How to Create a Fountain Pen
|
|
- Stephen Foster
- 5 years ago
- Views:
Transcription
1 How to Create a Fountain Pen Lesson 4 How to Create a Fountain Pen This lesson will guide you in building a fountain pen. You will use the following tools: NURBS curves. Extrusion. Mirror. Trim. Blend Curves. Lathe. Edge Extract. Fill Path. Birail. Learning solidthinking 1
2 Lesson 4 Building the pen nib 1) If you are already working with solidthinking, choose the New command from the File main menu and save the scene you were working on. Otherwise, you must first run solidthinking. 2) Choose the default layout option from the Layouts panel (choose View 4 Layouts). 3) Open the Grid Setup panel by either selecting Edit 4 Grid Setup. 2 Learning solidthinking
3 How to Create a Fountain Pen 4) Choose the Grid#1 tab and set X, Y, and Z to 0.1. Let s now begin by modeling the pen-nib. 5) Click the Ellipse: focuses, point. As focuses coordinates use points Focus1 = 0.6, 0, 0 and Focus2 = -0.6, 0, 0; as Point1 use coordinates 1.2, 0, 0.2. Learning solidthinking 3
4 Lesson 4 6) Select now the ellipse and insert Start angle = 10 and End angle = 170 in the Modeling Tool panel. 4 Learning solidthinking
5 How to Create a Fountain Pen 7) Click the Extrude icon (with the Front view active) and extrude the ellipse with a value of 6.9. Your object should look like the one below. Now you have to follow the red outline as in the next figure and draw a profile in the area which will then be tour Trim curve. 8) Click the Top View and click activate the NURBS curve icon to start inserting the points. The Local axes origin is always at the default value of 0,0,0. Insert the following points: #1(0, 0, 0), #2(1.2, -2.75, 0), #3(1.35, -2.85, 0), #4(1.2, -3, 0), #5(0.81, -6.9, 0). Learning solidthinking 5
6 Lesson 4 9) Click the Mirror icon, select the NURBS curve and press Spacebar to close the selection. Define now the X axis as your Reflection Axis. 6 Learning solidthinking
7 How to Create a Fountain Pen 10) Click the Trim surface function and select the right curve followed by the extruded ellipse. You will so perform a trimming onto the surface. Repeat the procedure for the left curve. This should be your resulting surface. To obtain the inner portion of the object and thus create your nib, switch on the Trim exterior radio button in the Loop exterior section of the Modeling Tool section. Learning solidthinking 7
8 Lesson 4 Here is your pen-nib. Let s now move on to the body of the pen. 11) Open the Right View to full size (simply double-click the title bar) and draw the following curves using the NURBS curve tool. Curve1: #1(0, -4.1, 1); #2(0, -4.1, 1.3); #3(0, -4.1, 1.4); #4(0, -4.2, 1.5); #5(0, -4.3, 1.4); #6(0, -4.5, 1.5); #7(0, -4.7, 1.5). 8 Learning solidthinking
9 How to Create a Fountain Pen Curve 2: #1(0, -4.7, 1.5); #2(0, -8.2, 1.5). Curve 3: #1(0, -8.2, 1.5); #2(0, -8.2, 1.6); #3(0, -8.3, 1.6); #4(0, -8.4, 1.7); #5(0, -8.7, 1.8); #6(0, -10, 1.8). Learning solidthinking 9
10 Lesson 4 Curve 4: #1(0, -10, 1.7); #2(0, -11.6, 2.3); #3(0, -14.6, 2.4); #4(0, -16.4, 2). Curve 5: #1(0, -16.4, 2); #2(0, -16.4, 2.1); #3(0, -16.5, 2.1); #4(0, -19.1, 1.8); #5(0, -21.7, 1.8); #6(0, -35.2, 1.8). 10 Learning solidthinking
11 How to Create a Fountain Pen Creating the revolved surfaces and using Round To obtain the body of the fountain pen you can use the Lathe modeling tool, which creates revolved surfaces by rotating around any user-defined axis. 1) Click the Lathe icon or choose the Tools 4 Surfaces 4 Lathe command. 2) Click Curve 1 and press Enter to confirm the following values in the console: Rotation = 360; Revolution Axis = 0, 0, 0; Revolution axis direction = Y. Do the same with Curves 2 and 3. 3) Click Curve 4 and press Enter to confirm the following values in the console: Rotation = 360; Revolution Axis = 0, 0, 0; Revolution axis direction = Y. Do the same with the Curves 5. Learning solidthinking 11
12 Lesson 4 Now you need to seal the back portion of the pen.. 4) Click the Edge extract icon and click the hollow surface. The surface will turn green and you will have to select the edge to be extracted as you can see in the figure. Click this edge 12 Learning solidthinking
13 How to Create a Fountain Pen 5) Click now the Fill path icon and then click the curve you have just extracted. With this procedure, you will cover up the hole. 6) Click the Combine icon and click first the revolution surface (object A), then the filled hole (object B). Press Spacebar. to end the command. A B Learning solidthinking 13
14 Lesson 4 7) Click now the Round tool. Confirm Tolerance and sew tolerance value by pressing Enter. Pick the surface, then the edge and press Spacebar. 8) At the Radius prompt type 0.3. Edge to pick Rounded Edge 14 Learning solidthinking
15 How to Create a Fountain Pen 9) Click the Edge extract icon and click the hollow surface in the front side of the pen.. Select the inner edge as shown in the figure. 10) Click the Fill path icon and then click the curve you have just extracted. You can select it also in the World browser. With this procedure, you will cover up the hole. Learning solidthinking 15
16 Lesson 4 This is what your pen should look like. At this point, only the clip present in the pen cap is missing. 11) Activate the Right View, click the NURBS curve icon and draw the following curves. Curve Top: #1(0, -33.1, 2.6); #2(0, -28.1, 3.8); #3(0, -23.7, 2.9); #4(0, -22.7, 2.4); #5(0, -22.5, 2); #6(0, -22.5, 1.9). 16 Learning solidthinking
17 How to Create a Fountain Pen CurveBottom: #1(0, -33, 1.8); #2(0, -31.3, 2.6); #3(0, -27.8, 3.2); #4(0, -26, 3.1); #5(0, -24.6, 2.8); #6(0, -23.4, 2.6); #7(0, -23.1, 2.2); #8(0, -22.9, 1.9); #9(0, -22.5, 1.9). 12) Click now the Circle: center, radius icon and accept all the default values. 13) Click the Birail icon and select the Profile curve (Circle), Rail curve #1 (Curve Top) and Rail curve #2 (Curve Bottom). You will so obtain the pin. Learning solidthinking 17
18 Lesson 4 14) Click the Sphere icon and accept the default Local Axes Origin = 0, 0, 0 and Radius = 1. 15) Use the Translate command to position the Sphere as in the figure below. 18 Learning solidthinking
19 How to Create a Fountain Pen You have so reached the end of this lesson. Your fountain pen should be similar to the one you see in the following figure. Learning solidthinking 19
20 Lesson 4 20 Learning solidthinking
Designing a Chair. Lesson 6
Designing a Chair Lesson 6 Designing a Chair This lesson will show you how to design a chair by using the Curves Network modeling tool in a few steps. We will focus your attention on the following modeling
More informationDesigning a Chair. Lesson 6
Lesson 6 Designing a Chair This lesson illustrates how to design a chair using the Curves Network modeling tool. The following modeling tools will be covered: Curves Network. Skin. Intersect. Trim. Mirror.
More informationTutorial - Steering Wheel
Tutorial - Steering Wheel (written by Jacob Tremmel, Student at Altair) This tutorial is about modeling (CAD) and rendering of a Steering Wheel with Altair s solidthinking Evolve 9.0. 1 Modeling 1. At
More informationModeling a CPU case. Lesson 5. This tutorial illustrates how to create the external case of a Central Processing Unit using the following commands.
Modeling a CPU case Lesson 5 Modeling a CPU case This tutorial illustrates how to create the external case of a Central Processing Unit using the following commands. NURBS curves. Pipe. NURBS surface editing.
More informationuser manual vol. 2: modeling
user manual vol. 2: modeling An Company solidthinking Release 8.0 User Manual Modeling - Volume 2 1993-2009 solidthinking Inc. Part N. 80-25041-10301 Copyright 1993-2009 solidthinking, Inc. All rights
More informationsolidthinking Environment...1 Modeling Views...5 Console...13 Selecting Objects...15 Working Modes...19 World Browser...25 Construction Tree...
Copyright 1993-2009 solidthinking, Inc. All rights reserved. solidthinking and renderthinking are trademarks of solidthinking, Inc. All other trademarks or service marks are the property of their respective
More informationsolidthinking User Interface
Lesson 1 solidthinking User Interface This lesson introduces you to the solidthinking interface. The functions described represent the tools necessary for effectively managing the modeling of a project.
More informationTextures. Textures. Lesson 9
Lesson 9 Textures In this lesson we are going to analyze the use of textures. You will look at two specific examples of material, for which the use of textures is essential to obtain a correct result:
More informationChapter 10. Creating 3D Objects Delmar, Cengage Learning
Chapter 10 Creating 3D Objects 2011 Delmar, Cengage Learning Objectives Extrude objects Revolve objects Manipulate surface shading and lighting Map artwork to 3D objects Extrude Objects Extrude & Bevel
More informationInventor 201. Work Planes, Features & Constraints: Advanced part features and constraints
Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the
More informationExtrude & Revolve Maya 2013
2000-2013 Michael O'Rourke Extrude & Revolve Maya 2013 Concept There are several basic modeling techniques shared by all 3D programs These can be used either to create your final model For example, a vase
More informationChapter 6: Create Surfaces from Curves
A common way of working in 3-D is to draw curves that represent edges, profiles, cross-sections, or other surface features and then to use surfacing commands to create surfaces from those curves. Edge
More informationCATIA V5 Parametric Surface Modeling
CATIA V5 Parametric Surface Modeling Version 5 Release 16 A- 1 Toolbars in A B A. Wireframe: Create 3D curves / lines/ points/ plane B. Surfaces: Create surfaces C. Operations: Join surfaces, Split & Trim
More information3D Design with 123D Design
3D Design with 123D Design Introduction: 3D Design involves thinking and creating in 3 dimensions. x, y and z axis Working with 123D Design 123D Design is a 3D design software package from Autodesk. A
More informationTRAINING GUIDE SOLIDS-LESSON-3
TRAINING GUIDE SOLIDS-LESSON-3 Mastercam Training Guide Objectives You will generate the solid model from the existing 2-dimensional geometry. This Lesson covers the following topics: Open an existing
More informationStructural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment
ANSYS Workbench Tutorial Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
More informationExercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
More informationStructural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment. Kent L. Lawrence
ANSYS Workbench Tutorial Structural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
More informationModeling a Gear Standard Tools, Surface Tools Solid Tool View, Trackball, Show-Hide Snaps Window 1-1
Modeling a Gear This tutorial describes how to create a toothed gear. It combines using wireframe, solid, and surface modeling together to create a part. The model was created in standard units. To begin,
More informationCharacter Modeling IAT 343 Lab 6. Lanz Singbeil
Character Modeling IAT 343 Lab 6 Modeling Using Reference Sketches Start by creating a character sketch in a T-Pose (arms outstretched) Separate the sketch into 2 images with the same pixel height. Make
More informationRHINO; AN INTRODUCTION + FAKING TRABECULAE; EndOfLine.info;
RHINO; AN INTRODUCTION + FAKING TRABECULAE; EndOfLine.info; Rhinoceros is a relatively simple program with an AUTOCAD based interface. The disadvantage of this type of interface is a series of terms need
More informationCreate a Rubber Duck. This tutorial shows you how to. Create simple surfaces. Rebuild a surface. Edit surface control points. Draw and project curves
Page 1 of 24 Create a Rubber Duck This exercise focuses on the free form, squishy aspect. Unlike the flashlight model, the exact size and placement of the objects is not critical. The overall form is the
More informationSolid Modeling: Part 1
Solid Modeling: Part 1 Basics of Revolving, Extruding, and Boolean Operations Revolving Exercise: Stepped Shaft Start AutoCAD and use the solid.dwt template file to create a new drawing. Create the top
More informationExtrusion Revolve. ENGR 1182 SolidWorks 02
Extrusion Revolve ENGR 1182 SolidWorks 02 Today s Objectives Creating 3D Shapes from 2D sketches using: Extrusion Revolve SW02 In-Class Activity Extrude a Camera Revolve a Wheel SW02 Out-of-Class Homework
More informationAutodesk Inventor 6 Essentials Instructor Guide Chapter Four: Creating Placed Features Chapter Outline This chapter provides instruction on the follow
Chapter Four: Creating Placed Features Chapter Outline This chapter provides instruction on the following topics and provides exercises for students to practice their skills. Day Two Topic: How to create
More informationMaya Lesson 3 Temple Base & Columns
Maya Lesson 3 Temple Base & Columns Make a new Folder inside your Computer Animation Folder and name it: Temple Save using Save As, and select Incremental Save, with 5 Saves. Name: Lesson3Temple YourName.ma
More informationLecture 4, 5/27/2017, Rhino Interface an overview
數字建築與城市设计 Spring 2017 Lecture 4, 5/27/2017, Rhino Interface an overview Copyright 2017, Chiu-Shui Chan. All Rights Reserved. This lecture concentrates on the use of tools, 3D solid modeling and editing
More informationAutodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently
More informationIntroduction to AutoCAD 2012
Introduction to AutoCAD 2012 Alf Yarwood Chapter 13 Exercise 1 1. Open AutoCAD 2012 with a double-click on its shortcut icon in the Windows desktop. 2. Open the template acadiso3d.dwt. 3. Make two new
More informationDave s Phenomenal Maya Cheat Sheet Polygon Modeling Menu Set By David Schneider
Dave s Phenomenal Maya Cheat Sheet Polygon Modeling Menu Set By David Schneider POLYGONS NURBS to Polygons This allows the user to change the objects created with NURBS into polygons so that polygon tools
More informationNURBS modeling for Windows. Training Manual Level 1
NURBS modeling for Windows Training Manual Level 1 Rhino Level 1 Training 2nd Ed.doc Robert McNeel & Associates 1997-2000 All Rights Reserved. Printed in U.S.A. Copyright by Robert McNeel & Associates.
More informationEach trainee receives the official 260 page courseware as part of attending this course.
Level 1 NURBS modelling with Rhino Course Outline This course is for anyone new, or nearly new, to Rhino. Recognised as THE introductory course for Rhino, all trainees receive an Official Certificate on
More informationAdditional Exercises. You will perform the following exercises to practice the concepts learnt in this course:
Additional Exercises You will perform the following exercises to practice the concepts learnt in this course: Master Exercise : Mobile Phone Plastic Bottle Exercise 1 Master Exercise : Mobile Phone In
More informationMaya 2014 NURBS Modeling Tutorial Airship
Maya 2014 NURBS Modeling Tutorial Airship Airships have captured human imagination for centuries and are featured prominently in books, film and video games. As an introduction to modeling with NURBS (non
More informationFeature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05
Feature-Based Modeling and Optional Advanced Modeling ENGR 1182 SolidWorks 05 Today s Objectives Feature-Based Modeling (comprised of 2 sections as shown below) 1. Breaking it down into features Creating
More informationCOMPUTER AIDED DESIGN CURRICULLOM RHINO BASED 3D DESIGN
COMPUTER AIDED DESIGN CURRICULLOM RHINO BASED 3D DESIGN S.no. CONTENTS Page no S. no. CONTENTS PAGE no. 1. Introduction 1 2. Necessary of Rhino in Designing 2 3. Working with 3D Models 3 4. Object Types
More informationFOLLOWING ALONG THE PATH
FOLLOWING ALONG THE PATH 3D MODULE 18 OBJECTIVES At the completion of the Module you should be able to: Create a solid model by extruding a profile along a predefined pathway. Use the Press/Pull command
More informationAutoCAD and Its Applications ADVANCED Surface Modeling Tutorial
AutoCAD and Its Applications ADVANCED 2012 Surface Modeling Tutorial Introduction In this tutorial, you will create a toy race car body design using AutoCAD surface modeling techniques. The end result
More informationCHAPTER 6 THE SUITES VECTOR DRAWING SUITE
CHAPTER 6 THE SUITES There are two additional tool bar suites for Project Designer sold separately as add-on modules. These are the Vector Drawing Suite, and the Pattern Modeling Suite. This section will
More informationJewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3
Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in
More informationVERO UK TRAINING MATERIAL
VERO UK TRAINING MATERIAL VISI Basic 2-D Modelling course (V-16) VISI Modelling 2D Design Introduction Many component designs follow a similar route, beginning with a 2D design, part modelled using solids
More informationRhinoceros NURBS modeling for Windows. Version 1.0 Training Manual Level 1
Rhinoceros NURBS modeling for Windows Version 1.0 Training Manual Level 1 rhinolevel 1.doc Robert McNeel & Associates 1997. All Rights Reserved. Printed in U.S.A. Copyright by Robert McNeel & Associates.
More information7/21/2009. Chapters Learning Objectives. Fillet Tool
Chapters 12-13 JULY 21, 2009 Learning Objectives Chapter 12 Chapter 13 Use the FILLET tool to draw fillets, rounds, and other rounded corners. Place chamfers and angled corners with the CHAMFER tool. Separate
More informationAlibre Design Tutorial - Simple Revolve Translucent Glass Lamp Globe
Alibre Design Tutorial - Simple Revolve Translucent Glass Lamp Globe Part Tutorial Exercise 2: Globe-1 In this Exercise, We will set System Parameters first. Then, in sketch mode, we will first Outline
More information3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD
3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions
More informationSOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering
SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now
More informationBeginning Tutorial the Lego
Beginning Tutorial the Lego In this tutorial, you will construct a simple hollowed-out block with a hole in it (looks like a Lego). You will learn the basics of creating and modifying sketches and features.
More informationAssessment TESTS SLO #1 CADD 131
CADD 131 Assessment TESTS 1- SLO #1 1. Of what does a mesh model consist? 2. What is another term for mesh models? 3. What are tessellation divisions? 4. When creating a mesh primitive, when should mesh
More informationF1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
More information3D printing Workshop Breakdown
3D printing Workshop Breakdown Opening Lecture/Remarks (20-30 Minutes) -Introduction to 3D modeling software Overview of what 3D modeling software is Introduction to 123D Design Introduction to 123D Design
More informationIntroduction to AutoCAD 2010
Page 1 Introduction to AutoCAD 2010 Alf Yarwood Chapter 18 Exercise 1 1. Open AutoCAD 2010 with a double-click on its shortcut icon in the Windows desktop. 2. Open the template acadiso3d.dwt. 3. Make new
More informationLesson 14 Blends. For Resources go to > click on the Creo Parametric Book cover
Lesson 14 Blends Figure 14.1 Cap OBJECTIVES Create a Parallel Blend feature Use the Shell Tool Create a Swept Blend REFERENCES AND RESOURCES For Resources go to www.cad-resources.com > click on the Creo
More informationSolidworks 2006 Surface-modeling
Solidworks 2006 Surface-modeling (Tutorial 2-Mouse) Surface-modeling Solid-modeling A- 1 Assembly Design Design with a Master Model Surface-modeling Tutorial 2A Import 2D outline drawing into Solidworks2006
More information3. Preprocessing of ABAQUS/CAE
3.1 Create new model database 3. Preprocessing of ABAQUS/CAE A finite element analysis in ABAQUS/CAE starts from create new model database in the toolbar. Then save it with a name user defined. To build
More informationME 120: Impeller Model in Solidworks 1/6
ME 120: Impeller Model in Solidworks 1/6 Steps to Draw Pump Impeller: The steps below show one way to draw the impeller. You should make sure that your impeller is not larger than the one shown or it may
More informationGenerating Vectors Overview
Generating Vectors Overview Vectors are mathematically defined shapes consisting of a series of points (nodes), which are connected by lines, arcs or curves (spans) to form the overall shape. Vectors can
More informationChapter 12: Pull Toy - Solids and Transforms
This tutorial demonstrates using solid primitives and simple transforms. You will learn how to: Enter coordinates to place points exactly. Draw a free-form curve and polygon. Create a pipe along a curve.
More informationAutodesk Fusion 360: Model. Overview. Modeling techniques in Fusion 360
Overview Modeling techniques in Fusion 360 Modeling in Fusion 360 is quite a different experience from how you would model in conventional history-based CAD software. Some users have expressed that it
More informationChapter 4 Modeling Model View... 4
Chapter4 Modeling Model View 1 Chapter 4 Modeling Model View... 4 4.1 Base Tools... 4 4.1.1 Copy and Erase... 4 4.1.2 Undo and Redo... 4 4.1.3 Glue tools... 4 4.1.4 Group Tools... 5 4.1.5 Global and Interactive
More informationDoctor Walt s Solid Edge Version 19 Workbook 137
Still using the SMART DIMENSION Tool, click on the left vertical edge of the sketch. Move the cursor to the left and click to set the text position. Type 1.5 for the value and hit the ENTER Key. Next,
More informationMinimal AutoCAD 2011
PDHonline Course G371 (2 PDH) Minimal AutoCAD 2011 Instructor: Thomas Mason, P.E. 2012 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658 Phone & Fax: 703-988-0088 www.pdhonline.org
More informationBasic MicroStation Training Outline
12:30 DAY 1 Equipment Review Workstation, monitor, keyboard File server, Plot server, STATE server Drive Assignments Shortcut Menu General overview of commands Explorer Managing Folders & Files MicroStation
More informationCOMPUTER AIDED ARCHITECTURAL GRAPHICS FFD 201/Fall 2013 HAND OUT 1 : INTRODUCTION TO 3D
COMPUTER AIDED ARCHITECTURAL GRAPHICS FFD 201/Fall 2013 INSTRUCTORS E-MAIL ADDRESS OFFICE HOURS Özgür Genca ozgurgenca@gmail.com part time Tuba Doğu tubadogu@gmail.com part time Şebnem Yanç Demirkan sebnem.demirkan@gmail.com
More informationSpring 2011 Workshop ESSENTIALS OF 3D MODELING IN RHINOCEROS February 10 th 2011 S.R. Crown Hall Lower Core Computer Lab
[1] Open Rhinoceros. PART 1 INTRODUCTION [4] Click and hold on the Boundary Lines in where they form a crossing and Drag from TOP RIGHT to BOTTOM LEFT to enable only the PERSPECTIVE VIEW. [2] When the
More informationDecember 3, :30 to 5:30 pm. Speaker Name: Tom Short, P.E. Course Title: Taking A Step Into The World Of 3D
Las Vegas, Nevada December 3, 2002 1:30 to 5:30 pm Speaker Name: Tom Short, P.E. Course Title: Taking A Step Into The World Of 3D Course ID: GD122 Course Outline: Are you an experienced AutoCAD 2D user
More informationCATIA Surface Design
CATIA V5 Training Exercises CATIA Surface Design Version 5 Release 19 September 2008 EDU_CAT_EN_GS1_FX_V5R19 Table of Contents (1/2) Creating Wireframe Geometry: Recap Exercises 4 Creating Wireframe Geometry:
More informationIntroduction to SolidWorks for Technology. No1: Childs Toy
Introduction to SolidWorks for Technology No1: Childs Toy Table of Contents Table of Contents... 1 Introduction... 2 Part Modelling: Cab... 3 Part Modelling: Base... 6 Part Modelling: Wheel... 12 Assembly:
More informationAutodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
More informationStickFont Editor v1.01 User Manual. Copyright 2012 NCPlot Software LLC
StickFont Editor v1.01 User Manual Copyright 2012 NCPlot Software LLC StickFont Editor Manual Table of Contents Welcome... 1 Registering StickFont Editor... 3 Getting Started... 5 Getting Started...
More informationLesson 14 Blends. For Resources go to > click on the Creo Parametric 2.0 Book cover
Lesson 14 Blends Figure 14.1 Cap OBJECTIVES Create a Parallel Blend feature Use the Shell Tool Create a Hole Pattern REFERENCES AND RESOURCES For Resources go to www.cad-resources.com > click on the Creo
More informationequivalent stress to the yield stess.
Example 10.2-1 [Ansys Workbench/Thermal Stress and User Defined Result] A 50m long deck sitting on superstructures that sit on top of substructures is modeled by a box shape of size 20 x 5 x 50 m 3. It
More informationIntroduction to SolidWorks Basics Materials Tech. Wood
Introduction to SolidWorks Basics Materials Tech. Wood Table of Contents Table of Contents... 1 Book End... 2 Introduction... 2 Learning Intentions... 2 Modelling the Base... 3 Modelling the Front... 10
More informationModule 1: Basics of Solids Modeling with SolidWorks
Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists
More informationLesson 3: Surface Creation
Lesson 3: Surface Creation In this lesson, you will learn how to create surfaces from wireframes. Lesson Contents: Case Study: Surface Creation Design Intent Stages in the Process Choice of Surface Sweeping
More informationAdobe Illustrator CS5 Part 2: Vector Graphic Effects
CALIFORNIA STATE UNIVERSITY, LOS ANGELES INFORMATION TECHNOLOGY SERVICES Adobe Illustrator CS5 Part 2: Vector Graphic Effects Summer 2011, Version 1.0 Table of Contents Introduction...2 Downloading the
More informationModeling Technology Group
Modeling Technology Group Hiroshi Hayashi David Ogirala Matt Nedrich Jeff Ridenbaugh Spencer Smith Saba Bokhari John Gray Charles Hellstrom Bryan Linthicum Polygon Models (part-1) What are polygons? -
More information12 APPLYING EFFECTS. Lesson overview
12 APPLYING EFFECTS Lesson overview In this lesson, you ll learn how to do the following: Use various effects like Pathfinder, Distort & Transform, Offset Path, and Drop Shadow effects. Use Warp effects
More informationSOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users
SOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users The premium provider of learning products and solutions www.cadartifex.com Table of Contents Dedication... 3 Preface... 15 Part 1. Introducing
More informationTUTORIAL 07: RHINO STEREOTOMIC MODELING PART 2. By Jeremy L Roh, Professor of Digital Methods I UNC Charlotte s School of Architecture
TUTORIAL 07: RHINO STEREOTOMIC MODELING PART 2 By Jeremy L Roh, Professor of Digital Methods I UNC Charlotte s School of Architecture This tutorial will explore the Stereotomic Modeling Methods within
More informationFigure 1: NC > 2 Axis menu > Options
Click To See: How to Use Online Documents SURFCAM Online Documents J 685)&$0Ã5HIHUHQFHÃ0DQXDO 7 &21),*85$7,21722/6 7.1 INTRODUCTION SURFCAM s default configuration parameters are contained in the SURFCAM.INI
More informationRevit Architecture 2015 Basics
Revit Architecture 2015 Basics From the Ground Up Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit
More informationControl the Workplane
Control the Workplane This tutorial outlines the procedures to understand and control the user coordinate system (UCS). You can realign and reorient the UCS to create and modify 3D objects on 2D workplanes
More information3D AUTOCAD. The view we ve been working in is a top or plan view. From this view even a 3D drawing will appear 2D.
3D AUTOCAD Thus far, we ve looked at tools and operations in 2D with work completed on only the X- and Y- axes. The axes symbol has been present on our screen but we haven t had much use for it. The view
More informationThe Rectangular Problem
C h a p t e r 2 The Rectangular Problem In this chapter, you will cover the following to World Class standards: The tools for simple 2D Computer Aided Drafting (CAD) The Command Line and the Tray The Line
More informationRhino Interface. Menus Command History Command Prompt. Toolbars. Viewport Title. Viewports. Common Shortcuts. Object Snaps.
Rhino Interface Menus Command History Command Prompt Toolbars Viewport Title LMB: activate viewport without losing selection Double Click: maximise viewport RMB: show viewport options: wireframe, shaded,
More informationA pipe bend is subjected to a concentrated force as shown: y All dimensions in inches. Material is stainless steel.
Problem description A pipe bend is subjected to a concentrated force as shown: y 15 12 P 9 Displacement gauge Cross-section: 0.432 18 x 6.625 All dimensions in inches. Material is stainless steel. E =
More informationRhinoceros Car Modeling Tutorial
Rhinoceros Car Modeling Tutorial This tutorial will guide you to car nurbs modeling process using Rhinoceros 3.0. To start a car modeling you will need some car images (or sketches) to get an idea of the
More informationAGENDA: Using Gizmos to Modify 3D Models. AutoCAD 3 LECTURE NOTES: CLASS 08. Using Gizmos to Modify 3D Models
AGENDA: Using Gizmos to Modify 3D Models Using Gizmos to Modify 3D Sub-Objects and Faces 3DArray, Mirror3D, and Align Using Gizmos to Modify 3D Models Gizmos allow us to move, rotate, and scale a set of
More informationTutorial Second Level
AutoCAD 2018 Tutorial Second Level 3D Modeling Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn
More informationLesson 11. Polygonal Spaceship
11 Polygonal Spaceship In this lesson, you will build and texture map a polygonal spaceship. Starting with a polygonal cube, you will extrude facets until you have a completed ship. You will then be able
More informationCreating and Working with Solid Model Features
This sample chapter is for review purposes only. Copyright The Goodheart-Willcox Co., Inc. ll rights reserved. Chapter Creating and Working with Solid Model Features Learning Objectives fter completing
More informationCGS 3220 Lecture 17 Subdivision Surfaces
CGS 3220 Lecture 17 Subdivision Surfaces Introduction to Computer Aided Modeling Instructor: Brent Rossen Overview Converting from polygons to subdivision surfaces (sub-d) Modeling with sub-d using polygon
More informationRhinoceros. modeling tools for designers. Training Manual Level 1
Rhinoceros modeling tools for designers Training Manual Level 1 RH50-TM-L1-Sep-2013 Rhinoceros v5.0, Level 1, Training Manual Revised 9/30/2013, Mary Fugier mary@mcneel.com Q&A 9/30/2013,, Jerry Hambly
More informationChapter 1: Introduction
Modeling in 3-D is the process of creating a mathematical representation of an object's surfaces. The resulting model is displayed on your screen as a two-dimensional image. Rhino provides tools for creating,
More informationAutoCAD for Engineers and Designers, 21st Edition. (3D and Advanced)
AutoCAD 2015 for Engineers and Designers, 21st Edition (3D and Advanced) CADCIM Technologies 525 St. Andrews Drive Schererville, IN 46375, USA (www.cadcim.com) Contributing Author Sham Tickoo Professor
More information12 APPLYING EFFECTS. Lesson overview
12 APPLYING EFFECTS Lesson overview In this lesson, you ll learn how to do the following: Use various effects, such as Pathfinder, Scribble, and Drop Shadow. Use Warp effects to distort type. Create three-dimensional
More informationModule 6B: Creating Poly-Conic Sheet Metal Pieces for a Spherical Space
1 Module 6B: Creating Poly-Conic Sheet Metal Pieces for a Spherical Space In Module 6B, we will learn how to create a folded 3D model of an approximate 2D flat pattern for a 120-inch or 10-foot diameter
More informationTRAINING GUIDE WCS - VIEW MANAGER - PART-2
TRAINING GUIDE WCS - VIEW MANAGER - PART-2 Mastercam Training Guide Objectives The learner will create the geometry and toolpaths for WCS-Part-2. This Lesson will cover the following topics: Create a 3-dimensional
More informationArchitectural Trim & Moldings
Architectural Trim & Moldings Often, it s the subtle touches that make the biggest impact. With Stylmark s TrimMaker, you can easily add accent to walls, ceilings, soffits and columns to provide a smooth
More informationIf you have been using CorelDRAW, you may have turned off this opening screen. If so, skip to step 5.
Opening CorelDRAW If you have been using CorelDRAW, you may have turned off this opening screen. If so, skip to step 5. 1. When CorelDRAW is loaded, a new section is created on the Start Menu. To open
More information