EE 1315 DIGITAL LOGIC LAB EE Dept, UMD
|
|
|
- Alexia Potter
- 5 years ago
- Views:
Transcription
1 EE 1315 DIGITAL LOGIC LAB EE Dept, UMD EXPERIMENT # 1: Logic building blocks The main objective of this experiment is to let you familiarize with the lab equipment and learn about the operation of the fundamental combinational logic elements, AND, OR, NAND, and NOR gates. You will also familiarize with the Field Programmable Gate Array (FPGA) prototyping board (Nexys-2) and the Xilinx software development environment that will be used for future experiments. You will also learn how to use the Xilinx ISE development environment and how to download the bit stream to the Digilent Nexys-2 board. Please note: 1) It is necessary for this and all subsequent labs that a flash drive be used to save your lab projects. It is suggested that a folder on your flash drive be created for the sole use of this lab and all projects for this semester be saved to that folder. 2) Steps 9-15 will be conducted every time that a project is downloaded to the FPGA. It may be useful to keep a copy of those instructions available to reference for a few weeks until you are used to programming the FPGA board. When developing with Xilinx ISE, some important information about the device being used (the prototype board) must be known. Look at the chip in the center of the board at your lab station (the FPGA chip). The information on the chip denotes the family, device, and package. Please find this information now. Family: Spartan 3E Device: XC3S500E Package: FG320 Step-by-Step Instruction You will now use the Xilinx ISE schematic tool to develop the four logic gates needed for this experiment. Step 1: Open the Xilinx ISE by clicking on the shortcut on the desktop. Step 2: Create a new project by choosing File->New Project. Give the project a name such as lab 1 (a more descriptive name could be used). The folder where the project is to be saved can also be chosen (somewhere on you flash drive). Click next. Step 3: A new project wizard screen will appear. Enter the values for the family, device, and package that are provided above. Leave the other values unchanged. Click next and then click finish on the following window.
2 Step 4: Right click on the device (can be seen highlighted here: ) and choose new source. In the window that appears, select the schematic type and give it a name. Click next and then finish. Step 5: You will then be presented with the screen seen in figure 1. Take a moment to mouse over the tools on the left of the lab1.sch and note their function. Click on the Add Symbol button. This will allow you to add a gate to your schematic. Figure 1: view of empty schematic lab1.sch Step 6: Notice to the right of the schematic area a symbol dialogue has appeared. Select Logic under the category. The lower dialogue now shows the gates available in the logic category. Start with a two input AND gate. Find the and2 and then click it to select (to speed up the selection, the symbol filter text box can be used to limit the choices in the lower window). Step 7: Drag your cursor over the schematic area. Notice there is now an AND gate following your cursor. Click to place it on the schematic. To place additional AND gates on the schematic, keep clicking. To stop placing AND gates press esc. Repeat this process to place one two input OR, NOR, and NAND (or2, nor2, and nand2 respectively). Step 8: It may be beneficial to zoom in closer to the gates that were just placed on the schematic, do this by using the zoom tools at the top of the schematic. Place I/O markers using the I/O tool. Place one marker on the output of each gate and one marker on each of the inputs of the gates. Each I/O marker can be renamed by right-clicking on it. Rename the output of the OR gate to z1, the output of the NOR gate to z2, the AND gate to z3, and the NAND gate to z4. Similarly rename one input of each gate to x and the other to y. You will get a warning window when you attempt to name a port with the same name as another. Xilinx will ask if you want to merge the ports. By selecting yes, it is like connecting a wire to the two terminals. Select yes for this lab. Your schematic should look similar to figure 2.
3 Figure 2: completed schematic Step 9: You will now generate the binary file and use it to program the FPGA board. Navigate to and expand the User Constraints option in the Design Tab (seen in figure 3). Double click on the I/O Pin Planning (PlanAhdead)-Pre-Synthesis item. A window indicating a User Constraint File (UCF) must be created will appear. Click yes. Figure 3: User Constraints Figure 4: I/O Port Menu Step 10: A new program (RTL Design) will start (be patient). Navigate to the scalar ports menu in the I/O Ports tab. This can be seen in figure 4. Select x and set the site to G18. Click Apply. Continue by setting y to H18, z1 to J14, z2 to J15, z3 to K15, and z4 to K14. The Ports should be defined as seen in figure 5. If everything looks correct click File- >Save Project. Figure 5: Ports with assigned locations Note: In future labs a table as seen in figure 5a will be provided to aid in assigning Scalar Ports to the proper Site on the board.
4 Inputs Outputs Scalar Port X Y Z1 Z2 Z3 Z4 Site G18 H18 J14 J15 K15 K14 I/O SW0 SW1 LD0 LD1 LD2 LD3 Figure 5a: Scalar Port assignment table Step 11: Navigate back to the Xilinx ISE. Under the User Constraints item you just expanded, you will find Synthesize-XST, double click or right click and select run. Now double click the Implement Design found under the Synthesize-XST. It is usual for these operations to take some time. If the operations are successful, you will see green check marks appear next to the items. If a red X appears next to either of the items, there was an error, please let your TA know. Step 12: The clock needs to be set before generating the final bit file. Right click on Generate Programming File and select Process Properties. Select Startup Options and change the FPGA-Start-Up Clock to JTAG Clock as seen in figure 6. Click Apply and OK. Figure 6: Setting the JTAG Clock Step 13: Now double click Generate Programming File. If a green check mark appears, you have successfully generated a bit file to program the FPGA with. This file will automatically be saved in the directory where your project is saved. Step 14: Make sure that the Nexsys-2 board is turned ON. Double click on the Adept icon on the desktop. It should show the window seen in figure 7. Note that Adept automatically recognizes the board. If an error is received, check you connections and click Initialize Chain to attempt to re-connect to the board.
5 Figure 7: Adept window Step 15: Click the Browse... button on the FPGA row and find the bit file you generated (lab1.bit in this case). Click the Program button. A progress bar should grow at the bottom of the window. When the message programming successful appears, the FPGA has been successfully programmed.
6 EXPERIMENT #1 RESULTS (Print this page and bring to lab for TA to sign) The FPGA has now been configured to see a down slide switch as a 0 and an up slide switch as a 1. In addition the outputs are seen by the LEDs above the slide switches with an off state indicating a 0 and an on state indicating a 1. This can be seen in Figure 8. Please show the TA the working circuit and complete the table and questions below. Witnessed by : Figure 8: I/O for lab #1 Date Recorded Truth Table x y z1 (OR) z2 (NOR) z3 (AND) z4 (NAND) IC#: IC#: IC#: IC#: Which pairs of gates have inverting relations according to the truth table above? 2. Write an algebraic equation for each type of gate using the inputs x and y (refer to the web pages of the pin-outs, or textbook, or ask TA) OR: NOR: AND: NAND:
ECE 4305 Computer Architecture Lab #1
ECE 4305 Computer Architecture Lab #1 The objective of this lab is for students to familiarize with the FPGA prototyping system board (Nexys-2) and the Xilinx software development environment that will
Revision: February 27, E Main Suite D Pullman, WA (509) Voice and Fax
Xilinx ISE WebPACK Schematic Capture Tutorial Revision: February 27, 2010 215 E Main Suite D Pullman, WA 99163 (509) 334 6306 Voice and Fax Overview This tutorial provides instruction for using the Xilinx
Getting started with the Xilinx Project Navigator and the Digilent BASYS 2 board.
Getting started with the Xilinx Project Navigator and the Digilent BASYS 2 board. This lab is based on: Xilinx Project Navigator, Release Version 14.6 Digilent Adept System Rev 2.7, Runtime Rev 2.16 Digilent
EE 1315: DIGITAL LOGIC LAB EE Dept, UMD
EXPERIMENT # 7: Basic Latches EE 1315: DIGITAL LOGIC LAB EE Dept, UMD Latches are primitive memory elements of sequential circuits that are used in building simple noise filtering circuits and flip-flops.
and 32 bit for 32 bit. If you don t pay attention to this, there will be unexpected behavior in the ISE software and thing may not work properly!
This tutorial will show you how to: Part I: Set up a new project in ISE 14.7 Part II: Implement a function using Schematics Part III: Simulate the schematic circuit using ISim Part IV: Constraint, Synthesize,
Xilinx Tutorial Basic Walk-through
Introduction to Digital Logic Design with FPGA s: Digital logic circuits form the basis of all digital electronic devices. FPGAs (Field Programmable Gate Array) are large programmable digital electronic
Circuit design with configurable devices (FPGA)
1 Material Circuit design with configurable devices (FPGA) Computer with Xilinx's ISE software installed. Digilent's Basys2 prototype board and documentation. Sample design files (lab kit). Files and documents
Nexys 2/3 board tutorial (Decoder, ISE 13.2) Jim Duckworth, August 2011, WPI. (updated March 2012 to include Nexys2 board)
Nexys 2/3 board tutorial (Decoder, ISE 13.2) Jim Duckworth, August 2011, WPI. (updated March 2012 to include Nexys2 board) Note: you will need the Xilinx ISE Webpack installed on your computer (or you
To practice combinational logic on Logisim and Xilinx ISE tools. ...
ENGG1203: Introduction to Electrical and Electronic Engineering Second Semester, 2017 18 Lab 1 Objective: To practice combinational logic on Logisim and Xilinx ISE tools. 1 Find your lab partner You will
University of Hawaii EE 361L. Getting Started with Spartan 3E Digilent Basys2 Board. Lab 4.1
University of Hawaii EE 361L Getting Started with Spartan 3E Digilent Basys2 Board Lab 4.1 I. Test Basys2 Board Attach the Basys2 board to the PC or laptop with the USB connector. Make sure the blue jumper
The Alarm System: The alarm system to be designed has the following inputs.
1 Introduction In this lab you will use the Xilinx CAD tools to complete the design of a simple home alarm system containing sensors for that indicate whether the Windows, Door, and Garage are secure.
Nexys 2 board tutorial (Decoder, ISE 12.2) Jim Duckworth, August 2010, WPI. Digilent Adept Programming Steps added by Zoe (Zhu Fu)
Nexys 2 board tutorial (Decoder, ISE 12.2) Jim Duckworth, August 2010, WPI. Digilent Adept Programming Steps added by Zoe (Zhu Fu) Note: you will need the Xlinx ISE Webpack installed on your compuer (or
TLL5000 Electronic System Design Base Module
TLL5000 Electronic System Design Base Module The Learning Labs, Inc. Copyright 2007 Manual Revision 2007.12.28 1 Copyright 2007 The Learning Labs, Inc. Copyright Notice The Learning Labs, Inc. ( TLL )
TLL5000 Electronic System Design Base Module. Getting Started Guide, Ver 3.4
TLL5000 Electronic System Design Base Module Getting Started Guide, Ver 3.4 COPYRIGHT NOTICE The Learning Labs, Inc. ( TLL ) All rights reserved, 2008 Reproduction in any form without permission is prohibited.
Revision: February 27, E Main Suite D Pullman, WA (509) Voice and Fax
Xilinx ISE WebPACK VHDL Tutorial Revision: February 27, 2010 215 E Main Suite D Pullman, WA 99163 (509) 334 6306 Voice and Fax Overview This tutorial provides simple instruction for using the Xilinx ISE
Lab 6: Intro to FPGAs
Lab 6: Intro to FPGAs UC Davis Physics 116B Rev 2/22/2018 There s a saying when dealing with complex electronic systems: If you can make the LED blink, you re 90% of the way there., so in this lab you
Banks, Jasmine Elizabeth (2011) The Spartan 3E Tutorial 1 : Introduction to FPGA Programming, Version 1.0. [Tutorial Programme]
![Banks, Jasmine Elizabeth (2011) The Spartan 3E Tutorial 1 : Introduction to FPGA Programming, Version 1.0. [Tutorial Programme]](/thumbs/75/72381729.jpg "Banks, Jasmine Elizabeth (2011) The Spartan 3E Tutorial 1 : Introduction to FPGA Programming, Version 1.0. [Tutorial Programme]")
QUT Digital Repository: http://eprints.qut.edu.au/ This is the author version published as: This is the accepted version of this article. To be published as : This is the author s version published as:
Tutorial: ISE 12.2 and the Spartan3e Board v August 2010
Tutorial: ISE 12.2 and the Spartan3e Board v12.2.1 August 2010 This tutorial will show you how to: Use a combination of schematics and Verilog to specify a design Simulate that design Define pin constraints
Lab 1: Introduction to Verilog HDL and the Xilinx ISE
EE 231-1 - Fall 2016 Lab 1: Introduction to Verilog HDL and the Xilinx ISE Introduction In this lab simple circuits will be designed by programming the field-programmable gate array (FPGA). At the end
Logic Implementation on a Xilinx FPGA using VHDL WWU Linux platform assumed. rev 10/25/16
1 Logic Implementation on a Xilinx FPGA using VHDL WWU Linux platform assumed. rev 10/25/16 The following is a general outline of steps (i.e. design flow) used to implement a digital system described with
Xilinx Project Navigator Reference Guide
31 July 2003 Author: David M. Sendek Xilinx Project Navigator Reference Guide Background: This guide provides you with step-by-step procedures in using the Xilinx Project Navigator to perform the following:
ECE 491 Laboratory 1 Introducing FPGA Design with Verilog September 6, 2004
Goals ECE 491 Laboratory 1 Introducing FPGA Design with Verilog September 6, 2004 1. To review the use of Verilog for combinational logic design. 2. To become familiar with using the Xilinx ISE software
EE 367 Logic Design Lab #1 Introduction to Xilinx ISE and the ML40X Eval Board Date: 1/21/09 Due: 1/28/09
EE 367 Logic Design Lab #1 Introduction to Xilinx ISE and the ML40X Eval Board Date: 1/21/09 Due: 1/28/09 Lab Description Today s lab will introduce you to the Xilinx Integrated Software Environment (ISE)
Xilinx ISE8.1 and Spartan-3 Tutorial EE3810
Xilinx ISE8.1 and Spartan-3 Tutorial EE3810 1 Part1) Starting a new project Simple 3-to-8 Decoder Start the Xilinx ISE 8.1i Project Navigator: Select File > New Project in the opened window 2 Select a
Logic Implementation on a Xilinx FPGA using VHDL WWU Linux platform assumed. rev 11/01/17
1 Logic Implementation on a Xilinx FPGA using VHDL WWU Linux platform assumed. rev 11/01/17 The following is a general outline of steps (i.e. design flow) used to implement a digital system described with
Boise State University Digital Systems Laboratory
by S. M. Loo, Arlen Planting Department of Electrical and Computer Engineering Boise State University First Released: Spring 2005 with ISE 6.3i Updated: Fall 2006 with ISE 8.1i Updated: Spring 2009 with
Step 1: Downloading the source files
Introduction: In this lab and in the remainder of the ELEC 2607 labs, you will be using the Xilinx ISE to enter and simulate the designs for your circuits. In labs 3 and 4, you will use ISE to compile
Programmable Logic Design I
Programmable Logic Design I Introduction In labs 11 and 12 you built simple logic circuits on breadboards using TTL logic circuits on 7400 series chips. This process is simple and easy for small circuits.
Tutorial: Working with the Xilinx tools 14.4
Tutorial: Working with the Xilinx tools 14.4 This tutorial will show you how to: Part I: Set up a new project in ISE Part II: Implement a function using Schematics Part III: Implement a function using
CPLD Experiment 4. XOR and XNOR Gates with Applications
CPLD Experiment 4 XOR and XNOR Gates with Applications Based on Xilinx ISE Design Suit 10.1 Department of Electrical & Computer Engineering Florida International University Objectives Materials Examining
CECS LAB 1 Introduction to Xilinx EDA Tools
NAME: DUE DATE: STUDENT ID: POSSIBLE POINTS: 10 COURSE DATE & TIME: OBJECTIVE: To familiarize ourselves with the Xilinx Electronic Design Aid (EDA) Tools. We will simulate a simple 4-to-1 Multiplexor using
Xilinx ISE8.1 and Spartan-3 Tutorial (Prepared by Kahraman Akdemir based on Professor Duckworth's Tutorials updated September 2006)
Xilinx ISE8.1 and Spartan-3 Tutorial (Prepared by Kahraman Akdemir based on Professor Duckworth's Tutorials updated September 2006) 1 Part1) Starting a new project Simple 3-to-8 Decoder Start the Xilinx
Xilinx ISE Synthesis Tutorial
Xilinx ISE Synthesis Tutorial The following tutorial provides a basic description of how to use Xilinx ISE to create a simple 2-input AND gate and synthesize the design onto the Spartan-3E Starter Board
Introduction. About this tutorial. How to use this tutorial
Basic Entry & not About this tutorial This tutorial consists of an introduction to creating simple circuits on an FPGA using a variety of methods. There are two ways to create the circuit: using or by
Building Combinatorial Circuit Using Behavioral Modeling Lab
Building Combinatorial Circuit Using Behavioral Modeling Lab Overview: In this lab you will learn how to model a combinatorial circuit using behavioral modeling style of Verilog HDL. You will model a combinatorial
ANADOLU UNIVERSITY DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING. EEM Digital Systems II
ANADOLU UNIVERSITY DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EEM 334 - Digital Systems II LAB 1 - INTRODUCTION TO XILINX ISE SOFTWARE AND FPGA 1. PURPOSE In this lab, after you learn to use
The board is powered by the USB connection, so to turn it on or off you plug it in or unplug it, respectively.
Lab 1 You may work in pairs or individually on this lab Lab Objectives Learn about the equipment we will be using and how to handle it safely. Learn the basics of using Xilinx ISE to develop hardware designs
ELEC 204 Digital System Design LABORATORY MANUAL
ELEC 204 Digital System Design LABORATORY MANUAL : Introductory Tutorial For Xilinx ISE Foundation v10.1 & Implementing XOR Gate College of Engineering Koç University Important Note: In order to effectively
Tutorial on Quartus II Introduction Using Verilog Code
Tutorial on Quartus II Introduction Using Verilog Code (Version 15) 1 Introduction This tutorial presents an introduction to the Quartus II CAD system. It gives a general overview of a typical CAD flow
Xilinx ISE/WebPack: Introduction to Schematic Capture and Simulation
Xilinx ISE/WebPack: Introduction to Schematic Capture and Simulation Revision: February 7, 2003 Overview This document is intended to assist new entry-level users of the Xilinx ISE/WebPack software. It
Tutorial - Using Xilinx System Generator 14.6 for Co-Simulation on Digilent NEXYS3 (Spartan-6) Board
Tutorial - Using Xilinx System Generator 14.6 for Co-Simulation on Digilent NEXYS3 (Spartan-6) Board Shawki Areibi August 15, 2017 1 Introduction Xilinx System Generator provides a set of Simulink blocks
Tutorial on FPGA Design Flow based on Aldec Active HDL. Ver 1.5
Tutorial on FPGA Design Flow based on Aldec Active HDL Ver 1.5 1 Prepared by Ekawat (Ice) Homsirikamol, Marcin Rogawski, Jeremy Kelly, John Pham, and Dr. Kris Gaj This tutorial assumes that you have basic
1 Discussion. 2 Pre-Lab
CSE 275 Digital Design Lab Lab 3 Implementation of a Combinational Logic Circuit Penn State Erie, The Behrend College Fall Semester 2007 Number of Lab Periods: 1 1 Discussion The purpose of this lab is
Introduction to Nexys 2 board - Detour Signal Lab
1. Synopsis: Introduction to Nexys 2 board - This lab introduces the use of Field Programmable Gate Arrays (FPGA). This lab introduces the Digilent Nexys 2 board and demonstrate FPGA design flow through
PRELAB! Read the entire lab, and complete the prelab questions (Q1- Q3) on the answer sheet before coming to the laboratory.
PRELAB! Read the entire lab, and complete the prelab questions (Q1- Q3) on the answer sheet before coming to the laboratory. 1.0 Objectives In this lab you will get familiar with the concept of using the
4. Verify that HDL is selected as the Top-Level Source Type, and click Next. The New Project Wizard Device Properties page appears.
Working with the GODIL Author: Ruud Baltissen Credits: Michael Randelzhofer, Ed Spittles Date: August 2010 What is it? This document describes a way to get familiar with the Xilinx FPGAs on OHO s Godil,
ECSE-323 Digital System Design. Lab #1 Using the Altera Quartus II Software Fall 2008
1 ECSE-323 Digital System Design Lab #1 Using the Altera Quartus II Software Fall 2008 2 Introduction. In this lab you will learn the basics of the Altera Quartus II FPGA design software through following
Programming Xilinx SPARTAN 3 Board (Simulation through Implementation)
Programming Xilinx SPARTAN 3 Board (Simulation through Implementation) September 2008 Prepared by: Oluwayomi Adamo Class: Project IV University of North Texas FPGA Physical Description 4 1. VGA (HD-15)
University of Florida EEL 3701 Dr. Eric M. Schwartz Madison Emas, TA Department of Electrical & Computer Engineering Revision 1 5-Jun-17
Page 1/14 Example Problem Given the logic equation Y = A*/B + /C, implement this equation using a two input AND gate, a two input OR gate and two inverters under the Quartus environment. Upon completion
Vivado Tutorial. Introduction. Objectives. Procedure. Lab Workbook. Vivado Tutorial
Lab Workbook Introduction This tutorial guides you through the design flow using Xilinx Vivado software to create a simple digital circuit using Verilog HDL. A typical design flow consists of creating
Tutorial: Working with Verilog and the Xilinx FPGA in ISE 9.2i
Tutorial: Working with Verilog and the Xilinx FPGA in ISE 9.2i This tutorial will show you how to: Use Verilog to specify a design Simulate that Verilog design Define pin constraints for the FPGA (.ucf
VIVADO TUTORIAL- TIMING AND POWER ANALYSIS
VIVADO TUTORIAL- TIMING AND POWER ANALYSIS IMPORTING THE PROJECT FROM ISE TO VIVADO Initially for migrating the same project which we did in ISE 14.7 to Vivado 2016.1 you will need to follow the steps
Programmable Logic Design Techniques I
PHY 440 Lab14: Programmable Logic Design Techniques I The design of digital circuits is a multi-step process. It starts with specifications describing what the circuit must do. Defining what a circuit
NOTE: This tutorial contains many large illustrations. Page breaks have been added to keep images on the same page as the step that they represent.
CSE 352 Tutorial # 4 Synthesizing onto an FPGA Objectives This tutorial will walk you through the steps of implementing a design made in Active-HDL onto the Altera Cyclone II FPGA NOTE: This tutorial contains
A B A+B
ECE 25 Lab 2 One-bit adder Design Introduction The goal of this lab is to design a one-bit adder using programmable logic on the BASYS board. Due to the limitations of the chips we have in stock, we need
Programmable Logic Design I
Programmable Logic Design I Read through each section completely before starting so that you have the benefit of all the directions. Put on a grounded wrist strap (cf. Getting Started) before touching
XILINX WebPack -- testing with Nexys2 boards at USC (EE201L)
XILINX WebPack -- testing with Nexys2 boards at USC (EE201L) Gandhi Puvvada 1 Before you start: 1.1 We assume that you have installed WebPACK on your desktop or laptop already. We assume that you have
Xilinx Schematic Entry Tutorial
Overview Xilinx Schematic Entry Tutorial Xilinx ISE Schematic Entry & Modelsim Simulation What is circuit simulation and why is it important? Complex designs, short design cycle Simultaneous system design
Using Synplify Pro, ISE and ModelSim
Using Synplify Pro, ISE and ModelSim VLSI Systems on Chip ET4 351 Rene van Leuken Huib Lincklaen Arriëns Rev. 1.2 The EDA programs that will be used are: For RTL synthesis: Synplicity Synplify Pro For
1. Downloading. 2. Installation and License Acquiring. Xilinx ISE Webpack + Project Setup Instructions
Xilinx ISE Webpack + Project Setup Instructions 1. Downloading The Xilinx tools are free for download from their website and can be installed on your Windowsbased PC s. Go to the following URL: http://www.xilinx.com/support/download/index.htm
Revision: January 28, Henley Court Pullman, WA (509) Voice and Fax
Lab Project 2: Board Verification and Basic Logic Circuits Revision: January 28, 2012 1300 Henley Court Pullman, WA 99163 (509) 334 6306 Voice and Fax STUDENT I am submitting my own work, and I understand
Verilog Design Entry, Synthesis, and Behavioral Simulation
------------------------------------------------------------- PURPOSE - This lab will present a brief overview of a typical design flow and then will start to walk you through some typical tasks and familiarize
Tutorial on FPGA Design Flow based on Xilinx ISE WebPack and ModelSim. ver. 2.0
Tutorial on FPGA Design Flow based on Xilinx ISE WebPack and ModelSim ver. 2.0 Updated: Fall 2013 1 Preparing the Input: Download examples associated with this tutorial posted at http://ece.gmu.edu/tutorials-and-lab-manuals
ELEC 4200 Lab#0 Tutorial
1 ELEC 4200 Lab#0 Tutorial Objectives(1) In this Lab exercise, we will design and implement a 2-to-1 multiplexer (MUX), using Xilinx Vivado tools to create a VHDL model of the design, verify the model,
Tutorial on Quartus II Introduction Using Schematic Designs
Tutorial on Quartus II Introduction Using Schematic Designs (Version 15) 1 Introduction This tutorial presents an introduction to the Quartus II CAD system. It gives a general overview of a typical CAD
UNIVERSITI MALAYSIA PERLIS
UNIVERSITI MALAYSIA PERLIS SCHOOL OF COMPUTER & COMMUNICATIONS ENGINEERING EKT 124 LABORATORY MODULE INTRODUCTION TO QUARTUS II DESIGN SOFTWARE : INTRODUCTION TO QUARTUS II DESIGN SOFTWARE OBJECTIVES To
Digital Circuit Design Using Xilinx ISE Tools
Digital Circuit Design Using Xilinx ISE Tools Poras T. Balsara and Prashant Vallur Table of Contents 1. Introduction 2. Programmable logic devices: FPGA and CPLD 3. Creating a new project in Xilinx Foundation
CSE 591: Advanced Hardware Design and Verification (2012 Spring) LAB #0
Lab 0: Tutorial on Xilinx Project Navigator & ALDEC s Active-HDL Simulator CSE 591: Advanced Hardware Design and Verification Assigned: 01/05/2011 Due: 01/19/2011 Table of Contents 1 Overview... 2 1.1
Design a three-input, two-output sequential digital circuit which functions as a digital locking mechanism. LOCK ALARM
Department of Computing Course 112 Hardware First Year Laboratory Assignment Dates for the session 2005-2006: Hand out Date: 10 th January 2006 Hand in deadline (electronic and written report): 17.00 Monday
FPGA Introductory Tutorial: Part 1
FPGA Introductory Tutorial: Part 1 This tutorial is designed to assist in learning the basics of the Altera Quartus II v9.0 software. Part 1 of the tutorial will cover the basics of creating a Project,
EXPERIMENT 1. INTRODUCTION TO ALTERA
EXPERIMENT 1. INTRODUCTION TO ALTERA I. Introduction I.I Objectives In this experiment, you will learn computer aided digital design and verification of it using Field Programmable Gate Arrays (FPGA).
Tutorial on FPGA Design Flow based on Xilinx ISE Webpack andisim. ver. 1.0
Tutorial on FPGA Design Flow based on Xilinx ISE Webpack andisim ver. 1.0 1 Prepared by Malik Umar Sharif and Dr. Kris Gaj The example codes used in this tutorial can be obtained from http://ece.gmu.edu/coursewebpages/ece/ece448/s11/labs/448_lab3.htm
RTL and Technology Schematic Viewers Tutorial. UG685 (v13.1) March 1, 2011
RTL and Technology Schematic Viewers Tutorial The information disclosed to you hereunder (the Information ) is provided AS-IS with no warranty of any kind, express or implied. Xilinx does not assume any
SCHEMATIC DESIGN IN QUARTUS
SCHEMATIC DESIGN IN QUARTUS Consider the design of a three-bit prime number detector. Figure 1 shows the block diagram and truth table. The inputs are binary signals A, B, and C while the output is binary
Tutorial on FPGA Design Flow based on Xilinx ISE Webpack and ModelSim. ver. 1.5
Tutorial on FPGA Design Flow based on Xilinx ISE Webpack and ModelSim ver. 1.5 1 Prepared by Marcin Rogawski, Ekawat (Ice) Homsirikamol, Kishore Kumar Surapathi and Dr. Kris Gaj The example codes used
ECE 3610 Microprocessing Systems Lab #1 Verilog Design of the TOC Using Quartus II
ECE 3610 Microprocessing Systems Lab #1 Verilog Design of the TOC Using Quartus II This lab manual presents an introduction to the Quartus II Computer Aided Design (CAD) system. This manual gives step-by-step
EE 231 Fall Lab 1: Introduction to Verilog HDL and Altera IDE
Lab 1: Introduction to Verilog HDL and Altera IDE Introduction In this lab you will design simple circuits by programming the Field-Programmable Gate Array (FPGA). At the end of the lab you should be able
Implementing a Verilog design into the UWEE CPLD Development Board Using Xilinx s ISE 7.1i Software: A Tutorial
Implementing a Verilog design into the UWEE CPLD Development Board Using Xilinx s ISE 7.1i Software: A Tutorial Revision 0 By: Evan Gander Materials: The following are required in order to complete this
Guide ISE14. ISE 14.2 (Xilinx) Designflow 1/12
Guide ISE14 ISE 14.2 (Xilinx) Designflow 1/12 Inhaltsverzeichnis 1. Create a Project 3 2. Select a Device 4 3. Add the Sourcecodes 5 4. File for the Pinning 6 5. Synthesis 7 6. Implementation 8 7. Programming
Chip Design with FPGA Design Tools
Chip Design with FPGA Design Tools Intern: Supervisor: Antoine Vazquez Janusz Zalewski Florida Gulf Coast University Fort Myers, FL 33928 V1.9, August 28 th. Page 1 1. Introduction FPGA is abbreviation
Laboratory #Intro to Xilinx ISE and CR-2 Kit ECE 332
Name: G Number: 1 Introduction Laboratory #Intro to Xilinx ISE and CR-2 Kit ECE 332 The purpose of this laboratory is to introduce the design tools used in ECE 332 lab. In this lab you will learn about
Contents. Appendix B HDL Entry Tutorial 2 Page 1 of 14
Appendix B HDL Entry Tutorial 2 Page 1 of 14 Contents Appendix B HDL Entry Tutorial 2...2 B.1 Getting Started...2 B.1.1 Preparing a Folder for the Project...2 B.1.2 Starting Quartus II...2 B.1.3 Creating
Tutorial on FPGA Design Flow based on Aldec Active HDL. ver 1.7
Tutorial on FPGA Design Flow based on Aldec Active HDL ver 1.7 Fall 2012 1 Prepared by Ekawat (Ice) Homsirikamol, Marcin Rogawski, Jeremy Kelly, Kishore Kumar Surapathi, Ambarish Vyas, Malik Umar Sharif
Tutorial on FPGA Design Flow based on Aldec Active HDL. Ver 1.5
Tutorial on FPGA Design Flow based on Aldec Active HDL Ver 1.5 1 Prepared by Ekawat (Ice) Homsirikamol, Marcin Rogawski, Jeremy Kelly, Kishore Kumar Surapathi and Dr. Kris Gaj This tutorial assumes that
After opening the Programs> Xilinx ISE 8.2i > Project Navigator, you will come to this screen as start-up.
After opening the Programs> Xilinx ISE 8.2i > Project Navigator, you will come to this screen as start-up. Start with a new project. Enter a project name and be sure to select Schematic as the Top-Level
Experiment 3. Digital Circuit Prototyping Using FPGAs
Experiment 3. Digital Circuit Prototyping Using FPGAs Masud ul Hasan Muhammad Elrabaa Ahmad Khayyat Version 151, 11 September 2015 Table of Contents 1. Objectives 2. Materials Required 3. Background 3.1.
University of California at Berkeley College of Engineering Department of Electrical Engineering and Computer Science. EECS 150 Spring 2000
University of California at Berkeley College of Engineering Department of Electrical Engineering and Computer Science EECS 150 Spring 2000 Lab 1 Introduction to Xilinx Design Software 1 Objectives In this
Tutorial on FPGA Design Flow based on Aldec Active HDL. ver 1.6
Tutorial on FPGA Design Flow based on Aldec Active HDL ver 1.6 Fall 2011 1 Prepared by Ekawat (Ice) Homsirikamol, Marcin Rogawski, Jeremy Kelly, Kishore Kumar Surapathi, Ambarish Vyas, Umar Sharif and
Laboratory of Digital Circuits Design: Design, Implementation and Simulation of Digital Circuits Using Programmable Devices
Internet Engineering Dr. Jarosław Sugier Laboratory of Digital Circuits Design: Design, Implementation and Simulation of Digital Circuits Using Programmable Devices This document presents software packages
EMT1250 LABORATORY EXPERIMENT. EXPERIMENT # 6: Quartus II Tutorial and Practice. Name: Date:
EXPERIMENT # 6: Quartus II Tutorial and Practice Name: Date: Equipment/Parts Needed: Quartus II R Web Edition V9.1 SP2 software by Altera Corporation USB drive to save your files Objective: Learn how to
MANUAL XILINX ISE PROJECT NAVIGATOR
Hochschule für Angewandte Wissenschaften Hamburg University of Applied Sciences Department of Electrical Engineering and Computer Sciences MANUAL XILINX ISE PROJECT NAVIGATOR AND MODELSIM Design Flow for
PlanAhead Software Tutorial
PlanAhead Software Tutorial RTL Design and IP Generation The information disclosed to you hereunder (the Information ) is provided AS-IS with no warranty of any kind, express or implied. Xilinx does not
University of Florida EEL 3701 Dr. Eric M. Schwartz Department of Electrical & Computer Engineering Revision 0 12-Jun-16
Page 1/14 Quartus Tutorial with Basic Graphical Gate Entry and Simulation Example Problem Given the logic equation Y = A*/B + /C, implement this equation using a two input AND gate, a two input OR gate
Copyright 2011 R.S.R. Electronics, Inc. All rights reserved. 04/11. Ver. 1.0web
For XILINX WebPack Copyright 2011 R.S.R. Electronics, Inc. All rights reserved. 04/11 Ver. 1.0web 1 Table of Contents 1.0 INTRODUCTION...3 2.0 GENERAL DESCRIPTION...5 3.0 BRIEF DESCRIPTION Of PLDT-3 BOARD...6
Quartus II Introduction Using Verilog Design
Quartus II Introduction Using Verilog Design This tutorial presents an introduction to the Quartus R II CAD system. It gives a general overview of a typical CAD flow for designing circuits that are implemented
LABORATORY # 6 * L A B M A N U A L. Datapath Components - Adders
Department of Electrical Engineering University of California Riverside Laboratory #6 EE 120 A LABORATORY # 6 * L A B M A N U A L Datapath Components - Adders * EE and CE students must attempt also to
University of California at Berkeley College of Engineering Department of Electrical Engineering and Computer Science
University of California at Berkeley College of Engineering Department of Electrical Engineering and Computer Science EECS 150 Fall 2000 Original Lab By: J.Wawrzynek and N. Weaver Edited by B. Choi, R.
Lab 1: FPGA Physical Layout
Lab 1: FPGA Physical Layout University of California, Berkeley Department of Electrical Engineering and Computer Sciences EECS150 Components and Design Techniques for Digital Systems John Wawrzynek, James
Engineering 1630 Fall Simulating XC9572XL s on the ENGN1630 CPLD-II Board
Engineering 1630 Fall 2016 Simulating XC9572XL s on the ENGN1630 CPLD-II Board You will use the Aldec Active-HDL software for the required timing simulation of the XC9572XL CPLD programmable logic chips
Lab 3: Xilinx PicoBlaze Flow Lab Targeting Spartan-3E Starter Kit
Lab 3: Xilinx PicoBlaze Flow Lab Targeting Spartan-3E Starter Kit Xilinx PicoBlaze Flow Demo Lab www.xilinx.com 1-1 Create a New Project Step 1 Create a new project targeting the Spartan-3E device that