M-Series. Circuit Breaker

Transcription

1 M-Series Circuit Breaker The M-Series is a low cost, miniature hydraulic/magnetic circuit breakers ideally designed for demanding applications requiring space saving features, aesthetics and snap-in front panel mounting. Its newest design features a compact, space saving, vertically mounted parallel pole configuration, which is UL489A listed up to 50 amps and is well suited for telecommunication equipment fitting in one rack unit. Furthermore, it features two uniquely designed terminals that provide the highest level of balanced circuit protection. In addition, these circuit breakers feature various styling options allowing for design flexibility. They are available in choices of rocker actuator styles and colors, including paddle and baton style handle actuators, push-to-reset and push-pull pushbutton actuators, Visi-Rocker two color actuators as well as non-illuminated or illuminated rocker versions with LED or neon bulbs. The exclusive Rockerguard bezel helps prevent inadvertent actuation and wiping contact design insures long-term reliability. The M-Series circuit breakers are available in & poles or parallel poles, 0.0 to 50 amps, up to 50VAC or 80VDC with choices of time delays, terminals, panel hardware, actuator styles, colors, and imprinting. Features: Parallel pole configuration well suited for One Rack Unit Meets CSA Standard. No. 00 for Generator & Welder markets MIL-PRF-5569 and MIL STD 0 compliant MIL-PRF-3909F ingress protection Sealed toggle actuator Compact design Applications: Communication equipment Vehicles Marine Generators Power supplies Medical Equipment Carling Technologies, Inc. 60 Johnson Avenue Plainville, CT Phone: (860) Fax: (860)

2 M-Series Circuit Breaker - General Specifications Electrical Maximum Voltage 5/50 VAC 50/60 Hz, 80 VDC (See Rating Tables.) Current Ratings Standard current coils: 0.00, 0.50, 0.500, 0.750,.00 thru 5.0 in amp increments, 8.0, 0.0, 5.0, Other ratings available - see Ordering Scheme. Auxiliary Switch Rating SPDT; 7A 50VAC, 7A (Res) 8VDC, 4A (Ind.) 8VDC, 0.5A 80VDC (Res) (silver contacts), 0.A 5VAC (gold contacts). Insulation Resistance Minimum of 00 Megohms at 500 Dielectric Strength RESISTANCE PER POLE VALUES from Line to Load Terminals (Values Based on Series Trip Circuit Breaker) *Manufacturer reserves the right to change product specification without prior notice. VDC. UL, CSA 500V, 50/60 Hz for one minute between all electrically isolated terminals. M-Series Circuit Breakers comply with the 8mm spacing and 3750 V 50/60Hz dielectric requirements from hazardous voltage to operator accessible surfaces, per Publications IEC 380, 435, 950, EN and VDE Resistance, Impedance Values from Line to Load Terminal - based on Series Trip Circuit Breaker. Pulse Tolerance Curves CURRENT TOLERANCE (AMPS) (%) ± ±35 Mechanical Endurance 0,000 ON-OFF 6 per minute with rated Current and Voltage. Trip Free All M-Series Circuit Breakers will trip on overload, even when actuator is forcibly held in the ON position. Trip Indication The actuator moves positively to the OFF position when an overload causes the circuit breaker to trip. Physical Number of Poles or Internal Circuit Configs. Series with or without Auxiliary Switch. Switch Only with or without Auxiliary Switch. Weight Approximately 30 grams/pole (Approximately.07 ounces/pole) Standard Colors See Ordering Scheme.a Environmental Designed in accordance with requirements of specification MIL PRF-5569 & MIL-STD-0G as follows: Shock Withstands 00 Gs, 6ms, sawtooth while carrying rated current per Method 3, Cond. I. Instantaneous curves tested at 80% of rated current. Vibration Withstands excursion from 0-55 Hz, and 0 Gs Hz, at rated current per Method 04C, Test Condition A. Instantaneous curves tested at 80% of rated current. Moisture Resistance Method 06D, i.e., ten 4-hour + 5 C to +65 C, 80-98% RH. Salt Spray Method 0, Condition A (90-95% 5% NaCl Solution, 96 hrs). Thermal Shock Method 07D, Condition A (Five -55 C to +5 C to +85 C to +5 C). Operating Temperature -40 C to +85 C Chemical Resistance Only the outside surfaces of the case and the handles may be cleaned with detergents or alcohol. Organic (hydrocarbon based) solvents are not recommended because they attack plastics. Caution should be taken when solvents are used to clean and remove flux from terminals. Lubricants should not be introduced into the handle/ bushing openings

3 M-Series Circuit Breaker - General Specifications 3 Electrical Tables Table A: Lists UL Recognized and CSA Accepted configurations & performance capabilities as a Component Supplementary Protector. Table A Polarity Sensitive Available only with Special Catalog Number. Consult Factory. 3 Requires Branch Circuit Backup with a UL Listed type K-5 or RK-5 fuse rated 30 Amps maximum 4 Requires Branch Circuit Backup with a UL Listed type K-5 or RK-5 fuse rated 60 Amps maximum Table B: Lists UL Recognized,CSA Accepted and TUV and VDE Certified configurations and performance capabilities as a Component Supplementary Protector. Table B Polarity Sensitive Available only with Special Catalog Number. Consult Factory. 3 Requires Branch Circuit Backup with a UL Listed type K-5 or RK-5 fuse rated 30 Amps maximum 4 TUV only, not VDE 5 Requires backup protection with a thermal magnetic circuit breaker rated 3 amps and having a Type C trip characteristic per EN60898/DIN VDE 064 (C3A) for ratings greater than 5amps, and a thermal magnetic circuit breaker rated 6 amps and having a Type C trip characteristic per EN60898/DIN VDE 064 (C6A) for ratings 5 amps and less

4 4 M-Series Circuit Breaker - General Specifications Electrical Tables Table C: Lists UL489A Listed and TUV Certified configurations and performance capabilities for use in Communications Equipment. M-SERIES TABLE C: UL489A Listed Table C Available only with Special Caralog Number Table D: Lists UL489A Listed configurations and performance capabilities for use in Communications Equipment. M-SERIES TABLE D: Parallel Pole Construction UL489A Listed (COMMUNICATIONS EQUIPMENT - POLARITY SENSITIVE) CIRCUIT CONFIGURATION SERIES MAX. RATING VOLTAGE FREQUENCY CURRENT RATING GENERAL PURPOSE AMPS POLES BREAKING INTERRUPTING CAPACITY (AMPS) WITHOUT BACKUP FUSE UL489A 80 DC DC Table D Available only with Special Caralog Number Agency Certifications UL Recognized UL Standard 077 Component Recognition Program as Protectors, Supplementary (Guide CCN/QVNU, File E75596) CSA Accepted Component Supplementary Protector (Class 35 30, File ) CSA Standard C. No. 35 UL Listed UL Standard 489A Communications Equipment (Guide CCN/DITT, File E8995) VDE Certified EN60934, VDE 064 under File 0537 TUV Certified EN60934, under License No. R96709

5 M-Series Parallel Pole Rocker - Ordering Scheme 5 M E P D A B T Series 3 Poles 4 Circuit 5 Frequency & Delay 6 Current Rating 7 Terminal 8 Illumination 9 Color & Legend 0 Legend Bezel Color Agency Approval SERIES M ACTUATOR Single Color Rocker Two Color Visi-Rocker Single Color Translucent Rocker A Angled D Indicate ON F Angled B Flat E Indicate OFF G Flat 7 TERMINAL A Push in Stud Screw (Bus Type) 8 ILLUMINATION Non-Illuminated A Non-Illuminated 3 POLES Two 4 CIRCUIT/AUXILIARY SWITCH P Series Trip Current (Parallel Pole) with Auxiliary Switch, Silver Contacts Q Series Trip Current (Parallel Pole).0 x 0.0 Q.C with Auxiliary Switch, Gold Contacts R Series Trip Current (Parallel Pole).0 x 0.0 Q.C 5 FREQUENCY & TIME DELAY D DC Short D4 DC Medium 6 CURRENT RATING (AMPERES) CODE AMPERES ACTUATOR COLOR & LEGEND Visi Legend 3 Red 4 Green 5 Blue 6 Yellow 7 Gray 8 Orange 0 LEGEND ON - OFF Vertical 3 ON - OFF Horizontal 6 Dual Vertical 7 Dual Horizontal BEZEL COLOR A without Rockerguard B without Rockerguard G Gray without Rockerguard with Rockerguard with Rockerguard 7 Gray with Rockerguard AGENCY APPROVAL T UL 489A Listed Reminder of Rocker same color as Visi Aux Switch only available with screw terminals

6 6 M-Series Parallel Pole - Handle / Push Button - Ordering Scheme M M P D B B B T Series 3 Poles 4 Circuit 5 Frequency & Delay 6 Current Rating 7 Terminal 8 Color 9 Front Panel Hardware 0 Legend Plate/ Marking Brushing Color Agency Approval SERIES M ACTUATOR M Paddle T Push-Pull 3 POLES Two 4 CIRCUIT/AUXILIARY SWITCH P Series Trip Current (Parallel Pole) with Auxiliary Switch, Silver Contacts Q Series Trip Current (Parallel Pole).0 x 0.0 Q.C with Auxiliary Switch, Gold Contacts R Series Trip Current (Parallel Pole).0 x 0.0 Q.C 5 FREQUENCY & TIME DELAY D DC Short D4 DC Medium 6 CURRENT RATING (AMPERES) CODE AMPERES TERMINAL A Push in Stud Screw (Bus Type) 9 FRONT PANEL HARDWARE Handle A No outer Panel Hardware B Knurled Nut, Bright Nickel C Knurled Nut, Bright Nickel w/locking Ring D Knurled Nut, E Knurled Nut, w/locking Ring F Panel Dress, Bright Nickel G Panel Dress, Bright Nickel w/locking Ring H Panel Dress, J Panel Dress, w/locking Ring Push Button No outer Panel Hardware Knurled Nut, Bright Nickel 0 LEGEND PLATE / BUTTON MARKING Handle Legend Plate B ON - OFF Vertical C ON - OFF Horizontal Push-Pull Legend Plate Rated Amps Horizontal 3 Rated Amps Line Side Down 4 Rated Amps Line Side Up BUSHING COLOR B AGENCY APPROVAL T UL 489A Listed Aux Switch only available with screw terminals 8 ACTUATOR COLOR & LEGEND Handle 3 Red 4 Green 5 Blue 6 Yellow 7 Gray 8 Orange Push Button A B C Red D Green E Blue F Yellow G Gray H Orange

7 M-Series Parallel Pole - Form & Fit Drawings 7 PUSH-IN STUD PARALLEL POLE TERMINAL OPTIONS 0-3 SCREW W/ BUS BAR.9 [3.6].65 [6.56].5 [8.58].000 [5.4].393 [9.97].54 [3.9].838 [.9].000 [5.4].00 [.54].750 [9.05] ROCKER ACTUATOR DETAIL INDICATE "ON" (VISI-ON).394 [35.4].370 [9.40] MAX. ±.00 [±.508] ±.00 [±.508].530 [38.86].304 [33.] LINE.970 [4.64] OFF ON.560 [39.6].5 [8.58].375 [34.93] LOAD.400 [0.6].00 [.54].65 [5.88] INDICATE "OFF" (VISI-OFF) & SINGLE COLOR ROCKERGUARD CONFIGURATION ON OFF LOAD LINE ON OFF PANEL CUT - OUT DETAIL (ROCKER) DOUBLE POLE PANEL THICKNESS ±.00 ± [7.4] ±.00 ± [6.67] DIM. A ±.00 ± [7.75] LOAD LINE NOTE. A. T 3. D 4. I- V 5. N O IN DIM. A ±.005 ±.3.39 [33.76].06 [.57].093 [.36].5 [3.8].385 [35.8].40 [36.07].460 [37.08] ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]. TOLERANCE ±.00 [.5] UNLESS OTHERWISE SPECIFIED. 3 DIMENSIONS APPLY TO BOTH ROCKER STYLES. 4 I-O, ON-OFF OR DUAL LEGENDS AVAILABLE FOR VERTICAL OR HORIZONTAL MOUNTING. 5 NOTICE THAT CIRCUIT BREAKER LINE AND LOAD TERMINAL ORIENTATION ON INDICATE OFF IS OPPOSITE THAT OF INDICATE ON.

8 8 M-Series Parallel Pole - Form & Fit Drawings PADDLE ACTUATOR STYLE PUSH-PULL ACTUATOR STYLE /-3 THD. 3/8" 8-3 THD. ON OFF FLAT ±.030 ± [.70].470 [.94] FLAT ±.030 ±.76 ACTUATOR COLOR VISIBLE IN OFF POSITION ONLY.500 [.70] OFF (SHOWN).400 [0.6] ±.030 ±.76 ±.030 ± [7.] ON ±.005 [±.3].355 [9.0] WITH LOCKING RING MOUNTING DETAILS DIA [Ø.70] DIA [Ø3.8] DIA [Ø.70] ±.00 [±.050]. [5.64] WITHOUT LOCKING RING ±.00 ±.05.6 [4.].65 [5.87] DIA MOUNTING DETAILS PUSH-PULL, PUSH TO RESET.544[3.8] [9.53] DIA.534 [3.56] PANEL HARDWARE.494 [.55] HEX NUT.56 [3.56].098 [.49].078 [.98].05 [.64] LEGEND PLATES.340 [8.64].63 DIA [Ø6.05] SNAP-IN BUSHING.435 [.05] DIA 0N PANEL DRESS NUT 0FF.05 [6.04] O N O F F BUTTON MARKING ORIENTATION LEGEND CODE: B C PANEL HARDWARE.65 [5.88].680 DIA [Ø7.7].5 [3.8].80 [4.57] HEX NUT PANEL DRESS NUT.680 DIA [Ø7.7].05 [.67].34 [8.69].5 [3.8] LINE MARKING CODE: 0 LINE LINE QC AUXILIARY SWITCH TERMINALS NOTES:. ALL DIMENSIONS ARE I. TOLERANCE ±.00 [.5] 3. DIMENSIONS APPLY TO 4. I-O, ON-OFF OR DUAL L VERTICAL OR HORIZON 5. NOTICE THAT CIRCUIT ORIENTATION ON INDIC INDICATE "ON". KNURLED NUT.683 DIA [Ø7.7] LOCKING RING.03 [.79] TITLE ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]. TOLERANCE ±.00 [.5] UNLESS OTHERWISE SPECIFIED. 3 DIMENSIONS APPLY TO BOTH ROCKER STYLES. 4 I-O, ON-OFF OR DUAL LEGENDS AVAILABLE FOR VERTICAL OR HORIZONTAL MOUNTING. 5 NOTICE THAT CIRCUIT BREAKER LINE AND LOAD TERMINAL ORIENTATION ON INDICATE OFF IS OPPOSITE THAT OF INDICATE ON. DR BY ME 5/0/

9 M-Series Handle/Pushbutton UL Recognized - Ordering Scheme 9 M M B B B C B Series 3 Poles 4 Circuit 5 Frequency & Delay 6 Current Rating 7 Terminal 8 Color 9 0 Front Panel Legend Hardware Plate Bushing Color Agency Approval SERIES M ACTUATOR Handle M Paddle Push Button T Push-Pull Push Button w/ Snap-In Mounting V Push-Pull 3 POLES One Two N U W Baton Push To Reset Push To Reset 6 CURRENT RATING (AMPERES) 8 CODE AMPERES CIRCUIT without Auxiliary Switch A Switch Only (no coil), Maintained Contacts B Series Trip (Current) with Auxiliary Switch, Silver Contacts Terminal Type: M Series Trip (Current) Aux Switch.0 QC x.00 QC P 3 Switch Only, Maintained Contacts.060 Dia, Round Solder Turret Q 3,4 Switch Only, Maintained Contacts.058 Dia, Round Q.C. R 3,3 Switch Only, Maintained Contacts.080 Dia x.00 Flat Q.C. S 3 Series Trip (Current).060 Dia, Round Solder Turret T 3,4 Series Trip (Current).058 Dia, Round Q.C. U 3,3 Series Trip, Maintained Contacts.080 Dia x.00 Flat Q.C. with Auxiliary Switch, Gold Contacts 3,4 Switch Only, Maintained Contacts.058 Dia, Round Q.C. 3 3,3 Switch Only, Maintained Contacts.080 Dia x.00 Flat Q.C. 4 3,4 Series Trip (Current).058 Dia, Round Q.C. 5 3,3 Series Trip, Maintained Contacts.080 Dia x.00 Flat Q.C. 9 Series Trip (Current) Aux Switch.0 QC x.00 QC 5 FREQUENCY & DELAY 03 DC 50/60Hz, Switch Only 0 DC Instantaneous DC Short 4 DC Medium 0 50/60Hz Instantaneous 50/60Hz Short 4 50/60Hz Medium 30 DC, 50/60Hz Instantaneous 3 DC, 50/60Hz Short 34 DC, 50/60Hz Medium 6 50/60Hz Short, Hi-Inrush 64 50/60Hz Medium, Hi-Inrush 7 DC, Short,Hi-Inrush 74 DC,Medium, Hi-Inrush 9 DC, 50/60Hz Short, Hi-Inrush 94 DC, 50/60Hz Medium, Hi-Inrush 7 TERMINAL 8 Push-On 0.50 Tab (Q.C.) 0 Screw 8-3 w/upturned lugs 3 0 Screw 8-3 (Bus Type) 8 ACTUATOR COLOR & LEGEND 5 Gloss Handle Push-Button A B 3 C 4 D 5 E 6 F 8 H 9 FRONT PANEL HARDWARE 6 No outer Panel Hardware Knurled Nut Bright nickel Bright nickel w/ locking ring w/ locking ring Panel Dress Nut Bright nickel Bright nickel w/ locking ring w/ locking ring Handle A B C D E F G H J A P Push-In Stud Printed Circuit Board Acuator Color Red Green Blue Yellow Orange Push-Button One actuator is located in the center of each multi-pole breaker. codes V & W limited to single pole breakers only. Switch Only circuits are not available with Push-To-Reset actuators. For Switch Only circuits, select Current Coil Rating from the above chart: 3 One Auxiliary Switch is supplied per breaker. On two-pole breakers, standard Auxiliary Switch mounting is in pole one. Auxiliary Switch option limited to Series Trip and Switch Only circuits. Not available with back connect screw or push-in stud terminals. 4 Mates with AMP.058 diameter pin receptacles including (gold plated) and (tin plated). 5 color is only visible in the OFF position on Push-Pull actuators. 6 All units except snap-in mounting have one hex nut installed on bushing for use behind the panel. 7 Other colors available. Consult factory. 8 TUV and VDE Certification above 5 amps is for -pole only and is limited to a max. of 5 amps. Screw Terminal or Push-In Stud recommended above 0 amps amp rating not available with delay s 30, 3, 34, 9 or Screw Terminals are VDE certified only with use of ring terminal attached to wire. Terminal code A available with circuit codes A & B only. Printed circuit board available with UL recognized approval only. 3 Auxiliary switch (flat Q.C.) available with UL recognized approvals only. 0 LEGEND PLATE / BUTTON MARKING Handle Legend Plate ( Styles M & N) A No Legend Plate B ON - OFF Vertical C ON - OFF Horizontal D I - O Vertical E I - O Horizontal Push-Pull Button Cap ( Styles T & V) No Marking Rated Amps Horizontal 3 Rated Amps Line Side Down 4 Rated Amps Line Side Up Push-to-Reset Button ( Styles U& W) No Marking BUSHING COLOR 7 B AGENCY APPROVAL 8 C UL Recognized & CSA Accepted D VDE Certified, UL Recognized & CSA Accepted E TUV Certified, UL Recognized & CSA Accepted

10 0 M-Series Handle/Pushbutton UL489A/UL Recognized Ordering Scheme M M B 4 60 B B B J Series 3 Poles 4 Circuit 5 Frequency & Delay 6 Current Rating 7 Terminal 8 Color 9 0 Front Panel Legend Hardware Plate Bushing Color Agency Approval SERIES M ACTUATOR 7 TERMINAL 4 Push-On 0.50 Tab (Q.C.) Screw 8-3 w/upturned lugs 3 Screw 8-3 (Bus Type) A 0 P Push-In Stud Printed Circuit Board Handle M Paddle Push Button T Push-Pull Push Button w/ Snap-In Mounting V Push-Pull N U W Baton Push To Reset Push To Reset 8 ACTUATOR COLOR & LEGEND 5 Gloss Handle Push-Button A B 3 C 4 D 5 E 6 F 8 H Acuator Color Red Green Blue Yellow Orange 3 POLES One 4 CIRCUIT without Auxiliary Switch B Series Trip (Current) with Auxiliary Switch, Silver Contacts Terminal Type: M Series Trip (Current) Aux Switch.0 QC x.00 QC S Series Trip (Current).060 Dia, Round Solder Turret T,3 Series Trip (Current).058 Dia, Round Q.C. U 3, Series Trip, Maintained Contacts.080 Dia x.00 Flat Q.C. with Auxiliary Switch, Gold Contacts 4,3 Series Trip (Current).058 Dia, Round Q.C. 5 3, Series Trip, Maintained Contacts.080 Dia x.00 Flat Q.C. 9 Series Trip (Current) Aux Switch.0 QC x.00 QC 5 FREQUENCY & DELAY DC Short 4 DC Medium 6 CURRENT RATING (AMPERES) CODE AMPERES DC, Short,Hi-Inrush 74 DC,Medium, Hi-Inrush FRONT PANEL HARDWARE 6 No outer Panel Hardware Knurled Nut Bright nickel Bright nickel w/ locking ring w/ locking ring Panel Dress Nut Bright nickel Bright nickel w/ locking ring w/ locking ring BUSHING COLOR 7 B Handle A B C D E F G H J AGENCY APPROVAL 9 J UL489A Listed, TUV Certified M UL Recognized, CSA Accepted N UL Recognized, TUV Certified T UL489A Listed Push-Button 0 LEGEND PLATE / BUTTON MARKING Handle Legend Plate ( Styles M & N) A No Legend Plate B ON - OFF Vertical C ON - OFF Horizontal D I - O Vertical E I - O Horizontal Push-Pull Button Cap ( Styles T & V) 8 No Marking Rated Amps Horizontal 3 Rated Amps Line Side Down 4 Rated Amps Line Side Up Push-to-Reset Button ( Styles U& W) 8 No Marking One actuator is located in the center of each multi-pole breaker. codes V & W limited to single pole breakers only. One Auxiliary Switch is supplied per breaker. On two-pole breakers, standard Auxiliary Switch mounting is in pole one. Auxiliary Switch option limited to Series Trip and Switch Only circuits. Not available with Back Connected Screw or Push-in Stud terminals. 3 Mates with AMP.058 diameter pin receptacles including (gold plated) and (tin plated). 4 Screw terminals or Push-in Stud recommended above 0 amps. 5 color is only visible in the OFF position on Push-Pull actuators. 6 All units have one hex nut installed on bushing for use behind the panel. 7 Other colors available. Consult factory. 8 Not available with UL489A Listed breakers. 9 TUV certified to 5 amps. UL Recognized, CSA Accepted and UL Listed to 30 amps. 0 Terminal code A available with circuit codes A & B only. Printed circuit board available with UL recognized approval only. Auxiliary switch (flat Q.C.) available with UL recognized approvals only.

11 M-Series Handle Circuit & Terminal Diagrams All dimensions are in inches [millimeters]. Tolerance ±.00 [.5] unless otherwise specified.

12 M-Series Handle PC Terminal Diagrams All dimensions are in inches [millimeters]. Tolerance ±.00 [.5] unless otherwise specified.

13 M-Series Handle - Form & Fit Drawings 3 All dimensions are in inches [millimeters]. Tolerance ±.00 [.5] unless otherwise specified.

14 4 M-Series Pushbutton Circuit & Terminal Diagrams All dimensions are in inches [millimeters]. Tolerance ±.00 [.5] unless otherwise specified.

15 M-Series Pushbutton Form & Fit Drawings 5 All dimensions are in inches [millimeters]. Tolerance ± 0.0 [.5] unless otherwise specified. 3 Available with Push-Pull or Push-to-Reset s

16 6 M-Series Push-Pull PC Terminal Drawings All dimensions are in inches [millimeters]. Tolerance ±.00 [.5] unless otherwise specified.

17 M-Series Rocker UL Recognized Ordering Scheme 7 M G B H C 6 7 C Series 3 Poles 4 Circuit 5 Frequency & Delay 6 Current Rating 7 Terminal 8 Illumination 9 Color 0 Legend Bezel Color Agency Approval SERIES M ACTUATOR Non-Illuminated single color A Angled B Flat Two Color Visi-Rocker D Indicate ON E Indicate OFF 3 POLES One Two llluminated single color F Angled G Flat 6 CURRENT RATING (AMPERES) 8 CODE AMPERES CIRCUIT without Auxiliary Switch A Switch Only (no coil), Maintained Contacts B Series Trip (Current) with Auxiliary Switch, Silver Contacts Terminal Type: M Series Trip (Current) Aux Switch.0 QC x.00 QC P 3 Switch Only, Maintained Contacts.060 Dia, Round Solder Turret Q 3,4 Switch Only, Maintained Contacts.058 Dia, Round Q.C. R 3,6 Switch Only, Maintained Contacts.080 Dia x.00 Flat Q.C. S 3 Series Trip (Current).060 Dia, Round Solder Turret T 3,4 Series Trip (Current).058 Dia, Round Q.C. U 3,6 Series Trip, Maintained Contacts.080 Dia x.00 Flat Q.C. with Auxiliary Switch, Gold Contacts 3,4 Switch Only, Maintained Contacts.058 Dia, Round Q.C. 3 3,6 Switch Only, Maintained Contacts.080 Dia x.00 Flat Q.C. 4 3,4 Series Trip (Current).058 Dia, Round Q.C. 5 3,6 Series Trip, Maintained Contacts.080 Dia x.00 Flat Q.C. 9 Series Trip (Current) Aux Switch.0 QC x.00 QC 5 FREQUENCY & DELAY 03 DC 50/60Hz, Switch Only 0 DC Instantaneous DC Short 4 DC Medium 0 50/60Hz Instantaneous 50/60Hz Short 4 50/60Hz Medium 30 DC, 50/60Hz Instantaneous 3 DC, 50/60Hz Short 34 DC, 50/60Hz Medium 6 50/60Hz Short, Hi-Inrush 64 50/60Hz Medium, Hi-Inrush 7 DC, Short,Hi-Inrush 74 DC,Medium, Hi-Inrush 9 DC, 50/60Hz Short, Hi-Inrush 94 DC, 50/60Hz Medium, Hi-Inrush One actuator is located in the center of each multi-pole breaker. For Switch Only circuits, select Current Coil Rating from the above chart: 3 One Auxiliary Switch is supplied per breaker. On two-pole breakers, standard Auxiliary Switch mounting is in pole one. Auxiliary Switch option limited to Series Trip & Switch Only circuits, & is not available in single pole illuminated breakers, or Back Connected Screw or Push-in Stud terminals. 4 Mates with AMP.058 diameter pin receptacles: (gold plated) & (tin plated). 5 For neon bulb applications at 47K, /4 WATT and for 50VAC 50K, /4 WATT, external resistors must be supplied by customer. 6 On Visi-Rocker breakers, Visi portion of rocker cannot be the same color as the bezel. 7 For LED (DC or rectified AC) applications, LED is mounted in the center of the rocker actuator with electrical characteristics: 00 millicandela at 0mA; Maximum power dissipation = 75mW at 5 C; Maximum forward current = 5mA; Typical forward voltage =.V at 0mA; Typical reverse current = 00uA at 3V. Customer supplies the proper external resistor limiting current to these values. 8 Rocker color for LED s and green neon lamp must be clear, smoke gray, white translucent or match color of LED or neon lamp. 9 Other colors available. Consult factory. 0 TUV 0A, VDE 5A Certified to 5 amps. UL Recognized and CSA Accepted to 30 amps. Screw Terminals or Push-in Stud recommended above 0 amps. TUV or VDE Certified must have I-O or Dual Legends. Legend required on Visi-Rocker breakers. 30 amp rating not available with delay s 30, 3, 34, 9 or Screw Terminals are VDE certified only with use of ring terminal attached to wire. 4 Terminal code A available with circuit codes A & B only. 5 Printed circuit board available with UL recognized approval only. 6 Auxiliary switch (flat Q.C.) available with UL recognized approvals only. 7 TERMINAL 8 Push-On 0.50 Tab (Q.C.) 0 Screw 8-3 w/upturned lugs 3 0 Screw 8-3 (Bus Type) 8 ROCKER ILLUMINATION Non-illuminated Neon 5 without resistor, 0VAC/50VAC LED 7,8 without resistor with resistor, 4-8 VDC with resistor, 9-6 VDC 9 ACTUATOR & LEGEND COLOR Solid Color 3 Red 4 Green 5 Blue 6 Yellow 7 Gray 8 Orange Visi-Rocker Illuminated 8 A B C D E F A Neon B Red D E F Green Glow 8 C Green G H J Legend Legend BEZEL COLOR / STYLE 9 Color without Rockerguard with Rockerguard A B Gray G 7 AGENCY APPROVAL 0 C UL Recognized & CSA Accepted D VDE Certified, UL Recognized & CSA Accepted E TUV Certified, UL Recognized & CSA Accepted Amber K L M Visi & Legend (remainder of rocker same color as bezel) Red Green Blue Yellow Gray Orange Clear Red Transparent Green Transparent Amber Transparent Smoke Gray Transparent Translucent 0 LEGEND No Legend ON - OFF Vertical 3 ON - OFF Horizontal A P Push-In Stud Printed Circuit Board 4 I - O Vertical 5 I - O Horizontal 6 Dual Vertical 7 Dual Horizontal

18 8 M-Series Rocker UL489A/UL Recognized Ordering Scheme M A B 4 60 A 6 J Series 3 Poles 4 Circuit 5 Frequency & Delay 6 Current Rating 7 Terminal 8 Illumination 9 Color 0 Legend Bezel Color Agency Approval SERIES M ACTUATOR Non-Illuminated single color A Angled B Flat Two Color Visi-Rocker D Indicate ON E Indicate OFF llluminated single color F Angled G Flat 7 TERMINAL 9 Push-On 0.50 Tab (Q.C.) Screw 8-3 w/upturned lugs 3 Screw 8-3 (Bus Type) 8 ILLUMINATION Non-illuminated Neon 4 without resistor, 0VAC/50VAC LED without resistor 5,7 with resistor, 4-8 VDC with resistor, 9-6 VDC A Neon B Red D E F A P Push-In Stud Printed Circuit Board Green Glow 7 C Green G H J Amber K L M 3 POLES One 4 CIRCUIT without Auxiliary Switch B Series Trip (Current) with Auxiliary Switch, Silver Contacts Terminal Type: M Series Trip (Current) Aux Switch.0 QC x.00 QC S Series Trip (Current).060 Dia, Round Solder Turret T 3 Series Trip (Current).058 Dia, Round Q.C. U 3,3 Series Trip, Maintained Contacts.080 Dia x.00 Flat Q.C. with Auxiliary Switch, Gold Contacts 4 3 Series Trip (Current).058 Dia, Round Q.C. 5 3,3 Series Trip, Maintained Contacts.080 Dia x.00 Flat Q.C. 9 Series Trip (Current) Aux Switch.0 QC x.00 QC 5 FREQUENCY & DELAY 0 DC Instantaneous DC Short 6 CURRENT RATING (AMPERES) 8 CODE AMPERES DC Medium 7 DC, Short,Hi-Inrush 74 DC,Medium, Hi-Inrush One actuator is located in the center of each multi-pole breaker. One Auxiliary Switch is supplied per breaker. Auxiliary Switch option limited to Series Trip & Switch Only circuits, and is not available in single pole illuminated breakers, or with Back Connected Screw or Push-in Stud terminals. 3 Mates with AMP.058 diameter pin receptacles: (gold plated) & (tin plated). 4 For neon bulb applications at 47K, /4 WATT and for 50VAC 50K, /4 WATT, external resistors must be supplied by customer. 5 For LED (DC or rectified AC) applications, LED is mounted in the center of the rocker actuator with electrical characteristics as follows: 00 millicandela at 0mA; Maximum power dissipation = 75mW at 5 C; Maximum forward current = 5mA; Typical forward voltage =.V at 0mA; Typical reverse current = 00uA at 3V. Customer supplies the proper external resistor limiting current to these values. 6 On Visi-Rocker breakers, Visi portion of rocker cannot be the same color as the bezel. 7 Rocker color for LED s and green neon lamp must be clear, smoke gray, white translucent or match color of LED or neon lamp. 8 Other colors available. Consult factory. 9 TUV Certified to 5 amps. UL Recognized, CSA Accepted and UL489A Listed to 30 amps. Screw Terminals recommended above 0 amps. 0 UL489A Listed must have ON-OFF or Dual legends. TUV Certified approvals must have I - O or Dual legends. Terminal code A available with circuit codes A & B only. Printed circuit board available with UL recognized approval only. 3 Auxiliary switch (flat Q.C.) available with UL recognized approvals only. 9 ACTUATOR & LEGEND COLOR Solid Color 3 Red 4 Green 5 Blue 6 Yellow 7 Gray 8 Orange Visi-Rocker Illuminated 7 A B C D E F Legend Visi & Legend (remainder of rocker same color as bezel) Red Green Blue Yellow Gray Orange Clear Red Transparent Green Transparent Amber Transparent Smoke Gray Transparent Translucent Legend 0 LEGEND 0 No Legend (Single Color or Illuminated Rocker Options Only) ON - OFF Vertical 3 ON - OFF Horizontal 4 I - O Vertical 5 I - O Horizontal 6 Dual Vertical 7 Dual Horizontal BEZEL COLOR / STYLE 8 Color without Rockerguard with Rockerguard A B Gray G 7 AGENCY APPROVAL 9 J UL489A Listed & TUV Certified M UL Recognized & CSA Accepted N TUV Certified, UL Recognized & CSA Accepted T UL489A Listed

19 M-Series Rocker Circuit & Terminal Diagrams 9 All dimensions are in inches [millimeters]. Tolerance ±.00 [.5] unless otherwise specified. 3 Schematic shown represents current trip circuit.

20 0 M-Series Rocker Form & Fit Drawings Dimensions apply to all variations shown. Notice that circuit breaker line & load terminal orientation on indicate OFF is opposite of indicate ON. I-O, ON-OFF or dual legends available for vertical or horizontal mounting. For pole orientation with horizontal legend, rotate front view clockwise All dimensions are in inches [millimeters]. 4 Tolerance ± 0.0 [.5] unless otherwise specified.

21 M-Series Rocker Supplementary Diagrams

22 M-Series Circuit Breaker - Time Delay Curve Delay Curves,4,, 4, 3, 34, 6, 64, 7, 74, 9, 94: Breakers to hold 00% and must trip at 35% of rated current and greater within the time limit shown in this curve. Delay Curves 0, 0, 30: Breakers to hold 00% and must trip at 50% of rated current and greater within the time limit shown in this curve. 3 All Curves: Curve data shown represents breaker response at ambient temperature of 77 F (5 C) with no preloading. Breakers are mounted in standard wall-mount position. 4 The minimum inrush pulse tolerance handling capability is times the rated current on standard delays and 8 times the rated current on high inrush delays. These values are based on a 60 Hz / cycle, 8.33 ms pulse. High inrush delays should be specified for applications with high initial surge currents of short duration, such as switching power supplies, highly capacitive loads and transformer loads. Instantaneous Dual Rated AC/DC Short Short D Medium Medium D4

23 3 * Intentionally left blank

24 Worldwide Headquarters Carling Technologies, Inc. 60 Johnson Avenue Plainville, CT 0606 Phone: (860) Fax: (860) East Region Sales Office, CT Midwest Region Sales Office, IL West Region Sales Office, CA Asia-Pacific Headquarters Carling Technologies, Asia-Pacific Ltd., Kowloon, Hong Kong Int Fax: Int sales@carlingtech.com.hk Shenzhen, China shenzhen@carlingtech.com Shanghai, China shanghai@carlingtech.com Pune, India india@carlingtech.com Kaohsiung, Taiwan taiwan@carlingtech.com Yokohama, Japan japan@carlingtech.com Europe/Middle East/Africa Headquarters Carling Technologies LTD 4 Airport Business Park, Exeter Airport, Clyst Honiton, Exeter, Devon, EX5 UL, UK Int Fax: Int ltd.sales@carlingtech.com GmbH, Germany gmbh@carlingtech.com SAS, France sas@carlingtech.com REV_CB_M_05_03