2D Image Barcode Scanner Use Manual V1.0

Transcription

1 2D Image Barcode Scanner Use Manual V1.0

2 Contents Chapter 1 Factory Default Factory Default... 3 Chapter 2 Interface RS Baud Rate Parity Check & Stop Bit & Data Bit USB -HID Serial Communication Chapter 3Common Function Settings Scan Mode Settings Beeper-Good Read Settins LED-Good Read Settings Scan Barcode Delay Settings Trigger Timeout Settings Chapter 4 Data Format Settings General Settings Add Prefix Add Suffix Display scanner 'serial number Display the Version Chapter 5 Symbologies D Barcodes Interleaved 2 of 5(Default ) China Post(Hong Kong)(Default ) Matrix 2 of 5(Default ) Codabar(Default )

3 1.5 MSI(Plessey)(Default ) Code 128(Default ) Code 39(Default ) Code 93(Default ) Standard(IATA,Airline) 2 of 5(two-bar start/stop)(default ) Industrial 2 of 5 (three-bar start/stop)(default ) Gs1 DataBar (RSS)(Default ) Telepen(Default ) Trioptic Code(Default ) UPC-A/EAN13(Default ) Code 11(Default ) D Barcode QR(Default ) Data Matrix(Default ) PDF417(Default ) Aztec(Default ) Hanxin(Default )

4 Chapter 1 Factory Default 1. Factory Default Scanning the following barcode can restore the engine to the factory defaults: Factor Default 3

5 Chapte 2 Interface 6266L provides a RS-232 interface and a USB interface to communicate with the host device. The host devicecan judges it is USB interface or RS-232 interface automatically.the host device can receive and send data via the interface,and settings the 2D scanner 1. RS-232 Interface To ensure smooth communication and accuracy of data, you need to set communication parameters(including baud rate, parity check, data bit and stop bit) to match the host device Default serial communication parameters are listed below: parameter Serial Communication Baud Rate Default Standard RS-232 Parity Check None Data Bits 8 Stop Bits 1 Hardware Flow Control None 1.1 Baud Rate:

6 Parity Check & Data Bit & Stop Bit : None,7,1 None,7,2 None,8,1 Even,7,1 Even,7,2 Even,8,1 5

7 Odd,7,1 Odd,7,2 Odd,8,1 2. USB Interface With a usb cable, the scanner can work as the USB HID-KB mode and USB-COM mode USB HID-KB USB-COM 6

8 3 Serial command Format Consumer s command format: \x02\x11\x03xxxxxx. Serial Command Trigger Trigger push command: Trigger release command: \x02p\x03 \x02r\x03 7

9 Chapter 3Common Function Settings 1. Scan Mode Settings Manual:Press the trigger key to decode barcodes: 2. Beeper-Good Read Settings Good Read Beeper Good Read Beeper 8

10 3. LED-Good Read Settings Good Read LED Good Read LED 4. Scan delay settings: When scan a barcode succeed,it will delay for the designated time to decode the next barcode.default is 0ms. delay 0ms delay 250ms delay 750ms delay 1250ms 9

11 5. Trigger Timeout Settings: Trigger Timeout settings,default Timeout is 30s 30s(Default) 10s 2s 10

12 Chapter 4 Data Format Settings 1. General Settings Add/Delete some general settings: Delete all added Enter-line Enter Line Tab Star(*) 11

13 2. Add Prefix: Prefix Prefix Suffix content added: Format:^3+PREFIX+content need added+(.) example: 3. Suffix Added: Suffix Suffix 12

14 Suffix content added: Format:^3+SUFFIX+content need added+(.) example: 4. Display scanner 'serial number Scan the barcode below can display the serial number of scanner: serial number 5. Display the Version Scan the barcode can display the Version of the sanner: Version 13

15 Chapter 5 Symbologies 1. 1D Barcodes 1.1 Interleaved 2 of 5( Default ) 1.2 China Post(Hong Kong) Default ) 1.3 Matrix 2 of 5( Default ) 14

16 1.4 Codabar( Default ) 1.5 MSI(Plessey)( Default ) 1.6 Code 128( Default ) 1.7 Code 39( Default ) 15

17 1.8 Code 93( Default ) 1.9 Standard(IATA,Airline) 2 of 5(two-bar start/stop) ( Default ) 1.10 Industrial 2 of 5 (three-bar start/stop)( Default ) 1.11 GS1 DataBar (RSS) ( Default ) 16

18 1.12 Telepen( Default ) 1.13 Trioptic Code( Default ) 1.14 UPC-A/EAN13( Default ) 1.15 Code 11( Default ) 17

19 2.2D Barcode 2.1 QR(Default ) 2.2 Data Matrix( Default ) 2.3 PDF417( Default ) 18

20 2.4 Aztec(Default ) 2.5 Hanxin(Default ) 19