BL1000. Programming Guide

Transcription

1 Programming Guide BL1000 Important notice Every effort is made to ensure the accuracy of our product information; however, we accept no responsability for errors or omissions including, but not limited to, the implied warranties of merchantability and fi tness for a particular purpose. We shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this material. Specifi cations or version may be subject to change without notice. The actual specifi cation and version are based on the product delivered. Introduction Scanning a series of programming bar code labels can confi gure the scanner. The scanner must be properly powered before programming. During the programming mode, the scanner will acknowledge a good and valid reading with a short beep. It will give long beeps for either an invalid or bad reading. Baracoda - September 2004 Baracoda, Inc. (US i ce) Baracoda SA (Europe i ce: France) 45 Main street - Suite Brooklyn, NY Avenue de l Amiral Lemonnier Marly-Le-Roi Ph: Fx: Ph: Fx: The bluetooth name and Bluetooth registered trademarks are owned by Bluetooth SIG, Inc., and are used by Baracoda under license. The Baracoda names and Baracoda trademarks are own by Baracoda. All specifi cation are subject to change without notice - Non contractual pictures Baracoda - All rights reserved

2 TABLE OF CONTENTS 1 Configuring your scanner 3 2 Device Option Control Bar Codes Return to Factory Default Settings ACK/NAK Protocol Auto Download Data Beep Control Delay Between Bar Codes None* 500ms ETX Suffix Character Enable * LED Control Line Feed Suffix Character STX Prefix Character Symbology Selection Control Bar Codes Enable all symbologies Code Code EAN UPC-A/EAN UPC-E Supplemental Bar Codes AIM Symbol Identifiers Enable * Combine Bar Codes (FWV 1.7.0) Enable * Symbology Options Control Bar Codes Code 9 Options Code39 Stripped Checksum Enable UPC/EAN Options Convert UPC-A codes to EAN-13 codes (FWV 1.8.0) Command Control Bar Codes Clear Device Bar Code Memory Important notice: Every effort is made to ensure the accuracy of our product information; however, we accept no responsibility for errors or omissions including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this material. Specifications or version may be subject to change without notice. The actual specification and version are based on the product delivered. INTRODUCTION Scanning a series of programming bar code labels can configure the scanner. The scanner must be properly powered before programming. During the programming mode, the scanner will acknowledge a good and valid reading with a short beep. It will give long beeps for either an invalid or bad reading.

3 1 Configuring your scanner Setting Baracoda Default Value Acknowledgment protocol AIM code Automatic data download Baud rate 4800 Beep On Code 128 symbology Code 39 checksum Code 39 strip check character Code 39 symbology Combined bar codes Convert UPC-A bar codes to EAN-13 format (FWV 1.8.0) Delay between bar code transmissions (FWV No delay 1.6.0) Standard vs. aggressive scanning (FWV 1.8.0) Standard Download format Compatible EAN-8 symbology ETX enable Expand UPC-E codes Do not expand LED On Linefeed On NCR symbol identifiers STX On Supplemental bar codes Auto-detect Timestamp UPC-A/EAN-13 symbology UPC-E symbology Baracoda - 3 -

4 To use these bar codes to configure the BL1000, print the appropriate page. Then use your scanner to read the appropriate bar code. 2 Device Option Control Bar Codes 2.1 Return to Factory Default Settings 2.2 ACK/NAK Protocol Enable * 2.3 Auto Download Data 2.4 Beep Control 2.5 Delay Between Bar Codes None* 500ms 1100ms 1 600ms Baracoda - 4 -

5 *Factory Default Setting 2.6 ETX Suffix Character Enable * 2.7 LED Control 2.8 Line Feed Suffix Character 2.9 STX Prefix Character Baracoda - 5 -

6 * Factory Default Setting Baracoda - 6 -

7 3 Symbology Selection Control Bar Codes 3.1 Enable all symbologies 3.2 Code Code EAN UPC-A/EAN UPC-E * Factory Default Setting Baracoda - 7 -

8 3.7 Supplemental Bar Codes Auto-Detect Supplemental Codes* Require Supplemental codes Supplemental Codes 3.8 AIM Symbol Identifiers Enable * 3.9 Combine Bar Codes (FWV 1.7.0) Enable * Baracoda - 8 -

9 * Factory Default Setting Baracoda - 9 -

10 4 Symbology Options Control Bar Codes 4.1 Code 9 Options Code39 Checksum Enable Code39 Checksum * (s both Code 39 Checksum options) 4.2 Code39 Stripped Checksum Enable 4.3 UPC/EAN Options Convert UPC-A codes to EAN-13 codes (FWV 1.8.0) Do Not Convert UPC-A codes* # (FWV 1.8.0) Expand UPC-E codes to UPC-A codes Do Not Expand UPC-E codes* 5 Command Control Bar Codes 5.1 Clear Device Bar Code Memory Baracoda

11 * Factory Default Setting Baracoda