SELECTOR 4 / 8. Instrument for torque control ASL 11/17

Transcription

1 Instrument for torque control SELECTOR 4 / 8 ASL / ENGLISH Pictograms WARNING It can be dangerous to use this machine if the operating instructions are not carefully followed. Before using the machine, please read the instructions supplied carefully and keep them safe for future reference. ENGLISH Operator s Instructions Pages -6 Spare Parts and Accessories Ordering No.s Page 7 Edition Atlas Copco Tools No Page (8) 00 04

2 .0 Introduction These selectors are designed for up to 4 or 8 different sockets, and are easily connected to the I/O-port on the Tensor DS D3 or PF3000 Controller. No adapter cable is needed, only the communication cable and termination Both selectors work with Tensor DS D3 & PF3000, not with PF000 or Tensor DS D30. The basic functionality of the selector allows the operator to use the same tool for applications with different socket sizes and /or various torque levels, and automatically switch parameter set accordingly. Note Only ferro magnetic sockets can be used.0 Installation When installing the Selector 4/8 please follow instructions below.. Connectors Ref. No. +4 VDC input I/O -Bus cable/termination 3 Hex switch Fig Hex Switch There is a hex switch underneath the Selector(Fig. /Ref. No 3). Turn the switch to the right number/letter. The number indicates the node address on the I/O -Bus When delivered it is pre set to 5 for Selector 4 and 6 for Selector 8. For Tensor DS this should not be changed. For PF 3000, please read PF 3000 manual for detailed information Settings on Hex switch POS. 0 NODE ADDRESS Internal relay in PF3000. Not used A 0 B C D 3 E 4 F 5 Atlas Copco Tools - No

3 .3 Socket holders The socket holders are made of plastic. Holes shall be drilled so that the socket is close to the edge of the socket tray. The active region for the sensor for the socket is shown in Fig.. Make sure that the hole is drilled so that the socket is within this area. See drilling instructions below.. Remove the plate on the right side. Remove the plastic socket holders 3. Measure the sockets that you are going to use. 4. Place the socketholder upside down in a vice. 5. The hole for the socket is to be lined up with the edge of the guiding groove of the socketholder, as shown in fig. 3. Add approximately mm of space between the hole and the socket. Drill size (socket diameter + mm). 6. Drill the hole according to fig Repeat the procedure for every socket you are going to use. 8. Replace the socket holders in the order you want to have your P-sets. See chapter 5.0/ P-set Order. Fig. Sensor area Fig. 3 Edge of guiding groove Text slide On the text slide the name of the P-set can be attached, either with a permanent marker or more preferable written on a paper tag that is attached to the slide. Fig. 4 Socket name Atlas Copco Tools - No

4 .5 Dimensional drawing Fig Mounting Find a spot to mount the Selector on. It is recommended that you use the mounting brackets, position, and fixture it to the surface. Place it so it is possible to see the LED s, position, next to each socket. Screw size 4mm. Fig. 6 Ø Connectors and cables On the Selector there are two connectors for the I/O Bus. Both of these has to be connected. The drive is also equipped with two connectors for the I/O -Bus, which have to be connected as well. Every connector in the system has to be connected, either by a cable, (See page 8) or a termination, Fig. 7 shows how the I/O-bus accessories shall be connected. 4 Atlas Copco Tools - No

5 Fig. 7 Connections = Termination = Cable Atlas Copco Tools - No

6 3.0 LED s (Light Emitting Diodes) Tensor DS Red light = Socket lifted Green light = valid P-set chosen No light = P-set is not opened in drive Fig PF3000 Please read the PF3000 manual for detailed information. 4.0 P-set order Tensor DS The P-sets are listed in the same order as the socket position on the selector tray, starting from left. See Fig In order to turn on/off a position on the selector when connected to Tensor DS, open or delete the P-set corresponding to that position. PF3000 Please read the PF3000 manual for detailed information. Ref. No. P-set (Tensor DS) P-set (Tensor DS) 3 P-set 3 (Tensor DS) etc P-set (Tensor DS) 4 Red LED 5 Green LED 5.0 Power Supply The selector is powered from the DS drive or PF3000 through the I/O-Bus cable. The maximum current output from the DS/PF3000 is 800mA. If there is additional equipment connected to the DS/PF3000 which together with the selector consumes more than 800mA it is necessary to have external power supply. External power to the selector is connected on position in Fig., named ext 4 VDC Input. Note: External Power supply used, has to be insolated and apply to National standards. 6.0 Technical specifications Over all dimensions Length Selector 4 Length Selector 8 Width Height Weight Selector 4 Selector 8 Power consumption Selector 4 Selector 8 Operating voltage Operating conditions Temperature Humidity 0 mm 40 mm 0 mm 65 (75) mm. kg kg max 00 ma (normal 70 ma) max 40 ma (normal 70 ma) 4 VDC 0-50 o C (3- o F 5-95% non-condensing Shipment list Selector 4 or Selector 8 Socket holders, one for each position (not drilled) ( ) Mounting brackets terminations ( ) Operating manual 6 Atlas Copco Tools - No

7 Fig Spare parts & accessories For Selector Screw (MFTS M3x Black chrome) Text slide End plate Rubber seal (r) Rubber seal (l) Crystal emblem 6 Aluminium profile Socket holder 0 mm Socket holder 50 mm For Selector Screw (MFTS M3x Black chrome) Text slide End plate Rubber seal (r) Rubber seal (l) Crystal emblem 6 Aluminium profile Socket holder 0 mm Socket holder 50 mm Fig For Selector Foot Screw (MRT M4x0) 3 Base plate Mounting brackets For Selector Foot Screw (MRT M4x0) 3 Base plate Mounting brackets Sockets Cables available Ordering No meter meter meter meter meter meter 0 Ordering No mm Standard mm Accessory Atlas Copco Tools - No