User Manual. 8 TFT/4CH MJPEG Media DVR LR804. 4ch Media LCD DVR. User Manual

Transcription

1 User Manual 8 TFT/4CH MJPEG Media DVR LR804 4ch Media LCD DVR User Manual 1 1

2 Revision Revision Update Modified Content Editor V /07/19 Draft Roland V /08/24 Primary Release Roland 2 2

3 Installation & Safeguards INSTALLATION & SAFEGUARDS 1. All the safety and operating instructions should be read before the DVR is operated. 2. Keep and follow all instructions. 3. Heed all warnings. 4. Clean only with dry cloth. 5. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 6. Unplug this apparatus during lightning storms or when it is unused for long periods of time. Environment Condition for Installation 1. To prevent electric shock or other hazards, do not expose the DVR to rain, moisture, or dust. 2. Place this DVR in a well-ventilated place and do not place heat-generating objects on it. 3. This unit should not be located in an area where it is likely to be subjected to mechanical shocks. Before You Start 1. Ensure the power switch is off before starting to operate the DVR. 2. Do not attempt to open or remove the cabinet. That may expose you to dangerous voltage or other hazards. 3. Installation ought to be performed by qualified service specialists. 4. The power resource for the DVR must accord with the manufacturer s instruction label on the power supply. And please use the power supply included with the unit to energize the DVR. Notice 1. In initial operation, you must set TIME/DATE SETUP to have a correct recording time/date. 2. Format the HDD (MAIN MENU CONFIGURATION TIME/DATE) after connecting it with the DVR. If you don t follow the procedure, this will cause the DVR not to record images or save setting values. Additionally, even if there are recorded images inside, you are unable to search them. 3. To have sufficient DVR memory, you are recommended to use a large-capacity HDD. 4. You must set RECORD and SCHEDULE SETUP both in the menu of RECORD (MAIN MENU RECORD SCHEDULE SETUP) to enable the DVR to record the way you need. The recording type default is continuous mode. 3 3

4 Installation & Safeguards WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove the front or back covers. No user-serviceable parts inside. Refer servicing to qualified service personnel only. The lightning flash with arrow-head within a triangle is intended to inform the user that parts inside the product are a risk of electric shock. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are explained. 4 4

5 Table of Contents CHAP.1 FEATURES & PACKAGE CONTENTS FEATURES PACKAGE CONTENTS...9 CHAP.2 OUTLOOK FRONT REAR...11 CHAP.3 INSTALLATION INSTALLATION CONFIGURATION DETAILED INSTALLATION HDD CAMERA MONITOR / SPOT POWER OTHER EXTERNAL DEVICES...16 CHAP.4 DVR OPERATION MOUSE CONTROL DVR LOG-IN (OPEN MAIN MENU) FORMAT THE HDD TIME/DATE SETTING LIVE RECORDING MODE PLAYBACK SEARCH SEQUENCE ZOOM IN PIP (PICTURE IN PICTURE) PTZ (PAN/ TILT/ ZOOM) SCHEDULE RECORD FULL / 4-SPLIT SCREEN MAIN MENU DISPLAY SETUP...23 (1) SCREEN DISPLAY...23 (2) OSD SETUP

6 Table of Contents 2. RECORD...24 (1) RECORD SETUP...24 (2) SCHEDULE SETUP...24 (2) SCHEDULE SETUP CONFIGURATION...26 (1) HDD MANAGEMENT...26 (2) CAMERA SETUP...27 (3) MOTION SETUP...27 (4) ALARM SETUP...28 (5) INTERVAL SETUP...28 (6) TIME/DATE SETUP...29 (7) PASSWORD SETUP...29 (8) BUZZER SETUP EXTERNAL DEVICE...30 (1) TCP/IP SETUP...30 (2). PAN/TILT SETUP...31 (3) SPOT SETUP BACK-UP FIRMWARE UPGRADE LANGUAGE...32 CHAP.5 NETWORK SETUP DVR NETWORK CONFIGURATION STATIC IP DYNAMIC IP DYNAMIC IP OF PPPOE (DSL)...36 CHAP.6 DVR PROGRAM SETUP REGISTERING DVR FOR DDNS (DDNS WEB-SERVER) DDNS SETUP IN DVR DVR WEB VIEWER (VIA IE) DVR BACKUP PLAYER (VIA IE) WEB NETWORK BACKUP (VIA IE) DVR REMOTE VIEWER MAIN INTERFACE IP/PORT SETTING DDNS SETTING

7 Table of Contents 4. PTZ/SAVE SETTING PLAYBACK INTERFACE THROUGH THE DVR REMOTE VIEWER BACKUP CD PLAYER...55 CHAP.7 MEDIA PLAYER ( THIS CHAPTER IS FOR LR-804J02 ONLY) REMOTE CONTROLLER...57 FUNCTION OVERVIEW OF BUTTONS SUPPORTED MEDIA TYPE/ PLAYBACK FORMATS INTRODUCTION OF ON-SCREEN DISPLAYS SETUP MENU...61 APPENDIX Ⅰ. SPECIFICATION...63 Ⅱ. LIST OF ALL SUPPORTED HDDS...65 Ⅲ. DIMENSIONS...65 Ⅳ. TABLE OF HDD RECORDING TIME (FOR A 250 GB HDD)...66 Ⅴ. MENU PARAMETERS TABLE

8 CHAP.1 Features & Package Contents CHAP.1 Features & Package Contents 1-1. Features Live Display Real-time display for 4 cameras Auto sequence PIP (picture in picture) Digital zoom of display Simple playback modes Easy PTZ camera control Record Variable record resolution (For higher picture quality or recording speed) Efficient image quality setup of 5 levels Schedule recording Event recording for alarms and motion detection Network To monitors or searches using the remote viewer via the network Playback To search and replay by the percent, date/time, or events of the recorded video data Multiple forward playback speeds (X 2,4,8,16,32 fast playback; X 1/16,1/8,1/4,1/2 slow playback) Multiple backward playback speeds (X 2,4,8,16,32 fast playback; X 1/16,1/8,1/4,1/2 slow playback) Data Backup Simple backup using an USB mass-storage device Remote viewer backup in the format of AVI or JPEG Supports a high-capacity HDD. Media Playing Supports music playing (MP3), photo playing, and movie playing Supports SD cards for flash media files. ( For LR-804J02 only) Others Supports SPOT monitor. PAL/NTSC auto detection 8 8

9 CHAP.1 Features & Package Contents 1-2. Package Contents 2. Power Cable 1. Main Unit 3. Power Adapter 4. Quick Guide 5. Software CD 6. Mouse 7 Remote Controller 8. Screws (X 4) 9. Audio Cable 10. BNC Adapter No. Package Contents Description 1 DVR Main Unit Stand-alone Digital Video Recorder with Media Player 2 Power Cable AC Power Supply to Adapter for DC 12V Power 3 Power Adapter DC 12V Power Supply 4 Quick Guide (Manual) Instructs users how to operate the Media DVR. 5 Software CD Contains: (1) manuals (English/Chinese) (2) quick guide (English) (3) software tools (4) README. 6 Mouse Controls all functions of the Media DVR. 7 Remote Controller IR Remote Controller for Media Player 8 Screws (X4) Fix an HDD to the HDD drawer. 9 Audio Cable Connects left and speakers. 10 BNC Adapter BNC-to-RCA Video Adapter ( Item 9 and 10 are for LR-804J02 only.) 9 9

10 CHAP.2 Outlook CHAP.2 Outlook 2-1. Front No. Items Function 1 8 LCD Display Displays images. 2 Speakers Gives sounds. 3 Receiver (IR Port) Receives IR signals out of the remote controller. 4 Power LED Gives red light when the power is on. 5 Control Buttons Control the OSD menu of the LCD. DISPLAY SOURCE MENU UP DOWN LCD Power Switch (On / Off) Video Source Switch (DVR / MEDIA) Open OSD menu for LCD adjustment. Move up. / Increase values or volume. Move down. / Decrease values or volume

11 CHAP.2 Outlook 2-2. Rear No. Items Function 1 Power Switch Media DVR Power Switch (On/Off) 2 MONITOR Connects a monitor (NTSC / PAL). 3 MOUSE Connects a USB mouse. 4 HOST (1) For Backup of DVR Video Images (2) For DVR Firmware Upgrade 5 MEDIA AUDIO OUT Connects a monitor for the Media Player. 6 DC 12 V Connects a DC 12 V / 5A power supply. 7 PS/2 Connects a PS/2 mouse. 8 SPOT Connects a SPOT monitor. 9 CH 1~4 Connect cameras. 10 HDD Drawer For HDD Combination ( (1) The jumper must be master. (2)The HDD is expandable to 500 GB.) 11 ETHERNET Connects the Ethernet. 12 MEDIA VEDIO OUT Connects a monitor for the Media Player. 13 FUNCTION Function Port for External Devices 14 Function Port Note 1~2 For External Devices (eg. Speed Domes) 3~5 For Sirens (Relay Output) 6~10 For Inputs of 4 Alarms 15 Fan Moderates the Media DVR s temperature. 16 RS-232C Allows engineers to debug the DVR s firmware. ( Item 5 and 12 are for LR-804J02 only.) 11 11

12 2-3. Side CHAP.2 Outlook 1 2 No. Items Function 1 DVD Driver For Media Player Only (CD / VCD / DVD) 2 SD Slot For Media Player Only (SD Card / MMC Card) ( Item 1 and 2 are for LR-804J02 only.) 12 12

13 CHAP.3 Installation CHAP.3 Installation 3-1. Installation Configuration 13 13

14 3-2. Detailed Installation 1. HDD 1. Connect the main board with an HDD by an IDE cable plus an HDD power wire. 2. To install the HDD, the jumper setting must be master. 3. Combine the HDD with the HDD drawer by using the 4 screws. 4. Fix the HDD drawer back to the main unit. Panel CHAP.3 Installation DVD Player ( For LR-804J02 only.) CF Card Reader ( For LR-804J02 only.) DVR Main Board Hard Disk NOTE : 1. Please refer to the list of all supported HDDs in the appendix (on the page 65) for information of HDDs compatible with this DVR. 2. To know the maximal recording time for various HDDs, please use the table of HDD recording time (on the pages 66 and 67) as reference. 3. The screws for the HDD are attached in the package. 2. CAMERA DC LEVEL VIDEO V.P DC LENS VIDEO AC24V/DC12 Rear view of CAMERA Rear View of A Camera Connect a camera to a video input (CH1~4) on the rear panel of the DVR

15 CHAP.3 Installation 3. MONITOR (LOOP) / SPOT VIDEO A VIDEO B VIDEO C IN OUT IN OUT IN OUT Rear View of A Monitor Connect the MINOTOR (LOOP) or SPOT video output of the DVR with a video input of a main monitor. NOTE : 1. A monitor combined with the video output jack MONITOR displays the identical images to the DVR s. 2. A monitor combined with the video output jack SPOT sequentially displays the images of each connected channel. 4. POWER Connect the DC plug of the power adapter into the DC input jack of the DVR. Power Supply 15 15

16 CHAP.3 Installation 5. OTHER EXTERNAL DEVICES External Speakers (3) External Display Device (4) (1) (2) PTZ Camera Computer (1) FUNCTION PORT: Siren Alarm Sensors RS 485 D -/+ (Function Pin 1,2): Control external devices such as PTZ cameras. RELAY COM /NC/NO (Function Pin 3~5): Relay output for devices such as sirens. ALARM GROUND (Function Pin 6): Connects the ground wires of the connected alarm sensors. ALARM D1~4 (Function Pin 7~10): Connect alarm sensors. NOTE : 1. The DVR affords multiple sirens. 2. The DVR affords up to 4 PTZ cameras. (2) ETHERNET JACK: For LAN or WAN connection. (3) MEDIA (VIDEO / AUDIO) OUTPUTS: 1. For an external display device. 2. For 2 external loudspeakers. ( For LR-804J02 only.) (4) RS-232C PORT: For engineers to debug the DVR s firmware

17 CHAP.4 DVR Operation CHAP.4 DVR Operation 4-1. Mouse Control No. Mouse Control Functions 1 Left Button (1) Executes. (2) Confirms. (3) Enters. (4) Increases setting values. 2 Right Button (1) Cancels. (2) Recovers. (3) Decreases setting values. 3 Wheel (1) Increases/Decreases setting values. (2) Speeds up/down playback. (3) Zooms in/out in a PTZ mode. NOTE : 1. Some of the items displayed in setting menus are merely listed as indication, which users are unable to select or adjust by the cursor. 2. The background color of a selectable or adjustable item will turn white when a user moves the cursor onto it. A user can interact with it using the buttons or the wheel of a mouse DVR Log-in (Open Main Menu) (1) Move the cursor to the lower right corner on the display. DVR LOG-IN Then, click to log into MAIN MENU. ( DVR LOG-IN USER ID ADMIN MAIN MENU)(2) The message of DVR LOG-IN shows as the right figure. Log in as an administrator (ADMIN), and input the password (PW) composed of up to 8 digits. USER PW ENTER EXIT (3) To exit, click EXIT. ( As for MAIN MENU, refer to the page 23.) NOTE : 1. The USER ID is unchangeable and fixed as an administrator (ADMIN). 2. The password default is none. When logging in for the first time, please straightly click ENTER. 3. If the inputted password matches the one you already set, you will be allowed to enter the MAIN MENU. Contrarily, if an incorrect password is inputted, a message of PW IS NOT CORRECT will show on the display

18 4-3. Format The HDD CHAP.4 DVR Operation When an HDD is combined with the DVR, you must format it initially. You can format this HDD in HDD MANAGEMENT (MAIN MENU CONFIGURATION HDD MANAGEMENT). In this menu, click the FORMAT, and the HDD will be formatted just in seconds. Then, it is enabled to record images. CONFIGURATION HDD MANAGEMENT CAMERA SETUP MOTION SETUP ALARM SETUP INTERVAL SETUP TIME/DATE SETUP PASSWORD SETUP BUZZER SETUP HDD MANAGEMENT MODEL SERIAL BLOCKS SIZE SPEED OVERWRITE FORMAT ESC ESC 4-4. Time/Date Setting If the DVR is operated for the first time, please set the time and date in TIME/DATE SETUP (MAIN MENU CONFIGURATION TIME/DATE SETUP) to accord with the time zone of your location. CONFIGURATION TIME/DATE SETUP HDD MANAGEMENT CAMERA SETUP DATE TIME MOTION SETUP ALARM SETUP INTERVAL SETUP TIME/DATE SETUP PASSWORD SETUP BUZZER SETUP DATE FORMAT HOUR FORMAT MONTH FORMAT DEFAULT ESC ESC 18 18

19 CHAP.4 DVR Operation 4-5. Live Recording Mode ETHERNET Status: Camera Title Current Time/Date Recording Not Recording ( Please refer to the page 22.) Overwriting Status: Overwriting the HDD switched on ( Please refer to the page 26.) ETHERNET Status: Connected Disconnected HDD Status (Recording Mode): Amount of Recorded Data 7) SCHEDULE RECORD Live Recording Toolbar: Alarm Recording 1) PLAYBACK Motion Recording 2) SEARCH Continuous Recording 3) SEQUENCE 4) ZOOM 5) PIP PTZ 6) PTZ 1. PLAYBACK Li R di M d MAIN MENU ( To log onto MAIN MENU, refer to page 17. The details of MAIN MENU are depicted from the page Click to enter the playback mode shown as belown. 23.) PlaybackToolbar: HDD Status (Playback Mode): Amount of Displayed Data Separated Forward Playback x 1/4~1/2 Time Backward Playback Pauses Forward Playback Separated Backward Playback x 1/4~1/2 Time Speed Up Playback x 2, 4, 8, 16, 32 Times Speed Down Playback x 1/16, 1/8, 1/4, 1/2 Times 8) FULL /4-SPLIT SCREEN ( Rolling the wheel also speed up/down playback). SEARCH. Exit Playback 19 19

20 CHAP.4 DVR Operation 2. SEARCH There are 3 approaches for a user to search for the recorded images via SEARCH: Mode PERCENT SEARCH TIME/DATE SEARCH EVENT SEARCH Function Searches by the percentage of total recorded images. Click on the search bar or the percent number and click PLAY, and the DVR will replay from the corresponding recorded image. Searches by time and date. Target a time point between START and END, from which the recorded image will be replayed. Then click PLAY. Searches via the event list that covers all events of motion detection, alarm input, and video loss. The DVR will replay the targeted event from when it occurred. NOTE : Recorded images in different modes (alarm recording, motion recording, and continuous recording) are successively accumulated in chronological order. SEARCH PERCENT SEARCH START 2006 / JUL / 09 PM 01 : 58 : 56 PERCENT SEARCH TIME/DATE SEARCH END 2006 / JUL / 10 PM 11 : 58 : 56 TARGET 2006 / JUL / 09 PM 05 : 58 : 56 EVENT SERACH PERCENT 020% EXIT PLAY ESC TIME/DATE SEARCH START 2006 / JUL / 09 PM 01 : 58 : 56 END 2006 / JUL / 10 PM 11 : 58 : 56 EVENT SEARCH DATE/TIME CHANNEL EVENT ----/--/-- --:--: /--/-- --:--: TARGET 2006 / JUL / 09 PM 05 : 58 : /--/-- --:--: PAGE 000/000 PLAY ESC ESC 20 20

21 CHAP.4 DVR Operation 3. SEQUENCE To make the DVR automatically display channel 1~4 in full-screen sequentially, click. In addition, you can set the channel switching interval in SEQUENCE SCREEN (MAIN MENU CONFIGURATION INTERVAL SETUP SEQUENCE SCREEN). CH04 CH03 CH02 CH01 4. ZOOM IN If you click in the recording mode, live images will be twice enlarged, where you can change the zoomed-in position by sliding the cursor. To exit this mode, click again. 5. PIP (Picture in Picture) Click in the full-screen mode, and you will see a small window in the lower right position. When one of the four channels is displayed on the main screen, others will switch sequentially in this window. You can set their channel switching interval in PIP SCREE (MAIN MENU CONFIGURATION INTERVAL SETUP PIP SCREEN). 6. PTZ (PAN/ TILT/ ZOOM) Click to enter the PTZ mode, where you can pan or tilt a camera toward 8 different directions by clicking the left button. To zoom in or out the camera lens, you can roll the wheel forward or backward with the cursor in the middle of the display. Zoom In Zoom Out 21 21

22 CHAP.4 DVR Operation 7. SCHEDULE RECORD The DVR records as the setting in SCHEDULE SETUP (MAIN MENU RECORD SCHEDULE SETUP).,, or in red indicates the DVR is now recording in the mode of continuous recording, motion recording, or alarm recording. Oppositely, if a recording mode is disabled, its icon will turn white. Record [RED] Stop recording [WHITE] NOTE : In the following conditions, the DVR does not record:1. The HDD is full of recorded images with overwriting off. 2. A user is backuping recorded images via the USB slot. 3. A user is updating a firmware via the USB slot. 4. HDD MANAGEMENT is being opened. 8. FULL / 4-SPLIT SCREEN Full Screen (CH1~4) 1 2 Full Screen (CH1~4) 1. In a full-screen mode, if you click shown on the left half of the toolbar, the screen will be altered to a 4-split screen on the display. 2. In the 4-split mode, click,,, or and the live images of the channel 1, 2, 3, or 4 will be displayed in a full-screen mode

23 CHAP.4 DVR Operation 4-6. Main Menu Click and then input the password, and you can log onto MAIN MENU shown as right: NOTE : 1. For quick search and overview on all parameter ranges. users are highly advised to take advantage of the menu parameters table in the appendix (on the pages 68, 69. and 70). 2. To log onto MAIN MENU, refer to the page 17. MAIN MENU DISPLAY SETUP RECORD CONFIGURATION EXTERNAL DEVICE BACK UP FIRMWARE UPGRADE LANGUAGE ENGLISH 1. DISPLAY SETUP In this configuration, you can adjust the setting of the screen display or the OSD menu. DISPLAY SETUP EXIT VERTICAL POSITION 24 HORIZONTAL POSITION 00 (1) SCREEN DISPLAY VERTICAL POSITION: Alter the position of the main screen vertically. HORIZONTAL POSITON: Alter the position of the main screen horizontally. BORDER ENABLE: Enable or disable the borders for the 4 split screens. BORDER WIDTH: Adjust the border width. BORDER COLOR: Change the border color. NOTE : In each setting menu, click DEFAULT to restore all altered parameters on the menu to the factory default. BORDER ENABLE.ON BORDER WIDTH 01 BORDER COLER GRAY DEFAULT EEC SCREEN DISPLA SCREEN Y DISPLAY OSD SETUP ESC (2) OSD SETUP TOP OSD OFFSET: Alter the position of the upper OSD on the main screen. BOTTOM OSD SETUP: Alter the position of the lower OSD (toolbar) on the main screen. OSD SETUP TOP OSD OFFSET 0 BOTTOM OSD OFFSET 0 DEFAULT EEC 23 23

24 CHAP.4 DVR Operation 2. RECORD RECORD SETUP RECORD This is a premier setting for the DVR to operate, which determines all details concerning recording modes. SCHEDULE SETUP ESC (1) RECORD SETUP CHANNEL: Select a channel to adjust setting. RESOLUTION: Alter the resolution of the recorded images. QUALITY: Alter quality of the recorded images. FRAME RATE: Shift the frame rate of the recorded images. RECORD SETUP CHANNEL CH1 RESOLUTION 352 * 240 QUALITY HIGHEST FRAME RATE 30.0 DEFAULT ALL-DEFAULT ESC NOTE : 1. In each setting menu, click ALL-DEFAULT to restore all changed parameters of the 4 channels on the menu to the factory default. 2. For more transmitted images and longer recording time via IP network, set the resolution as 352x240 and the quality as LOW or NORMAL. 3. Transmitting size of images in the PAL system is a little bigger than that in the NTSC system, but the total recording time for both systems is the same. 4. To know the maximal recording time for HDDs with different capacity, please refer to the table of HDD recording time (on the pages 66 and 67)

25 CHAP.4 DVR Operation (2) SCHEDULE SETUP Unless you select another recording mode, DVR system will record in continuous recording mode. In SCHEDULE SETUP, you can set recording type of one-hour intervals. The frame rate default for continuous recording speed is 30 FPS. Click ALL to set the entire grid as the designated recording mode in TYPE. HOUR DATE Channel: Select a channel to adjust setting. TYPE: Designates a recording mode to alter the setting value of the DATE/TIME grid. -CONTINUE: Records continuously. -ALARM: Records once receiving alarm signals. -MOTION: Records once detecting motion. -MOTION & ALARM: Records once receiving alarm signals or detecting motion. ALL: Set the entire grid (24 hours a day/7 days a week) as the designated recording mode in TYPE. DATE: Click a day on the menu to set 24 hours of that day as the designated recording mode. HOUR: Click an hour on the menu to make the DVR record in the designated recording mode during this hour everyday. NOTE : 1. Each type is marked in a different color. You can vary the recording schedule by pressing the left button and dragging the cursor on the grid.2. To demand the DVR not to record during some time, click the right button on blocks of the grid

26 CHAP.4 DVR Operation CONFIGURATION HDD MANAGEMENT HDD MANAGEMENT CAMERA SETUP MOTION SETUP ALARM SETUP INTERVAL SETUP TIME/DATE SETUP MODEL SERIAL BLOCKS SIZE SPEED MAXTOR 6Y080L0 S LBA 160 GB PIO4 PASSWORD SETUP BUZZER SETUP OVERWRITE DISABLE ESC FORMAT ESC 3. CONFIGURATION Click CONFIGURATION, and you can open the menu shown below, containing eight configuration items: (1) HDD MANAGEMENT Items above the line clearly present the Information of the HDD, covering the model name, the serial number, the number of blocks, etc. Other items are for you to operate the HDD. MODEL: Indicates the model name of the HDD. SERIAL: Indicates the serial number of the HDD. BLOCKS: Indicates the HDD LBA BLOCK Number. SIZE: Indicates total size of the HDD. SPEED: Indicates the PIO mode of the HDD, which determines the transferring rate between the DVR and the HDD. OVERWRITE: Enable or disable overwriting the HDD when it is stuffed with recorded images. If it is enabled, the original recorded data will be replaced by new images. Oppositely, the DVR will cease recording if the function is switched off. FORMAT: Click it to remove all the recorded images by formatting the HDD. NOTE : 1. While HDD MANAGEMENT opens, the DVR will not record. 2. If combining a new HDD with the DVR, you need to format it first to enable the HDD to record images

27 CHAP.4 DVR Operation (2) CAMERA SETUP On this menu you can adjust the camera setting. CHANNEL: Select a channel to adjust setting. TITLE: Name a camera with a combination of up to 8 digits or letters. BRIGHTNESS: Adjust the brightness of camera images. CONTRAST: Adjust the contrast of camera images. SATURATION: Adjust the saturation of camera images. HUE: Adjust the hue of camera images. (3) MOTION SETUP CAMERA SETUP CHANNEL CH1 TITLE CAM01 BRIGHTNESS 0 CONTRAST 0 SATURATION 0 HUE 0 DEFAULT ALL-DEFAULT ESC MOTION SETUP CHANNEL CH1 SENSITIYITY 5 DURATION 05 DETECT CELL NUMBER 01 DEFAULT ALL-DEFAULT ESC CHANNEL: Select a channel to adjust setting. SENSITIYITY: Adjust the sensitivity of motion detection. DURATION: Set the recording time after a camera detects any motion. DETECT CELL NUMBER: Determine the minimal cells (blocks in the grid) that activate a motion event. MOTION DETECTION GRID: Determine the coverage of motion detection. On this grid, press the left button and drag the cursor to disable cells to detect motion. To enable them, use the right button. NOTE : A camera must be scheduled as motion detecting mode to make it work in compliance with the setting in this MOTION SETUP. ( Refer to the page 25 to set SCHEDULE SETUP.) 27 27

28 CHAP.4 DVR Operation (4) ALARM SETUP Users can rectify the alarm sensor setting here. CHANNEL: Select a channel to adjust setting. INPUT: Select the type of the alarm sensor connected to the DVR. -NORMAL OPEN: For an alarm type triggered once a normally open device, such as an open door, is closed. -NORMAL CLOSE: For an alarm type triggered once a normally closed device, such as a close window, is opened. -DISABLE: Disable the alarm function. DURATION: Set the alarming time after an alarm sensor is triggered. CHANNEL INPUT DURATION DEFAULT ALRAM SETUP CH1 NORMAL OPEN 05 SEC ALL-EFAULT ESC (5) INTERVAL SETUP The switching interval of channel sequence in the main screen or in the PIP small window can be switched in this menu. SEQUENCE SCREEN: Set the switching interval of channel sequence in the live full screen. PIP SCREEN: Set the switching interval of channel sequence in the PIP window. EVENT UPDATE: Set the event update duration in the list of EVENT SEARCH. INTERVAL SETUP SEQUENCE SCREEN PIP SCREEN EVENT UPDATE DEFAULT 01 SEC 01 SEC 600 SEC ESC NOTE : On condition that a user sets the event update duration as 100 seconds, when the DVR detects an event (such as ALARM, or MOTION) and creates an event entry, events that occur during the following 99 seconds will be recorded in the same entry. That is, if there is any event occurring from or later than the 100 th second, the DVR will record it into another entry

29 CHAP.4 DVR Operation (6) TIME/DATE SETUP On this menu, you can set the time/date and their formats the DVR displays. DATE TIME/DATE SETUP 2007/JUL/01 DATE: Regulate the date of the DVR. TIME: Regulate the time of the DVR. DATE FORMAT: Switch the date format. HOUR FORMAT: Switch the hour format. MONTH FOMAT: Switch the month format. TIME 12:00 :00 DATE FORMAT ASIAN HOUR FORMAT 24HOUR MONTH FORMAT NUMERIC DEFAULT ESC (7) PASSWORD SETUP Users can rectify the password here for: (i). Logging into MAIN MENU. (ii) Formatting the HDD (iii) Upgrading the firmware USER ID USER PW NEW PW PASSWORD SETUP ADMIN USER ID: This is fixed as ADMIN (administrator) and unchangeable. USER PW: Input the present password to inform the DVR you possess the authority to change it. NEW PW: Create a new password by inputting up to 8 digits. CONFIRM: Repeat the newly created password for confirmation. CONFIRM ENTER ESC Number Bar for Password Input NOTE : 1. Click on an item on the left side (USER PW/ NEW PW/CONFIRM) first to activate the corresponding input space. Then, input a password via the number bar, and click ENTER to affirm it. 2. The password default is none. For security reasons, changing the password is highly recommended. (8) BUZZER SETUP KEY TONE: Switch on/off all clicking sounds. VIDEO LOSS: Switch on/off the cautionary buzz, which will be activated once the DVR losses any video signal. ALARM ACTIVE: Switch on/off the alarm function. BUZZER SETUP KEY TONE ON VIDEO LOSS ON ALARM ACTIVE ON MOTION DETECT ON DEFAULT ESC MOTION DETECT: Switch on/off the cautionary buzz, which will be activated once the DVR detects any motion

30 CHAP.4 DVR Operation 4. EXTERNAL DEVICE In this menu, you can set parameters of external devices, a computer via the network, a PTZ camera, and a SPOT monitor, connected to the DVR. EXTERNAL DEVICE TCP/IP SETUP PAN/TILT SETUP SPOT SETUP (1) TCP/IP SETUP The function enables you to see live and recorded images via the network. (A) IP SETUP: MAC ADDRESS: Indicates the unique code assigned to the DVR. DHCP MODE: Decide to set parameters, say an IP address, manually or to automatically receive them in the DHCP mode. IP DETECT: When setting DHCP MODE as AUTOMATIC, users can click this item to detect an IP address and relevant data. IP PORT: Set the IP port of the DVR. IP ADDRESS: Set the IP address of the DVR. GATEWAY: Set the gateway IP address of the DVR. SUBNET: Set the subnet mask of the DVR. IP SETUP DDNS SETUP SPEED MAC ADDRESS DHCP MODE IP PORT IP ADDRESS GATEWAY SUBNET TCP/IP SETUP ESC ESC IP SETUP 00-0A-A2-04-5E-65 MANUAL IP DETECT DEFAULT ESC (B) DDNS SETUP DDNS ENABLE: Enable or disable the DDNS function. DNS SERVER: Set the IP address of the DNS server. INTERVAL: Set the connection time between the DVR and the DDNS server. ( D = Days, H= Hours, M = Minutes) DDNS STATUS: Indicates whether the DVR is registered to the DDNS server. IP ADDRESS: Indicates the IP address of the DVR. IP PORT: Indicates the IP port of the DVR. REMAIN TIME: Indicates the remaining time for connection. LAST REGISTRATION DATE: Indicates the nearest registration date. DDNS ENABLE DNS SERVER INTERVAL DDNS SETUP DDNS STATUS IP ADDRESS IP PORT REMAIN TIME LAST REGISTRATION DATE DEFAULT SPEED OFF D-00 H-00 M-20 REGISTER ESC (C) SPEED: Select a speed parameter for data transmission via the network. SPEED 5 DEFAULT ESC 30 30

31 CHAP.4 DVR Operation (2). PAN/TILT SETUP (A) COMMAND SETUP CHANNEL: Select a channel to adjust setting. MODEL: Select a camera model (protocol type) that corresponds with your PTZ camera. PTZ ID: Adjust the camera ID. BAUDRATE: Select a data transmission rate. CMD DELAY: While the DVR and the PTZ camera operate in different speed, users will need to set a applicable buffer time for processing commands. COMMAND: Select a PTZ camera command, and its length and code will be indicted in LENGTH and CODE. LENGTH: Indicates the length of the selected PTZ command. CODE: Indicates the code of the selected PTZ command. COMMAND SETUP SPEED SETUP CHANNEL MODEL PTZ ID BAUDRATE CMD DELAY COMMAND LENGTH CODE DEFAULT PAN/TILT SETUP DEFAULT COMMAND SETUP ALL-DEFAULT ESC CH1 PELCO-D BPS 1.00 MSEC PAN LEFT 07 FF F ESC (B) SPEED SETUP PAN SPEED: Set the panning speed for a PTZ camera. TILT SPEED: Set the tilting speed for a PTZ camera. ZOOM SPEED: Set the zooming speed for a PTZ camera. SPEED SETUP PAN SPEED 7 TILT SPEED 7 ZOOM SPEED 7 DEFAULT ESC (3) SPOT SETUP SWITCHING INTERVAL: Set the switching interval of the SPOT monitor. ALARM POPUP: With this function on, once receiving alarm signals from any channel, the DVR will enable the SPOT monitor to cease channel sequence and display the live images of this channel. MOTION POPUP: With this function on, once detecting motion from any channel, the DVR will enable the SPOT monitor to cease channel sequence and display the live images of this channel. EVENT POPUP DURATION: Set the duration of pop-up displaying for the SPOT monitor. NOTE : SPOT SETUP SWITCH INTERVAL 03 SEC ALARM POPUP ON MOTION POPUP ON EVENT POPUP DURATION 05 SEC DEFAULT ESC 1. During the duration of a pop-up event (ALARM or MOTION), if another event happens, the SPOT monitor will switch to display the latest one. 2. If two or more events are triggered simultaneously, the SPOT monitor will display them sequentially

32 CHAP.4 DVR Operation 5. BACK-UP USB SETUP Users can backup the recorded images into an USB mass-storage device via the HOST slot on the rear of the DVR. Set the starting time and the backup size first, and the DVR will automatically detect the ending time. Afterwards, click BACKUP, and the data will be recorded into the storage device. BACK-UP HDD START: Depicts the starting time point of all the HDD recorded images END: Depicts the ending time point of all the HDD recorded images. MEDIA PARTITION: Indicates the free space of total memory in the USP device. START: Select a starting time point for the backup images. END: Depicts the detected ending time point for the backup images according to MEDIA START and MEDIA SIZE. SIZE: Select a size for backup images. BACK-UP: Click it to launch backup process. USB SETUP USB SETUP ESC HDD START 2007/ 07/15 12:38:23 END 2007/ 07/16 18:39:09 MEDIA PARTITION 416MB/ 983MB P:1 START 2007/07/15 12:38:23 END 2007/07/15 13:55:27 SIZE MB 416 MB USB STORAGE IS AVAILABLE BACK UP ESC 6. FIRMWARE UPGRADE CURRENT VER: Depicts the current firmware version of the DVR. UPGRADE VER: Depicts the upgrade firmware version the DVR detects in the USB mass-storage device. (Users have to execute CHECK USB first.) CHECK USB: Click it to detect the upgrade version of the firmware in the USB mass-storage device. UPGRADE: Click it to upgrade the DVR. CURRENT V ER 1.30_SP FIRMWARE UPGRADE UPGRADE VER CHECK USB UPGRADE ESC Step 1 Step 2 7. LANGUAGE There are 14 languages available in the DVR system. Click on the underlined item shown at right to select the language you need

33 CHAP.5 Network Setup CHAP.5 Network Setup 5-1 DVR Network Configuration Please inquire your network provider first to identify what type of Internet service it provides. You need to know what follows: (1) Upload speed: expected frame rates. (2) Download speed: expected frame rates. (3) Addressing: to make sure which scenario you should follow. (4) Router or modem: to make sure which scenario you should follow. NOTE : 1.If your provider uses PPPoE (usually a DSL provider does), you MUST have a router installed and follow instructions in 5-4 Dynamic IP of PPPoE (DSL) (on the page 36) for DVR setup and access. 2.Please verify the Internet access after installing any new equipment (a router, a switch, a modem, etc.). TCP/IP Setting of your PC Before configuring the DVR, please fill out the information listed below if available. Choose any PC on your network and determine its TCP/IP setting. IP Address: (ex ) Subnet Mask: (ex ) Default Gateway: (ex ) Next pages are several network scenarios. Please identify within which scenario your current network falls and follow the instructions for configuring and accessing your DVR via the TCP/IP

34 5-2 Static IP CHAP.5 Network Setup The TCP/IP function enables you to: (1) See live images and recorded images (2) Control a PTZ camera via Internet (3) Backup. In IP SETUP (MENU EXTERNAL DEVICE TCP/IP SETUP IP SETUP) for the DVR, please input an IP address assigned from the ISP. Operation Steps (1) Verify the IP address is correct for your PC before connecting it with the DVR. (2) Connect an LAN cable to the DVR after confirmation. (3) Go to IP SETUP of the DVR, and set DHCP MODE as MANUAL. (4) Verify if MAC ADDRESS starts from 00-0A-A2. (5) Set IP ADDRESS (assigned from the ISP). (6) Set IP PORT (50000 is recommended). (7) Set GATEWAY (assigned from the ISP). (8) Set SUBNET (assigned from the ISP). (9) Go out of MAIN MENU. (10) Turn off and on the modem (router) the ISP provides to reset clients of MAC from the ISP. Users need to wait for 30 seconds after turning on. (11) Access the DVR via the Remote Viewer, which you can install via the software CD. NOTE : If you fail to access, please verify step (1),(5),(6),(7),(8), or (10) again

35 5-3 Dynamic IP CHAP.5 Network Setup If you set DHCP MODE as AUTOMATIC in IP SETUIP (MENU EXTERNAL DEVICE TCP/IP SETUP IP SETUP), IP information will be automatically assigned from the ISP of DHCP. Operation Steps (1) Verify the IP address is correct for your PC before connecting the DVR. (2) Connect an LAN cable to the DVR after confirmation. (3) Turn off and on the modem (router) the ISP provides to reset clients of MAC from the ISP. Users need to wait for 30 seconds after turning on. (4) Verify MAC ADDRESS starts from 00-0A-A2. (5) Set DHCP MODE as AUTOMATIC. Then click IP DETECT to get a dynamic IP. (6) Go out of MAIN MENU after getting the IP successfully. (7) Access the DVR via the Remote Viewer, which you can install via the attached software CD. NOTE : If you fail to access, please verify step (1), (3), or (4) again

36 CHAP.5 Network Setup 5-4 Dynamic IP of PPPoE (DSL) The DVR doesn t support DSL (PPPoE), so users have to set the network with a router (for IP sharing) if they need to access it remotely. In this case, they have to port forward on the DVR. NOTE : Please contact the router s manufacturer if you need to know how to do. If users have a static or dynamic IP but still tend to use another device, say a PC, through a router, they can set the network following the steps: Operation Steps (1) Verify the IP address is correct for your PC before connecting the DVR. (2) Connect the router to a DSL modem as the flow chart shown below. (3) Set the Internet connection of the router. ( Refer to the router manual.) (4) Verify the router s network sub-group is correct. (5) Connect the DVR to the router. (6) Set DHCP MODE as MANUAL in IP SETUP(MENU EXTERNAL DEVICE TCP/IP SETUP IP SETUP),. (7) Verify MAC ADDRESS starts from 00-0A-A2. (8) Input an internal IP address (assigned from the router). (9) Set IP PORT (50000 is recommended). (10) Set GATEWAY (of the router). (11) Set SUBNET (of the router). (12) Go out of MAIN MENU. (13) Forward a port from the router. ( Refer to the router manual.) (14) Access DVR with external IP address and port. ( Refer to the router manual.) NOTE : 1. If the router supports DDNS, you can use domain information to access the Remote Viewer. 2. If you fail to access, please verify step (1), (4), or (15) again

37 CHAP.6 DVR Program Setup CHAP.6 DVR Program Setup 6-1. Registering DVR for DDNS (DDNS Web-server) (1) To connect the DVR via the Internet, registration to the DDNS web-server is necessary. Please access first. In this homepage, click Member Register to create a member ID. After filling up the form and confirmation, a message of Success! will show, and you will be automatically returned to the previous page. (2) Please click Login in the upper right corner to enter My DVR List and then DVR Add to register the DVR

38 CHAP.6 DVR Program Setup (3) Please click Confirm after filling out this form shown as below. (4) Now, some information of the DVR is listed on the DDNS web server, short of the IP address and the port number

39 CHAP.6 DVR Program Setup 6-2. DDNS Setup in DVR Configuration for a cable modem connected to DVR directly is illustrated as below. (1)Open IP SETUP (MENU EXTERNAL DEVICE TCP/IP SETUP IP SETUP) and set DHCP MODE as AUTOMATIC, letting the DVR detect an IP address automatically. (2) Shift to DDNS SETUP (MENU EXTERNAL DEVICE TCP/IP SETUP DDNS SETUP). Set DDNS ENABLE as ON and an IP address will be automatically assigned to DNS SERVER from the DHCP server. After that, click REGISTER to renew the IP registered in DDNS SERVER. MAC ADDRESS DHCP MODE IP SETUP 00-0A-A AUTOMATIC IP DETECT IP PORT IP ADDRESS GATEWAY SUBNET DEFAULT ESC DDNS SETUP DDNS ENABLE ON DNS SERVER INTERVAL D-00 H-00 N-20 REGISTER DDNS STATUS REGISTER OK IP ADDRESS IP PORT REMAIN TIME D-00 H-00 N-20 LAST REGISTRATION DATE > WED. 12 JUL : 21 : 36 GMT DEFAULT ESC 39 39

40 CHAP.6 DVR Program Setup (3) Return to your computer after you see a message of SUCCESS TO REGISTER DVR INFO. Then, click (Refresh) to let the DDNS server automatically fetch your DVR s IP address and port number. NOTE :Prior to using the Web Viewer, please add into Trusted Sites first as illustrated below (Tools Internet Options Security Trusted Sites Sites): Refresh it. IP: Port automatically fetched 40 40

41 41 41 CHAP.6 DVR Program Setup

42 CHAP.6 DVR Program Setup 6-3. DVR Web Viewer (via IE) DVR WEB VIEWER is a program for users to remotely monitor via the IE. (1) Please click to execute DVR WEB VIEWER as following illustration: NOTE : 1. If ActiveX control installation is required in the first access, please click Yes.. 2. Users can also execute this program by clicking the file named RemoteWeb.html in the software CD. (2) Later, DVR WEB VIEWER will pop up. Please click CONNECT to see live images

43 CHAP.6 DVR Program Setup (3) The live images are displayed as below: 43 43

44 CHAP.6 DVR Program Setup 6-4. DVR Backup Player (via IE) DVR BAKCUP PLAYER is a program for users to replay backup image files through the IE. (1) To execute DVR BACKUP PLAYER, click shown as below: NOTE :. 1. If ActiveX control installation is required in the first access, please click Yes. 2. Users can also execute this program by clicking the file named WebPlayer.html in the software CD. (2) Following that, BACKUP PLAYER will pop up. Please click OPEN to select files. (3) Select a backup image file and then click Open to replay recorded images

45 CHAP.6 DVR Program Setup (4) You can see the recorded images shown as below

46 CHAP.6 DVR Program Setup 6-5. Web Network Backup (via IE) This is a program for users to backup recorded images via the IE. (1) Go to and click DVR Web Backup on the left. NOTE : Users can also execute this program by clicking the file named WEB_BACKUP.html in the software CD. (2) To execute backup via the network, input the IP address as well as the network port and then click Connect Test

47 CHAP.6 DVR Program Setup (3) When the connection test is done, a message of Success Connect Test will show. Then, click Lock to set backup time. (4) Now, please set well Recorded Start Time, Recorded End Time, Save File Path, and Maximum Save File Size. Right after that, click Apply

48 CHAP.6 DVR Program Setup (5) Next, click Start Backup to start recording images. Finally, you can review the backup files via the path you have already determined

49 CHAP.6 DVR Program Setup 6-6. DVR Remote Viewer DVR Remote Viewer is a program for distant users to monitor, replay, and backup recorded images via the network. NOTE : Prior to making use of this program, users have to install it from the software CD. 1. Main Interface 1- POWER: Click POWER to exit the program. Please disconnect the connection before turning off the software. 2- CONNECT: Click CONNECT to view the live images from the DVR, identical to those being displayed on the DVR, with a delay depending on your Internet connection between the DVR and where you are accessing. 3- DISCONNECT: Click this button to disconnect from the DVR, and then you can power off the software. 4- SCREEN DIVISION: Select the full-screen mode or the 4-split-screen mode. In the full-screen mode, you will see the number button of the channel you currently see is highlighted. 5- CHANNEL: Select a channel, if connected, that you want to see in the full-screen mode. 6- STATUS WINDOW: Displays the current time and date of the program. You will also see the current connection status. 7- SEQUENCE/SETTING/PLAYBACK: (1) Sequence: In the full-screen mode, click this button and all active channels will be displayed in sequence at a speed specified in the settings menu. (2) Setting: Enables the configuration screen. (3) Playback: Enables the remote playback screen. 8- PTZ control: You can control a PTZ camera via the program by following these suggestions: (a) First, you must configure a specific PTZ protocol in the program to communicate with the PTZ device. (b) When using any control button for the PTZ, please press and hold it for 1~ 2 seconds to compensate for the data transmission rate. If you simply click the control button, you may get undesired results (e.g. having the requested operation transmitted repeatedly, regardless of your intention). (c) The plus and minus buttons send PTZ commands to a corresponding PTZ camera ID

50 CHAP.6 DVR Program Setup 2. IP/PORT Setting MANUAL: Input an IP address and a port manually. DDNS: Receive an IP address and a port from the DDNS Server. For further information of DDNS, please contact your vendor. NAME: The name of the IP address on the list. ADDRESS: Input an IP address set in the DVR. PORT: Input the port set in the DVR USER ID: Input the ID set in the DVR. (Please input admin, a fixed parameter.) PASSWORD: Input the password set in the DVR IP List: Shows all IP addresses users have inputted manually. Select: Select an IP address on the list. Save: Save an IP address set on the list. Delete: Delete an IP address on the list. IP List 50 50

51 CHAP.6 DVR Program Setup 3. DDNS Setting Member ID: Input the member ID registered at the DDNS server. Name: Input the DVR name registered at the DDNS server. Save: Save the member ID and the name. Load: Search for a member ID & name saved in the Remote Viewer. User ID: Input the ID set in the DVR. (Please input admin, a fixed parameter.) Password: Input the password for the DVR. Connect: Receive the IP address and the port for the DVR from the DDNS server

52 CHAP.6 DVR Program Setup 4. PTZ/SAVE Setting Circular Monitoring Interval: Select the switching interval of channel sequence when users active the sequence function on the main interface. Scan Rate: Set the speed of playback. PTZ Type: Select the PTZ camera type connected to the DVR. PTZ Baudrate: Enter the baud rate of your PTZ camera. Set Path to Save Downloaded image: Determine the storage folder in your PC where the downloaded video clips will be stored. Run in Full Screen Mode: If selected, it will enable the program to readjust the interface to fill your computer screen fully

53 CHAP.6 DVR Program Setup 5. Playback Interface through The DVR Remote Viewer Functions of all buttons in Search window are delineated below: 1 Exit: Exit to the live window. 2 Full-screen mode: Select a certain camera to view in the full-screen mode. 3 4-split mode: View images in the 4-split mode. 4 Time: Indicates the recording time of the image being replayed. 5 Channel selection: Select a camera to be replayed. 6 Time selection: Select a time point from which the playback will be started (Use the mouse to drag the point) 7 Start and end time: Indicates the start and end time of the recorded images on the HDD 8 Other operating button: ( please refer to the next page.) 53 53

54 CHAP.6 DVR Program Setup Play Backward Fast Move to the Start of Recording Play Backward Move to the Previous Hour Play Forward Move to the Next Hour Play Forward Fast Move to the End of Recording Stop Playback 9 Command: (a) SAVE: After clicking Stop Playback, click SAVE to save the image viewed currently in the JPEG format. (b) PRINT: After clicking the Stop Playback, click PRINT to print the image viewed currently. (c) EVENT: Open the event list to select and replay an recorded event images. (d) RECORD: Click this button to download playback images transmitted from the DVR to a PC. Press it (button light: blue red)and the program will start to record images. Then, press again to save the images during the recording period into an AVI file, which can be played by Windows Media Player. 10 Calendar: Select the date of the recorded images you need. The outlined square indicates the ending data of recorded images in the HDD. The square in gray represents the date of current playback that you can change by clicking. NOTE : If an invalid date is selected, it will default to the beginning of all recorded images

55 CHAP.6 DVR Program Setup 6-7. Backup CD Player Using Backup CD Player, users can replay backup image files, and function of each button in Backup CD player is as below. NOTE : Before making use of this program, users have to install it from the software CD. 1 Time: Show the current time. 2 Status Window: Show the start and end time/date, and status of operating button. When users replay forward/backward, the recording time will be displayed. 3 Play Speed button: User can adjust replay speed by clicking up/down button. (1)SPEED: Adjust the speed (1/4X, 1/2X, 1X, 2X, 4X, 8X, or 16X) for 4 (b) or (e) buttons. (2)DELAY: Slow down replaying (1, 2, 4, 8, 16, or 32). 4 Operation: Users can search recorded data via these buttons. (a) Move the slide bar to the start position (b) Play backward fast in a preset speed (c) Play backward at a normal speed (d) Pause (e) Play forward fast in a preset speed (f) Move the slide bar to the end position (g) Play forward at a normal speed. 5 FUNCTION: (1) OPEN: Open the Backup CD Player. (2) EDIT: Users can edit, save and print recorded image in the edition mode. This button will work when you select one of the16 cameras. (3) EXIT: Exit from the Backup CD Player. 6 CHANNEL: Select channel to see images in a full screen. 7 SLIDE BAR: Move to a time point from which users want to the program to replay. 8 PAGE: This button will work for a 8 CH DVR in a 4-split screen, or for a16 CH DVR in a 4-split or 8-split screen. Click it to move to the next page. 9 SCREEN DIVISION: Select the screen mode in a full screen, a 4-split, 9-split, or a 16-split screen

56 CHAP.6 DVR Program Setup Image EDIT..(a). (b) (c) 1 Image Edit Status Window: Shows the recording time/date, the image size, and the command status. 2 Edit Button: Users can adjust color tone of copied images using these buttons. (a) Contrast Plus: Enhance light and shade of an image. (b) Brightness Plus: Make an image brighter. (c) Sharpness: Make an image more sharp-edged. (d) Contrast Minus: Reduce light and shade of an image. (e) Brightness Minus: Make an image darker. (f ) Blur: Soften an image. 3 Function button: (a) Save: Users can save images, in the JPEG format, in the folder where you installed the Backup CD Player. (b) Print: User can print current image user selected. (c) Exit: Return to the Backup CD Player mode

57 CHAP.7 Media Player CHAP.7 Media Player ( This chapter is for LR-804J02 only) 7-1. Remote Controller Preparing The Remote Controller for First Use 1. Activate the Remote Controller The remote control ships with a plastic contact breaker between the battery and contact. You must remove the contact breaker prior to use by pulling out the tab. NOTE : Preserve the contact breaker in case you need to return the DVR to the vendor. 2. Operative Range of the Remote Controller The remote controller operates the Media Player via infrared transmission. To make the remote controller function well, please direct it toward the receiver (infrared port) on the front panel of the DVR. Without barriers between the controller and the receiver, effective distance is 5~10 meter (dependent on its power status) and effective degrees 30 up, down, left, and right from the infrared port. 3. Notice 1. If the remote control does not work well, get closer to the receiver or check if the battery needs replacement. 2. Only a 3V CR2025 battery is compatible with the remote controller. 3. Dispose of used batteries complying with local regulations. 4. If you do not use the remote controller for an extended period, please remove the battery