Airplane Drawing. Chapter 10. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
|
|
- Cory Blake
- 5 years ago
- Views:
Transcription
1 Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse Step 4. Select your AIRPLANE ASSEMBLY file and click Open. Step 5. In the Property Manager under Orientation: click Right check Preview, Fig. 1 click Use custom scale and set scale to 1:1, Fig. 1. Step 6. Move the cursor into the graphic area and click to place the right side view as shown in Fig. 2. the right edge of the preview with the right border line and align wheel next to title block with the top of the title block. Step 7. Click OK Fig. 2 Fig. 1 B. Save as "AIRPLANE". Step 1. Click File Menu > Save As. Step 2. Key-in AIRPLANE for the filename and press ENTER. C. Insert Top View. Step 1. Click View Layout on the Command Manager toolbar and Model View on the View Layout toolbar. SolidWorks 12 DRAWING AIRPLANE Page 10-1 Cudacountry.net Tech Ed cudacountry@hotmail.com 2/17/12
2 Step 2. Click Next Step 3. In the Property Manager under Orientation: click Top. check Preview, Fig. 3 click Use custom scale and set scale to 1:1, Fig. 3. Step 4. Move the cursor into the graphic area and click to place the top view as shown in Fig. 4. the left edge of the wheel preview with the left border line and center fuselage between the top and bottom border lines. Step 5. Click Rotate View on the View toolbar. Fig. 4 Fig. 3 Step 6. Key-in 180 for the Drawing view angle and click Apply and Close, Fig. 5 and Fig. 6. Fig. 5 in the Property Man- Step 7. Click OK ager. Fig. 6 SolidWorks 12 DRAWING AIRPLANE Page 10-2
3 D. Hide Wing and H Stab. Step 1. Right click Wing that is outside drawing, click Show/ Hide from menu and click Hide Component, Fig. 7. Step 2. Right click H Stab that is outside drawing, click Show/ Hide from menu and click Hide Component, Fig. 8. Right click Wing Fig. 7 E. Insert Isometric View. Right click H Stab Step 1. Click View Layout on the Command Manager toolbar and Model View toolbar. Step 2. Click Next on the View Layout Fig. 8 Step 3. In the Property Manager, under Orientation: click Isometric check Preview click Use custom scale and set scale to 1:2, Fig. 9 Step 4. Move the cursor into the graphic area and click to place the isometric view as shown in Fig. 10. Step 5. Click OK in the Property Manager. Step 6. Save. Use Ctrl-S. Fig. 10 Fig. 9 SolidWorks 12 DRAWING AIRPLANE Page 10-3
4 F. Add Leaders and Notes to Stabilizers. Step 1. Click Annotation on the Command Manager toolbar. on the Annota- Step 2. Click Note tion toolbar. Step 3. In the Note Property Manger, under Leader: click Leader, Fig. 11 in top view, click the Leading Edge of the H Stab and bring the text box inside H Stab and click lock the Caps and key-in: LEADING EDGE, Fig. 12 click OK in Property Manager. Fig. 11 Fig. 12 on the Annota- Step 4. Click Note tion toolbar. Step 5. In the Note Property Manger, under Leader: Fig. 13 click NO Leader (red X), Fig. 13 click inside H Stab and key-in H STAB MAKE 2, Fig. 14 click OK in Property Manager. Fig. 14 Step 6. Click Note Step 7. In the Note Property Manger, under Leader: click Leader, Fig. 11 click the leading edge of the V Stab and bring the text box inside V Stab and click lock the Caps and key-in LEADING EDGE, Fig. 15 click OK in Property Manager. Fig. 15 SolidWorks 12 DRAWING AIRPLANE Page 10-4
5 Step 8. Click Note Step 9. In the Note Property Manger, under Leader: click NO Leader (red X) click inside V Stab and key-in V STAB, Fig. 16 click OK in Property Manager. G. Add Your Name and Period to Title Block. Step 1. Use the Zoom to Area in the View toolbar to drag a zoom window around the DRAWN BY and PE- RIOD in the title block, Fig. 17. Fig. 16 Step 2. Click Note toolbar. on the Annotation Step 3. Click just to the right of DRAWN BY:, Fig. 18. Step 4. Lock the Caps and key-in your first and last names, Fig. 18. Fig. 17 Zoom Step 5. Click OK in the Property Manager. Fig. 18 Step 6. Click Note Step 7. Click just to the right of PERIOD: and key-in your Period number, Fig. 19. Step 8. Click OK in the Property Manager. Fig. 19 Step 9. Save. Use Ctrl-S. SolidWorks 12 DRAWING AIRPLANE Page 10-5
Drawing. Chapter 10. Airplane. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager.
More informationBottle Rocket. Drawing. on the Com- on the View Layout
Chapter 6 Bottle Rocket Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing Metric and OK. on the Com- Step 2. Click View Layout mand Manager toolbar. Step 3. Click Model View toolbar.
More informationDrawing. Chapter 12. Beam. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View. on the View Layout toolbar.
Chapter 12 Beam Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationChapter 11 Solar Car Drawing
Chapter 11 Solar Car Drawing A. Insert Top and Side Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Browse Step 3. Select your solar car assembly file and click Open. Step 4.
More informationAirplane Assembly. SolidWorks 10 ASSEMBLY AIRPLANE Page 9-1
Chapter 9 A. Insert Parts. Airplane Assembly Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the Property Manager,
More informationDrawing. Chapter 11. Bridge. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. on the View Layout toolbar.
Chapter 11 Bridge Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationFig. 1. Fig. 1. on the Standard Views toolbar. SolidWorks ASSEMBLY AIRPLANE Page 8-1
Chapter 8 Airplane Assembly A. Insert Set of Parts. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click View Menu > Origins to display the origin. Step 3. Click Keep Visible in the Property
More informationTail Hook. Chapter 14. Airplane. A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK.
Chapter 14 Airplane Tail Hook A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right (plane) in the Feature Manager and click Sketch from the Content toolbar,
More informationPhotoView 360 Decals
Chapter 10 Glider PhotoView 360 Decals A. Enable PhotoView 360. Step 1. If necessary, open your GLIDER ASSEMBLY file. Step 2. If necessary, turn on PhotoView 360. Click Tools Menu > Add- Ins. Click to
More informationFlow Sim. Chapter 16. Airplane. A. Add-In. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 A. Add-In. Step 1. If necessary, open your ASSEMBLY file. Airplane Flow Sim Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in
More informationPanel. Chapter 16. Solar Car. A. Sketch. Step 1. Click File Menu > New, click Part and OK. B. Save as "PANEL". Step 1. Click File Menu > Save As.
Chapter 16 Solar Car Panel A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Center
More informationAirplane. Chapter 21. Mastercam A. Create Rectangle. B. Save As AIRPLANE. C. Set Grid and Snap.2. Mastercam 2017 Airplane Page 21-1
Mastercam 2017 Chapter 21 A. Create Rectangle. Airplane Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step 2. On the Wireframe tab click Rectangle.
More informationFuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
More informationCO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.
Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationFlow Sim. Chapter 14 P-51. A. Set Up. B. Create Flow Simulation Project. Step 1. Click Flow Simulation. SolidWorks 10 Flow Sim P-51 Page 14-1
Chapter 14 A. Set Up. P-51 Flow Sim Step 1. If necessary, open your ASSEMBLY file. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in the
More informationH Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.
Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch
More informationClay. Chapter 9. Glider. A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. C. Sketch. Step 1. Click the side face of the
More informationBoat. Hull. Step 4. Sketch point directly above the Origin, Fig. 2. Use the inferencing line, the dotted line that appears when you sketch the point.
Chapter 1 Boat Hull A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step 3. Click Point on
More informationFlow Sim. Chapter 16. Airplane. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 Airplane Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar
More informationFlow Sim. Chapter 12. F1 Car. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 12 F1 Car Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar and
More informationCO2 Car Assembly. in the Property Manager to place the part at the origin, Fig. 1. on the Assemblies toolbar. SolidWorks Assembly CO2 CAR Page 8-1
Chapter 8 CO2 Car Assembly A. Insert Axles and Wheels. Step 1. Click File Menu > New, click Assembly Metric and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the
More informationGlider. Clay. Fig. 1 Side face. Step 5. In the Convert Entities Property Manager: click side face, Fig. 3 click OK twice, Fig. 3. Fig. 3.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. Step 2. Click the side face of the Fuselage,
More informationChair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.
Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,
More informationWheels and Axle. Chapter 7. Simples Machines. A. Save As. Step 1. If necessary, open your Track Assembly 15 file. B. Insert Truck Assembly.
Chapter 7 Simples Machines Wheels and Axle A. Save As. Step 1. If necessary, open your Track Assembly 15 file. Step 2. Click File Menu > Save As. Step 3. Key-in WHEELS AND AXLE ASSEMBLY for the filename
More informationAssembly Motion Study
Penny Hockey Chapter 10 Assembly Motion Study A. Rename Penny Mate. Step 1. Open your PENNY HOCKEY ASSEMBLY file. Step 2. Expand Mates in the Feature Manager and select the last Mate, Fig. 1. This should
More informationNose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1
Chapter 4 Rocket 3D Print Nose Cone A. Revolve. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step
More informationWheel GT-F. Chapter 5. CO2 Shell Car. A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK.
Chapter 5 CO2 Shell Car Wheel GT-F A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1.
More informationDelta IV Heavy. Interstage. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Command Man- on the Features
Chapter 4 Delta IV Heavy Interstage A. Sketch Circles. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationBody. Chapter 2. CO2 Rail Car E. A. Save as "BODY RAIL E". Step 1. Open your BLANK file.
Chapter 2 A. Save as "BODY RAIL E". Step 1. Open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY RAIL E for the filename and press ENTER. CO2 Rail Car E Body B. Appearance. Step
More informationSpring Assembly. in the Begin Assembly Property. on the Standard toolbar and click Add-Ins.
Chapter 2 Spring Assembly A. Create New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Cancel Manager. in the Begin Assembly Property B. Enable Toolbox Browser. Step 1. If
More informationSolar Car. Chassis. in the Feature Manager and click Sketch from the Content toolbar, Fig. 2. Origin. on the Command Manager toolbar. Fig.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Solar Car Chassis Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Chassis. Step 1. Click Right Plane in the Feature Manager and click
More informationCO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.
CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.
More informationGlider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.
Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.
More informationRocket 1. Fin. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig. 1. Fig. 2
Chapter 2 Rocket 1 Fin A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Line
More informationBlank. Chapter 1. CO2 Rail Car. A. New Metric Part. Step 1. Click File Menu > New. B. Body. Step 1. Click Right Plane
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. CO2 Rail Car Blank Step 2. Click Part Metric from the list and click OK, Fig. 1. If you are not using SolidWorks templates (you should be),
More informationBody. Chapter 1. Simple Machines. A. New Part. Step 1. Click File Menu > New.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Simple Machines Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.
More informationSimple Machines. Wheel. in the Feature Manager and click Sketch. on the Command Manager toolbar.
Chapter 3 Simple Machines Wheel A. Wheel. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step 3. Click
More informationSkateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
More informationPropeller. Chapter 13. Airplane. A. Base for Blade. Step 1. Click File Menu > New, click Part and OK.
Chapter 13 Airplane Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch toolbar, Fig. 1. from the Content Step
More informationExport DXF to CorelDRAW
Chapter 13 Glider Export DXF to CorelDRAW A. Export Fuselage/Tooth Sketch as DXF". Step 1. Open your FUSELAGE part file. Step 2. Roll the rollback bar to below the Cut-Extrude1. To rollback, click Fillet1
More informationDelta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.
Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step
More informationF-1 Car. Blank. in the Feature Manager and click Sketch from the Content toolbar, Fig. 3. Origin. on the Features toolbar.
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. F-1 Car Blank Step 2. Click Part Metric from the list of templates and click OK, Fig. 1. If you are not using SOLIDWORKS templates (you should
More informationDelta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationSkateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationBattery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
More informationExport DXF to Illustrator
Chapter 12 Glider Export DXF to Illustrator A. Export Fuselage/Tooth Sketch as DXF". Step 1. Open your FUSELAGE part file. Step 2. Roll the rollback bar to below the Cut-Extrude1. To rollback, click Fillet1
More informationTerminal. Chapter 16. E-Car. A. Component from Design Library. SOLIDWORKS 17 Terminal E-CAR Page 16-1
Chapter 16 E-Car Terminal A. Component from Design Library. Step 1. Click the Design Library tab in the Task Pane (right side of graphics area), Fig. 1. Step 2. Expand routing and click electrical folder
More informationSpeedway. Motion Study. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click Tools Menu > Add-Ins.
Chapter 8 Speedway Motion Study A. Enable SolidWorks Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click
More informationSpeedway. Motion Study. on the Standard toolbar and click Add-Ins. at the lower
Chapter 8 Speedway Motion Study A. Enable SOLIDWORKS Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, enable Motion, click the flyout of Options on the Standard toolbar
More informationSpeedway. Body. (S) on the Sketch toolbar. Fig. 1
Chapter 1 A. New Part. Step 1. Click File Menu > New. Speedway Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature Manager
More informationJSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar.
Chapter 18 JSS Ping Pong Ball A. Half Circle Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig.
More informationBattery Holder 2 x AA
Chapter 22 JSS Battery Holder 2 x AA A. Front Extrude. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Context toolbar,
More informationF1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
More informationCO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 21 CO2 Shell Car Mastercam X6 for SolidWorks Toolpaths A. Enable Mastercam for SolidWorks. Step 1. If necessary, turn on Mastercam for SolidWorks, click Tools Menu > Add-Ins. Step 2. In the dialog
More informationSimple Machines. Body. Step 4. Start at Origin and sketch the 8 lines, Fig. 2. Fig. 1. Origin
Chapter 1 Simple Machines Body A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1. Step 3. Click
More informationPenny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam Step 1. If necessary, save your BASE file in SOLIDWORKS.
Mastercam 2017 Chapter 22 Chapter 7 Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam 2017. Step 1. If necessary, save your BASE file in SOLIDWORKS. Step 2. In Mastercam 2017, click
More informationBoat. Battery Holder AA
Chapter 9 Boat Battery Holder AA A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch context toolbar, Fig. 1. Step 3. Click
More informationAirplane Propeller. Click Show All from the Zoom Control at the right end of the Timeline.
Flash Chapter 10 A. Open your "airplane path" file. Step 1. Open your airplane path file. B. Move Propeller Off Fuselage. Airplane Propeller Step 1. Click Edit Symbols Button at the right end of the Timeline,
More informationCudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1
Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click
More informationBoat Hull Solid. (Alt-2). in ribbon bar to fix and close ribbon Fig. 3 Mastercam X7 BOAT HULL SOLID Page 29-1
Mastercam X7 Chapter 29 A. Open Boat Block File. Step 1. Open your BOAT BLOCK file. Boat Hull Solid B. Save As BOAT HULL SOLID Step 1. Click File Menu > Save As. Step 2. Key-in BOAT HULL SOLID for the
More informationToolpaths for Fuselage
Mastercam 2017 Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Hide Top Surface. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. On the Home tab click Hide/Unhide
More informationBottom Truss ANALYSIS
Chapter 3 Beam Bottom Truss ANALYSIS A. Enable SolidWorks Simulation. Step 1. If necessary, open your Beam1 part file. Step 2. If necessary, turn on SolidWorks Simulation. To turn on Solid- Works Simulation,
More informationCatamaran A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click File Menu > New.
Mastercam X7 Chapter 26 Catamaran A. Create Rectangle. Step. If necessary start a new Mastercam file, click File Menu > New. Step 2. Click Create Menu > Rectangle or click Rectangle Tool Step 3. In the
More informationMastercam X9 for SOLIDWORKS
Chapter 21 CO2 Shell Car Mastercam X9 for SOLIDWORKS A. Enable Mastercam for SOLIDWORKS. Step 1. If necessary, turn on Mastercam for SOLIDWORKS, click the flyout of Options on the Standard toolbar and
More informationCatamaran A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N).
Mastercam 07 Chapter 6 Catamaran A. Create Rectangle. Step. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step. On the Wireframe tab click Rectangle. Step
More informationSolidWorks 2015 User Interface
SolidWorks 2015 User Interface SolidWorks a Dassault Systèmes Product Starting SolidWorks 1) On the desktop, double-click or from the start menu select: All Programs SOLIDWORKS 2015 SOLIDWORKS 2015. 2)
More informationBelt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.
More informationChapter 36. Mastercam Jewelry Box Fixture. A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 36 Jewelry Box Fixture A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe
More informationExercise 1. Section 2. Working in Capture
Exercise 1 Section 1. Introduction In this exercise, a simple circuit will be drawn in OrCAD Capture and a netlist file will be generated. Then the netlist file will be read into OrCAD Layout. In Layout,
More informationIntroduction to SolidWorks for Technology. No1: Childs Toy
Introduction to SolidWorks for Technology No1: Childs Toy Table of Contents Table of Contents... 1 Introduction... 2 Part Modelling: Cab... 3 Part Modelling: Base... 6 Part Modelling: Wheel... 12 Assembly:
More informationFig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1
Mastercam 2020 Chapter 13 Spinning Top SOLIDWORKS 19 to Mastercam 2020 A. Open File in Mastercam 2020. Step 1. If necessary, save your Handle and Flywheel parts file in SOLIDWORKS. Step 2. In Mastercam
More informationIn so many ways summary
In so many ways summary Many of Word s functions can be activated in a variety of different ways. Often you can use the menu, a tool on the toolbar or a shortcut key to achieve the same result. Rather
More informationChapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks.
Chapter 3 CO2 Car SolidWorks to Mastercam X 2007 A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box scroll
More informationReset Cursor Tool Clicking on the Reset Cursor tool will clear all map and tool selections and allow tooltips to be displayed.
SMS Featured Icons: Mapping Toolbar This document includes a brief description of some of the most commonly used tools in the SMS Desktop Software map window toolbar as well as shows you the toolbar shortcuts
More informationChapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1
Mastercam 2017 Chapter 39 A. Sketch Tray Circle. Jewelry Box Tray Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click
More informationSOLIDWORKS: Lesson 1 - Basics and Modeling. Introduction to Robotics
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals Introduction to Robotics SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment
More informationAutodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
More informationJewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3
Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in
More informationProject 3. Top Down Design In Context. Below are the desired outcomes and usage competencies based upon the completion of this Project.
Assembly Modeling with SolidWorks Project 3 Below are the desired outcomes and usage competencies based upon the completion of this Project. Project Desired Outcomes: 2AXIS-TRANSFER Assembly. PLATE-B Part.
More informationTUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs.
TUTORIAL 2 OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. GETTING STARTED: 1. Open the SolidWorks program. 2. Open a new part file.
More informationSolidWorks Import Tutorial
SolidWorks Import Tutorial Current Item: SolidWorks Import Tutorial Before You Begin This tutorial will step you through the process of exporting a file from SolidWorks and importing it into Bend-Tech.
More informationVision Pointer Tools
Vision Pointer Tools Pointer Tools - Uses Pointer Tools can be used in a variety of ways: during a Vision Demo to annotate on the master station s screen during a Remote Control session to annotate on
More informationDrum Kit A. Setup to Trace Bitmap. Step 1. Click Window Menu > Other Panels > Common Libraries > Drumkit.
Flash Chapter 20 Drum Kit A. Setup to Trace Bitmap. Step 1. Click Window Menu > Other Panels > Common Libraries > Drumkit. Find drum kit.jpg in the list of symbols in the Library Window. Drag the file
More informationMicrosoft Word Training
Microsoft Word Training Objectives: Become familiar with the Word Window, toolbars, and menus Learn to Save and Print Learn how to create tables, forms and templates Opening Word / Menus / Toolbars Click
More informationV-BOX Cloud Configuration
V-BOX Cloud Configuration Website: http://www.we-con.com.cn/en Technical Support: support@we-con.com.cn Skype: fcwkkj Phone: 86-591-87868869 QQ: 1043098682 Technical forum: http://wecon.freeforums.net/
More informationCreate a 3D Printing Project. New Project-set part on Tray 13,0600,1489,1616(SP6)
Create a 3D Printing Project New Project-set part on Tray 13,0600,1489,1616(SP6) In this exercise, we will learn to create New Project-set part on Tray. To create a new project and set the tray we need
More informationExercise 2a: Load, Animate and Review a Model
Exercise 2a: Load, Animate and Review a Model This exercise uses the file bumper_deck.key and the corresponding d3plot. Step 1: Load the solver input and result files, bumper_deck.key and d3plot. 1. From
More informationSOLIDWORKS 2017 Keyboard Modifiers & Shortcuts
SOLIDWORKS 2017 Keyboard Modifiers & Shortcuts Copy/Paste Ctrl+C and Ctrl+V These are similar in functionality to Windows. Sketches Copies and pastes sketch entities. Part Copies and pastes sketches. Assemblies
More informationPrezi Creating a Prezi
Prezi Creating a Prezi Log in to your account and click on the New Prezi button. Enter a title and (optional) description, and then click on the Create New Prezi button. Selecting a Template Select a template.
More informationChanges from SolidWorks 2003 to SolidWorks 2004
Changes from SolidWorks 2003 to SolidWorks 2004 The changes from SolidWorks 2003 to SolidWorks 2004 are primarily cosmetic. Consequently, it is quite easy to use the current edition of Learning SolidWorks
More informationWorking with PhotoVCarve files
Getting Started with Tutorial 4 Intermediate Level Working with PhotoVCarve files VCarve Pro Disclaimer All CNC machines (routing, engraving, and milling) are potentially dangerous and because Vectric
More informationDrawing Tips ME170. Instructor: Mike Philpott (
Drawing Tips Instructor: Mike Philpott (email: mphilpot@illinois.edu) Configuration of Creo Prepare Creo for drawing creation. - Open Creo Parametric 3.0 from the Start Menu. - Set your working directory.
More informationChapter 1: Quick Start
This chapter gives the steps for reconstructing serial sections. You will learn the basics of using RECONSTRUCT TM to import a series of images, view and align the sections, trace profiles, and generate
More informationME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.
PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step
More informationMicrosoft Visio 2010: An Introduction
Microsoft Visio 2010: An Introduction This document provides an introduction to using Microsoft Visio 2010. Microsoft Visio is software designed to translate complex information from text and tables into
More informationCreating a Title Block & Border Using Chief Architect. Architectural Design & Residential Construction Penncrest High School
Creating a Title Block & Border Using Chief Architect Architectural Design & Residential Construction Penncrest High School 2017-2018 Select New Layout to begin designing your Title Block. Note: Once the
More informationExtrusion Revolve. ENGR 1182 SolidWorks 02
Extrusion Revolve ENGR 1182 SolidWorks 02 Today s Objectives Creating 3D Shapes from 2D sketches using: Extrusion Revolve SW02 In-Class Activity Extrude a Camera Revolve a Wheel SW02 Out-of-Class Homework
More informationWord 2010 Beginning. Technology Integration Center
Word 2010 Beginning File Tab... 2 Quick Access Toolbar... 2 The Ribbon... 3 Help... 3 Opening a Document... 3 Documents from Older Versions... 4 Document Views... 4 Navigating the Document... 5 Moving
More information