WUNDER SA.BI.SRL EN USER MANUAL. MULTIFUNCTIONS ELECTRONIC SCALE MOD. W100 LED. User Manual

Size: px

Start display at page:

Download "WUNDER SA.BI.SRL EN USER MANUAL. MULTIFUNCTIONS ELECTRONIC SCALE MOD. W100 LED. User Manual"

Dinah Wright
5 years ago
Views:

1 MULTIFUNCTIONS ELECTRONIC SCALE MOD. W100 LED User Manual Read this manual carefully before using the instrument W100 SCALE W100 INDICATOR INDICE 2. BEFORE USING PAG SPECIFICATIONS PAG INDICATOR AND KEY FUNCTION PAG INSTALLATION PAG INSTRUCTIONS OF USE PAG SETUP (FUNCTION) CALIBRATION PAG. 5 7 MAINTANANCE AND ASSISTANCE PAG.14 W100LED REV.00 04/12/2016 1

2 2.BEFORE USING 1. Keep the scale dry, keep the scale away from water and rain, Clean the scale if necessary with dry cloth. 2. Keep the scale away from high temperature environment and wet 3. Please recharge the scale when ( ) is on 4. Drop and impact are prohibited 5. If the scale will not be used for a long period of time, please store the scale at dry place and recharge the scale every 3 months 3.SPECIFICATIONS Accuracy Load cell sensitivity range Class Ⅲ level 1.5~3.0mV /V Nonlinear 0.01%F.S System working voltage DC:5V Division value 1/2/5 auto setting Large LCD display connector Sampling serial output way Power Input:AC 120~240V Output:DC 12V/1A 1. Approx. 80mA Power Consunption 2. Approx. 95mA with backlight and RS232 interface Sample Rate 20 times per second (can select Internal resolution 300'000 ~ 600'000 The connector of load cell and indicator: PIN1 : E + PIN2 : E- PIN3 : S+ PIN4 : S - PIN5 : schermo W100LED REV.00 04/12/2016 2

4. INDICATOR AND KEY FUNCTION OFF key: Press and hold the OFF key and the display will show off for 2 seconds then the scale will turn off automatically. ON key: Press the ON key to turn on the scale.

3 4. INDICATOR AND KEY FUNCTION OFF key: Press and hold the OFF key and the display will show off for 2 seconds then the scale will turn off automatically. ON key: Press the ON key to turn on the scale. The scale will start self-adjusting sequence then will stabilize in 0. UNITS / ESC key: UNITS: To select desired weighing unit. ESC : To escape (exit) setting in setup mode. ZERO / key: ZERO : To reset the weight to 0, but the displayed weight value has to be less than ± 2% of maximum capacity. : To move one space to the left or downward in setup mode. TARE / key: TARE : To subtract the container weight. Maximum tare = full capacity : To move one space to the right or upward in setup mode. To the right Net/Gross / key: Net/Gross : To see gross and net weight when the scale is on tare status. All other keys will be disabled when gross weight is activated. : To increase values upward in setup mode. PRINT / key: PRINT : Manually transmitting data through RS232 to computer or printer at normal weighing mode (RS232 setup must be set at keyboard transmission or 232 6) : Works as enter key in setup mode DISPLAY W100LED REV.00 04/12/2016 3

5.INSTALLATION Make sure that: a. Connect the load cell signal and power to the indicator properly. b. Place the scale on a level and strong surface. c. The indicator is turned on. d.

4 5.INSTALLATION Make sure that: a. Connect the load cell signal and power to the indicator properly. b. Place the scale on a level and strong surface. c. The indicator is turned on. d. The ZERO INDICATOR is on. If not, press ZERO to set display to zero. KIT IMBALLO BILICO CON TERMINALE W100: 1. PIATTAFORMA 2.TERMINALE W COLONNA 4.ALIMENTATORE 5. SUPPORTO REGOLABILE TERMINALE 6. MANUALE ISTRUZIONI 6. INSTRUCTIONS OF USE Standard Calibrations: Press the ZERO / key and the PRINT / key in weighing mode to start Standard Calibrations ECF-1 ECF-3 Weight Calibration (Zero and Span) ECF-2 Zero Calibration Span Calibration When the scale is programmed for Approval (LF 6), standard calibration will be locked PRINT /:Net/Gross / : ZERO / : UNITS / ESC:ESC TARE / : ECF-1 Press the key to start or press the ESC key to exit menu and back to weighing mode ECF-2 Press the key to start or press the ESC key to exit menu and back to weighing mode ECF-3 Press the key to start or press the ESC key to exit menu and back to weighing mode W100LED REV.00 04/12/2016 4

5 ECF-1 Weight Calibration : ECF-1 Press the key to start Weight Calibration (Press the ESC key to exit back to weighing mode) CAL2 Press the key to calibrate zero point (Press the ESC key to terminate calibration back to menu ECF-1) kg Use,,,0~9 and then key to enter the weight to be calibrated (Press the ESC key to terminate calibration back to menu ECF-1) kg Place the required weight mass onto the scale as indicated on display and press the key to calibrate the scale (Press the ESC key to terminate calibration back to menu ECF-1) kg Calibration procedure completed and the scale will return back to weighing mode automatically ECF-2 Zero Calibration : ECF-2 Press the key to start Zero Calibration (Press the ESC key to exit back to weighing mode) CAL2 Press the key to calibrate zero point (Press the ESC key to terminate calibration back to menu ECF-2) 0.00kg Zero Calibration procedure completed and the scale will return back to weighing mode automatically ECF-3 SPAN Calibration : ECF-3 Press the key to start Span Calibration (Press the ESC key to exit back to weighing mode) kg Use,,,0~9 and then key to enter the weight to be calibrated (Press the ESC key to terminate calibration back to menu ECF-3) kg Place the required weight mass onto the scale as indicated on display and press the key to calibrate the scale W100LED REV.00 04/12/2016 5

6 (Press the ESC key to terminate calibration back to menu ECF-3) kg Calibration procedure completed and the scale will return back to weighing mode automatically Standard Functions Setup Press the TARE / and the PRINT / key in weighing mode to start Standard Functions Setup UF-1 Internal Value UF-2 Check Weighing UF-3 Auto Power-off UF-4 Standby time UF-5 Hold UF-6 RS232 Output UF-7 UF-8 UF-9 ADC Update Rate Display Condition at Zero Gravitational (G value) Pre-Calibration marks function locked when LF 6 is set as Approval Version PRINT / : Net/Gross / : ZERO / : UNITS / ESC :ESC TARE / : UF-1 Press the key to start or press the ESC key to exit menu and back to weighing mode UF-2 Press the key to start or press the ESC key to exit menu and back to weighing mode UF-3 Press the key to start or press the ESC key to exit menu and back to weighing mode UF-4 Press the key to start or press the ESC key to exit menu and back to weighing mode UF-5 Press the key to start or press the ESC key to exit menu and back to weighing mode UF-6 Press the key to start or press the ESC key to exit menu and back to weighing mode UF-7 Press the key to start or press the ESC key to exit menu and back to weighing mode UF-8 Press the key to start or press the ESC key to exit menu and back to weighing mode W100LED REV.00 04/12/2016 6

7 UF-9 Press the UF-1Press the key to start or press the ESC key to exit menu and back to weighing mode UF-1 Internal Value: key to see the internal value or pressthe ESC key to exit menu and back to weighing mode Press the key to continue or the ESC key to exit back to menu UF-1 Press the key to see the battery voltage or the ESC key to exit back to menu UF-1 UF-1 Use and then keys to continue with other setups or press the ESC key to exit menu and back to weighing mode UF-2 Check Weighing : L Set LO (low) weight H Set HI (high) weight O 000 Program I/O conditions LO set as 0 will clear all check weigh values Check weighing conditions can be set independently for each of the weighing units and counting mode All settings will be saved until manually cleared Last entry will be displayed before setup This function is locked when UF-5 is set as HOLD 1 UF-2 Press the key to start or press the ESC key to exit menu and back to weighing mode L Use,,,0~9 and then key to set LO weight value (Press the ESC key to exit the setup and back to menu UF-2) H Use,,,0~9 and then key to set HI weight value (Press the ESC key to exit the setup and back to menu UF-2) W100LED REV.00 04/12/2016 7

8 O 000 Use,,,0~9 and then key to set I/O SET value (Press the ESC key to exit the setup and back to menu UF-2) UF-2U se and then key to continue with other setups or press the ESC key to exit menu and back to weighing mode UF-3 Auto Power-off : AoFF 00 Auto power-off disable AoFF 01 The scale turns off automatically in 1 minute when the scale is not in operation and weight at 0 Auto power-off timer up to 99 minutes (AoFF01~AoFF 99) Factory default: AoFF 10 UF-3 Press the key to start or press the ESC key to exit menu and back to weighing mode AoFF10 Use and then key to enter Auto Power-off time (Press the ESC key to exit the setup and back to menu UF-3) UF-3 Use and then key to continue with other setups or press the ESC key to exit menu and back to weighing mode UF-4 standby time : HOLD 0 HOLD 1 PCt XXX timexx UF-5 Hold : Hold function off Animal (motion) Hold function To set the range from 001 ~ 100 of the animal hold (for HOLD 1 only) To set times within the hold range (for HOLD 1 only) This function is locked when LF 6 is set as Approval Version Factory default: HOLD 0 UF-5 Press the key to start or press the ESC key to exit menu and back to weighing mode W100LED REV.00 04/12/2016 8

9 HOLD0 Use and then key to select Hold modes (Press the ESC key to exit the setup and back to menu UF-5) UF-5 Use and then key to continue with other setups or press the ESC key to exit menu and back to weighing mode HOLD 1 mode: UF-5 Press the key to start or press the ESC key to exit menu and back to weighing mode HOLD 1 Use and then key to select Hold 1 mode (Press the ESC key to exit the setup and back to menu UF-5) PCt 010 Use 0~9 and then key to enter the hold range (Press the ESC key to exit the setup and back to menu UF-5) time 8 Use and then key to select times (Press the ESC key to exit the setup and back to menu UF-5) UF-5 Use and then key to continue with other setups or press the ESC key to exit menu and back to weighing mode UF-6 RS232 : RS232 disable Stable output Format Stream output Format Manual output Format Stable output Format Stream output Format Manual output Format 2 RS232 Baud rate b 1200 Baud rate 1200 b 2400 Baud rate 2400 b 4800 Baud rate 4800 b 9600 Baud rate 9600 b19200 Baud rate W100LED REV.00 04/12/2016 9

10 b Baud rate Communication Protocol UART signal of EIA-RS232 C Format: 1. Serial output: 1200 / 2400 / 4800 / 9600 / / BPS 2. Data bits : 8 BITS 3. Parity bits : None 4. Stop bits : 1 BIT Start bit Data bits Stop bits Format 1 (232 1 ~ 3 ) : HEAD1 ( 2 BYTES ) HEAD2 ( 2 BYTES ) OL - Over Load ST - Stable NT - Net Weight US - Unstable GS - Gross Weight Fixed 18 BYTES ASCII (kg g t lb) HEAD1, HEAD2, DATA UNIT CR LF Fixed 21 BYTES ASCII (tl.t lboz) HEAD1, HEAD2, DATA UNIT CR LF Fixed 19 BYTES ASCII (pcs) HEAD1, HEAD2, DATA UNIT CR LF Output examples : 1. Example kg Stable net weight : W100LED REV.00 04/12/

11 S T, N T, k g 0D 0A 2. Example lb unstable gross weight : U S, G S, l b 0D 0A 3. Example lb oz unstable gross weight : S T, G S, l b o z 0D 0A 4. Example pcs stable net weight : S T, N T, p c s 0D 0A Format 2 (232 4 ~ 6) : Fixed 12 BYTES ASCII (kg g t lb) DATA UNIT CR LF Fixed 15 BYTES ASCII (tl.t lboz) DATA UNIT CR LF Fixed 13 BYTES ASCII (pcs) DATA UNIT CR LF Output examples : 1. Example kg stable net weight : k g 0D 0A 2. Example lb unstable gross weight : l b 0D 0A 3. Example lb oz unstable gross weight : l b o z 0D 0A 4. Example pcs stable net weight : p c s 0D 0A UF-6 Press the key to start or press the ESC key to exit menu and back to weighing mode W100LED REV.00 04/12/

12 232 0Use and then key to enter RS232 output format (Press the ESC key to exit the setup and back to menuuf-6) b9600 Use and then key to select baud rate (Press the ESC key to exit the setup and back to menu UF-6) UF-6 Use and then key to continue with other setups or press the ESC key to exit menu and back to weighing mode UF-7ADC Update Rate : SPEEd 1 Standard speed 15 hz SPEEd 2 High speed 30 hz SPEEd 3 Low speed 7.5 hz This function is locked when UF-5 is set as HOLD 1 This function is locked when LF 6 is set as Approval Version Factory default: SPEEd 1 UF-7 Press the key to start or press the ESC key to exit menu and back to weighing mode SPEEd1 Use and then key to select ADC speed(press the ESC key to exit the setup and back to menu UF-7) UF-7 Use and then key to continue with other setups or press the ESC key to exit menu and back to weighing mode UF-8 Zero Weight Display Condition : ZP 0 Off ZP 1 One division not to display at zero ZP 2 Two divisions not to display at zero ZP 3 Three divisions not to display at zero ZP 4 Four divisions not to display at zero ZP 5 Five divisions not to display at zero This function is locked when UF-5 is set as HOLD 1 This function is locked when LF 6 is set as Approval Version W100LED REV.00 04/12/

13 Factory default: ZP 0 UF-8 Press the key to start or press the ESC key to exit menu and back to weighing mode ZP0 Use and then key to select how many divisions not to display at zero (Press the ESC key to exit the setup and back to menuuf-8) UF-8 Use and then key to continue with other setups or press the ESC key to exit menu and back to weighing mode UF-9 Standard Gravitational (G value) Pre-Calibration: Approval Model: When the CAL switch is at OFF, 10 gravitational values can be entered and can be also recalled for reference. After 10 gravitational values have been filled, the scale will only allow recalling previous 10 values (-00- ~ -09-) for reference and adding new value will not be allowed. Internal Gravitational Calibration or LF1 Internal Weight Calibration has to be done to erase previously entered values. Non-approval Model: Even the scale allows to do the Standard Calibration, Gravitational Calibration can help to provide accurate scale when end users received it without all the trouble to recalibrate thescale. Pre-calibration is allowed when the scale is setup as non-approval model or the CAL switch is at ADJ position. Gravitational value will be saved at -00- and will be replaced each time a new value has been entered. Sender G value: Set it before Weight Calibration Recipient G value: Set it after Weight Calibration The G value will be denied when the value is greater than (Polar G value) or less than (Equator G value) Factory Default: UF-9 Press the key to start or press the ESC key to exit menu and back to weighing mode -03- The display will show the last value for 1 second Use keys to see previous entered values. The display will stay at 00 if no value has been entered W100LED REV.00 04/12/

14 -02- The display will show the last value for 1 second Use keys to see previous entered values. The display will stay at 00 if no value has been entered Press the key to start (Press the ESC key to exit the setup and back to menu UF-9) Use 0~9 and then key to enter the Gvalue (Press the ESC key to exit the setup and back to menu UF-9) Press the key to confirm the G value UF-9 Use and then key to continue with other setups or press the ESC key to exit menu and back to weighing mode 7. MAINTENANCE AND ASSISTANCE For better and longer duration of the product it should receive thorough general cleaning periodically. The instrument must be cleaned with a soft cloth moistened with water or neutral detergent, without using solvents or abrasive substances. If the instrument remains idle for a long period, remove the batteries from the terminal. During shipping, make sure not to subject the instrument to blows or excessive mechanical stress. In case of repairs or assistance, contact your dealer or an authorised service centre W100LED REV.00 04/12/

CONTENTS. PRECAUTIONS Introduction Installation... 7

CONTENTS. PRECAUTIONS Introduction Installation... 7 2 CONTENTS PRECAUTIONS... 4 1. Introduction... 6 2. Installation... 7 2.1 Unpacking... 7 2.2 Illustration of the installation for plastic shied... 7 2.3 Selecting the location... 8 2.4 Leveling the scale...