INTEGRATED ROUTING SYSTEM PACK IXS-6600-C IXS-6700-C INTEGRATED ROUTING SYSTEM IXS-6600 IXS-6700 IKS-6030M IKS-A6011 IKS-A6015 IKS-A6050 IKS-A6061 IKS-V6010M IKS-V6010SD IKS-V6050M IKS-V6050SD IKS-V6060M IKS-V6060SD IKS-RS6010 IKS-RS6060 SYSTEM SETUP MANUAL 1st Editio
Note o System Settig Actual operatio may be differet from the operatio described i this maual by the software upgrade. IXS-6600/6700
Table of Cotets Maual Structure 3. Cofirmatio of Fuctio Purpose of this maual... 3 Related mauals... 3 Trademarks... 3 Termiology... 4 Cotets... 4 1. Overview 3-1. Outlie...3-1 3-2. Fuctio Check... 3-1 3-2-1. Fuctio Check after Power O...3-2 3-2-2. Fuctio Check with Meu Item [V : DISPLAY UNIT STATUS]... 3-2 3-2-3. Fuctio Check with Meu Item [W : SYSTEM STATUS LOG]...3-2 3-2-4. System Status Log...3-3 1-1. What is the Itegrated Routig System?...1-1 1-2. Fuctios of the IXS-6600/IXS-6700 Itegrated Routig System...1-1 1-3. Compatibility betwee the S-BUS P1 (S-P1) Type ad S-BUS P2 (S-P2) Type...1-2 1-4. Costituet Devices of Routig Switcher System...1-3 1-5. Cotrols by Routig Switcher System...1-4 1-5-1. Specificatios ad Fuctios of Cotrol Port...1-4 1-5-2. S-BUS Cotrol...1-5 1-5-3. RS-422A Cotrol...1-6 1-6. System Coectio Example...1-7 1-6-1. S-BUS Cotrol System Coectio Example...1-7 1-6-2. REMOTE2 (RS-422A) Cotrol System Coectio Example...1-8 4. Techical Iformatio 4-1. Cross-poit Switchig Sequece...4-1 4-2. Cocept of a New System Eabled by the Itroductio of the BZR-IR830...4-4 4-3. RS-244 Router Cotrols...4-13 Appedix A Fuctios ad Meu Items Appedix B Glossary 2. Setup 2-1. Itroductio...2-1 2-1-1. Flow Chart of Setup Procedure...2-1 2-1-2. Symbols Used i This Maual...2-2 2-2. Preparatio...2-2 2-3. Display Screes, ad Movig betwee the Display Screes...2-4 2-4. Settig Items of the Primary Statio...2-7 2-5. Settig Items of the Secodary Statio...2-28 IXS-6600/6700 1
Maual Structure Purpose of this maual This maual is the system setup maual of Itegrated Routig System ISX-6600/IXS-6700. It cotais iformatio o the iitial settigs ad cofirmatio of fuctio of the software whe istallig the IXS-6600/IXS-6700. This maual is iteded for system ad service egieers. But operators ca also refer to it whe settig ad chagig the system. Refer to istallatio maual supplied with IXS-6600/IXS-6700 for iformatio o istallig the hardware. Related mauals Besides this System Setup Maual, the followig mauals are prepared for IXS- 6600/IXS-6700.. Operatio Maual (Supplied with IXS-6600/IXS-6700) This maual describes the applicatio ad operatio of IXS-6600/IXS-6700.. Istallatio Maual (Supplied with IXS-6600/IXS-6700) This maual describes iformatio o IXS-6600/IXS-6700 istallig.. Maiteace Maual (Available o request) This maual describes the iformatio that premises the parts level service (adjustmet, parts list, diagrams, etc.). If this maual is required, please cotact your local Soy Sales Office/Service Ceter.. Protocol Maual (Available o request) This maual describes the protocol for cotrollig this uit. The maual below is provided for the protocol that this uit ca support. If this maual is required, please cotact your local Soy Sales Office/Service Ceter. S-BUS PROTOCOL AND COMMAND SPECIFICATIONS (S-BUS remote termial cotrol protocol) Part No.: 9-977-477-1X Trademarks Trademarks ad registered trademarks used i this maual are follows.. Etheret is a registered trademark of Xerox Corporatio.. IBM ad AT are registered trademarks of Iteratioal Busiess Machies Corporatio.. Microsoft ad Widows are registered trademarks of Microsoft Corporatio.. Petium is a registered trademark of Itel Corporatio. IXS-6600/6700 3
Termiology. Routig Switcher Idicates the ame of the product category.. Itegrated Routig Switcher (IXS-6600/IXS-6700) This is the product ame of IXS-6600/IXS-6700. The product category of the Itegrated Routig Switcher belogs to Routig Switcher.. Routig Switcher System Idicates the cofiguratio where multiple devices are coected to the Routig Switcher. (Refer to 1-6. System Coectio Example.) Cotets The followig is a summary of all the sectios of this maual. Sectio 1 Overview This sectio outlies the basic structure of the routig switcher system ad cotrol mechaism usig the S-BUS. Sectio 2 Setup This sectio explais the settig meus of the primary statio ad the secodary statio ad how to set each item i the meus, i detail. Also it explais how to backup the table data. Sectio 3 Cofirmatio of Fuctio This sectio explais the error messages ad how to check the operatios of the system after completig settig. Sectio 4 Techical Iformatio This sectio explais the followig cotets:. Switchig sequece of the cross-poits. Cocept of a ew system eabled by itroducig the optioal BZR-IF830 software. Cotrol of the RS-422 ROUTER Appedix A Fuctios ad Meu Items Describes the fuctios ad meu items list. Appedix B Glossary Describes the termiology that is used i this maual. 4 IXS-6600/6700
Sectio 1 Overview 1-1. What is the Itegrated Routig System? Itegrated routig system is the system that has the fuctios of switchig ad cotrol of sigals usig routig switchers. The mai devices that costitute the itegrated routig system are the routig switchers that switch the sigals i accordace with the commads give by the host cotrol equipmet (host computer, etc,.) or the commads from the remote cotrol pael (routig switcher cotrol uit), a persoal computer that realizes the various setups that are required for cofigurig ad operatig the itegrated routig system, ad the remote cotrol pael to perform the sigal switchig operatios ad to display the ames of the selected sigals. 1-2. Fuctios of the IXS-6600/IXS-6700 Itegrated Routig Sstem The IXS-6600/IXS-6700 itegrated routig system has the followig fuctios. Secret fuctio It hides all of the iput systems from the remote cotrol pael so that the set cross-poits caot be switched. Protect fuctio Each output sigal ca be protected so that it will ot be switched by other remote cotrol paels. Cross-poit disable settig fuctio The iput chaels that ca be selected by operator, ca be limited for each output system so that the specific iput chaels ca be output to the specified output system oly. Password fuctio Password ca be set so that the accessible operators ca be limited by the password. Namig fuctio Names ca be give to the iput ad output termials so that the coectio sigals ca be idetified. Names ca be give by either oe of the followig two methods: Oe method is Type ame (equipmet ame such as VTR or camera) + umber (example: VTR1). The other method is to give a Descriptio ame havig arbitrary16 characters. The give ame ca be displayed o the optioal display uit ad the remote cotrol pael. Virtual mappig fuctio Cross-poit matrix ca be mapped o a virtual matrix. Free assigmet fuctio To each coector ame, a differet coector umber ca be assiged o each level. Tie lie fuctio You ca eable the system to automatically select the sigal lies up to three routig switchers. Phatom fuctio You ca switch several cross-poits at the same time. IXS-6600/6700 1-1
Self-diagosis fuctio Presece or absece of iput/output sigals ad occurrece of error ca be set to a persoal computer that is coected to the primary statio ad display them. Other fuctios. IXS-6600/IXS-6700 has the built-i system cotroller (primary statio fuctio). Therefore, there is o eed to prepare a cotroller to cotrol the routig system.. Up to 8 levels ca be assiged.. Whe the optioal Subet Iterface (BZR-IF810) are used, a maximum of 60,000 devices ca be cotrolled by a sigle routig switcher system. The IXS-6600/IXS-6700 does ot have the cotrol fuctio for the moitorig S-BUS system. 1-3. Compatibility betwee the S-BUS P1 (S-P1) Type ad S-BUS P2 (S-P2) Type There are two types of Soy Routig Switcher. Oe is the S-BUS P1 type (abbreviated as S-P1 hereafter) that supports the virtual matrix size 512, ad the other is the S-BUS P2 type (abbreviated as S-P2 hereafter) that supports the virtual matrix size 1024. The IXS-6600/IXS-6700 is the S-P2 type. The S-P2 type has the upward compatibility with the S-P1 type but has the several limitatios. The S-P2 type is realized by extedig the type umber of the termial ames from 16 to 32, ad by chagig the data structure of the termial ames. The 16 types of the termial umber data that are used i the S-P1 type, do ot have compatibility with the 32 types of termial umber data that are used i the S-P2 type. Therefore, the S-P2 type has two types of data i.e., both the 16 type data ad the 32 type data for each termial of termial umber 1 to 512. The 16 type data must be used for the termial umber of 1 to 512 whe the S-P1 type display uit (BKS- R3280/R3281) ad the remote cotrol pael (routig switcher cotrol uit) are used i the system. The 32 type data must be used for the termial umbers of 513 to 1024. Whe all of the display uits ad the remote cotrol paels withi the system are of the S-P2 type, the termial umbers of 1 to 512 must be set to the 32 type data. Whe use of the remote cotrol paels of the S-P1 ad S-P2 types are mixed, use of the S-P1 type remote cotrol pael is limited withi the rage of termial umber from 1 to 512. I such a case, the S-P2 type remote cotrol pael ca hadle the 32 type data with the termial umber of 513 to 1024. This maual describes iformatio of oly IXS-6600/IXS-6700 that is the S-P2 type machie. For the iformatio o the S-P1 type machies, refer to the followig maual.. Istallatio Maual (Software) : 3-194-351-xx It is supplied with the routig switcher of the S-P1 type machie. m All of the followig models curretly available belog to the S-P2 device.. Routig switcher: IXS-6600/IXS-6700/HDS-X5800. Remote cotrol pael: BKS-R1617/BKS-R168/BKS-R3216/BKS-R3219/BKS-R3220 1-2 IXS-6600/6700
1-4. Costituet Devices of Routig Switcher System The routig switcher system cosists of the followig four types of equipmet.. Routig switcher cotroller (HKSP-R80) It cotrols the sigal switchig of the routig switcher i accordace with the commads from the host cotroller (such as host computer) ad remote cotrol pael.. Routig switcher (IXS, HDS, DVS, BVS series) It switches sigals accordig to the commad from the cotroller (such as host computer) ad the remote cotrol pael. Varied switchers are available for differet types of sigals such as serial digital video, digital audio, time code, RS-422A, etc.. Remote cotrol pael (routig switcher cotrol uit) (BKS-R series) It switches sigals ad displays the ame of the selected sigal. It is sometimes simply called as remote cotrol pael.. Persoal computer A persoal computer is required i order to establish the various setups that are ecessary for cofigurig ad ruig the routig switcher system usig a termial emulator. The setup data are backed up ad uploaded with the BZR-20 that is supplied with the IXS-6600/IXS-6700. A persoal computer havig the followig specificatios is recommeded for use with the routig switcher system.. IBM PC/AT compatible persoal computer. Widows XP (Eglish versio or Japaese versio). CPU Itel Petium Processor equivalet or higher. Clock 233 MHz or higher. RS-232C port or Etheret is istalled.. Termial emulator (VT100 or higher) is istalled.. The codes of F1 to F5 are already set. For the code settig procedure, refer to Sectio 2-2.. BZR-20 (V2.11 or higher) is istalled. For the BZR-20 istallatio procedure, refer to the Istallatio Maual i the CD-ROM supplied with the IXS-6600/IXS-6700.. Microsoft Excel is istalled. IXS-6600/6700 1-3
1-5. Cotrols by Routig Switcher System 1-5-1. Specificatios ad Fuctios of Cotrol Port The IXS-6600/IXS-6700 itegrated routig system is equipped with four kids of remote ports REMOTE 1 (stadard S-BUS), REMOTE 2 (RS-422A), REMOTE 3 (RS-232C), ad NETWORK (Etheret). The specificatios ad fuctios of the cotrol ports are as follows. REMOTE 1 BNC 75 Z Protocol : S-BUS cotrol PROTOCOL Data Trasfer Speed Max Cable Legth S-BUS 312.5 kbps/1250 kbps 500 m/125 m (BELDEN 8281 cable or equivalet) Fuctio : Cotrol of the equipmet is executed by the S-BUS data lik. The various types of equipmet related to the cotrol, such as remote cotrol pael, routig switcher, ad display uit are coected to this data lik. REMOTE 1 is the remote cotrol termial that is always istalled i the machies that are to be cotrolled by the S-BUS cotrol. REMOTE1 is sometimes simply called REMOTE for uits havig this remote port oly. REMOTE 2 D-sub 9-pi Protocol : RS-422A (Trasfer speed : 38.4 kbps, data bit : 8 bits, parity : EVEN) CART++ Protocol Cotrollable size 16 x 16 256 x 256 4093 x 4093 CART O CART+ O O _ CART++ O O O Fuctio : With this, the oe-to-oe port commuicatio betwee two uits is performed. It is used whe a Soy routig switcher is used as a simple matrix switcher whe receivig cotrols from the cotroller of other maufacturers via RS-422A. 1-4 IXS-6600/6700
REMOTE 3 D-sub 9-pi Protocol : RS-232C (Trasfer speed : 38.4 kbps, Data bit : 8 bits, No Parity, No check) Fuctio : Whe coected with a persoal computer, it performs the system setups, program dowloadig, setup data dowloadig/uploadig, ad sigal switchig. I order to perform system setup ad program dowloadig, the optioal termial emulator program must be istalled i a persoal computer. I order to perform the setup data uploadig/dowloadig ad the sigal switchig, istall the BZR-20 ad the BZR-21 that are supplied with the IXS-6600/IXS-6700 ad use them. NETWORK RJ-45 8-pi modular jack Protocol : TCP/IP trasfer (100BASE-TX) Fuctio : Set the IP address ad cotrol the routig switcher system from remote locatio. This fuctio is ot suited to the real-time operatio because commuicatio may take some time depedig o the etwork eviromet. Fuctios other tha that, remai the same as those of REMOTE 3. 1-5-2. S-BUS Cotrol The IXS-6600/IXS-6700 uses the Soy uique remote cotrol protocol called S-BUS (Soy serial bus) for cotrollig the switcher system. I the S-BUS cotrol, the multiple routig switchers ad remote cotrol paels are coected to a sigle bus lie to form a cotrol etwork called the S-BUS data lik. The devices o the S-BUS data lik are desigated to a primary statio which cotrols the whole system (oly oe uit is set as this) ad secodary statios. The primary statio ot oly cotrols the commuicatio betwee the secodary statios, it coverts the output request sigals from the secodary statio after covertig them i accordace with the iterally set coditios. Be sure to attach the 75 Z termiator to all of the u-used S-BUS lie coector regardless of the primary/secodary statios. IXS-6600/6700 1-5
Features of S-BUS Cotrol System The mai features of the S-BUS cotrol are as follows.. LAN type cotrol sigal commuicatio usig oe 75 Z coaxial cable (S-BUS lie). The primary statio ca cotrol up to 253 uits of routig switchers ad remote cotrol paels usig multiple S-BUS lies.. The coaxial cable ca be exteded to 500 m. (BELDEN 8281 cable or equivalet). Up to 128 uits of routig switchers ad remote cotrol paels ca be coected to oe S-BUS lie.. Without stoppig the system, the switchers ad remote cotrol paels ca be added to the S-BUS lie or removed from it. Basic Cofiguratio of S-BUS Cotrol System S-BUS cotrol is cofigured as follows. Name Equipmet Quatity Fuctio Primary statio Routig switcher cotroller 1 Commuicatio cotrol i data lik Routig switcher (P) *1 1 Secodary statio Remote cotrol pael ad 253 (max.) Implemets commuicatio cotrol of routig switcher (S) *2 idividual equipmet. Persoal computer Termial emulator BZR-20 1 Implemet the various system setup ad dowload/upload of the settig data. *1 : It meas a switcher whose P/S switch Note) o CPU board is set to the P positio. *2 : It meas a switcher whose P/S switch Note) o CPU board is set to the S positio. 1-5-3. RS-422A Cotrol The IXS-6600/IXS-6700 ca be cotrolled from a exteral cotrol equipmet that is coected to the REMOTE2 (D-sub 9-pi) coector with the RS-422A iterface. I additio to it, the protocol ca be exteded so that up to 4093 iputs x 4093 outputs x 8 levels ca be cotrolled by the remote cotrol. The exteded protocol is the CART++ that has the cotrol size of 256 or less ad is compatible with the existig protocol (CART, CART+). Whe the IXS-6600/IXS-6700 is assiged to the primary statio, the protocol is fixed to the S-BUS coversio mode that coverts the received RS-422A commad to the S-BUS protocol. Whe the IXS- 6600/IXS-6700 is assiged to the secodary statio, the protocol is fixed to the Direct mode i which the received RS-422A commads are used to cotrol the receivig statio oly. m. I the direct mode, the protect ad secret fuctios set o the S-BUS protocol are ot available.. I the S-BUS coversio mode, the protect ad secret fuctios set o S-BUS protocol are available. However, these fuctios caot be set from the 9-pi remote cotrol ad the cotets of the settig caot be checked from the 9-pi remote cotrol. Note) : I IXS-6600/IXS-6700, P/S switch o CPU board meas S1203-3 o the CA-65 board. 1-6 IXS-6600/6700
1-6. System Coectio Example 1-6-1. S-BUS Cotrol System Coectio Example The coectio example of the S-BUS data lik usig the IXS-6600/IXS-6700 as the primary statio is show. The IXS-6600/IXS-6700 does ot have the cotrol fuctio of the moitorig S-BUS system. Maximum 16 equipmet Termial Persoal computer (Termial emulator) Termial Persoal computer (Termial emulator) : S-BUS : Sigal system lie : Etheret : T-type bridge (A) : T-type bridge (B) Primary statio Level 1 Itegrated routig system IXS-6700 (P) DATA Etheret hub Video : 75 Z termiator *2 : Layer of matrix Destiatio VTR Video REMOTE1 A REMOTE1 B1 REMOTE1 B2 REMOTE1 C Audio chael 1/2 Audio chael 3/4 Time code Secodary statio Level 2 Level 3 Level 4 Level 8 Audio routig switcher (S) *1 Audio routig switcher (S) *1 Time code routig switcher (S) *1 Each routig switcher (S) *1 Source VTR Audio Chael 1/2 Audio Chael 3/4 Time code Subet Cotroller Tertiary statio Remote cotrol pael Subet Cotroller Display uit Maximum 128 equipmet Remote cotrol pael Remote cotrol pael Remote cotrol pael Remote cotrol pael Display uit Display uit Display uit Either oe of the REMOTE 1 coectors of the secodary statio routig switchers ca be used. *1 : (S) idicates the secodary statio. For the secodary statios, set the statio ID i the rage of ID = 2 to 254 i the maer that the same ID must ot be duplicated. *2 : Istall the 75 Z termiators to the T type bridge of the last device o the S-BUS data lik ad to the uused REMOTE 1 coector. IXS-6600/6700 1-7
1-6-2. REMOTE2 (RS-422A) Cotrol System Coectio Example The coectio example of the REMOTE 2 (RS-422A) cotrol system is show. S-BUS coversio mode coectio example Direct mode coectio example RS-422A REMOTE2 RS-422A Cotroller (Host CPU) Cotroller (Host CPU) Subet cotroller (P) REMOTE1 Routig switcher (S) Routig switcher (S) Routig switcher (S) REMOTE2 Routig switcher (S) Routig switcher (S) Routig switcher (S) Routig switcher (S) Routig switcher (S) S-BUS Routig switcher (S) Routig switcher (S) Routig switcher (S) Routig switcher (S) Routig switcher (S) : S-BUS : RS-422A : 75 Z termiator : T tridge : Stadard uits makig up Soy routig system (P) (S) : The settig of P/S switch o the CPU board. 1-8 IXS-6600/6700
Sectio 2 Setup 2-1. Itroductio 2-1-1. Flow Chart of Setup Procedure Flow chart of the setup procedure is show. Refer to Sectio 2-2. Iitial settig Set the P/S switch o the CPU board to the [P] positio. Set the codes F1 to F5. Coect a persoal computer. Tur o the mai power. Refer to the Istallatio Maual. Set the IP address. Refer to Sectio 2-5. Iitialize the settig K: RESET TO DEFAULT TABLE Refer to Sectio 2-4. Set the respective items of the primary statio. P: CHANGE PASSWORD T: SET CLOCK A: SET CONTROL AREA B: SET SOURCE/DEST TYPE J: NAME STYLE C: SET DESTINATION NAME D: SET SOURCE NAME * Modificatio * : Meu item A ad I do ot eed to be set whe BZR- IF830 is ot used. Refer to Sectio 2-5. Set the respective items of the secodary statio. A: SET UNIT LOCATION Z: SET SIGNAL W: SAVE CURRENT TABLE Restart up the primary statio equipmet. Refer to the Istallatio Maual. Back up the table data. E: SET LEVEL TABLE S: SET SOURCE ASSIGNMENT Ed L: SET PHYSICAL ASSIGNMENT I: SET INDEX NUMBER * H: SET GLOBAL PHANTOM M: SET INHIBIT TABLE F: SET ACTIVE UNIT NUMBER Whe Descriptio Name is selected Whe Type + Num Name is selected N: SET DESCRIPTION NAME GROUP O: SET TIE LINES R: CALL SECONDARY STATION IXS-6600/6700 2-1
2-1-2. Symbols Used i This Maual The symbols used for the cotrol termial emulator keys i this maual are as follows.. All keys are eclosed i boxes. (Ex. [Ctrl], [Eter]). The umerical keys i the text mea keys [0] to [9].. The alphabet keys i the text mea keys [A] to [Z].. The cursor key i the text mea the [(], [)], [&], ad [*] keys.. Whe two keys are to be pressed together, they are joied by the _. (Ex. [Ctrl] _ [X]). I IXS-6600/IXS-6700, P/S switch o CPU board meas S1203-3 o the CA-65 board. 2-2. Preparatio Whe the IXS-6600/IXS-6700 is Used as the Primary Statio 1. Settig the primary statio Switch the P/S switch o CPU board of IXS-6600/ IXS-6700 to the P side. Whe settig the primary statio, oly a sigle primary statio ca be set o a sigle S-BUS remote lie. If two or more primary statios are set o a sigle S-BUS remote lie, the routig switcher system will ot work properly. 2. Settig the secodary statio Set the statio ID (2 to 254). (Refer to maual of the secodary statio.) 3. Coect the IXS-6600/IXS-6700 to the secodary statio. (Refer to Sectio 1-6-1.) 4. Set a persoal computer. (Settig the F1 to F5 codes.) Set the codes of F1 to F5 i accordace with the followig table referrig to the documet of termial emulator. Key Name Commad HEX Data F1 F1 ESC [ 17 ~ 1B, 5B, 31, 37, 7E F2 F2 ESC [ 18 ~ 1B, 5B, 31, 38, 7E F3 F3 ESC [ 19 ~ 1B, 5B, 31, 39, 7E F4 F4 ESC [ 20 ~ 1B, 5B, 32, 30, 7E F5 F5 ESC [ 21 ~ 1B, 5B, 32, 31, 7E *ESC =16 hexadecimal umber 1B 10 decimal umber 27 5. Coectig the IXS-6600/IXS-6700 to the persoal computer I the case of RS-232C : Use the RS-232C cable ad coect the persoal computer to the REMOTE3 coector. I the case of Etheret : Use the dedicated cable ad coect the LAN hub to the DATA coector. 6. Settig the commuicatio coditios of the persoal computer I the case of RS-232C : Trasfer speed : 38.4 kbps, Data bit : 8 bits, No parity, No check. I the case of Etheret : Set the IP address of the termial emulator to the same IP address of the IXS-6600/IXS-6700. Set the port No.1001. 2-2 IXS-6600/6700
7. Turig o the power. Tur o the power of all the equipmet o the S-BUS data lik. The system status scree appears o the persoal computer moitor. (Refer to Sectio 2-3.) Wait for about oe miute or more after turig o the power, before startig the settig. Operatio of the equipmet may be ustable immediately after the power is tured o. 8. Let the primary statio meu scree appear o the display. (Refer to Sectio 2-3.) Whe the [Ctrl] _ [X] are pressed o the system status scree, the display shows the primary statio meu scree. Perform the respective settigs that are show i Sectio 2-4 from the primary statio meu scree. Whe the system is coected usig Etheret, a maximum of 16 people ca work to set up at the same time. However, the same item caot be worked by multiple people at the same time. If you wat to discoect the Etheret LAN cable, you should termiate all of the termial emulator that you have started up. The, discoect the Etheret LAN cable. Whe all setups are completed, retur to the system status scree. Tur the power of the primary statio off ad the o agai. Note that if IXS-6600/IXS-6700 is the primary statio, whe the power turs o or off, the cross-poit sigal is cut for a istat. The sigal is ot cut if the primary statio is HKSP-R80. Whe the IXS-6600/IXS-6700 is Used as the Secodary Statio 1. Settig the IXS-6600/IXS-6700 as the secodary statio Set the P/S switch Note) o the CPU board of the IXS- 6600/IXS-6700. (Refer to the Istallatio Maual.) 2. Settig the statio ID Set the switch to the desired statio ID i the rage of 2 to 254 so that it is ot duplicated with the statio IDs of other secodary equipmet. 3. Settig the primary statio equipmet Set the P/S switch Note) o the CPU board of the primary statio equipmet to the [P] positio. 4. Coectig the primary statio equipmet to the other secodary statio equipmet Coect the REMOTE 1 coectors each other usig the BNC coaxial cables. 5. Set a persoal computer (Settig the F1 to F5 code) Set the codes of F1 to F5 i accordace with the followig table referrig to the documet of termial emulator. Key Name Commad HEX Data F1 F1 ESC [ 17 ~ 1B, 5B, 31, 37, 7E F2 F2 ESC [ 18 ~ 1B, 5B, 31, 38, 7E F3 F3 ESC [ 19 ~ 1B, 5B, 31, 39, 7E F4 F4 ESC [ 20 ~ 1B, 5B, 32, 30, 7E F5 F5 ESC [ 21 ~ 1B, 5B, 32, 31, 7E *ESC =16 hexadecimal umber 1B 10 decimal umber 27 6. Coectig the persoal computer to the primary statio equipmet Coect the persoal computer to the REMOTE 3 coector usig the RS-232C cable. 7. Set the commuicatio coditios of the persoal computer Trasfer speed : 38.4 kbps, Data bit : 8 bits, No parity, No check. 8. Turig o the power Tur o the power of all the equipmet o the S-BUS data lik. The system status scree appears o the persoal computer moitor. (Refer to Sectio 2-3.) Wait for about oe miute or more after turig o the power, before startig the settig. Operatio of the equipmet may be ustable immediately after the power is tured o. 9. Let the secodary statio meu scree appear o display. (Refer to Sectio 2-3.) Whe the [Ctrl] _ [X] are pressed o the system status scree, the display shows the primary statio meu scree. Whe you wat to call the meu scree of the IXS- 6600/IXS-6700 that is the secodary statio, select the [R: CALL SECONDARY STATION] from the primary statio meu scree. The eter the statio ID of the IXS-6600/IXS-6700. Perform the respective setups of Sectio 2-5 from the secodary statio meu scree. Whe all setups are completed, retur to the system status scree. Tur the power of the primary statio off ad the o agai. Note) I IXS-6600/IXS-6700, P/S switch o CPU board meas S1203-3 o the CA-65 board. IXS-6600/6700 2-3
2-3. Display Screes, ad Movig betwee the Display Screes The setup display cosists of the followig three types of scree.. System status scree : Displays the status i which the routig system is operatig.. Meu scree : Displays the meu for settig the router system.. Settig scree : Displays the settig items of each meu. System status scree [Ctrl] _ [X] [Ctrl] _ [X] or [Ctrl] _ [B] Meu scree *2 [Ctrl] _ [D] Meu scree [Ctrl] _ [Z] *1 [Ctrl] _ [E] *1 [Ctrl] _ [D] [Ctrl] _ [E] Settig scree [Ctrl] _ [D] Settig scree Settig of the primary statio Settig of the secodary statio [Ctrl] _ [D] *2 Meu scree *1 [Ctrl] _ [E] Settig scree Settig of the tertiary statio *1 : The meu items ca be selected i the followig two ways. See the Meu scree o the ext page. *2 : See the Meu scree/secodary statio o page 2-6. 2-4 IXS-6600/6700
System Status Scree The system status scree appears whe the mai power of the primary statio is tured o. Whe [Ctrl] _ [X] are pressed, the meu scree appears. Whe [Ctrl] _ [X] or [Ctrl] _ [B] are pressed o the meu scree, the display returs to the system status scree. Whe password is set, a message appears promptig you to eter password whe [Ctrl] _ [X] are pressed to eter the meu scree. Eter the correct password. SONY INTEGRATED ROUTING SYSTEM IXS-6700 V1.0 ITEM ROM CHECK SUM A43F RAM READ AND WRITE OK REFERENCE SIGNAL OK S-BUS LINK TERMINATE REAL TIME CLOCK OK STARTED Ctrl-X to SYSTEM SETUP MENU 2001.06.23-20.16 S-BUS LINK DISCONNECTED TO CHANNEL A 2001.06.23-20.16 S-BUS LINK DISCONNECTED TO CHANNEL B1 2001.06.23-20.16 S-BUS LINK DISCONNECTED TO CHANNEL B2 System status scree whe the mai power is tured o (IXS-6600/IXS-6700) O the system status scree, result of the self-diagostics that is performed at the power-o is displayed. The status messages are displayed while the system is operatig. Refer to 3-2. Fuctio Check. Meu Scree The meu scree appears whe [Ctrl] _ [X] are pressed o the system status scree. (Primary statio meu scree) All of the meu items that are used for system setup are displayed o the primary statio meu scree. Whe a meu item is selected by ay of the followig methods, the display chages to the settig scree.. Select the desired meu item with the cursor key ad press [Eter]. (There are some termial emulators that caot execute this method.). Press the alphabet keys that are assiged to the respective meu items. Perform the respective settigs that are show i Sectio 2-4 o the primary statio meu scree. SONY ROUTING SYSTEM SETUP MENU IXS-6700 V1.00 STATION NUMBER 1 MODIFICATION COMMAND A: SET CONTROL AREA B: SET SOURCE/DEST TYPE C: SET DESTINATION NAME D: SET SOURCE NAME E: SET LEVEL TABLE F: SET ACTIVE UNIT NUMBER G: UPDATE BACKUP CONTROLLER H: SET GLOBAL PHANTOM I: SET INDEX NUMBER J: NAME STYLE(Type + Num ) L: SET PHYSICAL ASSIGNMENT M: SET INHIBIT TABLE N: SET DESCRIPTION NAME GROUP O: SET TIE LINES Q: CHANGE CROSSPOINT R: CALL SECONDARY STATION S: SET SOURCE ASSIGNMENT MAINTENANCE COMMAND P: CHANGE PASSWORD T: SET CLOCK U: DISPLAY ETHERNET STATION W: SYSTEM STATUS LOG X: DISPLAY S-BUS COMMUNICATION Z: SET UNIT DETECTABLE Ctrl-X/B:QUIT SETUP MENU Primary statio meu scree (IXS-6600/IXS-6700) Whe [Ctrl] _ [X] or [Ctrl] _ [B] are pressed o the primary statio meu scree, the display returs to the system status scree. IXS-6600/6700 2-5
Meu scree/secodary statio Whe you wat to call the secodary statio meu scree, select the [R: CALL SECONDARY STATION] from the meu of the primary statio ad eter the statio ID of the secodary statio. Whe you wat to set the secodary statio fuctio ito the primary statio routig switcher, eter 1 as the statio ID of the secodary statio. Perform the respective settigs that are show i Sectio 2-5 o the secodary statio meu scree. Whe [Ctrl] _ [D] are pressed o the secodary statio meu scree, the display returs to the primary statio meu scree. Respose of the routig switcher system becomes slower while the meu scree or the setup scree is beig displayed whe compared with the respose o the system status scree. For avoidig this trouble, retur the display to the system status scree whe the settig up is completed. SONY ROUTING SYSTEM SETUP MENU IXS-6700 V1.00 STATION NUMBER 1 MODIFICATION COMMAND A: SET UNIT LOCATION K: RESET TO DEFAULT TABLE W: SAVE CURRENT TABLE MAINTENANCE COMMAND V: DISPLAY UNIT STATUS Y: DISPLAY TABLE DATA Z: SET SIGNAL Ctrl-D:RETURN Secodary statio meu scree (IXS-6600/IXS-6700) Settig Scree The settig scree appears whe ay of the setup item is selected from the primary statio or the secodary statio meu scree. The actual settig is performed o this scree. Because the screes are differet depedig upo the settig items, the scree examples are show i the respective settig items (Sectios 2-4 ad 2-5.) Whe [Ctrl] _ [E] are pressed o the secodary statio settig scree, the display returs to the secodary statio meu scree. Whe [Ctrl] _ [D] are pressed, the display returs to the primary statio meu scree. Whe [Ctrl] _ [E] are pressed o the primary statio settig scree, the display returs to the primary statio meu scree. Respose of the routig switcher system becomes slower while the meu scree or the setup scree is beig displayed whe compared with the respose o the system status scree. For avoidig this trouble, retur the display to the system status scree whe the settig up is completed. 2-6 IXS-6600/6700
2-4. Settig Items of the Primary Statio A : SET CONTROL AREA Purpose Sets the sources rage ad the destiatios rage of the whole routig switcher system to be cotrolled by the primary statio. A arbitrary ame of primary statio for this cotroller ca also be set o this scree. Settig procedure 1. Select [A] from the meu scree. 2. Select the desired settig item usig the cursor. 3. Press [Eter]. Rage of sources, rage of destiatios, ad ame (item [NAME]) for the primary statio become ready to be set. 4. Eter the rage of sources ad the rage of destiatios usig the umeric keys. Iput the desired ame for primary statio usig alphaumeric keys (four characters at a maximum). The maximum values that ca be set for the rage of sources ad for the rage of destiatios are show below. Source Maximum value 4093 4093 that ca be set Maximum size (rage) 1024 1024 that ca be set Example : 1025-2048 (Setup size 1024): OK 0001-2048 (Setup size 2048): NG Destiatio 5. Press [Eter]. The setup values are registered. If [Ctrl] _ [F] are pressed before pressig the [Eter], the values retur to the origial value before eterig the data. Operatig fuctio keys [F1] : MODIFY Press [F1]. The source value ad the destiatio value that are assiged to the idex umber (IN- DEX) idicated by the meu item I: SET INDEX NUMBER are chaged. The top values of the source ad destiatio rages that are set by this meu are added respectively to the values set as the source ad destiatio by the meu item I. For example, assume that case that you set the source to SOURCE No. 0001-1025. If the top value of the source chaged from 0001 to 1024, the differece betwee the top values becomes 1024 (1025 _ 1 = 1024). Whe the origial idicatio of SRC i the meu item I starts with 0001, 0002, 1001, 1002, ad so o, the idicatio is chaged to 1025, 1026, 2025, 2026, ad so o after [F1] is executed. This occurs because the differece betwee the top values (i.e., 1024 i this example) is added to every source umber. The cotrol area of the meu item [A] meas the cotrol area of the whole routig system, ad ot the iput/output areas of the primary statio routig switcher. To set the locatio of the iput/output termial of the primary statio routig switcher, call the secodary statio meu scree by selectig [R : CALL SECONDARY STATION] from the meu scree ad type the statio umber [1], ad the select [A : SET UNIT LOCATION]. To retur to the meu scree Press [Ctrl] _ [E]. SET CONTROL AREA IXS-6700 V1.00 STATION NUMBER 1 SOURCE No 0001-1024 DESTINATION No 0001-1024 LEVEL 1-8 NAME HOGE F1:MODIFY Ctrl-E:RETURN TO MENU IXS-6600/6700 Example of settig scree 2-7
B : SET SOURCE/DEST TYPE Purpose Sets the type ame of the source ad destiatio, ad that of the global phatom. (For details about the type ame, refer to Appedix B Type + Number ame mode (Type + Num)). Set the type ames i accordace with the types ad usage of the iput/output sigals. Settig procedure of type ame 1. Select [B] from the meu scree. 2. Use the cursor or alphabet/umerical keys ad select the codes for the type ame to be registered from the 32 character codes (0 to 9 ad A to V) displayed o the scree. 3. Whe [Ctrl] _ [P] are pressed, the settig of the type ame will be caceled, ad.... will be displayed. 4. Press [Eter] to eter the type ame etry mode. To cacel the type ame etry mode, press [Eter] before iputtig the type ame. The scree shows.... ad the cursor moves to the ext code. 5. Use the alphabet ad umerical keys to eter the type ame (withi four letters). 6. Press [Eter]. The type ame is set ad the cursor moves to the ext positio. If [Ctrl] _ [F] are pressed before the settig, the type ame returs to the origial type ame before etry. Settig procedure of umber of types 1. Press [F1]. [Do you chage the type umber? Y or N] appears. 2. Press [Y]. Number of types is chaged to 16. If you wat to retur the umber of types to 32, repeat steps 1 ad 2. If umber of types is chaged from 32 to 16, ames of the termials to which the type umber of 17 to 32 are give, caot be retured to the origial ames. The termial ame from No. 1 to No. 512. TYPE : 16 The ames up to 16 types ca be used. Whe the S-P1 type remote cotrol pael or the display uit is used i the system, select the TYPE 16.. TYPE : 32 The ames up to 32 types ca be used. Whe the S-P1 type remote cotrol pael or the display uit is used i the system, the correct display or correct operatio caot be performed. Name of the termials from No.513 to No.1024 are fixed to type 32 without affected by this settig. To retur to the meu scree Press [Ctrl] _ [E]. SOURCE/DEST/PHANTOM TYPE IXS-6700 V1.00 STATION NUMBER 1 TYPE:32 0=IN 1=OUT 2=... 3=... 4=... 5=... 6=... 7=... 8=... 9=... A=... B=... C=... D=... E=... F=... G=... H=... I=... J=... K=... L=... M=... N=... O=... P=... Q=... R=... S=... T=... U=... V=... F1:TYPE Ctrl-E:RETURN TO MENU Example of settig scree 2-8 IXS-6600/6700
C : SET DESTINATION NAME Purpose Sets the destiatio ame ad protect fuctio of each output. (For details about the protect fuctio, refer to Appedix B Protect.) A umber betwee 001 to 999 ad a type ame set at the meu item [B : SET SOURCE/DEST TYPE] ca be set to each destiatio as the destiatio ame. Descriptio ame ca be set by chagig the ame mode at the meu item [J : NAME STYLE]. For details of settig the ame, refer to [J] i the meu. (For details about the Descriptio ame, refer to Appedix B Descriptio ame mode.) Settig procedure of destiatio ame 1. Select [C] from the meu scree. 2. Press the cursor keys or the fuctio keys to select the desired destiatio umber. 3. Press [Ctrl] _ [P]. The set destiatio ame will be deleted ad.... will be displayed. 4. Press [Eter]. The destiatio ame ca be typed. If [Eter] is pressed agai before eterig a ame, the etry will be caceled ad the cursor moves to the ext termial umber. 5. Select a type ame that you wat to set, from the correspodig code (0 to 9, A to V) i the bottom of scree ad type the code. The type a umber (0 to 999) that you wat to set usig umeric keyboard. 000 caot be added to the ame of the type umber 0. For example, i the case of 0=IN (the ame of the type umber 0 is IN), IN000 caot be set. Settig procedure of protect fuctio 1. Select the destiatio ame usig the cursor, ad the press [P]. P is displayed after the selected destiatio ame ad the protect fuctio is set. Protect fuctio caot be set for a umber whose destiatio ame has ot bee assiged. 2. To release the protect fuctio, select the destiatio ame ad press [P] oce agai. m. If a destiatio ame is high-lighted, it idicates that the protect fuctio is set from cotrol termial. If the protect is set from a remote cotrol pael, the destiatio ame is ot high-lighted.. To chage the protected destiatio ame, release the protectio first before begiig the modificatio process. DESTINATION NUMBER TRANSCODE IXS-6700 V1.00 STATION NUMBER 1 0001=OUT001 0002=OUT002 0003=OUT003 P 0004=OUT004 P 0005=OUT005 0006=OUT006 0007=OUT007 0008=OUT008 0009=OUT009 0010=OUT010 0011=OUT011 0012=OUT012 0013=OUT013 0014=OUT014 0015=OUT015 0016=OUT016 0017=OUT017 0018=OUT018 0019=OUT019 0020=OUT020 0021=OUT021 0022=OUT022 0023=OUT023 0024=OUT024 0025=OUT025 0026=OUT026 0027=OUT027 0028=OUT028 0029=OUT029 0030=OUT030 0031=OUT031 0032=OUT032 0033=OUT033 0034=OUT034 0035=OUT035 0036=OUT036 0037=OUT037 0038=OUT038 0039=OUT039 0040=OUT040 0041=OUT041 0042=OUT042 0043=OUT043 0044=OUT044 0045=OUT045 0046=OUT046 0047=OUT047 0048=OUT048 0049=OUT049 0050=OUT050 0051=OUT051 0052=OUT052 0053=OUT053 0054=OUT054 0055=OUT055 0056=OUT056 0057=OUT057 0058=OUT058 0059=OUT059 0060=OUT060 0061=OUT061 0062=OUT062 0063=OUT063 0064=OUT064 0=IN 1=OUT 2=VTR 3=ENG 4=MCR 5=TEST 6=SNG 7=SS 8=CG 9=SAT A=LMS B=EDIT C=CAM D=GPHA E=GPHB F=GPHC G=17 H=18 I=19 J=20 K=21 L=22 M=23 N=24 O=25 P=26 Q=27 R=28 S=29 T=30 U=31 V=32 F1:SEARCH F2:JUMP F3:PgUp F4:PgD P:PROT. Ctrl-E:RETURN TO MENU Example of settig scree 6. Press [Eter]. The destiatio ame will be set ad the cursor moves to the ext termial umber. If [Ctrl] _ [F] are pressed before the settig, the origial destiatio ame will be retured. The same destiatio ame caot be set at more tha two destiatios. If this is doe, a error message will be displayed at the bottom of the scree. Display example : * * * * * is used already; Igored Destiatio ame IXS-6600/6700 2-9
Operatig fuctio keys [F1] : SEARCH (To move the cursor to the desired destiatio ame.) 1. Press [F1]. Please Iput DEST NAME = will be displayed. 2. Iput the destiatio ame ([Code umber i the bottom of the scree] + [umeral (0 to 999]) to be retrieved. 3. Press [Eter]. The cursor will move to the desired destiatio ame. Whe meu item [J] is set to the Descriptio ame mode, [F1] (SEARCH) will have the followig fuctios. 1. Press [F1]. Please Iput DEST NAME = will be displayed. 2. Eter the Descriptio ame (withi seve characters) from the head. 3. Press [Eter]. The Descriptio ame etered will be searched ad the page icludig the ame appears o the scree. 4. If the desired ame does ot exist i the scree, press [F1] agai. The the cursor moves to the ext descriptio ame cotaiig the character strig that you wat to retrieve. [F2] : JUMP (To move the cursor to the destiatio umber.) 1. Press [F2]. Please Iput DEST NUMBER = will be displayed. 2. Iput the destiatio umber to be retrieved. 3. Press [Eter]. The cursor will move to the desired umber. [F3] : PgUp Whe [F3] is pressed, the scree will display the 16 lies previous to the 16 lies displayed curretly. [F4] : PgD Whe [F4] is pressed, the scree will display the 16 lies ext to the 16 lies displayed curretly. To retur to the meu scree Press [Ctrl] _ [E]. D : SET SOURCE NAME Purpose Sets the source ame ad secret fuctio. (For details about the secret fuctio, refer to Appedix B Secret.) A umber betwee 001 to 999 ad a type ame set at the [B : SET SOURCE/DEST TYPE] ca be set to each source ame. Descriptio ame ca be set by chagig the ame mode at [J : NAME STYLE] i the meu. For details of settig the ame, refer to [J] i the meu. (For details about the Descriptio ame, refer to Appedix B Descriptio ame mode.) Settig procedure of source ame 1. Select [D] from the meu scree. 2. Select a termial umber of source you wat to set usig the cursor key or fuctio key. 3. Press [Ctrl] _ [P]. The set source ame will be deleted, ad.... will be displayed. 4. Press [Eter]. The etry mode of source ame is set. If [Eter] is pressed before iputtig the source ame, the etry mode is cacelled ad the idicatio chages to...., ad the cursor moves to the ext termial umber. 5. Select a type ame that you wat to select from the correspodig code (0 to 9, A to V) i the bottom of scree ad type the code. The type a umber (0 to 999) that you wat to set usig umeric keyboard. 000 caot be added to the ame of the type umber 0. For example, i the case of 0=IN (the ame of the type umber 0 is IN), IN000 caot be set. 6. Press [Eter]. The iput source ame is set ad the cursor moves to the ext termial umber. If [Ctrl] _ [F] are pressed before the settig, the source ame returs to the origial source ame before etry. The same ame caot be give to assiged to two or more sources. If this is doe, a error message will be displayed at the bottom of the scree. Display example : * * * * * is used already; Igored Source ame 2-10 IXS-6600/6700
Settig procedure of secret fuctio 1. Select the source ame usig the cursor, ad press [S]. S is displayed after the source ame, ad the secret is set. Secret caot be set for a umber whose source ame has ot bee assiged. 2. To release the secret fuctio, select the source ame ad press [S] oce agai. SOURCE NUMBER TRANSCODE IXS-6700 V1.00 STATION NUMBER 1 0001=IN001 0002=IN002 0003=IN003 S 0004=IN004 S 0005=IN005 0006=IN006 0007=IN007 0008=IN008 0009=IN009 0010=IN010 0011=IN011 0012=IN012 0013=IN013 0014=IN014 0015=IN015 0016=IN016 0017=IN017 0018=IN018 0019=IN019 0020=IN020 0021=IN021 0022=IN022 0023=IN023 0024=IN024 0025=IN025 0026=IN026 0027=IN027 0028=IN028 0029=IN029 0030=IN030 0031=IN031 0032=IN032 0033=IN033 0034=IN034 0035=IN035 0036=IN036 0037=IN037 0038=IN038 0039=IN039 0040=IN040 0041=IN041 0042=IN042 0043=IN043 0044=IN044 0045=IN045 0046=IN046 0047=IN047 0048=IN048 0049=IN049 0050=IN050 0051=IN051 0052=IN052 0053=IN053 0054=IN054 0055=IN055 0056=IN056 0057=IN057 0058=IN058 0059=IN059 0060=IN060 0061=IN061 0062=IN062 0063=IN063 0064=IN064 0=IN 1=OUT 2=VTR 3=ENG 4=MCR 5=TEST 6=SNG 7=SS 8=CG 9=SAT A=LMS B=EDIT C=CAM D=GPHA E=GPHB F=GPHC G=17 H=18 I=19 J=20 K=21 L=22 M=23 N=24 O=25 P=26 Q=27 R=28 S=29 T=30 U=31 V=32 F1:SEARCH F2:JUMP F3:PgUp F4:PgD S:SECRET Ctrl-E:RETURN TO MENU Example of settig scree Operatig fuctio keys [F1] : SEARCH (To move the cursor to the desired source ame.) 1. Press [F1]. Please Iput SOURCE NAME = will be displayed. 2. Iput the source ame ([Code umber i the bottom of the scree] + [umeral (0 to 999]) to be retrieved. 3. Press [Eter]. The cursor will move to the desired source ame. Whe meu item [J] is set to the Descriptio ame mode, [F1] (SEARCH) will have the followig fuctios. 1. Press [F1]. Please Iput SOURCE NAME = will be displayed. 2. Eter the Descriptio ame (withi seve characters) from the head. 3. Press [Eter]. The correspodig Descriptio ame will be searched i the rage of the etered characters ad the page icludig the ame appears o the scree. 4. If the desired ame does ot exist i the scree, press [F1] agai. The the cursor moves to the ext descriptio ame cotaiig the character strig that you wat to retrieve. [F2] : JUMP (To move the cursor to the source umber.) 1. Press [F2]. Please Iput SOURCE NUMBER= will be displayed. 2. Iput the source umber to be retrieved. 3. Press [Eter]. The cursor will move to the desired umber. [F3] : PgUp Whe [F3] is pressed, the scree will display the 16 lies previous to the 16 lies displayed curretly. [F4] : PgD Whe [F4] is pressed, the scree will display the 16 lies ext to the 16 lies displayed curretly. To retur to the meu scree Press [Ctrl] _ [E]. IXS-6600/6700 2-11
E : SET LEVEL TABLE Purpose Sets level ame, sets whether the levels that are set for the respective termials are made valid or ivalid, ad sets umber of levels. Level ame settig procedure 1. Select [E] from the meu scree. 2. Press the cursor keys to select the level umber. 3. Press [Eter] to eter the level ame etry mode. 4. Eter the level ame usig the alphabet ad umerical keys (withi four characters). 5. Press [Eter]. The level ame will be set. If [Ctrl] _ [F] are pressed before the settig, the origial level ame will be retured. LEVEL TABLE IXS-6700 V1.00 STATION NUMBER 1 LEVEL:1-16 1=VIT 2=A1 3=A2 4=TC 5=REM 6=B32 7=... 8=... 9=... 10=... 11=... 12=... 13=... 14=... 15=... 16=... No. out VIT A1 A2 TC REM B32...... 0001 OUT001 VIT A1.................. 0002 OUT002 VIT A1.................. 0003 OUT003 VIT A1 A2 TC REM B32...... 0004 OUT004 VIT A1 A2 TC REM B32...... 0005 OUT005 VIT A1 A2 TC REM B32...... 0006 OUT006 VIT A1 A2 TC REM B32...... 0007 OUT007 VIT A1 A2 TC REM B32...... 0008 OUT008 VIT A1 A2 TC REM B32...... 0009 OUT009 VIT A1 A2 TC REM B32...... 0010 OUT010 VIT A1 A2 TC REM B32...... 0011 OUT011 VIT A1 A2 TC REM B32...... 0012 OUT012 VIT A1 A2 TC REM B32...... 0013 OUT013 VIT A1 A2 TC REM B32...... 0014 OUT014 VIT A1 A2 TC REM B32...... 0015 OUT015 VIT A1 A2 TC REM B32...... 0016 OUT016 VIT A1 A2 TC REM B32...... 0017 OUT017 VIT A1 A2 TC REM B32...... F1:SEARCH F2:JUMP F3:LEVEL F4:ENA Example of settig scree Ctrl-E:RETURN TO MENU Procedure to make the levels valid or ivalid Whe level ames are set, these ames appear automatically i the level colum of the respective output termials. I this status, all the levels are set to be valid at each output termial. If you wat to make the level ivalid, move the cursor to the level ame that you wat to make ivalid ad press [Eter]. The level ame chaged to.... ad the settig of the level is made ivalid. If you wat to retur the ivalidated level to valid, move the cursor to.... ad press [Eter]. The origial level will be restored. If the destiatio ame is ot set, the umber of the destiatio will ot be displayed. Settig umber of levels Every pressig of [F3] toggles betwee the LEVEL: 1-8 display ad the LEVEL : 1-16 display o the 2d lie. About LEVEL: 1-16 Whe the system is used with the LEVEL 1-16, the remote cotrol pael that supports the LEVEL 1-16 becomes ecessary. The LEVEL 9-16 is realized by switchig the Destiatio to which 512 is added, at the same time. (For example, whe switchig termial umber 1 of the destiatio of LEVEL 9-16, termial umber 513 of the destiatio is also switched.) Operatig fuctio keys [F1] : SEARCH (To move the cursor to the desired destiatio ame.) 1. Press [F1]. Please Iput DEST NAME = will be displayed. 2. Iput the destiatio ame ([Code umber i the bottom of the scree] + [umeral (0 to 999]) to be retrieved. 3. Press [Eter]. The cursor will move to the desired destiatio ame. Whe meu item [J] is set to the Descriptio ame mode, [F1] (SEARCH) will have the followig fuctios. 1. Press [F1]. Please Iput DEST NAME = will be displayed. 2. Eter the Descriptio ame (withi seve characters) from the head. 3. Press [Eter]. The correspodig Descriptio ame will be searched i the rage of the etered characters ad the page icludig the ame appears o the scree. 4. If the desired ame does ot exist i the scree, press [F1] agai. The the cursor moves to the ext descriptio ame cotaiig the character strig that you wat to retrieve. [F2] : JUMP (To move the cursor to the umber of the desired destiatio.) 1. Press [F2]. Please Iput DEST NUMBER =, will be displayed. 2. Iput the destiatio umber to be retrieved. 3. Press [Eter]. The cursor will move to the desired destiatio umber. 2-12 IXS-6600/6700
[F3] : LEVEL (Display is switched betwee LEVEL : 1-8 ad LEVEL : 1-16.) Each time [F3] is pressed, the scree display toggles betwee LEVEL : 1-8 ad LEVEL : 1-16 o the 2d lie. [F4:ENA] (ENABLE/DISABLE) O the termial meu Q: CHANGE CROSSPOINT scree (to be abbreviated simply as Q scree hereuder), the cross-poits ca be switched i the same way as from remote cotroll pael. Whe the F4 display is DISABLE, the termial meu E: SET LEVEL TABLE setup (specifyig which level is used for switchig the respective outputs) is reflected o the operatios o the Q scree. For example, whe the output No. 57 is set to level 3 oly from the E scree, oly the level 3 commad is output whe the output No. 57 is switched from the All Level Selector scree of the Q scree. Whe the F4 display is ENABLE, the setup of the E scree will ot affect operatios of the Q scree. Wheever [F4] is pressed, the display is toggled betwee [F4:ENA] ad [F4:DIS]. To retur to the meu scree Press [Ctrl] _ [E]. F : SET ACTIVE UNIT NUMBER Purpose Eables the uits that are coected to the S-BUS data lik for mutual commuicatio with S-BUS protocol. (For details, refer to Appedix B Active: Decide remote cotrol paels that ca be active o the S-BUS.) Settig procedure 1. Select [F] from the meu scree. 2. Select the statio ID of the secodary statio that you wat to make the commuicatio valid usig the cursor key. For example, if you wat to set the statio ID21, select the lie 1 from the lies 021-040. 3. Every time the [Eter] butto is pressed, it toggles betwee E ad blak. Select E to make the commuicatio valid. The display M meas the primary statio. 255 ad later, which are outside of the coectio rage, is displayed as *. Whe [A] is pressed, all commuicatios are made valid. Whe [C] is pressed, all commuicatio are made ivalid. The respose will become slower if there are may secodary statios. ENABLE ACTIVE UNIT FOR STATION NUMBER IXS-6700 V1.00 STATION NUMBER 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 + 001-020 M E E E E E E E E E E E E E E E E E E E 021-040 E E E E E E E E E E E E E E E E E E E E 041-060 E E E E E E E E E E E E E E E E E E E E 061-080 E E E E E 081-100 101-120 121-140 141-160 161-180 181-200 201-220 221-240 241-254 * * * * * * Example of settig scree Ctrl-E;RETURN TO MENU To retur to the meu scree Press [Ctrl] _ [E]. IXS-6600/6700 2-13