DATE REV. FLORIDA Installation Notes \\dotscoteo1\traffic_ops_data\public\tsmo\telcom\\ Technology Replacement Plan\Phase 2 Contract Plans\Contract Plans\1-Notes\A-Notes vsd A-4 Attachment 1 4

5 EQUIPMENT INSTALLATION AND CUT-OVER SEQUENCING PLAN: 1. GENERAL 1.1 THE VENDOR SHALL SUBMIT A DETAILED EQUIPMENT INSTALLATION AND CUT-OVER SEQUENCING PLAN R APPROVAL BY FDOT. THE PLAN SHALL INCLUDE A DETAILED ORDER OF INSTALLATIONS, SERVICES CUT-OVER, TESTING, AND REMOVALS. 1.2 THE FDOT S NETWORK SYSTEMS ARE IN SERVICE AND CARRYING CRITICAL COMMUNICATIONS TRAFFIC. ANY DOWNTIME OF THE EXISTING SYSTEM MUST BE COORDINATED WITH THE FDOT PRIOR TO THE DOWNTIME OCCURRENCE. ALL WORK CLASSIFIED AS CAUSING LESS THAN FIVE MINUTES OF DOWNTIME REQUIRES A MINIMUM OF TWO DAYS PRIOR NOTICE. ALL WORK CLASSIFIED AS CAUSING FIVE MINUTES OR MORE DOWNTIME REQUIRES A MINIMUM OF TEN DAYS PRIOR NOTICE AND MUST BE COORDINATED WITH THE FDOT PRIOR TO OCCURRENCE. 1.3 THE VENDOR SHALL CONFIGURE, STAGE, AND TEST THE EQUIPMENT AND SERVICES IN A SYSTEM STAGING FACILITY BERE DEPLOYING TO THE FIELD. THE FDOT SHALL WITNESS AND ACCEPT THE TEST RESULTS BERE THE VENDOR INSTALLS THE EQUIPMENT IN THE FIELD AND CUTS-OVER SERVICES. 2. WILSON ROAD NFM-P, 7750 SERVICE ROUTER 2.1 RELOCATE NETWORK FUNCTIONS MANAGER R PACKET (NFM-P) SERVER FROM DISTRICT 6 RTMC AND INSTALL AND CONFIGURE INTO THE EXISTING WILSON RD 7705 SAR-18 RACK, SEE SHEET H-1 UPGRADE THE NFM-P SYSTEM HARDWARE AND SOFTWARE TO SUPPORT THE NOKIA EQUIPMENT, SERVICES, AND PROTOCOLS IMPLEMENTED BY THIS PROJECT. 2.2 INSTALL AND CONFIGURE THE 7750 SERVICE ROUTER INTO THE WILSON RD 7705 SAR-18 RACK, SEE SHEET H EXECUTE RECONFIGURATION OF THE 7705 TO ACTIVATE THE INTERIM EQUIPMENT CONFIGURATION PARAMETERS, SHEET A TEST AND VERIFY NFM-P OPERATIONS AMONG THE JACKSONVILLE, WILSON RD, SANLANDO SPRINGS, AND KEYS MICROWAVE NETWORK NODES. 3. HUB SITES MPLS CORE, MICROWAVE DS-1 TRANSMISSION LINKS 3.1 INSTALL 7705 SAR18 AT THE LLOWING HUB SITES: 1. PENSACOLA 2. CHIPLEY 3. TALLAHASSEE 4. LAKE CITY 5. WILDWOOD 6. TAMPA MAINTENANCE 7. JACARANDA 8. NAPLES 9. MCARTHUR 10. STUART MAINTENANCE 11. JUNE PARK 12. PORT ORANGE 3.2 ACTIVATE T2 #2 DROP/INSERT ON ALL DVM MUX A2/B2 M12 CARDS AT EACH REPEATER SITE LOCATED BETWEEN HUB SITES. 3.3 CUT-OVER DS-1 #1, AND #5-18 FROM EACH DVM6-45 MUX TO THE HUB SITE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACES, IN ACCORDANCE WITH INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. SITES DESIGNATED REQUIRE SPECIAL DS-1 CUT-OVER, IN ACCORDANCE WITH THE INTERIM EQUIPMENT CONFIGURATION PARAMETERS LIST: 1. PENSACOLA 2. CHIPLEY 3. TALLAHASSEE 4. LAKE CITY 5. WILDWOOD TAMPA MAINTENANCE CUT-OVER DS-1 #1, AND #5-18 FROM THE TEMPLE TERRACE COORDINATE SITE DVM6-45 TO THE EXISTING 7705 SAR18. CUT-OVER DS-1 #1, AND #5-18 FROM THE RUSKIN COORDINATE SITE DVM6-45 TO THE EXISTING 7705 SAR18. CUT-OVER DS-1 #1, #2, #5, #7, AND #8 FROM THE TAMPA FHP COORDINATE SPUR DVM10-8T TO THE EXISTING 7705 SAR JACARANDA 8. NAPLES 9. MCARTHUR 10. STUART MAINTENANCE 11. JUNE PARK 12. PORT ORANGE JACKSONVILLE CUT-OVER DS-1 #1, AND #5-18 FROM THE BALDWIN COORDINATE SITE DVM6-45 TO THE 7705 SAR18. CUT-OVER DS-1 #2, AND #5-28 FROM THE YULEE COORDINATE SPUR DVM6-45 TO THE 7705 SAR18. SOFTWARE RECONFIGURATION OF THE DS-1 BUNDLE IS REQUIRED. DS-1 #1, AND #5-18 FROM THE ST. JOHNS REST AREA COORDINATE SITE DVM6-45 ARE PRE-WIRED TO THE 7705 SAR-18, NO DS-1 CUT-OVER IS NEEDED. SANLANDO SPRINGS SOFTWARE RECONFIGURATION OF THE DS-1 BUNDLE IS REQUIRED.DS-1 #1, AND #5-18 FROM THE DELAND COORDINATE SITE DVM6-45 ARE PRE-WIRED TO THE EXISTING 7705 SAR18, NO DS-1 CUT-OVER NEEDED. 3. HUB SITES MPLS CORE, MICROWAVE DS-1 TRANSMISSION LINKS (CONT D) 3.4 COMMISSION THE INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS AT ALL HUB SITES AND TEST HUB SITES MPLS CORE NETWORK OPERATION 3.5 PERRM INTERIM SITE EQUIPMENT INTERFACE PORT CUT-OVERS FROM AVAYA 8800/8600, BPS2000, ASN ROUTER, AND BAYSTACK HUB TO 7705 SAR18 AT EACH HUB SITE. SEE INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 3.6 CUT-OVER ALL ITS WAN SERVICES FROM THE PASSPORT TRANSPORT TO THE 7705 SAR18 HUB SITES MPLS CORE NOW TRANSPORTED ON DS-1 BUNDLE #9-18. (3-DAY PERRMANCE TEST) 4. SPUR SITES MPLS SEGMENTS, MICROWAVE DS-1 TRANSMISSION LINKS 4.1 INSTALL 7705 SAR18 AT EACH SPUR SITE: 1. SR6 2. YULEE 3. TAMPA DOT/FHP 4.2 SR6 SPUR SITE - CUT-OVER DS-1 #5-8 FROM THE DVM6-45 MUX TO THE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACE. PERRM INTERIM SITE EQUIPMENT INTERFACE PORT CUT-OVERS FROM BPS2000, ASN ROUTER, AND BAYSTACK HUB TO 7705 SAR18 AT THE SPUR SITE. SEE INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 4.3 YULEE SPUR SITE - CUT-OVER DS-1 #2 AND #5-28 FROM THE DVM6-45 MUX TO THE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACE. PERRM INTERIM SITE EQUIPMENT INTERFACE PORT CUT-OVERS FROM BPS2000, ASN ROUTER, AND BAYSTACK HUB TO 7705 SAR18 AT THE SPUR SITE. SEE INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 4.4 TAMPA DOT/FHP SPUR SITE - CUT-OVER DS-1 #1, #2, #5, #7, AND #8 FROM THE DVM10-8T MUX TO THE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACE. PERRM INTERIM SITE EQUIPMENT INTERFACE PORT CUT-OVERS FROM BPS2000, ASN ROUTER, AND BAYSTACK HUB TO 7705 SAR18 AT THE SPUR SITE. SEE INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 4.5 COMMISSION THE INTERIM EQUIPMENT CONFIGURATION PARAMETERS AT THE SPUR SITES AND TEST SPUR SITES MPLS CORE NETWORK OPERATION (3-DAY PERRMANCE TEST). 5. REPEATER SITES MPLS SEGMENTS, MICROWAVE DS-1 TRANSMISSION LINKS 5.1 INSTALL 7705 SAR18 AT EACH REPEATER SITE ALONG THE LLOWING HUB-TO-HUB REPEATER SITES SEGMENTS: 1. PENSACOLA_CHIPLEY (6) 2. CHIPLEY_TALLAHASSEE (4) 3. TALLAHASSEE-LAKE CITY (5) 4. LAKE CITY_JACKSONVILLE (2) 5. LAKE CITY_WILDWOOD (4) 6. WILDWOOD_TAMPA MAINTENANCE (3) 7. TAMPA MAINTENANCE_JACARANDA (2) 8. JACARANDA_NAPLES (3) 9. NAPLES_MCARTHUR (4) 10. STUART MAINTENANCE_JUNE PARK (4) 11. JUNE PARK_PORT ORANGE (3) 12. PORT ORANGE_JACKSONVILLE (5) 13. PORT ORANGE_SANLANDO SPRINGS (1) 5.2 CUT-OVER DS-1 #1, AND #5-8 FROM EACH DVM6-45/CONSTELLATION MUX TO THE REPEATER SITE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACES. PERRM INTERIM SITE EQUIPMENT INTERFACE PORT CUT-OVERS FROM BPS2000, ASN ROUTER, AND BAYSTACK HUB TO 7705 SAR18 AT ALL REPEATER SITES STATEWIDE. THE FALMOUTH REPEATER SITE REQUIRES SPECIAL SITE- SPECIFIC DS-1 CUT-OVER. SEE INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 5.3 COMMISSION THE INTERIM EQUIPMENT CONFIGURATION PARAMETERS AT ALL REPEATER SITES AND TEST REPEATER SITES MPLS CORE NETWORK OPERATION (3-DAY PERRMANCE TEST). FLORIDA EQUIPMENT INSTALLATION AND CUT-OVER SEQUENCING Notes \\dotscoteo1\traffic_ops_data\public\tsmo\telcom\\ Technology Replacement Plan\Phase 2 Contract Plans\Contract Plans\1-Notes\A-Notes vsd A-5 Attachment 1 5

6 6.TURNPIKE REPEATER SITES MPLS SEGMENT, MICROWAVE DS-1 TRANSMISSION LINKS 6.1 INSTALL 7705 SAR18, NETGUARDIAN RTU. AND MULTITECH VOIP, AT EACH SITE ALONG THE TURNPIKE WILDWOOD TO CORAL REEF MICROWAVE SYSTEM: 1. WILDWOOD TURNPIKE 2. CLERMONT 3. ORLANDO WEST 4. ORLANDO SOUTH (RTU AND VOIP PREINSTALLED) 5. CANOE CREEK 6. KENANSVILLE 7. YEEHAW JUNCTION 8. SITE X 9. RT PIERCE INTERCHANGE 10. STUART INTERCHANGE 11. JUPITER 12. WEST PALM BEACH 13. DELRAY BEACH 14. POMPANO BEACH 15. MCARTHUR INTERCHANGE 16. OKEECHOBEE 17. CORAL REEF 6.2 AT EACH SITE, CUT-OVER SITE-SPECIFIC DS-1 CHANNELS FROM EACH DVM6-45 MUX TO THE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACES, IN ACCORDANCE WITH THE INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 6.3 INSTALL FIBER OPTIC TRANSMISSION PATHS FROM STUART INTERCHANGE TO STUART MAINTENANCE, AND MCARTHUR TO MCARTHUR INTERCHANGE. 6.4 PERRM INTERIM SITE EQUIPMENT INTERFACE PORT CUT-OVERS FROM BPS2000, ASN ROUTER, AND BAYSTACK HUB TO 7705 SAR18 AT CORAL REEF AND ORLANDO SOUTH. SEE INTERIM EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. 6.5 COMMISSION THE INTERIM EQUIPMENT CONFIGURATION PARAMETERS AT ALL TURNPIKE REPEATER SITES AND TEST REPEATER SITES MPLS CORE NETWORK OPERATION (3-DAY PERRMANCE TEST) 7.FINAL SITE EQUIPMENT INTERFACE PORT CONFIGURATION AND DS-1 LINKS CUT-OVER 7.1 AFTER SUCCESSFUL COMPLETION OF INTERIM SITE EQUIPMENT INTERFACE PORT CUT-OVERS AT ALL HUB, SPUR, AND REPEATER SITES: EXECUTE RECONFIGURATION OF ALL 7705 SAR18 ROUTERS TO ACTIVATE THE FINAL MPLS SERVICES AND SERVICES ACCESS PORTS NETWORK CONFIGURATIONS. SEE FINAL EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. (3- DAY PERRMANCE TEST) 7.2 CUT-OVER REMAINDER DS-1 #3, #4, AND #19-28 FROM EACH DVM6-45 MUX TO THE HUB SITE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACES, IN ACCORDANCE WITH FINAL EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. SITES DESIGNATED REQUIRE SPECIAL DS-1 CUT-OVER, IN ACCORDANCE WITH THE FINAL EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. UNINSTALL AND DISPOSE OF PASSPORT 15000, WIDEBANK28, ASN ROUTER, BPS2000, BAYSTACK HUB. UNINSTALL #2 NETGUARDIAN EQUIPMENT FROM EACH HUB SITE AND DELIVER TO FDOT. HUB SITES: 1. PENSACOLA 2. CHIPLEY 3. TALLAHASSEE 4. LAKE CITY 5. WILDWOOD 6. TAMPA MAINTENANCE 7. JACARANDA JACKSONVILLE SOFTWARE RECONFIGURATION OF THE DS-1 BUNDLE IS REQUIRED. DS-1 #3, #4, AND #19-28 FROM THE ST. JOHNS REST AREA COORDINATE SITE DVM6-45 ARE PRE-WIRED TO THE EXISTING 7705 SAR-18, NO DS-1 CUT-OVER IS NEEDED. SANLANDO SPRINGS SOFTWARE RECONFIGURATION OF THE DS-1 BUNDLE IS REQUIRED. DS-1 #3, #4, AND #19-28 FROM THE DELAND COORDINATE SITE DVM6-45 ARE PRE-WIRED TO THE EXISTING 7705 SAR-18, NO DS-1 CUT-OVER IS NEEDED. NAPLES CUT-OVER REMAINDER DS-1 #3, #4, AND #19-26 FROM THE BAYSHORE COORDINATE SITE DVM6-45 MUX TO THE HUB SITE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACE. CUT-OVER REMAINDER DS-1 #3, #4, AND #19-26 FROM THE MILES CITY COORDINATE SITE CONSTELLATION MUX TO THE HUB MCARTHUR CUT-OVER REMAINDER DS-1 #3, #4, AND #19-26 FROM THE ANDYTOWN COORDINATE SITE CONSTELLATION MUX TO THE HUB STUART MAINTENANCE CUT-OVER REMAINDER DS-1 #3, #4, #19-22, AND #24-28 FROM THE RT PIERCE COORDINATE SITE DVM6-45 MUX TO THE HUB EQUIPMENT INSTALLATION AND CUT-OVER SEQUENCING PLAN (CONT D): 7.FINAL SITE EQUIPMENT INTERFACE PORT CONFIGURATION AND DS-1 LINKS CUT-OVER (CONT D): JUNE PARK CUT-OVER REMAINDER DS-1 #3, #4, #19-22, AND #24-28 FROM THE COCOA FHP COORDINATE SITE DVM6-45 MUX TO THE HUB CUT-OVER REMAINDER DS-1 #3, #4, #19-22, AND #24-28 FROM THE BREVARD LINE COORDINATE SITE DVM6-45 MUX TO THE HUB PORT ORANGE CUT-OVER REMAINDER DS-1 #3, #4, AND #19-28 FROM THE ORMOND BEACH COORDINATE SITE DVM6-45 MUX TO THE HUB CUT-OVER REMAINDER DS-1 #3, #4, AND #19-28 FROM THE DELAND COORDINATE SITE DVM6-45 MUX TO THE HUB SITE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACE. CUT-OVER REMAINDER DS-1 #3, #4, #19-22, AND #24-28 FROM THE EDGEWATER COORDINATE SITE DVM6-45 MUX TO THE HUB 7.5 CUT-OVER REMAINDER DS-1 #3 AND #4, FROM EACH DVM MUX TO EACH SPUR SITE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACES, IN ACCORDANCE WITH FINAL EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. UNINSTALL AND DISPOSE OF ASN ROUTER, BPS2000, AND BAYSTACK HUB EQUIPMENT FROM EACH SPUR SITE: 1. SR6 2. YULEE 3. TAMPA DOT/FHP 7.6 CUT-OVER REMAINDER DS-1 #3 AND #4, FROM EACH DVM6-45 MUX TO EACH REPEATER SITE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACES, IN ACCORDANCE WITH FINAL EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. UNINSTALL AND DISPOSE OF ASN ROUTER, BPS2000, AND BAYSTACK HUB EQUIPMENT FROM EACH REPEATER SITE. 7.7 CUT-OVER REMAINDER SITE-SPECIFIC DS-1S FROM EACH DVM6-45 MUX TO EACH TURNPIKE REPEATER SITE 7705 SAR-18 DS-1 BUNDLE AGGREGATION INTERFACES, IN ACCORDANCE WITH FINAL EQUIPMENT CONFIGURATION INTERFACE PARAMETERS LIST. UNINSTALL AND DISPOSE OF ASN ROUTER, BPS2000, AND BAYSTACK HUB EQUIPMENT FROM ORLANDO SOUTH AND CORAL REEF. 7.8 COMMENCE 20-DAY PERRMANCE TEST PERIOD. INSPECTION NOTES: 1. THE INSPECTION SHALL BE PERRMED BY THE VENDOR AND WITNESSED BY FDOT. THE VENDOR SHALL NOTIFY FDOT AT LEAST 10 DAYS PRIOR TO COMPLETION OF INSTALLATION. THE VENDOR AND FDOT SHALL VERIFY JOINTLY THAT ALL INSTALLATION WORK IS CORRECTLY INSTALLED AND FUNCTIONAL. 2. THE VENDOR SHALL NOTIFY FDOT AT LEAST TWO DAYS PRIOR TO COMPLETION OF GROUNDING INSTALLATION R INSPECTION. ANY BELOW GRADE GROUNDING INSTALLATIONS AND GROUND CONNECTIONS SHALL NOT BE BACKFILLED UNTIL INSPECTED AND APPROVED BY THE FDOT. GROUNDING SHALL BE INSPECTED R PROPER CONNECTION TYPES, TIGHTNESS, WORKMANSHIP, AND CONRMANCE WITH THE APPROVED DESIGN. ANY EXOTHERMIC BONDS THAT ARE DEEMED UNSATISFACTORY SHALL BE REPAIRED BY THE VENDOR WITH NEW BONDS, WITHOUT CLAIM. 3. ALL SITES SHALL BE INSPECTED TO BE FREE OF DECOMMISSIONED EQUIPMENT AND DEBRIS; AND THAT EXCAVATIONS ARE BACKFILLED AND COMPOUND RESTORED. 4. LLOWING THE COMPLETION OF INSPECTIONS AND FDOT APPROVAL OF THE PERRMANCE AND TEST CRITERIA BY FDOT, THE INSTALLED EQUIPMENT AND FACILITIES SHALL BE SUBJECTED TO A 20-DAY PERRMANCE PERIOD. R THE PURPOSE OF THE SUCCESSFUL PERRMANCE PERIOD, FAILURE OF OPERATION IS DEFINED AS THE FAILURE OF A MAJOR COMPONENT OR SERVICE OPERATION OF THE SITE (NETWORK SERVICES ROUTING, ELECTRONIC EQUIPMENT, ANTENNAS, ETC.). FLORIDA EQUIPMENT INSTALLATION AND CUT-OVER SEQUENCING Notes \\dotscoteo1\traffic_ops_data\public\tsmo\telcom\\ Technology Replacement Plan\Phase 2 Contract Plans\Contract Plans\1-Notes\A-Notes vsd Attachment 1 6 A-6

7 Pensacola Chipley DOT 6 REPEATERS Tallahassee SR 6 Falmouth 6 DS-1 Yulee Jacksonville 2 5 REPEATERS 2 REPEATERS Lake City 5 REPEATERS Wildwood 2 REPEATERS Port Orange STATEWIDE ITS Communications NETWORK (sicn) PROPOSED NETWORK CONFIGURATION 3 REPEATERS Wilson Rd 5620 SAM 7750 Service Router 3 REPEATERS June Park 19 DS-1 Tampa DOT/FHP Tampa Maintenance 9 REPEATERS TURNPIKE 19 DS-1 2 REPEATERS Jacaranda Stuart Turnpike Repeater Site Stuart Maintenance 3 REPEATERS TURNPIKE McArthur TPK Repeater Site Naples McArthur 18 DS-1 Okeechobee Turnpike Site Coral Reef Turnpike Site KEYS MICROWAVE NETWORK FLORIDA PROPOSED NETWORK CONFIGURATION \\dotscoteo1\traffic_ops_data\public\tsmo\telcom\\ Technology Replacement Plan\Phase 2 Contract Plans\Contract Plans\1-Notes\A-Notes vsd A-7 Attachment 1 7