User Manual VDH-GK350A 2016 SEP V1.0

Transcription

1 User Manual VDH-GK350A 2016 SEP V1.0

2 WARNING Do not expose the DVR under the sunlight, heat or wet environment while installation. As it could decrease the performance of DVR and damage the machine. Do not touch the power plug or case with wet hands as this could result electric shock. Do not forcedly bend or put heavy object on power cable as this could result in injury to personal or equipment. Do not operate with damaged power cord or loose electrical outlet as this could result in electric shock or accident. Please use individual power instead of share electrical outlets with other electrical equipment as this could result in damage or accident. Do not attempt to service this DVR by yourself as it may expose you to dangerous voltage or other hazards. Please refer all service to the qualified servicing distributor. Please do not remove the machine housing during operation. It may cause electric shock or accidental injury. CAUTION Do not place the machine on an uneven surface or it would decrease the DVR efficiency or malfunction. Avoid any shock or bumping of the DVR while recording. Improper handling could damage the system. CAUTION Make sure the voltage selector switch is set to appropriate setting before plug in!

3 CONTENTS A. DVR system operation Login Information Device Status Map Playback Setting System information HARD DISK INFORMATION Network Account PROTOCOL Setting value Upgrade i

4 A. DVR system operation 1. Login Input GK350A, then into web page. default IP : username: admin password : admin Note: IE 11 browser supported only, below not supported. 2. Information Assign VG01 connected to GK350A, will see VG01 on line. 1

5 Pick up the devices added to GK350A. After above steps, user can check the status of all devices. 2

6 3. Device Status off line on line Click, it shows information like above picture ❶ ❷ ❸ ❹ 1. Device ID : cannot be changed 2. Driver : default is unknown, user can revise as user s need. 3. Vehicle ID: User can revise as user s need. 4. Recording: Default value is on, if no recording, pls check this whether it is on or off. 3

7 Click X, device will ask you remove or not. If choose cancel like below If Choose remove, like below. 4

8 4. Map click on map, it will show Google map. Click on Device ID, it will show devices on left list totally. Choose device item, it show device s information on left list. 5

9 5. Playback click on playback. Click on Device ID, it will show devices on left list totally. Click on device you choose, then will show date, select the time you want for playback. 6

10 After above steps, it will show live image & device s location. 6. Setting 6.1 System information It offers device s information as below. 6.2 HARD DISK INFORMATION It shows HDD model no., serial no.,status, capacity. 7

11 6.3 Network Network connection setting by manual Ethernet : Either Static or PPPOE Static Mode IP address : can be revised, default is Sub netmask : can be revised, default is Gateway: can be revised, default is DNS SERVER #0 : can be revised, default is DNS SERVER#1 : can be revised, default is PPPOE MODE USERNAME: TELECOM s OFFER password : TELECOM s OFFER WANIP: connect successfully, it will show public IP. 8

12 6.3.3 DDNS Default is off, or choose on. Provider : 3 items CCTVDVR, NO-IP, My online portal Server : Input DDNS IP address, if choose CCTVDVR,it is blank USER: input applied DDNS s username password : input applied DDNS s password NTP TIME ZONE: Select current zone. NTP Server Input local NTP server IP address, default is watch.stdtime.gov.tw 9

13 6.4 Account click one of them on the left list to define the authority. 10

14 Choose admin : The level can revise the username & password. Default : admin /admin (username/password ), press save after revision. Select user : authority is to define username/password & live monitoring, users must select device ID, then press save. 11

15 6.5 PROTOCOL GPS receiver port no : can be revised, default is Command port no. can be revised, default is Streaming port no. : can be revised, default is 8901 If using router, these 3 ports must be switched on. 6.6 Setting value 12

16 Import configuration : Select the setting value from PC as below dialog. Export configuration : choose PC s drive where save the setting value. 13

17 Default returned : press Restore. If user needs original network setting, just mark on keep network setting, then restore. 6.7 Upgrade choose the file from PC s drive. 14

18 Select the firmware file, then upload, meanwhile, will show percentage of process. It will show green characteristic like below after upgrade, means successful operation. Click on, can know who is login. Click on, will find latest 20 records maximum after HDD format. 15

19 Click on, language is either English or Chinese 16

20 Manufacturer FUHO TECHNOLOGY CO., LTD NO.30 LANE 726 JINMA RD SECTION 3, Chang Hua City Taiwan