SELECTOR 4 / 8. Instrument for torque control ASL 11/17
|
|
- Candace Cannon
- 6 years ago
- Views:
Transcription
1 Instrument for torque control SELECTOR 4 / 8 ASL / ENGLISH Pictograms WARNING It can be dangerous to use this machine if the operating instructions are not carefully followed. Before using the machine, please read the instructions supplied carefully and keep them safe for future reference. ENGLISH Operator s Instructions Pages -6 Spare Parts and Accessories Ordering No.s Page 7 Edition Atlas Copco Tools No Page (8) 00 04
2 .0 Introduction These selectors are designed for up to 4 or 8 different sockets, and are easily connected to the I/O-port on the Tensor DS D3 or PF3000 Controller. No adapter cable is needed, only the communication cable and termination Both selectors work with Tensor DS D3 & PF3000, not with PF000 or Tensor DS D30. The basic functionality of the selector allows the operator to use the same tool for applications with different socket sizes and /or various torque levels, and automatically switch parameter set accordingly. Note Only ferro magnetic sockets can be used.0 Installation When installing the Selector 4/8 please follow instructions below.. Connectors Ref. No. +4 VDC input I/O -Bus cable/termination 3 Hex switch Fig Hex Switch There is a hex switch underneath the Selector(Fig. /Ref. No 3). Turn the switch to the right number/letter. The number indicates the node address on the I/O -Bus When delivered it is pre set to 5 for Selector 4 and 6 for Selector 8. For Tensor DS this should not be changed. For PF 3000, please read PF 3000 manual for detailed information Settings on Hex switch POS. 0 NODE ADDRESS Internal relay in PF3000. Not used A 0 B C D 3 E 4 F 5 Atlas Copco Tools - No
3 .3 Socket holders The socket holders are made of plastic. Holes shall be drilled so that the socket is close to the edge of the socket tray. The active region for the sensor for the socket is shown in Fig.. Make sure that the hole is drilled so that the socket is within this area. See drilling instructions below.. Remove the plate on the right side. Remove the plastic socket holders 3. Measure the sockets that you are going to use. 4. Place the socketholder upside down in a vice. 5. The hole for the socket is to be lined up with the edge of the guiding groove of the socketholder, as shown in fig. 3. Add approximately mm of space between the hole and the socket. Drill size (socket diameter + mm). 6. Drill the hole according to fig Repeat the procedure for every socket you are going to use. 8. Replace the socket holders in the order you want to have your P-sets. See chapter 5.0/ P-set Order. Fig. Sensor area Fig. 3 Edge of guiding groove Text slide On the text slide the name of the P-set can be attached, either with a permanent marker or more preferable written on a paper tag that is attached to the slide. Fig. 4 Socket name Atlas Copco Tools - No
4 .5 Dimensional drawing Fig Mounting Find a spot to mount the Selector on. It is recommended that you use the mounting brackets, position, and fixture it to the surface. Place it so it is possible to see the LED s, position, next to each socket. Screw size 4mm. Fig. 6 Ø Connectors and cables On the Selector there are two connectors for the I/O Bus. Both of these has to be connected. The drive is also equipped with two connectors for the I/O -Bus, which have to be connected as well. Every connector in the system has to be connected, either by a cable, (See page 8) or a termination, Fig. 7 shows how the I/O-bus accessories shall be connected. 4 Atlas Copco Tools - No
5 Fig. 7 Connections = Termination = Cable Atlas Copco Tools - No
6 3.0 LED s (Light Emitting Diodes) Tensor DS Red light = Socket lifted Green light = valid P-set chosen No light = P-set is not opened in drive Fig PF3000 Please read the PF3000 manual for detailed information. 4.0 P-set order Tensor DS The P-sets are listed in the same order as the socket position on the selector tray, starting from left. See Fig In order to turn on/off a position on the selector when connected to Tensor DS, open or delete the P-set corresponding to that position. PF3000 Please read the PF3000 manual for detailed information. Ref. No. P-set (Tensor DS) P-set (Tensor DS) 3 P-set 3 (Tensor DS) etc P-set (Tensor DS) 4 Red LED 5 Green LED 5.0 Power Supply The selector is powered from the DS drive or PF3000 through the I/O-Bus cable. The maximum current output from the DS/PF3000 is 800mA. If there is additional equipment connected to the DS/PF3000 which together with the selector consumes more than 800mA it is necessary to have external power supply. External power to the selector is connected on position in Fig., named ext 4 VDC Input. Note: External Power supply used, has to be insolated and apply to National standards. 6.0 Technical specifications Over all dimensions Length Selector 4 Length Selector 8 Width Height Weight Selector 4 Selector 8 Power consumption Selector 4 Selector 8 Operating voltage Operating conditions Temperature Humidity 0 mm 40 mm 0 mm 65 (75) mm. kg kg max 00 ma (normal 70 ma) max 40 ma (normal 70 ma) 4 VDC 0-50 o C (3- o F 5-95% non-condensing Shipment list Selector 4 or Selector 8 Socket holders, one for each position (not drilled) ( ) Mounting brackets terminations ( ) Operating manual 6 Atlas Copco Tools - No
7 Fig Spare parts & accessories For Selector Screw (MFTS M3x Black chrome) Text slide End plate Rubber seal (r) Rubber seal (l) Crystal emblem 6 Aluminium profile Socket holder 0 mm Socket holder 50 mm For Selector Screw (MFTS M3x Black chrome) Text slide End plate Rubber seal (r) Rubber seal (l) Crystal emblem 6 Aluminium profile Socket holder 0 mm Socket holder 50 mm Fig For Selector Foot Screw (MRT M4x0) 3 Base plate Mounting brackets For Selector Foot Screw (MRT M4x0) 3 Base plate Mounting brackets Sockets Cables available Ordering No meter meter meter meter meter meter 0 Ordering No mm Standard mm Accessory Atlas Copco Tools - No
SELECTOR 4 / 8. Instrument for torque control ASL 11/17
Instrument for torque control SELECTOR 4 / 8 ASL 11/17 3000840 ENGLISH Pictograms WARNING It can be dangerous to use this machine if the operating instructions are not carefully followed. Before using
More informationI / O Expander. Instrument for torque control ASL 11/17
Instrument for torque control I / O Expander ASL 11/17 3000920 ENGLISH Pictograms WARNING It can be dangerous to use this machine if the operating instructions are not carefully followed. Before using
More informationSignal Tower KombiSIGN 50
Signal Tower Simple operation thanks to bayonet mechanism WERMA was the first signal beacon manufacturer to offer a bayonet mechanism allowing elements to be mechanically and electrically connected within
More informationDS BAS /99 UNC 596 BUILDING AUTOMATION SYSTEM UNIVERSAL NETWORK CONTROLLER FEATURES
DS 13.321 BAS 2800+ 06/99 UNC 596 BUILDING AUTOMATION SYSTEM UNIVERSAL NETWORK CONTROLLER Specification no. 579-1-904 The Universal Network Controller (UNC 596) is fully intelligent and incorporates its
More informationTwo-stage lifting column - RKSlimlift /EM
Two-stage lifting column - RKSlimlift /EM Rod-shaped design and extremely quiet operation RKSlimlift RKSlimlift EM 4 fixing threads Simple connection Drive above the internal profile Large assembly surface
More information1 - Control and signalling units
Contents 0 - Control and signalling units Selection guide..............................................page /2. Control and signalling units Ø 8 et 2 b LED pilot lights, type XVL A...................................
More informationPower Focus 4000 Systems
Power Focus 4000 Systems DS DRIVE SYSTEMS 141 Power Focus Controller POWER FOCUS 4000 SYSTEMS Controller hardware: The Power Focus range controls tools from the Tensor S, ST,STR, DS and ETX families. The
More informationOperating instructions valve control box AS-i
THIS LEAFLET SHOULD BE KEPT IN A SAFE PLACE FOR REFERENCE Operating instructions valve control box AS-i 1 System description The Norgren Herion valve control box is used for controlling pneumatic swivel
More informationZAVIO Outdoor IR Mini Dome. Quick Installation Guide
ZAVIO Outdoor IR Mini Dome Quick Installation Guide 0 Quick Installation Guide Please follow the installation steps below to set up your IP Camera. Check the package contents with the list below. See P.1
More informationMultitronic. Technical data
Multitronic EMC Aluminium enclosure system for MCR technology Integrated guide grooves for PCB s External mounting slots with spring nuts Technical data Material: DIN EN 573 EN AW-AlMgSi Ingress protection:
More informationOperation mode. Output configuration. Relay DC SSR. Light-ON Dark-ON (switch selectable) Relay DC SSR. Relay DC SSR
Built-in Power Supply Photoelectric Sensor CSM DS_E_12_3 Model Contribute to Overall Cost Reduction erminal Block Models Easy to wire and adjust. For the most recent information on models that have been
More informationSit-Stand Monitor Arm
Sit-Stand Monitor Arm Product ID: ARMSTSCP1 This sit-stand monitor arm transforms your desk or tabletop into an ergonomic workstation. The monitor arm features a keyboard tray and easy height adjustment
More informationJIB EPT USER MANUAL. Please read this manual carefully before using the Alphatron JIB ETP unit! JIB & MOTORISED PAN AND TILT UNIT
JIB EPT JIB & MOTORISED PAN AND TILT UNIT USER MANUAL EN Please read this manual carefully before using the Alphatron JIB ETP unit! Thank you for purchasing a Alphatron product The EPT head is developed
More informationG12/G12x USER S MANUAL
G12/G12x USER S MANUAL TABLE OF CONTENTS SECTION 1 SLIDE CONFIGURATION SECTION 2 SLIDE CONFIGURATION ACCESSORIES SECTION 3 TABLETOP CONFIGURATION SECTION 4 TABLETOP CONFIGURATION ACCESSORIES SECTION 5
More informationPocket type SOUND LEVEL METER Model : SL-4030
Pocket type SOUND LEVEL METER Model : SL-4030 TABLE OF CONTENTS 1 FEATURES...1 2 SPECIFICATIONS...2 3 FRONT PANEL DESCRIPTION... 4 3-1 Electric condenser microphone... 4 3-2 Display...4 3-3 Power switch
More informationAll prices in CHF, excl. taxes, ex works Solothurn, payment within 30 days net
Price list 2018 Standard program Magnetic holding devices Dial test indicator holder Selecting magnet Demagnetizer Holding and sticking magnets Rubber magnets Conditions: Delivery terms: All prices in
More informationSpeed switches Programmable, digital speed switch With incremental encoder HOG 10
Features Freely programmable on and off switching speed Operation via included software (RS485 interface) Additional incremental signals (HTL/TTL) Combination with end shaft ø16 mm DSL.R: 3 outputs speed
More informationQuick Start Guide. SEB-710 I/O Expansion board. Introduction
SEB-710 I/O Expansion board Revision 1.0 - (March, 2011) Saflec Systems (Pty) Ltd Quick Start Guide Introduction The SEB-710 is an I/O expansion device for additional inputs and outputs. It has eight relay
More informationLaserLyte-Flex Red & Green Alignment System
LaserLyte-Flex Red & Green Alignment System LaserLyte-Flex The LaserLyte-Flex is an entry-level laser alignment system. It uses interchangeable optics and a semiconductor laser diode to project a highly
More informationUser s Manual. Models Digital Force Gauge. Additional User Manual Translations available at
User s Manual Models 475055 Digital Force Gauge Additional User Manual Translations available at www.extech.com Introduction Congratulations on your purchase of Extech s Model 475055 Digital Force Gauge
More informationNokeval. FD100 series. User Manual
Nokeval FD100 series User Manual Contents Document information... 2 FD100A4 and FD100A6 field displays... 3 Power supply connection... 4 Configuring... 5 Specifications... 7 Document information Device
More informationstandard, short, preferential, top
ipf electronic gmbh Kalver Straße 27 standard design short design preferential series top series standard, short, preferential, top norm sensing ranges, increased sensing ranges 1100 1 2 1100 norm sensing
More informationIncremental encoders Solid shaft with clamping or synchro flange pulses per revolution
GI55, GI56 Features Encoder with solid shaft ø mm or ø6 mm Max. 6000 pulses per revolution Optical sensing method Clamping or synchro flange Industrial standard High rotation speed up to 000 rpm Optional
More informationTwo-stage lifting column - RKSlimlift/EM
Two-stage lifting column - RKSlimlift/EM Rod-shaped design and extremely quiet operation RKSlimlift RKSlimlift EM 4 fixing threads 9Simple 9 connection Drive above the internal profile 9Large 9 assembly
More informationonlinecomponents.com
R General-Purpose Fiber-optic Sensor Compact Limit Switch Style with Universal Supply H FET output allows for solid state switching of AC or DC H Universal AC/DC power supply H Choose cable or connector
More informationInductive sensor NI3-EG08K-Y1-H1341
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 as per IEC 61508 Threaded barrel, M8 x 1 Stainless steel, 1.4427 SO DC 2-wire, nom. 8.2 VDC Output acc. to DIN EN 60947-5-6 (NA- MUR)
More informationInductive sensor BI1.5-EG08-Y1-H1341
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1
More informationOPERATION MANUAL FOR MICROPLATE ORBITAL SHAKER SERIES VP 325
OPERATION MANUAL FOR MICROPLATE ORBITAL SHAKER SERIES VP 325 TECHNICAL NOTE 276 Plate clip Plate clip Port for Customer Supplied 24 VDC AC Power Adapter Fig. 1. V&P Scientific Microplate Orbital Shaker.
More informationpanasonic.net/id/pidsx/global CCD The sensor can be used for various applications with its binary data output with four different sensing modes.
1123 PHOTO PHOTO PARTICUR Type Edge Sensor SERIES Related Information General terms and conditions... F-3 About laser beam... P.1593~ guide... P.1021~ General precautions... P.1595 Conforming to FDA regulations
More informationINSTALLATION INSTRUCTIONS:
INSTALLATION INSTRUCTIONS: Part # SV-5600 PC-F Full Frame Type (Black or Chrome) Part # SV-5500 PC-B Top Bar Type (Black or Chrome) Part # SV- PK Kits with PlateCam and 3.5 LCD monitor FEATURES: Revolutionary
More informationicore Kiosk system Installation Guide
icore Kiosk system Installation Guide The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages. All rights,
More informationFEMA ELECTRÓNICA. Series BDF. LARGE DISPLAYS for parallel BCD code. USER S MANUAL (HT r190307) BDF-xx-BCD for parallel BCD code
LARGE DISPLAYS BCD CODE Series BDF LARGE DISPLAYS for parallel BCD code BDF-xx-BCD for parallel BCD code FEMA ELECTRÓNICA IDEAL SOLUTION to display numerical values at long distances, controlled by parallel
More informationSpeed switches Programmable, digital speed switch With incremental encoder POG 10
Features Freely programmable on and off switching speed Operation via included software (RS485 interface) Additional incremental signals (HTL/TTL) EURO-flange B10 / shaft ø11 mm DSL.R: 3 outputs speed
More informationDelivery. Connection. C. AA+BB Helicoidal cable 2. Radial M12 8p CCW. 3. Radial M23 12p CCW
PROGRAMMABLE INCREMENTAL HOLLOW SHAFT ENCODER FOR INDUSTRIAL APPLICATIONS Programmable incremental optical encoder from 1 to 65.536 pulses per rotation Programmable via USB, without an additional programming
More informationAssembly Instructions for #5630 Medication PalWOW
Assembly Instructions for #5630 Medication PalWOW Before assembling, please familiarize yourself with all the parts and check to make sure you have all the parts as listed below. A B A & B - The box in
More informationProduct data sheet accessories control and regulation Accessories AIRWIN
Product data sheet accessories control and regulation BO-CT1 Continuous controller Item no. 6100101 Control of humidification performance BO-CT1 Option board 2 binary inputs Item no. 002212 Setpoint switching,
More informationMLS7A Series. Photoelectric Sensors. Heavy-Duty Retro-Reflective Sensors. Photoelectric MLS7A Series Heavy Duty PEPPERL+FUCHS 529
Retro-Reflective Mode See page 53 Sensing Ranges: 3m Outputs: NPN MLS7A Series Heavy-Duty Retro-Reflective Sensors Heavy Duty Cast aluminium housing Side mount or flange mount Photoelectric MLS7A Series
More informationAbsolute encoders - bus interfaces
Features Absolute encoder multiturn Optical sensing method Max. resolution: singleturn 18 bit, multiturn 16 bit LED status indicator PROFINET IO Maximum resistant against magnetic fields Optional EAL580
More informationE3S-A. Built-in Amplifier Photoelectric Sensor (Medium Size) Ordering Information. Built-in Amplifier Photoelectric Sensors. Horizontal. 7 m.
Built-in Amplifier (Medium Size) ES-A CSM_ES-A_DS_E Be sure to read Safety Precautions on page 0. Ordering Information Built-in Amplifier s Red light Infrared light Sensing method Appearance Connection
More informationAPS4 Inductive Proximity Sensors
APS4 Inductive APS4-S-E-D APS4-S-E2-D APS4-M-E-D APS4-M-E2-D Compact x27 mm plastic DC 4 models available Compact polycarbonate housing; comes with mounting plate High-frequency oscillation type DC 3-wire,
More informationCounters, Process Displays, Timers, Tachometers. Product overview
Counters, Process Displays, Timers, Tachometers Product overview Totalizers mechanical Stroke counters Three designs, optional with 5-, 6- or 7-digit display. Manual reset Surface mount with mounting plate
More informationConductor and Cable Marking Description and Handling
Conductor and Cable Marking Description and Handling 566 Wire marking The following markers are available: Markers for plotter marking. Markers on roll for thermal transfer printing. Remove the printed
More informationIncremental encoders Solid shaft with EURO flange B pulses per revolution
Solid shaft with EURO flange B 0 5000 pulses per revolution EIL580 - EURO flange B - OptoPulse Features Size ø58 mm Precise optical sensing Output signal level TTL or HTL EURO flange B Connection axial,
More informationInductive sensor BI1.5-EG08-Y1-H1341
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1
More informationA Global Laser Brand. LDM150, Sigma, LDM115, LDL175, LCG115 & LLM115
A Global Laser Brand LDM150, Sigma, LDM115, LDL175, LCG115 & LLM115 Imatronic is a family of industry-standard laser diode modules from Global Laser. The ruggedised metallic housing of Imatronic lasers
More information4. Sensing Distance. 2: 2 mm. 4: 4 mm 8: 8 mm 15: 15 mm 16: 16 mm 20: 20 mm
Inductive Sensor Double Sensing Distance Model Number Legend SALIENT FEATURES IP - 7, Brass Housing Short - Circuit protection Reverse Polarity Protection Shielded and Non - Shielded Prewired and Connector
More informationAI-102. IR Illuminator. Installation Guide. Rev IP Surveillance
AI-102 IR Illuminator Installation Guide Rev. 1.1 IP Surveillance Revision History: Rev. 1.0: Initial release Rev. 1.1: Changed effective IR range and power consumption. AI-102 Tube Type Infrared Illuminator
More informationWall-Mounted Sit-Stand Desk - Single Monitor
Wall-Mounted Sit-Stand Desk - Single Monitor Product ID: WALLSTS1 This wall-mounted sit-stand desk is perfect for areas that don t have enough space for a traditional sitstand desk. Its compact, wall-mounted
More informationDIGITAL DISPLAY. for Industry Applications. Series WAY-D. Key-Features:
DIGITAL DISPLAY for Industry Applications Series WAY-D Key-Features: Content: Technical Data.2 Technical Drawing...2 Electrical Connection...3 Programming...5 Control s...6 Order Code & Accessories...7
More informationTM3DI16 module TM3-16 inputs
Characteristics module TM3-16 inputs Main Range of product Product or component type Range compatibility Jun 30, 2018 Modicon TM3 Discrete input module Modicon M241 Modicon M251 Modicon M221 Discrete input
More informationNA1-5. Ultra-slim Body 25mm Beam Pitch Area Sensor. Even a Slim Hand Is Detected by the 25mm Pitch Beam Curtain AREA SENSORS.
Ultra-slim Body 2mm Pitch Area Sensor mm Thick: /2 of Conventional Model It fits into a small space, without obstructing normal operation. Clearly Visible Job Indicator Both the emitter and the receiver
More informationDIGITAL LASER SENSOR. User friendly, high precision Digital Laser Sensor SERIES mm in. Easy 1 Installation.
LS SERIES DIGITAL LASER SENSOR Multi-voltage User friendly, high precision Digital Laser Sensor Conforming to EMC Directive Conforming to FDA regulations Easy Installation We designed types of sensor heads
More informationMu-checker To support building the system with automatic measuring unit or dedicated gages
7 24 7 3.5 16 Mu-checker To support building the system with automatic measuring unit or dedicated gages SERIES 519 Mu-checker (Electronic micrometer) Probes (Lever head / Cartridge head) Lever heads Order
More informationPrintheads HP TIJ 2.5
Printheads HP TIJ 2.5 PREMIUM Premium printheads for use with a series of HSAJET controllers utilizing the HP TIJ 2.5 technology HSAJET and HP TIJ 2.5 technology HSAJET printers use HP thermal inkjet technology
More informationThe SLC/SLG 415 system: Safety light curtains and grids with integrated muting function
The SLC/SLG 415 system: Safety light curtains and grids with integrated muting function The SLC/SLG 415 system: Safety light curtains and grids with integrated muting function EN 61496-1/-2 The muting
More informationME PLC Multifunctional housing for complex electronics. Data sheet _en_01. 1 Description
Multifunctional housing for complex electronics Data sheet 105504_en_01 PHOENIX CONTACT 2013-04-08 1 Description The housings of the ME PLC 40... product group consist of a 40-mm wide housing base with
More informationDocumentation. AL225x Connector-Box. Accessory for servo drives of the series AX5000 and AX2000. Version: Date:
Documentation Accessory for servo drives of the series AX5000 and AX2000 Version: Date: 1.8 2018-01-16 Contents Contents 1 Foreword... 5 1.1 Notes on the documentation... 5 1.2 Documentation Issue Status...
More informationOrganisational Kitchen Fittings Drawer and Front Extensions
GRASS NOVA PRO TOUCH LATCH SENSO Application: For drawer and front pull-out Material: Steel, plastic, aluminium Finish: Zinc plated, powder coated Opening version: Full extension with self opening mechanism
More informationDEFLECTION AND TWIST MEASUREMENT SYSTEM (DTMS) Model 47
Features DEFLECTION AND TWIST MEASUREMENT SYSTEM (DTMS) Model 47 Results are not affected by the motion or acceleration of the structure being tested Three or five degrees of freedom are measured between
More informationWALL MOUNTED PANEL. SECTION 2G (Rev.E) SECTION CONTENTS. Download from Technical Manuals area. sec.2g SMYLE WALL-MOUNTED PANEL 2
SECTION G (Rev.E) 8 WALL MOUNTED PANEL 8 Download from www.urmet.com Technical Manuals area. SMYLE WALL-MOUNTED PANEL SECTION CONTENTS SPECIAL MODULES...8 TECHNICAL FEATURES... DOOR UNITS... Door phone
More informationRER 123 Bus Connection Module. Technical Description
Bus Connection 1MRS751143-MUM Issued: 06.11.1998 Version: E/08.07.2005 Bus Connection 1. About this manual...4 1.1. Copyrights...4 1.2. Trademarks...4 1.3. Guarantee...4 2. Safety information...5 3. General...6
More informationKombiSIGN 71 - Signal Tower
KombiSIGN 71 - Signal Tower Size comparison KombiSIGN 71/40 Signalisation Index Optical Audible 2 tone/8 tone 105 db Siren Vocal element Permanent Light 2 Continuous tone 3 5 LED Permanent Light 2 Pulse
More informationF3S-B. Safety Design for Category 2. Suitable for Detecting Human Bodies in a Dangerous Area. Safety Light Curtain. Features
Safety Light Curtain Suitable for Detecting Human Bodies in a Dangerous Area Safety Design for Category 2. Features The is a type 2 Safety Light curtain intended to be used as or with the safety related
More informationRTT2 ROOM TEMPERATURE SWITCH. Mounting and operating instructions
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA STANDARDS OPERATIONAL DIAGRAMS WIRING AND CONNECTIONS
More informationTM3DI16G module TM3-16 inputs spring
Characteristics module TM3-16 inputs spring Main Range of product Product or component type Range compatibility Modicon TM3 Discrete input module Modicon M221 Modicon M241 Modicon M251 Discrete input number
More informationLiner Shield AC XB CW
The is an IP66- rated, AC line input, linear lighting fixture equipped with 18, 27, or 36 high brightness LEDs, dedicated to project an intense even light spread to brightly wash any flat surface with
More informationOptical encoding film disc mini board with integrated infrared photo sensor and LED operating indicator round, 5-pin output socket (180, DIN 41524)
Quick reference 200 pulses per revolution of measuring drum For use with TG05 to TG50 and BG4 to BG100 Uni-directional Not applicable for ex-proof areas Application The Pulse Generator for RITTER Drum-type
More informationPANELITE ENCLOSURE LIGHTS OVERVIEW
SPEC-00581 H763.422.2211 763.422.2600 ELECTRICAL LIGHTING PACKAGES ELECTRICAL LIGHTING PACKAGES PANELITE ENCLOSURE LIGHTS OVERVIEW FEATURES Slim profile allows light to be tucked up out of the way for
More informationLinear Positioning Stage Reference Manual
PP-30 Series Linear Positioning Stage PP-30 Piezo Positioner Stage Rev 3.00 MICRONIX USA, LLC 15375 Barranca Parkway, E-106 Irvine, CA 92618 Tel: 949-480-0538 Fax: 949-480-0538 Email: info@micronixusa.com
More informationPanorama rudder indicator TRI-2 Analogue or CAN input Approved according to MED Three extra large scales Long-life LED illumination Built-in dimmer
USER'S MANUAL Panorama rudder indicator TRI-2 Analogue or CAN input Approved according to MED Three extra large scales Long-life LED illumination Built-in dimmer DEIF A/S Frisenborgvej 33 DK-7800 Skive
More informationAS-i Safety Input Modules (M12), IP67
Input Modules (), IP67 Input Modules (), IP67 for opto, floating contacts or complementary switch Applications up to category 4/PLe/SIL 3 (Figure similar) Figure Type Inputs, SIL 3, cat. 4 4 x, 4 x, 4
More information2M IR Mini Dome Quick Installation Guide
1 2M IR Mini Dome Quick Installation Guide Please follow the installation steps below to set up 2M IR Mini Dome IP Camera. Check the package contents against the list below. See P.1 Physical overview.
More informationMagnetic Field Sensor Magnetic-inductive Proximity Sensor BIM-M12E-Y1X-H1141
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1
More informationPowerCore Model TEC-10 Installation Manual
PowerCore Model TEC-10 Installation Manual Products covered in this document comply with European Council electromagnetic compatibility directive 2014/30/EU and electrical safety directive 2014/35/EU.
More informationDXTH DUCT SENSOR / SWITCH FOR TEMPERATURE AND HUMIDITY. Mounting and operating instructions
DUAL DUCT SENSOR / SWITCH FOR TEMPERATURE AND HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL
More informationModel HT Microplate Orbital Shaker. Product Manual
Big Bear, Inc. Pleasanton, CA USA 94566 Tel: 510-333-4338 Fax: 925.397.3148 Email: Sales@.com Web: www..com Manual Version: 1.00 Manual Date: 090103 Filename: HT91000Manual.pdf Copyright 2003 Big Bear,
More informationElectropneumatic miniature control valves Mounting Connectors Minisolenoid valves Indicators LED seals LED Valve modules Poppet 3/2 single pilot 4/2 s
ElectroPneumatic Miniature Control Valves Order/Technical Support Tel: (800) 6773 / FAX: (800) 677386 / www.crouzetusa.com /47 Electropneumatic miniature control valves Mounting Connectors Minisolenoid
More informationEBC Mini-ITX Chassis for High Power Consumption Applications Version: 1.0. Quick Installation Guide ABOUT COMPATIBLE SBC/COOLING KIT
EBC-3000 Mini-ITX Chassis for High Power Consumption Applications Version:.0 Quick Installation Guide ABOUT The EBC-3000EBC-3000 is designed for Mini-ITX motherboards. The front panel includes spaces for
More informationOPERATION MANUAL. Green power, Hybrid power Auto range, A/C weighting SOUND LEVEL METER. Model : SL-4113G. Your purchase of this
Green power, Hybrid power Auto range, A/C weighting SOUND LEVEL METER Model : SL-4113G Your purchase of this SOUND LEVEL METER marks a step forward for you into the field of precision measurement. Although
More informationGlobal Water Instrumentation, Inc.
Instrumentation, Inc. 11390 Amalgam Way Gold River, CA 95670 T: 800-876-1172 Int l: (916) 638-3429, F: (916) 638-3270 Display: EZ100 11/12/04-1 - Congratulations on your purchase of the EZ100 Display.
More informationMULTI ROTARY SWITCH MR50
MAIN FEATURES 1 / 2 " SELECTOR SWITCH Dimensions Ø ½ (12.7 mm) Switching mode: Shorting or non-shorting Selector switch positions up to 16 Switching torque up to 6 Ncm Gold plated contacts Rugged design
More informationIncremental Encoder with Hollow Shaft
Incremental Encoder Type RI 36-H n miniature industry encoder for high number of pulses n short mounting length n easy mounting procedure n Application e.g.: - Motors - Machine tools - Packaging Machines
More informationOperating instructions Safety sensor BNS About this document. Content
Safety sensor BNS 0. About this document Operating instructions.............pages to 6 Original. Function This operating instructions manual provides all the information you need for the mounting, set-up
More informationInstallation Guide DRAFTMF4100
Installation Guide MF4100 This Class B digital apparatus complies with Canadian ICES-003 Cet appareill numérique de la classes B est conform à la norme NMB-003 du Canada This device complies with Part
More informationProduct description. At a glance. performance in a metal housing coating available Precise autocollimation optics. sensors
-2 Laser Small photoelectric sensors High-performance photoelectric sensor family with laser optics Product description At a glance performance in a metal housing coating available Precise autocollimation
More informationKINAX WT720 absolute, programmable angular postion transmitter
For industrial applications in rough environments KINAX WT720 is a robust, absolute angular position transmitter, which is particularly suited to applications in rough environments due to its unique capacitive
More informationPrintheads HP TIJ 2.5
Printheads HP TIJ 2.5 Premium New Premium printheads for use with a series of new printer controllers utilizing the HP TIJ 2.5 technology HSAJET and HP TIJ 2.5 technology HSAJET printers use HP thermal
More informationH Series PLC. ! : Indicates Compulsion. EH-150 Analog input module EH-AXH8M Instruction manual. Safety precautions DANGER CAUTION COMPULSION
H Series PLC EH-150 Analog input module EH-AXH8M Instruction manual Thank you for purchasing a Hitachi Programmable Logic Controller. To operate it safely, please read this instruction manual and all the
More informationIF-80x Outdoor Terminal
95-10330_IF-800 V2016-10-20 Outdoor Terminal IF-80x Outdoor Terminal 1 IF-800 Outdoor / IF-801 We are pleased that you have decided to use a terminal of the IF-80x series for recording access data. Scope
More informationBreezeMAX Wi² and BreezeACCESS Wi² Quick Installation Guide
This Quick Installation Guide is intended for experienced installers. For more information refer to the relevant sections in the BreezeMAX Wi² and BreezeACCESS Wi² System Manual. Wi² Package Content Check
More informationSAX / PAX Test Blocks & Probes
SAX / PAX Test Blocks & Probes Reference Handbook sax-reference-en v.58 Copyright Notice All information provided in this document is the property of SECUCONTROL. SECUCONTROL grants its customers or potential
More informationNO: PH-185 PRODUCT: E3JK Photoelectric Sensors DATE: May 2014 TYPE: Discontinuation Notice
NO: PH-185 PRODUCT: E3JK Photoelectric Sensors DATE: May 2014 TYPE: Discontinuation Notice E3JK Universal AC/DC Supply Voltage Photoelectric Sensors to be Discontinued February 2015; Replace with E3JM
More informationABSOLUTE ROTARY ENCODER INTERBUS
Main Features - Compact and heavy duty industrial model - Interface: Remote-Bus - ENCOM-Profile: K3 (programmable) - Housing: 58 mm - Shaft: 6 or 10 mm, hollow- 15 mm - Resolution: max. 25 Bit = 33,554,432
More informationSERIE 59. Rear clamp. Frontal clamp HIGH RESOLUTION HOLLOW SHAFT INCREMENTAL ENCODER FOR INDUSTRIAL APPLICATIONS
HIGH RESOLUTION HOLLOW SHAFT INCREMENTAL ENCODER FOR INDUSTRIAL APPLICATIONS Resolution up to 50.000 pulses per turn External diameter 58 mm Hollow shaft from Ø 10 to 14 mm Protection class IP67 according
More informationMHP PHOTOELECTRIC. Sensors and Switches NOTICE GENERAL INFORMATION
MHP PHOTOELECTRIC Catalog Listing Description SDS-C2MHP-R-G retroreflective, infrared, range 18 ft. (5,5 m) SDS-C2MHP-D-G diffuse, infrared, range 18 in. (457,2 mm) SDS-C2MHP-P-G polarized retroreflective,
More informationRТTH DUAL ROOM SWITCH
DUAL ROOM SWITCH FOR TEMPERATURE AND RELATIVE HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA
More informationDC Outdoor Power Supply/Chargers
DC Outdoor Power Supply/Chargers Installation Guide Models Include: WayPoint3 WayPoint7-2.5A @ 12VDC or 24VDC. - 6A @ 12VDC or 24VDC. - 115/230VAC input. - 115VAC input. WayPoint5 WayPoint7V - 4A @ 12VDC
More informationS 180 OPTICAL AND AUDIBLE MODULAR DEVICES. This is our idea that lead us to create and engineering this modular lamp. MODULAR CONFIGURATION
S 180 OPTICAL AND AUDIBLE MODULAR DEVICES S180 a custom made lamp This is our idea that lead us to create and engineering this modular lamp. custom solutions keeping minimized costs and stock 10 different
More informationVersion-E Manual PR1a. Photocell. Manual. Page 1
Version-E16-06-02 Photocell Manual Page 1 Important Information General Before using your ALGE-TIMING device read the complete manual carefully. It is part of the device and contains important information
More information2m Cable Emitter 10-30V DC. Quick Disconnect Emitter 10-30V DC. (Euro Style) 10-30V DC (Euro Style) 2m Cable NPN 10-30V DC. Quick Disconnect NPN
Thru-beam Mode / Retroreflective Mode T8 SERIES Sensing Mode Appearance Supply Voltage Output Mode Part Number Emitter T8-T2MD-EY9C2L2 T8-T2MN-CY9C4U2 T8-T2MP-CY9C4U2 / Emitter T8-T2MD-EY9Q4LE T8-T2MN-CY9Q4UE
More information