Reference Manual (Hardware)

Transcription

1 CONPROSYS nano Remote I/O CPU Unit CPSN-MCB271-S1-041 Reference Manual (Hardware) CONTEC CO., LTD.

2 Check Your Package Thank you for purchasing the CONTEC product. This product consists of the items listed below. Check, with the following list, that your package is complete. If you discover damaged or missing items, contact your retailer. Product Configuration List - Product [CPSN-MCB271-S1-041] 1 - Product Guide 1 - Warranty Certificate 1 - Serial Number Label 1 - Power Connector 1 - Blank panel 3 Product Product Guide Warranty Certificate Serial Number Label Power Connector (attached to the product) Blank panel (attached to the product) *This product is verified in conformity with our recommended power supply. In case you use other power supplies, thus, it may not be able to fulfil certification requirements. Please see the Contec website regarding power supply recommendation. CPSN-MCB271-S1-041 Reference Manual (Hardware) i

3 Copyright Copyright 2018 CONTEC CO., LTD. ALL RIGHTS RESERVED. No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this document. The information in this document is subject to change without notice. All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD. Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear in this document or for results obtained by the user as a result of using this product. Trademarks This product is a registered trademark or trademark of CONTEC CO., LTD. Other company and product names that are referred to in this manual are generally trademarks or registered trade trademark. ii CPSN-MCB271-S1-041 Reference Manual (Hardware)

4 Table of Contents Check Your Package... i Copyright... ii Trademarks... ii Table of Contents... iii 1. Before Using the Product 1 About the Unit... 1 Hardware Features... 1 Software Features... 2 How to use... 2 Model details... 3 Customer Support... 4 Limited Two-Year Warranty... 4 How to Obtain Service... 4 Liability... 4 Safety Precautions... 5 Safety Information... 5 Handling Precautions Setup 9 Setup Procedure... 9 Installation Mounting on and Removing from the DIN Rail or the wall Installation Conditions Installation and Removal of I/O module and blank panels Inserting and Removing the microsd Cable Connection Cable Connection Power LAN RS-232C (COM) Software Setup Nomenclature and Functions 29 Nomenclature of Components Component Functions Power Connector (12-24VDC) LED RS-232C Interface (COM) CPSN-MCB271-S1-041 Reference Manual (Hardware) iii

5 Push Switch (SW) USB Port (USB) LAN Port (LAN) Expansion slot microsd Card Slot System Reference 37 Specifications Power Requirements Physical Dimensions List of Optional Products 41 DIN rail fitting power supply I/O module iv CPSN-MCB271-S1-041 Reference Manual (Hardware)

6 1 Before Using the Product 1. Before Using the Product This chapter provides necessary information before using the product. About the Unit This product is a remote I/O model CPU unit that has RS-232C and LAN interfaces in addition to four expansion slots. If necessary, you can freely combine this product with CONPROSYS nano series I/O modules. In addition, this product can be controlled from a PC running Windows or Linux and supports Modbus TCP Slave and Modbus RTU Slave. Hardware Features I/O module expansion With this product, you can freely add I/O modules to match the necessary functions from among the varied collection of CONPROSYS nano series I/O modules. Max. 921,600bps RS-232C Serial Communication The Product has one RS-232C-standard serial port. Baud rates from 110 to 921,600 bps can be set. Compact Design Compact design, 110 (W) 74.8 (D) 95 (H) mm, features flexibility in installation. Easy installation and removal of I/O modules Expansion modules can be installed and removed without any tools. Adaptable to a wide range of temperature between -20 and +60 C The product is capable of operating in the temperature between -20 and + 60 C. It can be installed in the various environments. Installation easy with a two-piece terminal on DIN or with screws Regarding the power connector, the terminal connector can be removed without a screwdriver. Even when a malfunction occurs, this product can be replaced in a short length of time. Furthermore, as the product is mounted on the DIN rail, removing and replacing are easy as well. This product can also be installed with screws, so it supports a wide range of installation situations. Equipped with the LED for an operation check The product has the LED for an operation check, which helps you visually confirm the communication status of each interface. No electrolytic capacitor The product has the LED for an operation check, which helps you visually confirm the communication status of each interface. CPSN-MCB271-S1-041 Reference Manual (Hardware) 1

7 1 Before Using the Product Software Features Compatible with Modbus TCP Slave and Modbus RTU Slave Modbus is a communication protocol widely adopted in the industrial sector. Controlling and collecting data from higher-level devices with Modbus Master function can be conducted. Applicable with Windows driver software The product supplies UDP/IP-based original protocol (F&eIT) and applications can be created with Windows driver software in the Win32 API function format (DLL). On top of that, you can check whether software and hardware are operating properly with the diagnostic program. Support the virtual COM driver Software virtual COM driver enables you to operate the product in the same way as PC COM port (standard COM). Applications can be created with the OS standard Win32 API communication function. How to use Information regarding how to use this product is given in the CPSN-MCB271 Reference Manual (Software), so check the System Setup Guide from the CONTEC website. The name of the documents Contents How to get Product Guide Reference Manual for I/O Module (Hardware) Reference Manual for CPU Unit (Hardware) Reference Manual for CPU Unit (Software) This guide explains how to check the items included with the product and the precautions before using the product. The warranty is included with this guide, so store it in a safe place. This manual explains items pertaining to the hardware such as the I/O module's functions and settings. This manual explains items pertaining to the hardware such as the CPU unit's functions and settings. This manual explains the settings of "CONPROSYS nano WEB Setting". Come with the document. (Printed matter) Download (PDF) Download (PDF) Download (PDF) Download 2 CPSN-MCB271-S1-041 Reference Manual (Hardware)

8 1 Before Using the Product Model details CPSN - MCB S CONPROSYS nano Series No Item Contents 1 Model MCB: Standard Backplane Model 2 CPU 2: ARM Cortex M3 3 Memory 7: 16M Byte 4 Version 1: The 1 st Model 5 Interface S: Serial (RS-232C/RS-422/485) 6 Numbering of the Interface 1: The 1 st Model 7 OS 0: Non OS 8 ROM 4:4MB 9 Application 1: Original version CPSN-MCB271-S1-041 Reference Manual (Hardware) 3

9 1 Before Using the Product Customer Support CONTEC provides the following support services for you to use CONTEC products more efficiently and comfortably. Web Site Latest product information CONTEC provides up-to-date information on products. CONTEC also provides product manuals and various technical documents in the PDF. Free download You can download updated driver software and differential files as well as sample programs in several languages. Note: For product information Contact your retailer if you have any technical questions regarding a CONTEC product or need its price, delivery time, or estimate information. Limited Two-Year Warranty CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and workmanship for up to two years from the date of purchase by the original purchaser. Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from which it was purchased. This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and original products. The warranty is not applicable if the device has been tampered with or damaged through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in which case repairs will be considered beyond the warranty policy. How to Obtain Service For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you purchased before returning any product. * No product will be accepted by CONTEC group without the RMA number. Liability The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage, misuse, or malfunction of this device. 4 CPSN-MCB271-S1-041 Reference Manual (Hardware)

10 1 Before Using the Product Safety Precautions Understand the following definitions and precautions to use the product safely. Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment safely. DANGER WARNING CAUTION DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or in property damage. CPSN-MCB271-S1-041 Reference Manual (Hardware) 5

11 1 Before Using the Product Handling Precautions DANGER - Do not use the product in locations exposed to a flammable or corrosive gas. It may cause explosion, fire, electrical shock, or malfunction. - Do not allow the device to come into contact with foreign substances (metal particles, flammable substances, liquids, etc.) Otherwise, it can cause fire or electrical shock. - Do not place the product in an unstable location or use incomplete mountings. Otherwise, it may cause the device to fall. - Be sure to connect the product to the stipulated power supply voltage. Connecting to a different voltage might cause a fire or electrical shock. - If the product is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. - The product is not intended for use in aerospace, space, nuclear power, medical equipment, or other applications that require a very high level of reliability. Do not use the product in such applications. - If using the product in applications where safety is critical such as in railways, automotive, or disaster prevention or security systems, please contact your retailer. CAUTION - Be certain the following requirements are satisfied when using the product. - Indoor use - Altitude up to 5000m - Applicable POLLUTION DEGREE 2 When using the product at high altitudes, refer to the relational expression below to find an appropriate ambient temperature. The heat dissipation decreases due to air pressure drop and could lead to damages or a shorter product life. - Ambient temperature = 60[ C] x altitude [m] An Example) The product is used at 3000 meters 60 C - (0.005 x 3000m) = 45 C (Ambient temperature) - Do not use or store the product in a location exposed to extremely high or low temperature that exceeds range of specification or susceptible to rapid temperature changes. e.g. - Exposure to direct sun - In the vicinity of a heat source - Do not use the product in extremely humid or dusty locations. It is extremely dangerous to use the product with its interior penetrated by water or any other fluid or conductive dust. If the product must be used in such an environment, install it on a dust-proof control panel, for example. - Avoid using or storing the product in locations subject to shock or vibration that exceeds range of specification. - When transporting the product, take suitable measures to avoid applying shock or vibration directly to the product. Impact resistance: 15G (11ms) below. - Use the product in the specified operating condition (temperature, humidity, vibration and shock). 6 CPSN-MCB271-S1-041 Reference Manual (Hardware)

12 1 Before Using the Product - Avoid installing in the place where ventilation of the product may compromise. Insufficient aeration could heat up the product and lead to malfunctions or damages. - Do not use the product in the vicinity of devices that generate strong magnetic force or noise. Such products will cause the product to malfunction (stop, reboot). - Do not use or store the product in the presence of chemicals. - When removing connectors or cables, always unplug the power cable of CPU unit and confirm the LEDs are turned off. - Do not modify the product. CONTEC will bear no responsibility for any problems, etc., resulting from modifying the product. - In the event of failure or abnormality (foul smells or excessive heat generation), unplug the power cable of CPU unit immediately and contact your retailer. - When using the product in an overly noisy environment, use a grounded, shielded cable to connect with peripherals. - To clean the product, wipe it gently with a soft cloth dampened with either water or mild detergent. Do not use chemicals or a volatile solvent, such as benzene or thinner, to prevent the paint to be scraped or discolored. - When connecting cables, first check the shapes of connectors, and then insert them in the correct orientation. After they are connected, do not put too much load on the connected part. Doing so may result in poor contact or damage to the product and the connected part. - Do not touch metal parts or terminals with your hands when the product is in operation. Otherwise, the product may malfunction, or cause failure. - Do not touch the front panels with your hands when the product is in operation. Otherwise, the product may malfunction or cause failure. - Do not touch the product or connectors with a wet hand to avoid electric shock. - The specifications of the product are subject to change without notice for enhancement and quality improvement. Even when using the product continuously, be sure to read the manual in the CONTEC s website and understand the contents. - When the product is used in a place that is affected by overcurrent or overvoltage (lightning surge), select appropriate surge protection device for all of the route (Signal line, etc.). Consult with the specialist regarding selecting, purchasing, and setting the surge protection device. - The product is an open-type device (a device designed to be housed inside other equipment) and must always be mounted inside a mechanical enclosure having enough strength. - Do not strike or bend this product. Otherwise, this product may malfunction, overheat, cause a failure or breakage. - Do not touch this product's metal plated terminals (edge connector) with your hands. Otherwise, this product may malfunction, overheat, or cause a failure. If the terminals are touched by someone's hands, clean the terminals with industrial alcohol. - Always install the blank panels into vacant slots while power is active. - Regarding CE EMC Directive Notice. Please connect the Interface Connector with a shielded cable to meet the mentioned standard above. CPSN-MCB271-S1-041 Reference Manual (Hardware) 7

13 1 Before Using the Product - When disposing of the product, follow the disposal procedures stipulated under the relevant laws and municipal ordinances. - Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever (Including damages for loss of business profits) arising out of the use or inability to use this CONTEC product or the information contained herein. FCC PART15 Class A Notice NOTE This equipment has been tested and found to comply with the limits for a ClassA digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. EN55032 Class A Notice Warning: Operation of this equipment in a residential environment could cause radio interference. Display of power (Input Rating Label) DC power supply Functional earth terminal Functional earth terminal 8 CPSN-MCB271-S1-041 Reference Manual (Hardware)

14 2 Setup 2. Setup Setup Procedure Follow the steps below to set up. STEP1 Installation procedure Proceed accordingly with the instruction to set up the product correctly. STEP2 Cable connection STEP3 Turning on the power. Reconfirm that you have correctly followed steps 1and 2. Then, turn on the power. If you find any errors or abnormalities after turning on the power, turn it off immediately and check whether the setup has been properly conducted. CPSN-MCB271-S1-041 Reference Manual (Hardware) 9

15 2 Setup Installation Mounting on and Removing from the DIN Rail or the wall Before mounting the product on the DIN rail, you need to unlock the fixed hook of the product. If you plan to mount the product on the wall, appropriate commercial screws are necessary. Unlock a fixed hook (1) Insert a slotted screwdriver (the point should be smaller than 7mm) into a hole. (see the figure below) Projection Tip Screwdriver insertion hole DIN rail fixed hook Figure 2.1. Unlocking the fixed hook < 1 / 3 > Figure 2.2. Unlocking the fixed hook < 2 / 3 > (2) By using the screwdriver as leverage, move it upward in the direction of the arrow to unlock. 10 CPSN-MCB271-S1-041 Reference Manual (Hardware)

16 2 Setup Figure 2.3. Unlocking the fixed hook < 3 / 3 > CPSN-MCB271-S1-041 Reference Manual (Hardware) 11

17 2 Setup Mount on the DIN Rail (1) Pull down the fixed hook at the bottom to unlock. Figure2.4. Mounting on the DIN Rail < 1 / 3 > (2) Hang the product on the upper part of the DIN rail, and press it to the lower side of the DIN rail. Figure2.5. Mounting on the DIN Rail < 2 / 3 > 12 CPSN-MCB271-S1-041 Reference Manual (Hardware)

18 2 Setup (3) Push up the hook to lock. Figure2.6. Mounting on the DIN Rail < 3 / 3 > CAUTION Confirm whether the product has been securely mounted onto the DIN rail. CPSN-MCB271-S1-041 Reference Manual (Hardware) 13

19 2 Setup Remove from the DIN Rail (1) Pull down the fixed hook at the bottom to unlock. Figure 2.7. Removing from the DIN Rail < 1 / 2 > (2) Pull the lower part of the product toward you and lift it up. e Figure 2.8. Removing from the DIN Rail < 2 / 2 > 14 CPSN-MCB271-S1-041 Reference Manual (Hardware)

20 2 Setup Mounting on the wall (1) Use the three M3 screws to mount the product on the wall. (2) The tightening torque should be within 6 kgf cm. The excessive torque could damage the product. (3) When using the helical spring lock washers, use the ones with the diameter smaller than 8mm. Figure 2.9. Mounting on the wall CAUTION Confirm whether the product has been securely mounted onto the wall. CPSN-MCB271-S1-041 Reference Manual (Hardware) 15

21 PWR RUN STS ERR SW V- LINK/AC T SPEED V+ 2 Setup Installation Conditions Installation orientation You can position the product in the orientation shown below. Other orientations could cause problems such as malfunction due to inadequate heat dissipation. Vertical installation (Installation angle 0 ) Figure Installation orientation (Installation angle 0 ) Vertical installation with an angle of 90 to the right/left (Installation angle: 90 to the right/left; only installations in which the product is screwed in are supported) PWR V+ V- (Top) (Top) RUN STS ERR SW LINK/AC T SPEED (Under) (Bottom) Figure Installation orientation (Installation angle: 90 to the right/left; only installations in which the product is screwed in are supported) 16 CPSN-MCB271-S1-041 Reference Manual (Hardware)

22 2 Setup Horizontal installation Figure Installation orientation (Horizontal) Make sure to gain proper space between the product and devices that generate heat or exhaust air so that the ambient temperature stays in the range specified in the environment requirement. Also, the temperature range in the environment requirements varies depending on the installation orientation, so check the operating temperature range in "Chapter 4 System Reference". Recommended installation angle The recommended installation angle for this product is 0. The temperature specifications of the product vary between the case when the installation angle is 90 to the left/right and the case when a plane installation is used, so check the operating temperature range in "Chapter 4 System Reference". Ambient temperature The ambient temperature is decided from the multiple measurement points which are a 50mm-distance from the case. During the operation, adjust the air current to make certain that the temperatures measured in the points stay within the specified temperature. CAUTION - The product is an open-type device (a device designed to be housed inside other equipment) and must always be mounted inside a mechanical enclosure having enough strength. - Note that although the ambient temperature is within the specified range, an operational failure may occur if there is other device generating high heat nearby; the radiation will influence the product to increase its temperature. - Do not install the product into the fully-sealed space except the case in which the internal temperature is adjustable by equipment such as an air conditioner. Long-term usage might increase the temperature and lead to a malfunction or other troubles. - When using the product in a high temperature environment, its life time will be shorten. Perform the forced air cooling to counteract. CPSN-MCB271-S1-041 Reference Manual (Hardware) 17

23 2 Setup Spaces between the product and surrounding objects (Exemplar) Measurement points 50 [mm] Figure Distances between the product and its vicinity (Exemplar) 18 CPSN-MCB271-S1-041 Reference Manual (Hardware)

24 2 Setup Installation and Removal of I/O module and blank panels CAUTION Always confirm the PWR-LED is turned off before installing or removing the module. Installation procedure (1) Paying attention to the horizontal orientation of the I/O module, insert the resin groove into the rail of the CPU unit that has been installed on a DIN rail or that has been screwed into place, and then push the I/O module in until it clicks. The hook is on the left. The groove is on the right. Figure Installing the I/O module and blank panels CPSN-MCB271-S1-041 Reference Manual (Hardware) 19

25 2 Setup Removal procedure (1) Press in the hooks at the top and bottom of the I/O module, and then pull it toward you and out of the CPU unit that has been installed on a DIN rail or that has been screwed into place. Figure Removing the I/O module and blank panels 20 CPSN-MCB271-S1-041 Reference Manual (Hardware)

26 2 Setup Inserting and Removing the microsd CAUTION Always confirm the PWR-LED is turned off before inserting or removing the microsd. - Inserting procedure (1) Slide down the cover of microsd socket. Figure Inserting the microsd<1/5> (2) Open the cover up. Figure Inserting the microsd <2/5> CPSN-MCB271-S1-041 Reference Manual (Hardware) 21

27 2 Setup (3) Insert the microsd card into the cover. Figure Inserting the microsd <3/5> (4) Close the cover. Figure Inserting the microsd <4/5> (5) Slide the cover up to lock it in place. Figure Inserting the microsd <5/5> 22 CPSN-MCB271-S1-041 Reference Manual (Hardware)

28 2 Setup - Removing procedure (1) Slide down the cover of microsd socket. Figure (2) Open the cover up. Removing the microsd<1/5> Figure Removing the microsd<2/5> (3) Remove the microsd card from the cover. Figure Removing the microsd <3/5> CPSN-MCB271-S1-041 Reference Manual (Hardware) 23

29 2 Setup (4) Close the cover. Figure Removing the microsd <4/5> (5) Slide the cover up to lock it in place. Figure Removing the microsd <5/5> 24 CPSN-MCB271-S1-041 Reference Manual (Hardware)

30 2 Setup Cable Connection Cable Connection Regarding connection When connecting the product to an external device, use the supplied connector plug. For wiring connector, strip off the covered part of a wire rod (8mm ± 0.5mm) and insert it to the opening. While pressing the orange part in the center of the connector with a precision screwdriver or a similar tool, insert the cable into the round hole. After that, release the pressed part to fix the cable in place. CAUTION Removing the connector plug by grasping the cable can break the wire. About a caution mark on the product: Use copper wires that tolerate the temperature of 75 degrees Celsius and higher. Figure Cable connection CPSN-MCB271-S1-041 Reference Manual (Hardware) 25

31 2 Setup Power Power Cable Use the power cable described below. - Cable : Twisted pair cable (when using a single wire, twist V+ wire and V- wire) - Cable Diameter : AWG20-16 (0.5mm mm 2 ) - Cable Length : within 3 meters FG Cable Use the FG cable described below. - Cable Diameter : AWG18-16 (0.75mm mm 2 ) Specification of external power supply This product is designed to operate with 30 watt power supply depending on the number of configurable modules. In addition, the power supply must fulfill the following requirements. - Rising time for up to 24 voltage: 2 milliseconds up till 30 milliseconds Recommended power supply is CPS-PWD-30AW24-01 (by CONTEC). CAUTION - If the maximum output current of the external power supply is smaller than the maximum consumption current of this product, the abnormal operations might occur due to the inrush current at the start-up time or the load fluctuation. The aging external power supply could cause a start-up failure. - About a caution mark on the product: Please use copper wires that tolerate the temperature of 75 degrees Celsius and higher. LAN Use the LAN cable described below. - Category : Category 5 or more - Cable Length : within 100 meters 26 CPSN-MCB271-S1-041 Reference Manual (Hardware)

32 2 Setup RS-232C (COM) When using an RS-232C interface, different cables may be required depending on the types of device to which you are connecting (computer or modem, etc.). Check the requirements of the external device and select either a straight-through or crossed (null modem) cable as appropriate. If special treatment of the signal lines in the connector is required, ensure that this is done in accordance with the specifications. Figure Example connection to a modem Figure Example connection to a PC Figure Example connection to a device CPSN-MCB271-S1-041 Reference Manual (Hardware) 27

33 2 Setup See the table below for baud rate that you can set with this product. Table 2.1. Baud Rate List Baud Rate(bps) Error(%) % % % % % % % % % % % % % % % % % % % % % % % % Software Setup Information on the software setup is given in the CPSN-MCB271 Reference Manual (Software), so check that manual. 28 CPSN-MCB271-S1-041 Reference Manual (Hardware)

34 3 Nomenclature and Functions 3. Nomenclature and Functions Nomenclature of Components Component names of the products are shown in Figure 3.1 and Figure PWR V- V RUN STS ERR SW LINK/AC T SPEED Figure 3.1. CPSN-MCB271-S1-041 Nomenclature of components (1) Power Connector : Use the power connector (3 pin connector), included in this package. (2) LED : Indicates the status of the product. (3) RS-232C : It is a RS-232C serial ports (male). (4) Switch : This is used with the software setup. (5) USB : It is a USB port. (6) LAN : It is a connector for LAN. (7) Expansion slot : These are used to supply power to and communicate with expansion modules. (8) microsd Card Slot : It is for data storage. (9) Jumper : Please do not use it. CPSN-MCB271-S1-041 Reference Manual (Hardware) 29

35 3 Nomenclature and Functions Component Functions Power Connector (12-24VDC) Use the 3-pin connector, included in this package. Connector type : DEGSON 15EDGKD P-13-00A(H) (or equivalent) Table 3.1. Power connector Pin No Signal name Meaning 1 FG Frame ground 2 V- Power supply (GND) 3 V+ Power supply (12-24VDC) 30 CPSN-MCB271-S1-041 Reference Manual (Hardware)

36 3 Nomenclature and Functions LED This product is equipped with LEDs (PWR [power], RUN, STS [status], and ERR [error]) that indicate the status. Table 3.2. LED LED Operation Meaning PWR(Green) RUN(Green) STS(Green) ERR(Red) PWR(Green) RUN(Green) STS(Green) ON OFF Flashing Continuous flashing (twice) Continuous flashing (three times) ON OFF Flashing ON OFF Flashing ON OFF All flashing at the same time Initialization is complete. No power supplied. Initialization is in progress. An initialization error occurred. A firmware writing error occurred. The firmware is operating. The product is operating in recovery mode. The recording media (USB, SD) is being accessed. An I/O module is connected. No I/O modules are connected. An I/O module is being accessed correctly. This lights when a system error occurs. - An I/O module cannot be recognized correctly. - An error occurred while accessing an I/O module. This is off when there are no system errors. Data is being written to the firmware or the setup file. CPSN-MCB271-S1-041 Reference Manual (Hardware) 31

37 3 Nomenclature and Functions RS-232C Interface (COM) This product has 1port of RS-232C compliant serial ports of a baud rate 921,600bps (Maximum). Table 3.3. Serial Ports connector No.4-40UNC Inch nut Pin No. Signal name Direction Meaning 1 CD Input Carrier detection 2 RD Input Received data 3 TD Output Transmitted data 4 DTR Output Data terminal ready 5 GND Signal ground 6 DSR Input Data set ready 7 RTS Output Request to send 8 CTS Input Clear to send 9 RI Input Ring indicate 32 CPSN-MCB271-S1-041 Reference Manual (Hardware)

38 3 Nomenclature and Functions Push Switch (SW) This controls the product's power supply. Start in recovery mode: Use this procedure if you need to recover the product when the firmware is corrupted. (Procedure) (1) While holding down the push switch, turn the power ON. (2) When PWR (green LED) lights and RUN (green LED) turns off, the product starts operating in recovery mode. Setup information initialization: Use this procedure to initialize the setup information. (Procedure) (1) When the initialization is finished, press the push switch. (2) PWR (green LED), RUN (green LED), and STS (green LED) start to flash. (3) These LEDs will flash for 3 seconds, so release the push switch while the LEDs are flashing. (4) Wait for PWR (green LED), RUN (green LED), and STS (green LED) to stop flashing. (5) When PWR (green LED), RUN (green LED), and STS (green LED) return to their original statuses, the initialization is complete. USB Port (USB) The product has 1 port of USB interface of TYPE-A. Table 3.4. USB connector 1 4 Pin No. Signal Name 1 USB_VCC 2 DATA- 3 DATA+ 4 USB_GND CPSN-MCB271-S1-041 Reference Manual (Hardware) 33

39 3 Nomenclature and Functions LAN Port (LAN) This product have 1 port of Ethernet. - Network type : 10BASE-T/100BASE-TX - Transmission speed : 10M/100M bps - Maximum network path length : 100m /segment Table 3.5. LAN port Link /Act 1 8 Speed Pin No. Signal Name Meaning 1 TX+ Transmission data(+)output 2 TX- Transmission data (-)output 3 RX+ Received data (+)input 4 N.C. Not connected 5 N.C. Not connected 6 RX- Received data (-)input 7 N.C. Not connected 8 N.C. Not connected Table 3.6. LED indicator (Side, LAN ports) LED Operation Meaning Link /Act(Green) Speed(Orange) ON Flashing OFF ON OFF Indicates that LAN port is connected. Indicate that LAN port is transmitting and receiving data with the connected external device. Indicates that LAN port is not connected. Indicates that LAN port is connected by 100Mbps. Indicates that LAN port is connected by 10Mbps or not connected. 34 CPSN-MCB271-S1-041 Reference Manual (Hardware)

40 3 Nomenclature and Functions Expansion slot This product has four I/O slots in which you can install I/O modules. These slots are used to supply power to and communicate with the I/O modules. CAUTION Do not install or remove I/O modules while power is being supplied to this product. Be sure to check that the LEDs on the main unit are off before installing or removing modules. microsd Card Slot The product is equipped with one microsd card slot. CPSN-MCB271-S1-041 Reference Manual (Hardware) 35

41 3 Nomenclature and Functions 36 CPSN-MCB271-S1-041 Reference Manual (Hardware)

42 4 System Reference 4. System Reference Specifications Table 4.1. Function specifications <1/2> Item CPSN-MCB271-S1-041 CPU Memory ROM ARM Cortex-M3 180MHz On Board 16MB SDRAM On-Board 4MB NOR Flash for OS FeRAM LAN USB microsd Card slot RS-232C Expansion slot LED Switch RTC Transmission standard The number of channels Connector LED Transmission standard The number of channels Connector Standard Connector Baud Rate Data length Parity check The number of channels Isolation Connector Number of slots 4 Maximum power supply Number of insertions/removals Monthly error Backup time - On-Board 32kB 10BASE-T/100BASE-TX 1ch RJ-45 Connector Speed(Orange), Link / Act(Green) USB2.0 standard follow 1ch TYPE-A SD standard follow microsd memory card slot kbps 5, 6, 7, 8 bit 1, 1.5, 2 stopbit Even, Odd, Non-parity 1ch Non-isolated 9-pin D-SUB Connector (Male) 24V 200mA, 5V 250mA, 3.3V 200mA (per slot) 50 times (min) PWR(Green) / RUN(Green) / STS(Green) / ERR(Red) Push switch ±15 seconds or less (25 C) Power supply *1 Rated input voltage Input voltage range Power consumption Connector 12-24VDC VDC 24V 0.08A (Typ.)*2, 1.5A (Max.) 12V 0.15A (Typ.)*2, 2.0A (Max.) 2 pieces 3.5mm pitch 3-pin Terminal (V+, V-, FG) Applicable wire AWG20-16 Physical dimensions (mm) Weight Installation method Surge protection element V+ - V-, V- - FG *1 Use power cable within 3meters. *2 With no USB load and no expansion slot load *3 Commercially available screws are required. Interactive TVS Diode Stand off voltage : ±30V, Peak pulse power : 400W (1ms) 110(W) 74.8(D) 95(H)mm (not include projection) 250g Quick installation on a 35 mm DIN rail Vertical installation with screws *3 CPSN-MCB271-S1-041 Reference Manual (Hardware) 37

43 4 System Reference Table 4.2. Installation Environment Requirements Item Operating ambient temperature -20 to +60 C *1 Operating ambient humidity Non-operating ambient temperature -20 to +60 C *4 Non-operating ambient humidity Floating dust particles Corrosive gases Line-noise resistance Vibration resistance Shock resistance Line noise Static electricity resistance Sweep resistance 10 to 90%RH (No condensation) 10 to 90%RH (No condensation) Not to be excessive None AC Line/±2kV *2 CPSN-MCB271-S1-041 Signal Line/±1kV (IEC Level 3, EN Level 3) Touch/±4kV (IEC Level 2, EN Level 2) Air/±8kV (IEC Level 3, EN Level 3) 10-57Hz*3 / semi-amplitude vibration 0.15mm, Hz / 2.0G 40 minutes each in X, Y, and Z directions (JIS C compliant, IEC compliant) 15G half-sine shock for 11ms in X, Y, and Z directions (JIS C compliant, IEC compliant) Class D grounding (previous class 3 grounding), Impact resistance SG-FG/ non-conduction VCCI Class A, FCC Class A, Standard CE Marking (EMC Directive Class A, RoHS Directive) *1-20 C to +55 C with a vertical installation at an angle of 90 to the left/right or with a plane installation *2 When you use the CPS-PWD-30AW24-01 (optional product) *3 When you use an optional power product: 10-55Hz (See the manual of optional power product for details) Power Requirements System requires a clean, steady power source for reliable performance of the high frequency CPU on the product, the quality of the power supply is even more important. CAUTION - If the fluctuation of power supply voltage is beyond the product specifications, connect a constant voltage transformer. - If the noise is large, connect an isolation transformer (a noise cut transformer). - Never bundle, place nearby or in parallel the power supply cable and the input /output signal lines. - If lightning surge protection is required, connect the surge protective device (SPD). - Ground this product and the surge protective device (SPD) well away from each other. - Please select the ones which do not exceed the maximum allowable circuit voltage for the surge protective device (SPD) at the rise time of the power supply voltage. - Before you restart the power, give the product for at least one second (or more) of the power OFF time after PWR-LED is turned off. - When you use with the CPS-PWD-30AW24-01 (by CONTEC), instantaneous voltage drop allowed time will be 20 millisecond or less. 38 CPSN-MCB271-S1-041 Reference Manual (Hardware)

44 4 System Reference Physical Dimensions Figure 4.1. Physical dimensions CPSN-MCB271-S1-041 Reference Manual (Hardware) 39

45 4 System Reference 40 CPSN-MCB271-S1-041 Reference Manual (Hardware)

46 5 List of Optional Products 5. List of Optional Products DIN rail fitting power supply - CPS-PWD-30AW24-01 : DIN rail fitting power supply 30[w] (Input: VAC, output: 24VDC 1.3 A) I/O module - CPSN-DI-08L : with digital input (input 8 channels, No built-in power supply) - CPSN-DI-08BL : with digital input (input 8 channels, built-in power supply) - CPSN-DI-08L : with digital output (output 8 channels, No built-in power supply) - CPSN-DI-08BL : with digital output (output 8 channels, built-in power supply) - CPSN-AI-1208LI : with analog input - CPSN-COM-1PD : with RS-422A/485 (1channel) * Visit the Contec website regarding information on the optional products. CPSN-MCB271-S1-041 Reference Manual (Hardware) 41

47 Revision History MONTH YEAR January 2018 The First Edition Summary of Changes CONTEC CO., LTD , Himesato, Nishiyodogawa-ku, Osaka , Japan CPSN-MCB271-S1-041 Reference Manual (Hardware) January 2018 Edition No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. [ ] [ ] Management No. NA05978 Parts No. LYVQ151