RLS-1000B Remote Link Switch
|
|
- Ronald Cobb
- 6 years ago
- Views:
Transcription
1 RLS-000B Remote Link Switch Instruction Manual Computer Automation Technology Inc. 8 W. Atlantic Blvd. #9 Margate, Florida 06 Phone: Internet:
2 The RLS-000B provides a method to connect up to three transceivers to the remote base port of the controller or two transceivers to the CAT-00 controller. Transceiver selection is accomplished by grounding three control lines. Since the receiver audio and inputs are mixed, all three transceivers can be selected at the same time. To select a transceiver, connect the controller s user function switch outputs to the control line inputs on the RLS-000B. # # # PORT # PORT # PORT # RLS-000B REMOTE LINK SWITCH CAT CONTROLLER PORT R Output Polarity The Repeater output (J-) will always be active HIGH. The polarity dipswitch on the controller must be set to the OFF position. Audio Input Output The audio input and output circuits are identical to the CAT Controllers. Level adjustments on both the input and output amplifiers make it easy to compensate for varying input and output requirements. The audio input impedance is 0K ohms while the output impedance is 600 ohms. Receiver Audio Response Each receiver input has a buffer amplifier with a gain of three. The frequency response is flat over a range of 00 to 000 Hz. If discriminator audio is being used, it may be necessary to add some high frequency roll off. Space has been provided to install a capacitor across the feedback resistor on each receive audio amplifier. These locations are identified on the RLS-000B board as C, C and C6. Start with a.00uf capacitor. Increase the value to provide more high frequency roll off or decrease the value to provide less high frequency roll off. PAGE
3 Dip Switch Selection Switch # - Port # Polarity This switch determines input logic for the RLS-000B port # input. Switch # should be OFF if the input is active high and ON if the input is active low. For an active low input a pull-up resistor may be required. Install a jumper on P- to add a 00 ohm.w resistor on the RLS-000B board at the R position. Switch # - Port # Polarity This switch determines input logic for the RLS-000B port # input. Switch # should be OFF if the input is active high and ON if the input is active low. For an active low input a pull-up resistor may be required. Install a jumper on P- to add a 00 ohm.w resistor on the RLS-000B board at the R position. Switch # - Port # Polarity This switch determines input logic for the RLS-000B port # input. Switch # should be OFF if the input is active high and ON if the input is active low. For an active low input a pull-up resistor may be required. Install a jumper on P- to add a 00 ohm.w resistor on the RLS-000B board at the R position. Switch # - Port # Configuration This switch configures port #. If a transceiver is connected to the RLS-000B at port #, dipswitch # should be in the OFF position. If a repeater is connected to port #, dipswitch # should be in the ON position. Switch # - Port # Configuration This switch configures port #. If a transceiver is connected to the RLS-000B at port #, dipswitch # should be in the OFF position. If a repeater is connected to port #, dipswitch # should be in the ON position. Switch #6 - Port # Configuration This switch configures port #. If a transceiver is connected to the RLS-000B at port #, dipswitch #6 should be in the OFF position. If a repeater is connected to port #, dipswitch #6 should be in the ON position. Switch # - Port # Priority Enable Switch # provides a method of assigning port # with priority over ports # and #. If switch # is OFF the RLS-000B will be configured for normal operation. Any input will enable the corresponding audio switch and pass the receive audio to the mixer. If switch # is ON port # will have priority. Audio switches for ports # and # will be disabled when port # is active. Switch #8 - Port # CAT-00 Mode Enable This switch configures the RLS-000B for operation with the CAT-00 controller in the one repeater, twotransceiver mode. PAGE
4 CAT RLS-000B Interconnect Three Repeater two Links Figure describes how to connect three repeaters to the repeater port of the CAT-800 controller while providing support for two link transceivers. Use the CAT-800 user function switches one, two and three to control the RBS-000B Remote Base Switch. The repeaters must remain linked with their logics active high. J-8 J- J- J- J- J- # # # # # # CAT-800 J-8 J- J- J- J- J- # # # # # # J-6 J- J-0 J- J- J-6 J- # # # # # +VDC OUTPUT J- J- J-9 USER OUTPUT # USER OUTPUT # USER OUTPUT # J- J- J-6 J- J- J- J- J-8 J- J- PORT # CONTROL PORT # CONTROL PORT # CONTROL +VDC INPUT REPEATER OUT REPEATER PORT # RLS-000B 8 PORT # 8 REPEATER # REPEATER # PORT # 8 REPEATER # Figure PAGE
5 CAT-00B / CAT-0B RLS-000B Interconnect Figure describes how to connect three remote base transceivers to the link port of the controller. Use the controller s user function switches one, two and three to control the RBS-000B Remote Base Switch. J- J- J- J-0 J- J-6 # # # # # REPEATER CAT-00B CAT-0B J- J- J- J- J- J- J-9 J- J- J-6 J- J- J- J-9 J-0 USER INPUT # USER INPUT # USER INPUT # USER INPUT # # # # # # +VDC OUTPUT USER OUTPUT # USER OUTPUT # USER OUTPUT # USER OUTPUT # J-8 FAN CONTROL J- J- J-6 J- J- J- J- J-8 J- J- PORT # CONTROL PORT # CONTROL PORT # CONTROL +VDC INPUT REPEATER OUT REPEATER PORT # RLS-000B PORT # PORT # Figure PAGE
6 CAT-800 RLS-000B Interconnect Figure describes how to connect three remote base transceivers to port # of the CAT-800 controller. Use the CAT-800 user function switches one, two and three to control the RBS-000B Remote Base Switch. J- J- J- J-0 J- J-6 # # # # # REPEATER PORT # CAT-800 J-8 J- J- J- J- J- # # # # # # PORT # J- J- J-9 J- J- J-6 J-8 J- J- J-9 # # # # # +VDC OUTPUT USER OUTPUT # USER OUTPUT # USER OUTPUT # J- J- J-6 J- J- J- J- J-8 J- J- PORT # CONTROL PORT # CONTROL PORT # CONTROL +VDC INPUT REPEATER OUT REPEATER PORT # RLS-000B PORT # PORT # PAGE Figure
7 CAT-00/CAT-00DX - RLS-000B Interconnect The RLS-000B provides a method to connect a repeater and two transceivers to the CAT-00 repeater controller. On the RLS-000B set dipswitch #8 to ON. Transceiver selection is accomplished by grounding two of the control lines. To select a transceiver, enable the CAT-00 user function switch outputs connected to the control line inputs of the RLS-000B. On the CAT-00, enable Zone 6 channel to convert output # to a transceiver and input # to a transceiver. CAT-00 CAT-00DX J- J- J-0 J-6 J- J-9 J- J- J-6 J- J- J-8 # # INPUT # USER OUTPUT # # # +VDC OUTPUT USER OUTPUT # USER OUTPUT # J- PORT # CONTROL J- PORT # CONTROL J- J- J- J- J-8 J- +VDC INPUT REPEATER REPEATER RLS-000B PORT # REPEATER PORT # PORT # PAGE 6 Figure
8 CAT-00 RLS-000B Interconnect Figure 6 describes how to connect three remote base transceivers to the link port of the CAT-00B controller. Use the CAT-00B user function switches one, two and three to control the RBS-000B Remote Base Switch. J- J- J- J-0 J- J-6 # # # # # REPEATER CAT-00B J- J- J- J- J- J- J-9 J- J- J-6 J- J- J- J-9 J-0 USER INPUT # USER INPUT # USER INPUT # USER INPUT # # # # # # +VDC OUTPUT USER OUTPUT # USER OUTPUT # USER OUTPUT # USER OUTPUT # J- RBI- DATA J-8 RBI- CLOCK J- RBI- RESET J- J- J-6 J- J- J- J- J-8 J- J- PORT # CONTROL PORT # CONTROL PORT # CONTROL +VDC INPUT REPEATER OUT REPEATER PORT # RLS-000B PORT # PORT # Figure 6 PAGE
9 Parts List 8 Capacitor 0uF 6V C,C,C,C6,C9,C,C,C8 Capacitor 0.uF 0V C,C,C8,C0,C,C,C Capacitor.00uF 0V C,C,C6 (Select Part) Connector DB-9F J,J,J Connector DB-F J Crystal MHz Y Diode N8 CR,CR,CR Header X J I.C. LM0T- U I.C. ICL660 U I.C. AT89CJC U6 I.C. TD608AP U0 I.C. TPIC6C9 U9 I.C. DS U I.C. LM8 U,U I.C. MAXCNG U,U8 Jumper JP Resistor 0K Variable R,R,R Resistor K Variable R,R,R9 Resistor 0K 0Pin SIP R Resistor 0K 6Pin SIP R8,R9,R0,R Resistor.K 0Pin SIP R Resistor 680 6Pin SIP R Resistor 00.W R,R Resistor 60.W R6,R6,R8,R0 Resistor 00.W R,R,R (Select Part) 0 Resistor 0K.W R,R0,R,R,R8,R9,R,R,R6,R6 Resistor K.W R,R,R Switch Dip 8 Position SW PAGE 8
10 Drawing PAGE 9 Figure
11
12
ES-562/564U COMBINATION CLOCK/TIMER
142 SIERRA ST., EL SEGUNDO, CA 90245 USA (310)322-2136 FAX (310)322-8127 www.ese-web.com ES-562/564U COMBINATION CLOCK/TIMER OPERATION AND MAINTENANCE MANUAL The ES-562U/564U is a combination six digit
More informationSierra Radio Systems. Digital Compass. Reference Manual. Version 1.0
Sierra Radio Systems Digital Compass Reference Manual Version 1.0 Contents Digital compass board RS485 power injector For more information, go to the Sierra Radio Systems web site at www.sierraradio.net
More informationDEV-1 HamStack Development Board
Sierra Radio Systems DEV-1 HamStack Development Board Reference Manual Version 1.0 Contents Introduction Hardware Compiler overview Program structure Code examples Sample projects For more information,
More informationSierra Radio Systems. HamStack. Project Board Reference Manual V1.0
Sierra Radio Systems HamStack Project Board Reference Manual V1.0 Welcome HamStack Project Board Reference Manual Revision 1.0.3 2011 George Zafiropoulos, KJ6VU and John Best, KJ6K This guide provides
More informationDS34RT5110-EVKC HDMI / RJ45 Extender Demo Kit for CAT5 Cables
DS34RT5110-EVKC HDMI / RJ45 Extender Demo Kit for CAT5 Cables General Description The DS34RT5110-EVKC CAT5 Cable Extender Demo Kit provides a complete HDMI system extension solution with cost effective
More informationCDN503 HIGH DENSITY I/O ADAPTER USER GUIDE
CDN503 HIGH DENSITY I/O ADAPTER USER GUIDE 13050301 (c) Copyright DIP Inc., 1996 DIP Inc. P.O. Box 9550 MORENO VALLEY, CA 92303 714-924-1730 CONTENTS DN503 PRODUCT OVERVIEW 1 DN503 INSTALLATION 1 POWER
More informationM68HC705L4 PROGRAMMER BOARD APPLICATION NOTE
M68HC705L4PGMR JUNE 1992 M68HC705L4 PROGRAMMER BOARD (REVision A PWBs only) APPLICATION NOTE INTRODUCTION This application note describes the programming technique used to program and verify the XC68HC705L4
More informationASH Transceiver 10 mw Power Amplifier Circuit Board
ETSI SRD regulations allow up to 10 mw of transmitter power at 33.92 MHz, and up to 25 mw of transmitter power at 868.35 MHz. For those applications where maximum range is of primary important and low
More informationES-362U PRESETTABLE MASTER TIMER
142 SIERRA ST., EL SEGUNDO, CA 90245 USA (310)322-2136 FAX (310)322-8127 www.ese-web.com ES-362U PRESETTABLE MASTER TIMER OPERATION AND MAINTENANCE MANUAL The ES-362U is a four digit, presettable 100 minute
More informationN8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B.
N8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B. Background. This board is a copy of Andrew Lynch s Version 03 board (with 8 slots) but with added features. Added features: 9 SLOT Active Termination (copied
More informationRC-210 Repeater Controller Assembly Manual
Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net RC-210 Repeater Controller Assembly Manual Hardware Version 3.0 Original Release Date September 13, 2004
More informationH89-Z37 DOUBLE-DENSITY FLOPPY CONTROLLER
H8-Z37 DOUBLE DENSITY FLOPPY CONTROLLER 2015 H89-Z37 DOUBLE-DENSITY FLOPPY CONTROLLER Norberto Collado norby@koyado.com 6/6/2015 Revision History and Disclaimer Revision History Revision Date Comments
More informationApplications Voice Annunciator Taking Clock Voice Alarm Machine Operations Failure Alarm Public Announcement System Automatic Broadcast Equipment s
MP-3 MODULE & RTC DS1307 SHIELD FOR 28-40 DEVELOPMENT BOARD MP3 Shield has been designed for various applications related to voice record and play using MP3 module with memory card storage, this shield
More informationCRD Advanced Product Databook
Advanced Product Databook FEATURES MPC3 compliant (with enhancements), Windows Sound System, DOS Games and AdLib compatible Low Cost Two-Sided Board that Maintains Quality Crystal Single-Chip CS9236 Wavetable
More informationRC-210 Repeater Controller Assembly Manual
Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net RC-210 Repeater Controller Assembly Manual Hardware Version 2.5 Reproduction or translation of any part of
More informationPacific Antenna Easy TR Switch Kit
Pacific Antenna Easy TR Switch Kit Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate
More informationEL Wire sequencer / power supply PART NO
EL Wire sequencer / power supply PART NO. 2206213 The EL Wire sequencer is a EL wire power supply capable of powering 50 plus feet of 2.6mm El Wire and 8 ports controlled by a BS2sx. A menu driven command
More informationInstallation/assembly manual for DCC/Power shield
Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor
More informationIOCards USB Axes Manual. Date:15/03/12 Rev.:2.0
Date:15/03/12 Rev.:2.0 Index: IOCARDS USB AXES MANUAL... 1 INDEX:... 2 INTRODUCTION:... 3 USBAXES:... 3 Outline and components:... 3 Description of connectors:... 3 CONNECTION OF THE PUSHBUTTONS:... 3
More informationPIEXX UT36 px Installation Instructions
PIEXX UT36 px Installation Instructions The PIEXX UT-36 px is a physical and electrical replacement for the original ICOM UT-36 speech synthesizer. UT-36 px Installation The UT-36 px speech synthesizer
More informationBASIC Stamp Activity Board: Features and Specifications
27905 w / Power Supply 27906 w/o Power Supply BASIC Stamp Activity Board: Features and Specifications The BASIC Stamp Activity Board (BSAC) is a demonstration board for Parallax BASIC Stamp computers (BS1-IC,
More informationKDS Channel DMX Controlled Servo Kit
KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an
More informationdigilo A Wideband PLL Synthesizer
digilo A Wideband PLL Synthesizer The digilo is a Wideband Fractional-N / Integer-N PLL Synthesizer based on Maxim's MAX2870 capable of generating signals from 23.5MHz to 6GHz. It measures only 2 x 3 and
More informationMegaAVR-DEVelopment Board Progressive Resources LLC 4105 Vincennes Road Indianapolis, IN (317) (317) FAX
MegaAVR-DEVelopment Board Progressive Resources LLC 4105 Vincennes Road Indianapolis, IN 46268 (317) 471-1577 (317) 471-1580 FAX http://www.prllc.com GENERAL The MegaAVR-Development board is designed for
More informationAVR-M Rev 5 ASSEMBLY
AVR-M Rev 5 ASSEMBLY The AVR_M is a very compact self contained Atmel AVR mcu controller board. It includes an onboard serial programmer (via PC com port), an I2C eeprom and can use a Mega163, Mega16 or
More informationClick-A-Tune. User Manual
Contents Configuring the...2 Transferring data to the...2 with switch configuration...3 with switch matrix up to 3 switches...4 Changing the playback volume...5 Connections... Power requirements (Vin)...
More informationLCD Prototype Circuit on Solderless Breadboard. 840 Pin Solderless Breadboard (http://www.digikey.com/ # ND)
Solderless Breadboard Tutorial Cornerstone Electronics Technology and Robotics I Week 3 Solderless Breadboards: o Solderless breadboards are commonly used in experimentation or to make a prototype of a
More informationDisplay Real Time Clock (RTC) On LCD. Version 1.2. Aug Cytron Technologies Sdn. Bhd.
Display Real Time Clock (RTC) On LCD PR12 Version 1.2 Aug 2008 Cytron Technologies Sdn. Bhd. Information contained in this publication regarding device applications and the like is intended through suggestion
More informationIOCards USB Axes Manual. Date:12/23/14 Rev.:2.2
Date:12/23/14 Rev.:2.2 Index: IOCARDS USB AXES MANUAL... 1 INDEX:... 2 INTRODUCTION:... 3 USBAXES:... 3 Outline and components:... 3 Description of connectors:... 3 CONNECTION OF THE PUSHBUTTONS:... 4
More informationHome Security System with Remote Home Automation Control
Home Security System with Remote Home Automation Control Justin Klumpp Senior Project Hardware Description Western Washington University April 24 2005 Professor Todd Morton Introduction: This document
More informationTranscendent Frequency Counter
Transcendent Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and operate this frequency counter KIT. Features: The transcendent counter has two input channels
More informationCDN502 HIGH DENSITY I/O ADAPTER USER GUIDE
CDN502 HIGH DENSITY I/O ADAPTER USER GUIDE 13050201 (c) Copyright DIP Inc., 1996 DIP Inc. P.O. Box 9550 MORENO VALLEY, CA 92303 714-924-1730 CONTENTS DN502 PRODUCT OVERVIEW 1 DN502 INSTALLATION 1 POWER
More informationStorage Card Interface Kit
Storage Card Interface Kit for MultiMediaCards(MMC) and Secure Digital Cards (SD) MMSD3K The MMSD3K is complete development kit interfaced to a SD or MMC card. This board ideal for projects that involve
More information*on-board power supply capability limited. External battery should be used for higher power servos.
Pan and Tilt Decoder II PART NO. Add affordable Pan and Tilt control to your security cameras using the Pan and Tilt Decoder II and the DFRobot DF05BB Tilt/Pan Kit (5kg), Jameco PN 2144518 or the DAGU
More informationEight Universe Field Programmable Gate Array (FPGA) based E1.31 pixel controller.
Eight Universe Field Programmable Gate Array (FPGA) based E1.31 pixel controller. An FPGA is a poor man s custom digital chip. These chips are much better suited to controlling pixel s, since they can
More informationCONNECT SYSTEMS INCORPORATED 1802 Eastman Ave., Suite 116 Ventura, Ca FLEX II E&M SERIES UNIVERSAL CONTROLLER
CONNECT SYSTEMS INCORPORATED 1802 Eastman Ave., Suite 116 Ventura, Ca. 93003 Phone (805) 642-7184 Fax (805) 642-7271 FLEX II E&M SERIES UNIVERSAL CONTROLLER Hardware Reference Manual Made in U.S.A. Copyright
More informationSymphony SoundBite Reference Manual
Symphony SoundBite Reference Manual Document Number: SNDBITERM Rev. 2.0 09/2008 Contents Section 1, Introduction page 2 Section 2, Functional Blocks page 3 Section 3, Configuration and Connections page
More informationExclusive 2.5 GHz Frequency Counter
Exclusive 2.5 GHz Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and tune this frequency counter KIT. Features: Frequency range from 5 MHz to 2.5GHz Factory
More informationKSZ8081RNB / KSZ8091RNB
KSZ8081RNB / KSZ8091RNB 10Base-T/100Base-TX Physical Layer Transceiver Evaluation Board User s Guide Revision 1.0 / August 2012 Micrel, Inc. 2012 All rights reserved Micrel is a registered trademark of
More informationAssembly Instructions for the KA Electronics RIAA EQ Monitor Switcher
Assembly Instructions for the KA Electronics RIAA EQ Monitor Switcher Install IC sockets EQ Monitor Switcher PC Board Stuffing Guide Place the PC Board on the bench silkscreen side face up. Drop eleven
More informationC S Technology Ltd. cstech.co.uk. DTMF display 32 kit with 2 line x 16 LCD display
C S Technology Ltd cstech.co.uk DTMF display 32 kit with 2 line x 16 LCD display Our DTMF display can display up to 32 characters (16 per line). The display can be cleared by a button (not supplied) or
More informationStorage Card Interface Kit
Storage Card Interface Kit for MultiMediaCards(MMC) and Secure Digital Cards (SD) MMSD3F The MMSD3K is complete development kit interfaced to a SD or MMC card. This board ideal for projects that involve
More informationARC-48: 8-Channel CCD Video Processing Board
ARC-48: 8-Channel CCD Video Processing Board This manual describes the 8-channel CCD video processor board, model ARC-48 Rev. 1A. The board serves two functions - processing and digitizing the video outputs
More informationEvaluates: EV Kits Requiring SPI/ Parallel to USB Interface. INTF3000 Interface Board. General Description. Quick Start. Benefits and Features
INTF3000 Interface Board Evaluates: EV Kits Requiring SPI/ Parallel to USB Interface General Description The INTF3000 interface board is designed to facilitate the interfacing of Maxim s evaluation kit
More informationERICSSONZ LBI-38566B MAINTENANCE MANUAL AUDIO BRIDGE MODULE 19D902458G1 TABLE OF CONTENTS
B MAINTENANCE MANUAL AUDIO BRIDGE MODULE 19D92458G1 TABLE OF CTENTS Page SPECIFICATIS............................................. 1 DESCRIPTI............................................... 1 CIRCUIT ANALYSIS
More informationIFB-325 Portable User Station Talent Electronics User Manual
IFB-325 Portable User Station Talent Electronics User Manual 93507488000 Rev E August / 2007 PROPRIETARY NOTICE The product information and design disclosed herein were originated by and are the property
More informationDMX CONTROLLED RELAY K8072
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 f the means o ol. y b y la a re 2 protoc Control DMX51 wn well-kno ILLUSTRATED ASSEMBLY MANUAL Total solder
More informationCONNECT SYSTEMS INCORPORATED 1802 Eastman Ave., Suite 116 Ventura, Ca FLEX II SERIES UNIVERSAL CONTROLLER
CONNECT SYSTEMS INCORPORATED 1802 Eastman Ave., Suite 116 Ventura, Ca. 93003 Phone (805) 642-7184 Fax (805) 642-7271 FLEX II SERIES UNIVERSAL CONTROLLER Hardware Reference Manual Made in U.S.A. Copyright
More informationDIGITAL AUDIO DELAY MODULE (DADM) INSTRUCTIONS
DIGITAL AUDIO DELAY MODULE (DADM) INSTRUCTIONS Thank you for purchasing the ICS Digital Audio Delay Module! PRODUCT DESCRIPTION The Digital Audio Delay Module (DADM) is an enhanced replacement for the
More informationISOLATED RS-232 TO RS-422/485 CONVERTER
QUICK START GUIDE ICD400A ISOLATED RS-232 TO RS-422/485 CONVERTER 24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM STEP 1 - Specifications Complies with FCC Class B and CE requirements. Withstands
More informationUzebox Kit Assembly Guide
Uzebox Kit Assembly Guide V1.3 Page 1 of 18 Revision History Version Date Author Description 1.0 01-Nov-2012 A.Bourque Initial release 1.1 6-Nov-2012 A.Bourque Minor corrections 1.2 28-Jan-2014 A.Bourque
More informationComtrue Inc. CT7302 EVM D C LQFP 48 Evaluation board Application Note
Overview Comtrue Inc. CT7302 EVM D C LQFP 48 The CT7302 serial chip is a high performance single chip digital audio bridge with sample rate converter. It supports the DSD I/F and DoP on S/PDIF input/output
More informationRC210 Repeater Controller Assembly Manual
Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net http://www.arcomcontrollers.com/ RC210 Repeater Controller Assembly Manual Hardware Version 3.3 Reproduction
More informationAAZ-0914A USB, Blue tooth and Graphic CPU 50MHZ Antenna Analyzer
Fox Delta Amateur Radio Projects & Kits FD- AAZ-0914A AAZ-0914A USB, Blue tooth and Graphic CPU 50MHZ Antenna Analyzer AAZ- 0914A KIT: USB Standalone, Blue tooth standalone and Graphic CPU capable 50MHZ*
More informationSRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
More informationReverse DDS Kit Construction
Reverse DDS Kit Construction This kit is only recommended for home constructors experienced with Surface Mount construction so these notes are for guidance only. Mark out and drill the holes for the SMA
More informationRECORD & PLAYBACK KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT Version 2.1 Build Instructions
More informationSIXTEEN UNIVERSE CONTROLLER
Application Block Diagrams Welcome to one of the most versatile pixel controller available. This controller supports the conversion of multi-cast E1.31 Ethernet to many pixel formats, Renard and DMX. Now
More informationA Programmer for the 68HC705C8 MicroController Figure 1 PROG05 As Built PROG05 User Guide Version C1 Page 1 of 14
A Programmer for the 68HC705C8 MicroController Figure 1 PROG05 As Built PROG05 User Guide Version C1 Page 1 of 14 Table of Contents midon design 1. Introduction...3 2. Description...4 3. Construction...5
More informationisppac-powr1208 Evaluation Board PAC-POWR1208-EV
January 2005 Introduction Application Note AN6040 The Lattice Semiconductor isppac -POWR1208 In-System-Programmable Analog Circuit allows designers to implement both the analog and digital functions of
More informationTEXAS INSTRUMENTS ANALOG UNIVERSITY PROGRAM DESIGN CONTEST MIXED SIGNAL TEST INTERFACE CHRISTOPHER EDMONDS, DANIEL KEESE, RICHARD PRZYBYLA SCHOOL OF
TEXASINSTRUMENTSANALOGUNIVERSITYPROGRAMDESIGNCONTEST MIXED SIGNALTESTINTERFACE CHRISTOPHEREDMONDS,DANIELKEESE,RICHARDPRZYBYLA SCHOOLOFELECTRICALENGINEERINGANDCOMPUTERSCIENCE OREGONSTATEUNIVERSITY I. PROJECT
More informationARES 2 Tone Sequential Tone Decoder Kit Assembly Instructions
Tools Required: ARES Tone Sequential Tone Decoder Kit Assembly nstructions 3/8 Electric Drill Soldering ron Wire Strippers Needle Nose Pliers Wire Cutters Ruler 60/40 Solder Phillips Screw Driver /8, 5/64,
More informationGLiPIC Ver C Assembly manual Ver 1.0
GLiPIC Ver C Assembly manual Ver 1.0 Last Rev 1.1 Oct 30, 2001 Author: Ranjit Diol Disclaimer and Terms of Agreement As with any kit, only the individual parts supplied are guaranteed against defects and
More informationAltera EP4CE6 Mini Board. Hardware User's Guide
Altera Hardware User's Guide 1. Introduction Thank you for choosing the! is a compact FPGA board which is designed based on device. It's a low-cost and easy-to-use platform for learning Altera's Cyclone
More informationPARTS. WARNING: Use of non-midway parts or circuit modifications may cause serious injury or equipment damage! Use only Midway authorized parts.
2))52$' 7+81'(5TM &+$37(5 PARTS WARNING: Use of non-midway parts or circuit modifications may cause serious injury or equipment damage! Use only Midway authorized parts. For safety and reliability, don
More informationADDJOG User Guide 7/30/10. Overview
ADDJOG User Guide 7/30/10 Overview The ADDJOG is a PLC expansion board used to add digital inputs and outputs to a compatible host PLC. The ADDJOG has 64 open collector outputs and 64 non-isolated inputs.
More informationDSP Filter System. Author: Nels Pearson Org Date: July 5, 2007 Rev Date: July 6, Doc Number: AIGO-009
DSP Filter System Author: Nels Pearson Org Date: July 5, 2007 Rev Date: July 6, 2007 Doc Number: AIGO-009 2-13 Table of Contents Introduction...3 Overview...3 A2D Input Filter Board...4 Overview...4 Input
More informationYou need the following components to assemble the Black n Wood Nixie Clock circuit board:
You need the following components to assemble the Black n Wood Nixie Clock circuit board: Quantity Designator Description 1 Battery Battery, CR1220 1 Battery Battery holder 3 Button 1, Button 2, Button
More informationMUSIC SERVER SERVICE MANUAL CONTENTS
MUSIC SERVER CONTENTS Performance Specifications... 2 Notes... 2 Safety Information... 2 Rear Panel... 3 Section Location... 3 Block Diagram... 4 Interconnection Diagram... 5 Front Panel Schematic and
More informationSchematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)
Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by
More informationTEMIC 51T (Temic) EMULATION
Note: To use with frequencies above 40Mhz it will be required to use an emulator board that has been specially modified to obtain high frequency operation and will work only with the POD-51Temic. The EPROM
More informationFreescale Semiconductor, I
M68HC705X4PGMR/D1 August 1991 M68HC705X4 PROGRAMMER BOARD (REVision A PWBs only) INTRODUCTION This application note describes the programming technique used to program and verify the XC68HC705X4 microcontroller
More informationSP336E Evaluation Board Manual Rev 2.1
SP336E Evaluation Board Manual 11-23-10 Rev 2.1 Features Easy Evaluation of the SP336E Transceiver RS-232 and RS-485 Protocols Local or Remote Loop Back testing 10Mbps Differential Transmission Rates Test
More informationAN4373 Application note
Application note Galvanically-isolated 8 channel high-side driver based on the ISO8200B and ISO8200BQ Introduction The STEVAL-IFP015V2 and STEVAL-IFP033V1 evaluation boards work in combination with the
More informationHFRD REFERENCE DESIGN High-Frequency XFP Host Board. Reference Design: (Includes Integrated RS-232 to I 2 C Conversion)
Reference Design: HFRD-18.0 Rev. 7; 11/09 REFERENCE DESIGN High-Frequency XFP Host Board (Includes Integrated RS-232 to I 2 C Conversion) Reference Design: High-Frequency XFP Host Board Table of Contents
More information4.0 Blue LED DCF77 Clock documentation
4.0 Blue LED DCF77 Clock documentation 1. LED Clock Main Board PCB mounting: Mount and solder the eight wire bridges. Mount and solder resistors R16, R18, R20, R22. Mount and solder capacitors C1 C3 (pitch
More informationUSER S MANUAL VER.1. C10D- PARALLEL PORT INTERFACE CARD BOARD Rev. 1
USER S MANUAL VER.1 C10D- PARALLEL PORT INTERFACE CARD BOARD Rev. 1 MARCH 2018 User s Manual Page i USER'S MANUAL TABLE OF CONTENTS Contents Page # 1.0 OVERVIEW... iii 2.0 FEATURES... iii 3.0 SPECIFICATIONS...
More informationRapid40iXL PIC Prototyping PCB User Manual
Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping
More informationCONNECT SYSTEMS INCORPORATED 1802 Eastman Ave., Suite 116 Ventura, Ca FLEX IIIA CONTROLLER
CONNECT SYSTEMS INCORPORATED 1802 Eastman Ave., Suite 116 Ventura, Ca. 93003 Phone (805) 642-7184 Fax (805) 642-7271 FLEX IIIA CONTROLLER Hardware Reference Manual Made in U.S.A. Copyright 2006 By Connect
More informationac wave 2 supply ( analog device )
ac wave 2 supply ( analog device ) «SPECIFIC PRODUCT SECTION» Instruction and user s manual Release 2.1 00/05 REEL S.r.l. Electronic Power Drives Via Riviera Berica, 42 36024 Ponte di Nanto - Vicenza -
More informationUSB-16COMi-M 16-Port RS-422/485 USB Serial Adapter User Manual. Features and Specifications. Power Supply
USB-16COMi-M 16-Port RS-422/485 USB Serial Adapter User Manual The USB to industrial 16-Port RS-422/485 Adapter is designed to make serial port expansion quick and simple. Connecting to a USB port on your
More informationObsolete. LX1800 SMBus TO ANALOG INTERFACE
LX1800 SMBus TO ANALOG INTERFACE TM Page 1 INTRODUCING TO PRODUCT The LX1800 Evaluation Board is available from for evaluating the functionality and performance of the LX1800 SMBus to Analog Interface
More informationEE 354 August 1, 2017 Assembly of the AT89C51CC03 board
EE 354 August 1, 2017 Assembly of the AT89C51CC03 board The AT89C51CC03 board comes as a kit which you must put together. The kit has the following parts: No. ID Description 1 1.5" x 3.25" printed circuit
More informationBill of Materials: Picaxe-based IR Control Module Pair PART NO
Picaxe-based IR Control Module Pair PART NO. 2171014 The IRGEII is an IR (Infra Red) Transmitter and Receiver pair that uses a 38 KHZ frequency of invisible light to communicate simple instructions. The
More informationME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003
ME 3210: Mechatronics Signal Conditioning Circuit for IR Sensors March 27, 2003 This manual and the circuit described have been brought to you by Adam Blankespoor, Roy Merril, and the number 47. The Problem:
More informationKDR00101 DMX Controlled Relay Kit
KDR00101 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 100 ma. The relay contact rating is 10 Amp @ 120 or
More informationONYX-MM-XT PC/104 Format Counter/Timer & Digital I/O Module
ONYX-MM-XT PC/104 Format Counter/Timer & Digital I/O Module User Manual V1.4 Copyright 2009 Diamond Systems Corporation 1255 Terra Bella Avenue Mountain View, CA 94043 USA Tel (650) 810-2500 Fax (650)
More informationDigilab 2 XL Reference Manual
125 SE High Street Pullman, WA 99163 (509) 334 6306 (Voice and Fax) www.digilentinc.com PRELIMINARY Digilab 2 XL Reference Manual Revision: May 7, 2002 Overview The Digilab 2 XL (D2XL) development board
More informationCV Arpeggiator Rev 2 Build Documentation.
CV Arpeggiator Rev Build Documentation. Last updated 8-0-03 The CV Arpeggiator is a modular synth project used for creating arpeggios of control voltage. It utilizes a custom programmed PIC 6F685 micro
More informationImages Scientific OWI Robotic Arm Interface Kit (PC serial) Article
Images Scientific OWI Robotic Arm Interface Kit (PC serial) Article Images Company Robotic Arm PC Interface allows real time computer control and an interactive script writer/player for programming and
More informationMIDI CPU Hardware Rev K. User Manual
MIDI CPU Hardware Revision K User Manual Updated 2010-09-08 Additional documentation available at: http://highlyliquid.com/support/ Page 1 / 18 Table of Contents 1.0 Important Safety Information...2 2.0
More informationDe-Generator DIY sample Synthesizer
De-Generator DIY sample Synthesizer Building instruction 3, the filterboard V 1.03 english Date 10.09.2018 www.tubeohm.com Hello, now we come to the third building instruction. In this manual we will assemble
More informationum-fpu64 Floating Point Coprocessor 28-pin Breakout Board Introduction Bare um-fpu64 28-pin Breakout Board
Floating Point Coprocessor Breakout Board Introduction The breakout board has all of the required connections, and provides access to all um- FPU64 pins. It can be used as a development board or for permanently
More informationIFB-325 Portable User Station Talent Electronics User Manual
IFB-325 Portable User Station Talent Electronics User Manual 9350-7488-000 Rev D 12/2005 PROPRIETARY NOTICE The RTS product information and design disclosed herein were originated by and are the property
More informationKDR00301 DMX Controlled Relay Kit
KDR00301 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 200 ma. The relay contact rating is 10 Amp @ 120 or
More informationRevision: 5/7/ E Main Suite D Pullman, WA (509) Voice and Fax. Power jack 5-9VDC. Serial Port. Parallel Port
Digilent Digilab 2 Reference Manual www.digilentinc.com Revision: 5/7/02 215 E Main Suite D Pullman, WA 99163 (509) 334 6306 Voice and Fax Overview The Digilab 2 development board (the D2) features the
More informationKPIC-0818P (V050919) Devices Included in this Data sheet: KPIC-0818P
Devices Included in this Data sheet: KPIC-0818P Features: Carefully designed prototyping area Accepts 8 pin PIC12 series micro-controllers Accepts 14 and 18 Pin PIC16 series Accepts some 8,14 and 18 pin
More informationDigilab 2E Reference Manual
Digilent 2E System Board Reference Manual www.digilentinc.com Revision: February 8, 2005 246 East Main Pullman, WA 99163 (509) 334 6306 Voice and Fax Digilab 2E Reference Manual Overview The Digilab 2E
More informationPAS 9737/AI-SMT ENGINEERING SPECIFICATION
Document PAS54 Spec Revision C (7/3/8) PAS 9737/AI-SMT ENGINEERING SPECIFICATION 64 CHANNEL, 6 BIT VME ANALOG INPUT CARD PCB Revision D (7/3/8) Additional copies of this manual or other Precision Analog
More informationTwo-wire. Jumper for 12V. J2 Enable Adjust D/A1. Super PLC Warning: Warranty Void if this label is damaged 62256LP-12 CMOS RAM 4.
T100MD-888+ PLC Installation Guide LCD Display Module 1N4007 (optional) + - 12 to 24V DC Power Supply for PLC Contrast Adjust 14-pin LCD Display port Two-wire RS485 + - Jumper for 12V 1000µ F 5 E.Cap (Optional)
More information