3M Indoor Protected Building Entrance Terminal (IBET) 4688V Series

Transcription

1 3M Indoor Protected Building Entrance Terminal (IBET) 4688V Series Instructions Underwriters Laboratories (UL 348X) Listed February B

2 2 February B 1.0 General The 3M Indoor Protected Building Entrance Terminal (IBET) 4688V Series provides electrical protection and a termination point for outside plant cable (feeder) and indoor house wiring (distribution) with RJ-21 connectors. The 3M IBET 4688V is Underwriters Laboratories (UL 348X) Listed M IBET 4688V Series Names, Pair Capacity and Module 4688V / / SD-A IBET 4688V / / SD-A IBET 4688V / / SD-A IBET 4688V / / DPM-FR-A IBET 4688V / / DPM-FR-A IBET 4688V / / DPM-FR-A IBET 25-pair HiCat Indoor Building Entrance Terminal with 3M 710 Splicing Module SD 50-pair HiCat Indoor Building Entrance Terminal with 3M 710 Splicing Module SD 100-pair HiCat Indoor Building Entrance Terminal with 3M 710 Splicing Module SD 25-pair HiCat Indoor Building Entrance Terminal with 3M MS 2 Fire Retardant Pluggable Module 4005-DPM/FR 50-pair HiCat Indoor Building Entrance Terminal with 3M MS 2 Pluggable Module 4005-DPM/FR 100-pair HiCat Indoor Building Entrance Terminal with 3M MS 2 Pluggable Module 4005-DPM/FR 1.2 3M IBET Parts and Components a. Connectorized tails with 3M Flame-Retardant modules. 3M MS² Super Mini Splicing Module 4000-D/CO, 3M MS² Fire Retardant Pluggable Module 4005-DPM/FR or 3M 710 Splicing System SD modules. b. Splice chamber for the feeder cable with cable strain relief. c. Insulated #6 ground strap for the feeder cable. d. External bottom-mounted three-point ground bar and top-mounted three-point ground bar. e. Numbered standard five-pin protector receptacle field. f. Fully lockable protective cover. g. Three (3) screws (2 small and 1 large) to wall mount the IBET. (Note diagram in section 2.4.)

3 B February M Indoor Protected Building Entrance Terminal (IBET) Dimensions and Wiring Schematic Model Height Width Depth 4688V V V " 316 mm 12.46" 316 mm 22.79" 579 mm 12.47" 317 mm 12.47" 317 mm 12.47" 317 mm 4.83" 123 mm 4.83" 123 mm 4.83" 123 mm 1.4 Protector Specifications: Use ONLY UL Recognized or Listed five-pin protectors in the 3M 4688V IBET. 1.5 Special Tools Needed to Install: 3M MS 2 Modules or 3M 710 Connectors (Not required if 3M Scotchlok Connectors are used) 2.2 Open the splice chamber by loosening the bolt securing the splice chamber door. Open the splice chamber door. 2.3 Pull the pre-terminated short stub, insulated ground wire and accessories out of the splice chamber. 2.4 Mount the terminal in designated position with the three mounting screws provided. Model Dimension A 4688V " (229 mm) 4688V " (229 mm) 4688V " (327 mm) A 3M Indoor Building Entrance Terminal (IBET) 4688V Wiring Schematic 2.0 3M Indoor Building Entrance Terminal (IBET) Location and Mounting 2.1 Locate the terminal according to your company s standard operating procedures. Consider the following points: a. Locate the terminal inside the building as close as possible to cable entrance. b. Locate the terminal on a firm mounting surface where it will be accessible to the technicians at all times; where it can be reached without a ladder; and where it will not project in a hazardous manner. c. Observe caution when exposing the terminal to chemicals in liquid or vapor form as they may damage the plastic components. Back of terminal: Wall-mounting keyholes 2.5 Remove the jumper wire retaining ring from the poly bag and install in the faceplate. 3.0 Feeder Cable Preparation and Strain Relief 3.1 Feeder cable diameters for the 3M Indoor Building Entrance Terminal (IBET) 4688V Series Min. Diameter Max. Diameter Entrance Cable 0.42" (10.7 mm) 1.45" (36.8 mm) If the cable diameter is smaller than the minimum, use Scotch Linerless Rubber Splicing Tape 130C to build up to the minimum. c Caution Avoid locations near flammable materials, ignitable gases, dust, moisture, temperature extremes, moving machinery, electric light and power circuits, and electrical equipment.

4 4 February B 3.2 Run the feeder cable 24" (610 mm) past the 3M Indoor Building Entrance Terminal (IBET) cable entry port pair 3.3 Slide the 3M Pull N Shrink Tubing (PST) on the end of the cable with the pull-tab away from the 3M IBET and temporarily keep it out of the way. 3.4 With the groove toward the 3M IBET and long end toward the cable, snap the cable gland halves around the cable. Slide the gland into the entry port of the 3M IBET. 3.5 Measure 2" (51 mm) of sheath past the gland inside the 3M IBET. Pull the gland and cable out of the 3M IBET. 3.6 Remove the sheath, leaving at least 21" (533 mm) of free conductor length. Identify and secure the cable groups ends. Bond the cable shield according to your company s practice. 3.7 Insert the gland s groove into the cable port. Slide the 3M Pull N Shrink Tubing (PST) over the gland and slowly unwind the core. The PST tubing fits over either the small diameter of the 25 to 50-pair gland or butts up against the 3M IBET 4688V for the 100-pair gland. 3.8 Complete the PST core removal over the gland. 3.9 The blank plate MUST be used in the empty cable port for UL Listing Attach the cable to the wall according to your company s practice. 100 pair 4.0 Terminal Grounding 4.1 Fasten a #6 AWG wire to the ground bar, which is located on the front of the unit. Connect other end of the ground wire to local ground per company standards. Note: Failure to properly bond and ground the terminal per N.E.C. or local equivalent codes may render protection arrestors useless. 5.0 Splicing 5.1 Splice the feeder cable group(s) to the appropriate terminal block tail(s) per your company s practice. 5.2 Bundle the completed splice module(s) and secure them with 3M Cable Ties within the splice chamber. 5.3 Close the splice chamber cover and secure the lock plate bolt. 2"

5 B February Installing the Electrical Protectors Note: Use ONLY UL Recognized or Listed protectors in the 3M Indoor Building Entrance Terminal (IBET). 6.1 The 3M Indoor Building Entrance Terminal (IBET) 4688V uses a standard five pin protector receptacle field. The long pins of the protector connect Tip and Ring from the feeder cable though the protector to the short pins to the distribution/house wire. 6.2 Insert protectors into the protector receptacle field according to your company s practice. 8.0 Multiple 3M Indoor Building Entrance Terminal (IBET) 4688V Series Installation Use this application when the required cable pair capacity exceeds the capacity of a single 3M IBET. 8.1 The design of the splice chamber and the grooved cable glands make it possible to stack the 3M IBET vertically, up to three of the same cable pair count and within the diameter limits in the chart in Mounting the 3M IBET a. Mount the 3M IBET bodies using the cable glands to position them. b. Assemble the feeder cable strain relief according to Section 3.0 and prepare the feeder cable so that 21" (533 mm) of free conductor length will be in the last IBET. 6.3 To disconnect the distribution wire, pull the protector out to the detents on the long pins to hold it in place. This continues to protect from the feeder cable side. 7.0 Protective Cover 7.1 With the cover closed, the exposed hasp allows for locking when security is required. 1" (25 mm) minimum 21" (533 mm) 2.75" (70 mm) minimum Note: 3M Indoor Building Entrance Terminal (IBET) 4688V 50/25 shown. All 4688V terminal sizes will stack as shown in detail above.

6 8.3 Place cable glands around the free conductors and position into the 3M Indoor Building Entrance Terminal (IBET). 8.4 Separate the feeder cable pair assigned to each 3M IBET; splice and bond the 3M IBET according to section 4.0 Terminal Grounding. 3M, Scotch, MS 2 and Scotchlok are trademarks of 3M Company. Important Notice All statements, technical information, and recommendations related to 3M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any direct, indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. Communication Markets Division 6801 River Place Blvd. Austin, TX Phone Web Please recycle. Printed in USA 3M All rights reserved B